Infrared chemiluminescence study of CO2 formation in CO + NO reaction on Pd(110) and Pd(111) surfaces

Infrared (IR) chemiluminescence studies of CO2 formed during steady-state CO + NO reaction over Pd(110) and Pd(111) surfaces were carried out. Kinetics of the CO + NO reaction were studied over Pd(110) using a molecular-beam reaction system in the pressure range of 10-2-10-1 Torr. The activity of the CO + NO reaction on Pd(110) was much higher than that of Pd(111), which was quite different from the result of other experiments under a higher pressure range. On the basis of the experimental data on the dependence of the reaction rate on CO and NO pressures and the reaction rate constants obtained by using a reaction model, the coverage of NO, CO, N, and O was calculated under various flux conditions. From the analysis of IR emission spectra in the CO + O2 reaction on Pd(110) and Pd(111), the antisymmetric vibrational temperature (TVAS) was seen to be higher than the bending vibrational temperature (TVB) on Pd(110). In contrast, TVB was higher than TVAS on Pd(111). These behaviors suggest that the activated complex for CO2 formation is more bent on Pd(111) than that on Pd(110), which is reflected by the surface structure. Both TVB and TVAS for the CO + O2 reaction on Pd(110) and Pd(111) increased gradually with increasing surface temperature (TS). On the other hand, in the case of the CO + NO reaction on Pd(110) and Pd(111), TVAS decreased and TVB increased significantly with increasing TS. TVB was lower than TVAS at lower TS, while TVB was higher than TVAS at higher TS. Comparison of the data obtained for the two reactions indicates that TVB in the CO + NO reaction on Pd(110) at TS = 800 and 850 K is much higher than that in the CO + O2 reaction on Pd(110).     

Adsorption of carbon monoxide on Pd (210) and (510) surfaces

Adsorption of carbon monoxide on Pd (210) and (510) stepped surfaces has been investigated by the extended London‐Eyring‐Polyani‐Sato method constructed using a five‐parameter Morse potential. Pd (210) and (510) stepped surfaces consist of terrace with (100) structure and step with (110) character. These results show that there exist common characteristics of CO adsorption on these two surfaces. At low coverage, CO adsorbs in twofold bridge site of the (100) terrace. The critical characteristics inherit that of CO molecule adsorbed in twofold bridge site of (100) original surface. When the coverage is increased, the top site of (110) step is occupied. The critical characteristics resemble that of CO molecule adsorbed in top site of (110) original surface. A number of new sites are exposed on the boundary regions, for example, the fivefold hollow site (H) of these two surfaces. There are stable adsorption sites at high coverage. Because of the different length of the (100) terrace, the (210) and (510) stepped surfaces have some different characteristics. First, CO is tilted adsorption on bridge site of terrace of (210), but perpendicular on terrace of (510) surface. Second, the bridge site (B₁) where one Pd atom at the top of the step and the other at the bottom of the step is a stable adsorption site on (210), but the same type of site on Pd (510) surface is not. Copyright © 2012 John Wiley & Sons, Ltd.     

Structure of activated complex of CO2 formation in a CO + O2 reaction on Pd(110) and Pd(111)

Examinations of CO2 formed during steady-state CO oxidation reactions were performed using infrared (IR) chemiluminescence. The CO2 was formed using a molecular-beam method over Pd(110) and Pd(111). The CO2 formation rate is temperature dependent under various partial pressure conditions. The temperature of the maximum formation rate is denoted as TSmax. Analyses of IR emission spectra at surface temperatures higher than TSmax showed that the average vibrational temperature (TVAV) is higher for Pd(111) than for Pd(110). The antisymmetric vibrational temperature (TVAS) is almost equal on both surfaces. These results suggest that the activated CO2 complex is more bent on Pd(111) and straighter on Pd(110). Furthermore, the difference in the TVAV value was small for surface temperatures less than TSmax. The TVAS value was much higher than TVAV on both surfaces. These phenomena were observed only when the surface temperature was lower than TSmax: they became more pronounced at lower temperatures, suggesting that the activated complex of CO2 formation is much straighter on both Pd surfaces than that observed at higher surface temperatures. Combined with kinetic results, the higher CO coverage at the lower surface temperatures is inferred to be related to the linear activated complex of CO2 formation.     

Theoretical study of NO adsorption/dissociation on Pd (100) and (111) surfaces

Both adsorption and dissociation of the diatomic molecular NO on Pd (100) and (111) surfaces are studied using the extended London‐Eyring‐Polyani‐Sato (LEPS) method constructed by means of 5‐MP (the 5‐parameter Morse potential). All critical characteristics of the system that we obtain, such as adsorption geometry, binding energy, eigenvalues for vibration, are in good agreement with the experimental results. On Pd (100) surface, NO prefers to adsorb in fourfold hollow site (H) uprightly at low coverage. With increase in the coverage NO gradually tilts in fourfold hollow and bridge sites. For NO? Pd (111) system, two adsorption states are found at low coverage, of which one adsorption state is the B(tilt) state that the centroid of NO projects at bridge site, another (H? B? H state) that NO almost parallels to the (111) surface with the vibration frequency of 610 cm^?1, but the frequency is near to that of the atoms, which is easy to be ignored in experiments. At high coverage, two transitional states (BH and HT) are found. NO is difficult to dissociate on Pd (100) and (111) surfaces. Especially for NO? Pd (111) system, the three‐well‐potential dissociation mode is initially put forward to show the remarkable dissociation process with two dissociation transitional states of NO on Pd (111). Copyright © 2008 John Wiley & Sons, Ltd.     

First-principles analysis of the effects of alloying Pd with Ag for the catalytic hydrogenation of acetylene-ethylene mixtures

The effect of alloying Pd with Ag on the hydrogenation of acetylene is examined by analyzing the chemisorption of all potential C(1) (atomic carbon, CH, methylene, and methyl) and C(2) (acetylene, vinyl, ethylene, ethyl, ethane, ethylidene, ethylidyne, and vinylidene) surface intermediates and atomic hydrogen along with the reaction energies for the elementary steps that produce these intermediates over Pd(111), Pd(75%)Ag(25%)/Pd(111), Pd(50%)Ag(50%)/Pd(111), and Ag(111) surfaces by using first-principle density functional theoretical (DFT) calculations. All of the calculations reported herein were performed at 25% surface coverage. The adsorption energies for all of the C(1) and C(2) intermediates decreased upon increasing the composition of Ag in the surface. Both geometric as well as electronic factors are responsible for the decreased adsorption strength. The modes of adsorption as well as the strengths of adsorption over the alloy surfaces in a number of cases were characteristically different than those found over pure Pd (111) and Ag (111). Adsorbates tend to minimize their interaction with the Ag atoms in the alloy surface. An electronic analysis of these surfaces shows that there is, in general, a shift in the occupied d-band states away from the Fermi level when Pd is alloyed with Ag. The s and p states also appear to contribute and may be responsible for small deviations from the Hammer-N?rskov model. The effect of alloying is more pronounced on the calculated reaction energies for different possible surface elementary reactions. Alloying Pd with Ag reduces the exothermicity (increases endothermicity) for bond-breaking reactions. This is consistent with experimental results that show a decrease in the decomposition products in moving from pure Pd to Pd-Ag alloys.(2-5) In addition, alloying increases the exothermicity of bond-forming reactions. Alloying therefore not only helps to suppress the unfavorable decomposition (bond-breaking) reaction rates but also helps to enhance the favorable hydrogenation (bond-forming) reaction rates.     

A density functional study of NO adsorption and decomposition on Ni(211) and Pd(211) surfaces

The adsorption and decomposition of NO have been investigated by using density functional theory method at the generalized gradient approximation level. We have performed calculations on adsorption energies and structures of NO on Ni(211) and Pd(211) surfaces with full-geometry optimization and compared them with the experimental data. The most favorite adsorption on both surfaces occurs at the bridge site parallel to step edge (sb), while the energy difference from the second favorite site of a threefold hollow site near step edge is less than 0.1 eV. Decomposition pathways have been investigated with transition state search. The decomposition pathway, where NO leans toward the step, is most probable for both surfaces. The overall activation energy for decomposition is 0.39 and 1.26 eV for Ni(211) and Pd(211), respectively. The present results clearly show that the NO molecules on Pd(211) are less activated than those on Ni(211). We have studied also reorganization of NO on Pd(211) at higher coverages up to 1/3 ML (monolayer) [three NO molecules in a (3 x 1) unit cell]. The site occupation is not in a sequential manner as the NO coverage is increased, and a reorganization of NO adsorbates occurs (the NO molecule at sb becomes tilting up at higher coverage), which can interpret the experimental data of Yates and co-workers very well.     

甲烷在清洁 Pd(111) 及氧改性的 Pd(111) 表面解离的密度泛函理论研究

 采用广义梯度近似 (GGA) 的密度泛函理论 (DFT) 并结合平板模型, 研究了 CH4 在清洁 Pd(111) 及 O 改性的 Pd(111) 表面发生 C朒 键断裂的反应历程. 优化了裂解过程中反应物、过渡态和产物的几何构型, 获得了反应路径上各物种的吸附能及反应的活化能. 结果表明, CH4 采用一个 H 原子指向表面的构型在 Pd(111) 表面的顶位吸附, CH3 的最稳定的吸附位置为顶位, OH, O 和 H 的最稳定吸附位置均为面心立方. CH4 在清洁 Pd(111) 表面裂解的活化能为 0.97 eV, 低于它在 O 原子改性 (O 没有参与反应) 的 Pd(111) 表面的活化能 1.42 eV, 说明表面氧原子抑制了 CH4 中 C朒 键的断裂. 当亚表面 O 原子和表面 O 原子 (O 参与反应) 共同存在时, C朒 键断裂的活化能为 0.72 eV, 低于只有表层氧存在时的活化能 (1.43 eV), 说明亚表面的 O 原子对 CH4 分子的活化具有促进作用. CH4 在 O 原子改性的 Pd(111) 表面裂解生成 CH3 和 H, 以及生成 CH3 和 OH 的反应活化能分别为 1.42 和 1.43 eV, 说明 CH4 在 O 原子改性的 Pd(111) 表面发生这两种反应的难易程度相当.     

Pd(111), Pd(100)及Pd(110)表面H2和O2直接合成H2O2的密度泛函理论研究

采用周期性密度泛函理论研究了H₂和O₂在Pd(111),Pd(100)及Pd(110)表面上直接合成H₂O₂的反应机理,对反应的主要基元步骤进行了计算和分析.结果表明,Pd(111)表面对H₂O₂直接合成的催化选择性最好,表面原子密度较低的Pd(100)表面和Pd(110)表面上含有O-O键的表面物种解离严重,不利于H₂O₂的生成.H₂O₂的选择性与含有O-O键表面物种的O-O键能和表面物种的结合能有关.含有O-O键的表面物种在表面的结合能越大,越容易发生解离,不利于形成H₂O₂.     

Interaction of coadsorbed CH3Cl and D2O layers on Pd(111) studied by sum frequency generation

Adsorption of methyl chloride and coadsorption of CH3Cl and D2O on Pd(111) surfaces at T=100 K have been studied under ultrahigh-vacuum conditions using femtosecond sum frequency generation (SFG) spectroscopy in the spectral regions of CH and OD bands. On the bare Pd(111) substrate, the CH3Cl coverage dependence of the resonant SFG signal is consistent with a progressive molecular rearrangement starting at half saturation followed by the growth of two ordered monolayers in which the molecular axes are perpendicular to the surface. When CH3Cl is adsorbed on top of predeposited D2O on Pd(111), the SFG signals as a function of the CH3Cl exposure indicate that methyl chloride is adsorbed onto D2O through hydrogen bonding. On the contrary when the adsorption order is reversed the strong decrease of the CH3 signal as a function of the D2O exposure is explained by assuming that water molecules penetrate inside the CH3Cl layers, leading to the formation of disordered CH3Cl clusters. In all cases a nonresonant contribution due to molecular adsorption is observed and it shows a dependence upon surface structure and coverage significantly different from that of the resonant vibrational bands.     

Formation, atomic distribution and mixing energy in two-dimensional Pd(x)Ag(1-x) surface alloys on Pd(111)

The formation and atom distribution in two-dimensional Pd(x)Ag(1-x)/Pd(111) monolayer surface alloys were studied by high resolution scanning tunnelling microscopy (STM) with chemical contrast. From short-range order (SRO) parameters, we calculate preferences for like or unlike nearest neighbours to elucidate the mixing behaviour of the two components for various sub monolayer Ag surface contents. In the regime of low Ag surface contents (<40% Ag), the system shows a weak tendency towards phase separation, high Ag coverages (>60% Ag) result in a disperse distribution of the atoms in the surface. Effective pair interactions (EPIs) were derived by comparing the measured distribution with distributions obtained using Monte Carlo (MC) simulations. From the EPIs, we derived a function for the mixing energy, which can describe the change from clustering to a disperse distribution. The effects of the resulting surface atom distributions and of the Ag coverage dependent surface mixing/demixing on catalytic reactions are discussed.     

Oxygen Atom Adsorption and Diffusion on Pd Low-index Surfaces and （311） Stepped Surface

Introduction Atom adsorption on transition metal surfaces has attracted special attention as a base for understanding the fundamental processes of oxidative catalysis. Particularly interesting is the adsorption and diffusion of oxygen on well-defined metal surfaces. An oxygen covered palladium surface, for example, plays a central role in several important reactions such as oxidation of carbon monoxide and ammonia. In particular, the (100), (111), (110) surfaces and the interactions with oxyge…     

First-principles study of K and Cs adsorbed on Pd(111)

The adsorptions of K and Cs on Pd(111) were studied by the density functional calculations within the generalized gradient approximation. The site preference, bonding character, work function, and electron structure of the system were analyzed. For K and Cs adsorption, the hcp hollow site was found to be preferred for all the coverages investigated. The calculated adsorption geometries for (2 x 2) and (square root 3 x square root 3)R30 degrees phases are both in reasonable agreement with the observed results. The decrease of the work function upon the adsorption of K and Cs can be attributed to a dipole moment associated with the polarized adsorbate atom, which is characterized by depletion of the electron charge in the alkali metal layer and a charge accumulation in the interface region. Our results indicate that the bonding of alkali metal with the Pd(111) surface has a mixed ionic and metallic bond character at low coverage and a metallic bond of covalent character at high coverage.     

Adsorption and Decarbonylation Reaction of Furfural on the Pd(111) and M/Pd(111)(M=Ni,Cu and Ru) Surfaces

By performing with density functional theory(DFT) method, the detailed adsorption process and the catalytic decarbonylation mechanisms of furfural over Pd(111) and M/Pd(111)(M = Ni, Cu, Ru) surfaces toward furan were clarified. The results of atomic size factor, formation energy and d-band center showed that Ru/Pd(111) surface was the most stable and active. The adsorption energies of furfural on the different surfaces followed the order Ru/Pd(111) Cu/Pd(111) Pd(111) Ni/Pd(111). After analyzing Mulliken atomic charge population and the deformation density, we can find that on Ru/Pd(111) surface, the number of charge transfer was the most and the interaction was the strongest. Therefore, its adsorption energy was the highest. Furthermore, the furfural decarbonylation pathway is more kinetically feasible on bimetallic surface, and the reaction is the most likely to occur on Ru/Pd(111).     

First Principles Calculations for Hydrogenation of Acrolein on Pd and Pt: Chemoselectivity Depends on Steric Effects on the Surface

The chemoselective hydrogenation of acrolein on Pt(111) and Pd(111) surfaces is investigated employing density functional theory calculations. The computed potential energy surfaces together with the analysis of reaction mechanisms demonstrate that steric effects are an important factor that governs chemoselectivity. The reactions at the C=O functionality require more space than the reactions at the C=C functionality. Therefore the formation of allyl alcohol is more favorable at low coverage, while the reduction of the C=C bond and the formation of propanal becomes kinetically more favorable at higher coverage. The elementary reaction steps are found to follow different reaction mechanisms, which are identified according to terminology typically used in organometallic catalysis. The transition state scaling (TSS) relationship is demonstrated and the origin of multiple TSS lines is linked to variation of an internal electronic structure of a carbon skeleton.     

纳米Pd和Au催化CO2还原粒径效应的密度泛函理论计算研究

以可再生能源为能量来源,在水溶液中进行的光(电)催化CO₂还原生成高附加值化学品和燃料是解决能源危机与环境污染的有效途径之一.CO是一种简单却很重要的CO₂还原产物,它可以作为水煤气变换反应与费托合成的重要原料.具有较高CO选择性的贵金属纳米颗粒催化剂(如Au和Pd)一直受到研究者的广泛关注.一般来说,金属颗粒催化剂的催化性能与粒径大小密切相关,即所谓的粒径效应.然而在实际的理论计算研究中,由于受到计算能力的限制,催化剂模型都仅局限于简单的周期性模型或小的金属团簇模型,无法准确描述真实颗粒上复杂的反应位点的性质,导致了对催化行为的误解.因此,建立更加真实的颗粒模型对探究纳米颗粒催化剂上活性位点的性质,解释其粒径效应至关重要.本文旨在阐述Au与Pd纳米颗粒催化剂不同活性位点上CO₂还原反应与产H2副反应的竞争机制,并解释Au与Pd纳米颗粒催化剂在CO₂电还原中表现出不同粒径效应的原因.本文基于密度泛函理论,采用VASP软件,BEEF-vdW泛函进行计算.分别建立了原子数为55,147,309和561的颗粒模型和高CO^*覆盖度模型,避免了传统周期性模型的局限性,探究了金属颗粒催化剂不同反应位点上的CO选择性.结果表明,对于颗粒模型来说,(100)位点对CO的选择性优于边缘位点;但对于周期性模型来说,Au(211)对CO的选择性则优于Au(100).产生这种反差的主要原因在于Au颗粒的边缘位点对H*的吸附过强.通过对比,我们直观地展现了颗粒模型上平面位点和Edge位点与相对应的周期性模型上CO选择性的区别,突出了模型选择对揭示活性位点性质的重要性.在此基础上,通过计算理论CO法拉第效率,发现Au颗粒随着粒径的减小,CO选择性降低,与实验的趋势一致.对于Pd催化剂来说,低覆盖度模型无法正确预测活性位点的性质;而高CO覆盖度的情况下,Pd颗粒的边缘位点对COOH^*吸附能更强,这是导致边缘位点上CO选择性更高的主要原因.同样通过计算理论CO法拉第效率,发现随着粒径的减小,Pd颗粒上CO选择性升高.本文不仅成功揭示了Au与Pd颗粒催化剂上活性位点的性质,对粒径效应做出了合理解释,也强调了合理的计算模型是理论研究的基础.     

Au/Pd(111)双金属表面催化噻吩加氢脱硫的反应机理

采用密度泛函理论(DFT)计算了Pd(111)表面含有N(N=1-4)个Au原子数目时的表面形成能,选取最优构型进一步研究了噻吩在Au/Pd(111)双金属表面的吸附模式及加氢脱硫反应过程.结果表明:当Pd(111)表面含有1个Au原子时,其形成能最低.在Au/Pd(111)双金属表面噻吩初始吸附于Pd-Hcp-30°位时,其构型最稳定.在各加氢脱硫过程中,反应总体均放出热量.对于直接脱硫机理,其所需活化能较低,但脱硫产物较难控制;对于间接脱硫机理,反应最有可能按照顺式加氢方式进行,C―S键断裂开环时所需活化能最高,是反应的限速步骤.此外,与单一Au(111)面及Pd(111)面相比,Au/Pd(111)双金属表面限速步骤的反应能垒最低,表明AuPd双金属催化剂比Au、Pd单金属催化剂更有利于噻吩加氢脱硫反应的进行.     

Au/Pd(111)双金属表面催化噻吩加氢脱硫的反应机理

采用密度泛函理论（DFT）计算了Pd（111）表面含有N（N=1-4）个Au原子数目时的表面形成能,选取最优构型进一步研究了噻吩在Au/Pd（111）双金属表面的吸附模式及加氢脱硫反应过程. 结果表明：当Pd（111）表面含有1个Au原子时,其形成能最低. 在Au/Pd（111）双金属表面噻吩初始吸附于Pd-Hcp-30°位时,其构型最稳定. 在各加氢脱硫过程中,反应总体均放出热量. 对于直接脱硫机理,其所需活化能较低,但脱硫产物较难控制;对于间接脱硫机理,反应最有可能按照顺式加氢方式进行,C―S键断裂开环时所需活化能最高,是反应的限速步骤. 此外,与单一Au（111）面及Pd（111）面相比,Au/Pd（111）双金属表面限速步骤的反应能垒最低,表明AuPd双金属催化剂比Au、Pd单金属催化剂更有利于噻吩加氢脱硫反应的进行.     

噻吩在M(111)(M=Pd,Pt,Au)表面的吸附(英文)

采用密度泛函理论(DFT),选取DMol3程序模块,对噻吩在M(111)(M=Pd,Pt,Au)表面上的吸附行为进行了探讨.通过对噻吩在不同底物金属上的吸附能、吸附构型、Mulliken电荷布居、差分电荷密度以及态密度的分析发现,噻吩在Pd(111)面上的吸附能最大,Pt(111)面次之,Au(111)面最小.吸附后,噻吩在Au(111)面上的构型几乎保持不变,最终通过S端倾斜吸附于top位;噻吩在Pd(111)及Pt(111)面上发生了折叠与变形,环中氢原子向上翘起,最终通过环平面平行吸附于hollow位.此外,噻吩环吸附后芳香性遭到了破坏,环中碳原子发生sp3杂化,同时电子逐渐由噻吩向M(111)面发生转移,M(111)面上的部分电子也反馈给了噻吩环中的空轨道,这种协同作用最终导致了噻吩分子稳定吸附于M(111)面.     

Two-dimensional Molecular Phase Transition of Alkylated-TDPB on Au(111) and Cu(111) Surfaces

The derivatives of aromatic cores bearing alkyl chains with different lengths are of potential interest in on-surface chemistry, and thus have been widely investigated both at liquid-solid interfaces and in vacuum. Here, we report on the structural evaluation of self-assembled 1,3,5-tri(4-dodecylphenyl)benzene(TDPB) molecules with increased molecular coverages on both Au(111) and Cu(111) surfaces. As observed on Au(111), rhombic and herringbone structures emerge successively depending on surface coverage. In the case of Cu(111), the same process of phase conversion is also observed, but with two distinct structures. In comparison, the self-assembled structures on Au(111) surface are packed more densely than that on Cu(111) surface under the same preparation conditions. This may fundamentally result from the higher adsorption energy of TDPB molecules on Cu(111), restricting their adjustment to optimize a thermodynamically favorable molecular packing.     

Rotationally inelastic scattering of HD from Cu(100) and Pd(111)

Rotational excitation of HD scattered from Cu(100), Pd(111), and Pd(111):H(D) was measured using molecular beam and quantum-state-specific laser spectroscopy techniques. Greater than 91% of the incident HD population was in the v = 0, J = 0 state. The final rotational distributions from Cu(100), Pd(111), and Pd(111):H(D) were compared for a HD beam at an incident energy of 74 meV. For all the three surfaces studied, rotationally inelastic scattering probabilities were large. We find that the final HD rotational distributions are remarkably similar for the three surfaces even though Pd(111) is very reactive to dissociative adsorption of HD whereas Cu(100) and Pd(111):H(D) are chemically inert.