Molecular ion emission from single large cluster impacts

We investigated the emission of the secondary ions stimulated by single impacts of 136 keV Au₄₀₀⁴⁺ projectiles. The study was carried out on targets of glycine, phenylalanine, and C₆₀. In addition, a target of C₆₀ was examined with 18 keV C₆₀⁺ projectiles. The experiments were performed in the event-by-event bombardment/detection mode. The secondary ions were identified with linear time-of-flight mass spectrometer equipped with an 8-anode detector. The Au₄₀₀⁴⁺ projectile induces abundant multi-ion emission, for instance the average number of detected ions (atomic, fragment, molecular and cluster ions) emitted per event from glycine target is 12.5. The glycine intact molecular ion (Gly⁻) yield is 1.14. The bombardment of a C₆₀ target results in the efficient emission of multiple intact C₆₀⁻ (total yield is 0.15).     

Polyethylene terephthalate (PET) bulk film analysis using C60, Au3, and Au primary ion beams

The damage characteristics of polyethylene terephthalate (PET) have been studied under bombardment by C₆₀⁺, Au₃⁺ and Au⁺ primary ions. The observed damage cross-sections for the three ion beams are not dramatically different. The secondary ion yields however were significantly enhanced by the polyatomic primary ions where the secondary ion yield of the [M + H]⁺ is on average 5× higher for C₆₀⁺ than Au₃⁺ and 8× higher for Au₃⁺ than Au⁺. Damage accumulates under Au⁺ and Au₃⁺ bombardment while C₆₀⁺ bombardment shows a lack of damage accumulation throughout the depth profile of the PET thick film up to an ion dose of ∼1 × 10¹⁵ ions cm⁻². These properties of C₆₀⁺ bombardment suggest that the primary ion will be a useful molecular depth profiling tool.     

Monoatomic and cluster beam effect on ToF-SIMS spectra of self-assembled monolayers on gold

Self-assembled monolayers represent well-defined systems that is a good model surface to study the effect of primary ion beams used in secondary ion mass spectrometry. The effect of polyatomic primary beams on both aliphatic and aromatic self-assembled monolayers has been studied. In particular, we analysed the variation of the relative secondary ion yield of both substrate metal-cluster (Au_n⁻) in comparison with the molecular ions (M⁻) and clusters (M_xAu_y⁻) by using Bi⁺, Bi₃⁺, Bi₅⁺ beams. Moreover, the differences in the secondary ion generation efficiency are discussed. The main effect of the cluster beams is related to an increased formation of low-mass fragments and to the enhancement of the substrate related gold-clusters. The results show that, at variance of many other cases, the static SIMS of self-assembled monolayers does not benefit of the use of polyatomic primary ions.     

Influence of primary ion species on the secondary cluster ion emission process from SAMs of hexadecanethiol on gold

In order to investigate the secondary cluster ion emission process of organo-metallic compounds under keV ion bombardment, self-assembled monolayers (SAMs) of alkanethiols on gold are ideal model systems. In this experimental study, we focussed on the influence of the primary ion species on the emission processes of gold-alkanethiolate cluster ions from a hexadecanethiol SAM on gold. For this purpose, we carried out time-of-flight secondary ion mass spectrometry (TOF-SIMS) measurements using the following primary ion species and acceleration voltages: Ar⁺, Xe⁺, SF₅⁺ (10 kV), Bi⁺, Bi₃⁺(25 kV), Bi₃²⁺, Bi₅²⁺, Bi₇²⁺ (25 kV).It is well known that molecular ions M⁻ and gold-alkanethiolate cluster ions Au_xM_y⁻ with M = S-(CH₂)₁₅-CH₃, x − 3 ≤ y ≤ x + 1, x, y > 0, show intense peaks in negative mass spectra. We derived yields Y_SI exemplarily for the molecular ions M⁻ and the gold-hexadecanethiolate cluster ions Au_y+1M_y⁻ up to y = 8 and found an exponentially decreasing behaviour for increasing y-values for the cluster ions.In contrast to the well-known increase in secondary ion yield for molecular secondary ions when moving from lighter to heavier (e.g. Ar⁺ to Xe⁺) or from monoatomic to polyatomic (e.g. Xe⁺ to SF₅⁺) primary ions, we find a distinctly different behaviour for the secondary cluster ions. For polyatomic primary ions, there is a decrease in secondary ion yield for the gold-hexadecanethiolate clusters whereas the relative decrease of the secondary ion yield ξ_Y with increasing y remains almost constant for all investigated primary ions.     

Comparison of secondary ion intensity enhancement from polymers on silicon and silver substrates by using Au-TOF-SIMS

The usefulness of the usage of cluster primary ion source together with an Ag substrate and detection of Ag cationized molecular ions was studied from the standpoint to realize high sensitivity TOF-SIMS analysis of organic materials. Although secondary ions from polymer thin films on a Si substrate can be detected in a higher sensitivity with Au₃⁺ cluster primary ion compared with Ga⁺ ion bombardment, it was clearly observed that the secondary ion intensities from samples on an Ag substrate showed quite a different tendency from that on Si. When monoatomic primary ions, e.g., Au⁺ and Ga⁺, were used for the measurement of the sample on an Ag substrate, [M+Ag]⁺ ions (M corresponds to polyethylene glycol molecule) were detected in a high sensitivity. On the contrary, when Au₃⁺ was used, no intensity enhancement of [M+Ag]⁺ ions was observed. The acceleration energy dependence of the detected secondary ions implies the different ionization mechanisms on the different substrates.     

Influence of massive projectile size and energy on secondary ion yields from organic surfaces

We investigated the influence of the projectile size and energy using Au_n^q+ clusters (5 < n < 400, 1 < q < 4) impacting on a glycine target with a 19q-34q keV energy range. We show that both CN⁻ fragment and Gly⁻ molecular ion yields are equivalent for projectiles with n > 9 and increase with the energy per projectile atoms. A maximum yield of 0.5 (50%) for both CN⁻ and Gly⁻ was obtained with the Au₄₀₀⁴⁺ projectile at 136 keV total energy. For Gly⁻, the yield enhancement is linear for Au_n when n > 5. Trends for the CN⁻ fragment are different. A nonlinear yield enhancement proportional to n³ is observed for Au_n when n < 9.     

Substrate effects on the analysis of biomolecular layers using Au, Au3 and C60 bombardments

Effects of platinum silicon, graphite and PET substrates on the secondary ion yield of sub-monolayer and multilayer samples of Cyclosporin A following 20 keV Au⁺, Au₃⁺and C₆₀⁺ impacts have been investigated. The obtained results of sub-monolayer samples show that platinum enhances the yield of the pseudo-molecular ion following Au⁺ and Au₃⁺ impacts due to the high density of the substrate that enables the energy of the primary ions to be deposited near the surface. C₆₀⁺ impacts on sub-monolayer samples are less effective, but there is an enhancement on PET substrates. Impacts of 20 keV Au⁺ and Au₃⁺ are not very efficient on multilayer samples. 20 keV C₆₀⁺ impacts enhance the yields significantly, especially for the relatively high molecular weight [M+H]⁺ ion.     

Luminescence studies on swift heavy ion irradiated nanocrystalline aluminum oxide

Pellets of nanocrystalline aluminum oxide synthesized by a combustion technique are irradiated with 120 MeV Au⁹⁺ ions for fluence in the range 5×10¹¹-1×10¹³ ions cm⁻². Two photoluminescence (PL) emissions, a prominent one with peak at ∼525 nm and a shoulder at ∼465 nm are observed in heat treated and Au⁹⁺ ion irradiated aluminum oxide. The 525 nm emission is attributed to F₂²⁺-centers. The PL intensity at 525 nm is found to increase with increase in ion fluence up to 1×10¹² ions cm⁻² and decreases beyond this fluence. Thermoluminescence (TL) of heat-treated and swift heavy ion (SHI) irradiated aluminum oxide gives a strong and broad TL glow with peak at ∼610 K along with a weak shoulder at 500 K. The TL intensity is found to increase with Au⁹⁺ ion fluence up to 1×10¹³ ions cm⁻² and decreases beyond this fluence.     

Thiolated cyclodextrin self-assembled monolayer-like characterized with secondary ion mass spectrometry

In the work the focus is on the preparation of self-assembled monolayer-like films consisting of thiolated cyclodextrin on gold substrate and a characterization by using secondary ion mass spectrometry. The short (1 min) and long (1 h) time preparations of self-assembled monolayer-like films, resulting in submonolayer and monolayer regimes, are investigated, respectively. The observed species of thiolated cyclodextrin (M as molecular ion) self-assembled monolayer-like films are assigned to three groups: Au_xH_yS_z clusters, fragments with origin in cyclodextrin molecule associated with Au, and molecular ions. The group of Au_xH_yS_z (x = 2-17, y = 0-2, z = 1-5) clusters have higher intensities than other species in the positive and even more in negative mass spectra. Interestingly, the dependence between the number of Au and S atoms shows that with the increasing size of Au_xH_yS_z clusters up to 11 Au atoms, the number of associated S atoms is also increasing and then decreasing. Molecular species as (M−S+H)Na⁺, (M+H)Na⁺, AuMNa⁺, (M₂−S)Na⁺, and M₂Na⁺ are determined, and also in cationized forms with K⁺. The intensities of thiolated cyclodextrin fragments at the long time preparation are approximately 10 times higher than the intensities of the same fragments observed at the short time. The largest observed ions in thiolated cyclodextrin self-assembled monolayer-like films are AuM₂ and Au₂M. The thiolated cyclodextrin molecular ions are compared with hexadecanethiol molecular ions in the form of Au_xM_w where the values of x and w are smaller for thiolated cyclodextrin than for hexadecanethiol. This result is supported with larger, more compact, and more stabile thiolated cyclodextrin molecule.     

Recombination measurements at low energies with Au49+,50+,51+ at the TSR

Recombination of Au⁴⁹⁺, Au⁵⁰⁺, and Au⁵¹⁺ ions has been studied at the TSR. With Au⁵⁰⁺ ions a storage lifetime of only 2 to 4 s was observed with the magnetically expanded electron beam of the cooler at a density of n_e = 10⁷ cm^-3. This short storage time is a consequence of the highest recombination rate coefficient ever observed with an atomic ion (1.8·10^-6 cm³ s^-1 at zero relative energy E_rel = 0 between electrons and ions). At about 30 meV a huge dielectronic recombination resonance is found with a record small width of only about 15 meV. Such resonances fortuitously occurring near E_rel=0 are probably the main reason for the enhanced recombination rates observed with Au⁵⁰⁺, with Pb⁵³⁺ (in a recent experiment at LEAR) as well as with other complex ions. For Au⁴⁹⁺ and Au⁵¹⁺ the recombination rates are smaller by an order of magnitude. This revised version was published online in August 2006 with corrections to the Cover Date.     

Metallophilic Bond‐Induced Quenching of Delayed Fluorescence in Au25@BSA Nanoclusters

The metallophilic bond is a weak interaction between closed‐shell ions and has been widely used a probe for various sensing of toxic chemicals for environmental safety concerns. Here, the interaction between Au nanoclusters (NCs) and metallic ions (mercury (Hg²⁺) and copper (Cu²⁺) ions) is explored using steady‐state and time‐resolved luminescence and transient absorption measurements. For Hg²⁺ ions, the delayed fluorescence (DF) of bovine serum albumin (BSA) protected Au₂₅ (Au₂₅@BSA) NCs is quenched via an effective triplet state electron transfer through the metallophilic bond. However, the Cu²⁺ ions do not alter the DF in Au₂₅@BSA NCs because of the absence of the metallophilic interaction. Furthermore, for Au₈@BSA and Au₁₀@histidine, in which there are no Au⁺ ions on the surface, the fluorescence is not quenched by Hg²⁺ ions. Such a novel triplet electron transfer process through metallophilic bonds are observed and reported for the first time. The reduction of the reverse intersystem crossing is the crucial for Hg²⁺ ion sensing in the fluorescent Au₂₅@BSA NCs.     

Characterisation of human hair surfaces by means of static ToF-SIMS: A comparison between Ga and C60 primary ions

This study deals with the secondary ion yield improvement induced by using C₆₀⁺ primary ions instead of Ga⁺ ones to characterize human hair surfaces by ToF-SIMS. For that purpose, a bunch of hair fibres has been analysed with both ion sources. A high improvement is observed for the detection of amino acids with C₆₀⁺ primary ions as compared to Ga⁺ ions. As an example, a yield enhancement factor greater than 3000 is found for the CNO⁻ peak. A similar gain is observed for the positive secondary ions characteristic of the amino acids. Most of the atomic ions, such as Ca⁺, O⁻ and S⁻, constitute minor peaks with C₆₀⁺ ions while they often dominate the spectrum in the case of Ga⁺ ions. However, with the C₆₀⁺ source, a series of inorganic combination peaks with the elements Ca, S and O are observed in the positive spectra (i.e. HCaSO₄⁺), while they are marginal with the Ga⁺ source. For the mass range beyond 100 m/z and in both polarities, the hair fingerprints are similar with both sources. In average, for a comparable number of primary ions per spectrum, the C₆₀⁺ ion source gives intensities between two and three orders of magnitude higher than the Ga⁺ one.     

Analysis of TOF-SIMS spectra from fullerene compounds

We analyzed TOF-SIMS spectra obtained from three different size of fullerenes (C₆₀, C₇₀ and C₈₄) by using Ga⁺, Au⁺ and Au₃⁺ primary ion beams and investigated the fragmentation patterns, the enhancement of secondary ion yields and the restraint of fragmentation by using cluster primary ion beams compared with monoatomic primary ion beams. In the TOS-SIMS spectra from C₇₀ and C₈₄, it was found that a fragment ion, identified as C₆₀⁺ (m/z = 720), showed a relatively high intensity compared with that of other fragment ions related to C₂ depletion. It was also found that the Au₃⁺ bombardment caused intensity enhancement of intact molecules (C₆₀⁺, C₇₀⁺ and C₈₄⁺) and restrained the fragmentation due to C₂ depletion.     

Nanowires with well defined radii formed in operating liquid metal ion sources (LMIS)

For some elements such as germanium or tin, the mass spectra of ions emitted by liquid metal ion sources (LMIS) exhibit periodicities, i.e. series of equidistant peaks with an increase, ν, in the number of atoms between two peaks. We attribute it to the existence of jets in operating LMIS, the upper part of them being cylinders with ν-atom sections. The Ge_6m+1³⁺ and Sn_6m+1³⁺, m=3 to 8, and Ge_6m+4³⁺, m= 9 to 14, observed ions can be explained by this mechanism, here ν=6. We extend this mechanism to bismuth and gold and, in this last case, it allows the interpretation of a yet unexplained Au₈³⁺ ion.     

Dependence of critical pitting temperature on the concentration of sulphate ion in chloride-containing solutions

Effects of varying concentration of sulphate (SO₄²⁻) ion on the pitting behavior of 316SS have been investigated using potentiostatic critical pitting temperature (CPT) measurements, potentiostatic current transient technique and scanning electron microscopy in NaCl solution containing 0.5% Cl⁻ ions. The results demonstrated that when the concentration of SO₄²⁻ ion is less than 0.42%, the CPT is surprisingly lower than that without SO₄²⁻ ion, showing an accelerating effect of the SO₄²⁻ ion on pit initiation, which is different from the traditional concept. As the concentration of SO₄²⁻ ion increases beyond 0.42%, the CPT is higher than that without SO₄²⁻ ion, displaying an inhibiting effect of the SO₄²⁻ ion on pit initiation. Based on the above results, a qualitative model is proposed to explain the inhibiting and accelerating effect of SO₄²⁻ ion on the pit initiation using the mechanism of ions-competitive adsorption between SO₄²⁻ and Cl⁻ ions. The electric charges calculated in the process of pitting corrosion indicated that the pit morphology and its dimension are dependent on the content of SO₄²⁻ ion in chloride-containing solutions. The higher the concentration of SO₄²⁻ ion, the larger the dimension of the pit, reflecting an accelerating effect on pit growth.     

Au5+ ion implantation induced structural phase transitions probed through structural,microstructural and phonon properties in BiFeO3 ceramics,using synergistic ion beam energy

Implanted Au⁵⁺-ion-induced modification in structural and phonon properties of phase pure BiFeO₃ (BFO) ceramics prepared by sol–gel method was investigated. These BFO samples were implanted by 15.8?MeV ions of Au⁵⁺ at various ion fluence ranging from 1?×?10¹⁴ to 5?×?10¹⁵?ions/cm². Effect of Au⁵⁺ ions’ implantation is explained in terms of structural phase transition coupled with amorphization/recrystallization due to ion implantation probed through XRD, SEM, EDX and Raman spectroscopy. XRD patterns show broad diffuse contributions due to amorphization in implanted samples. SEM images show grains collapsing and mounds’ formation over the surface due to mass transport. The peaks of the Raman spectra were broadened and also the peak intensities were decreased for the samples irradiated with 15.8?MeV Au⁵⁺ ions at a fluence of 5?×?10¹⁵?ion/cm². The percentage increase/decrease in amorphization and recrystallization has been estimated from Raman and XRD data, which support the synergistic effects being operative due to comparable nuclear and electronic energy losses at 15.8?MeV Au⁵⁺ ion implantation. Effect of thermal treatment on implanted samples is also probed and discussed.     

Crystal structure and photoluminescence of (Y1−xCex)2Si3O3N4

Oxonitridosilicate phosphors with compositions of (Y_1−xCe_x)₂Si₃O₃N₄ (x=0−0.2) have been synthesized by solid state reaction method. The structures and photoluminescence properties have been investigated. Ce³⁺ ions have substituted for Y³⁺ ions in the lattice. The emission and excitation spectra of these phosphors show the characteristic photoluminescence spectra of Ce³⁺ ions. Based on the analyses of the diffuse reflection spectra and the PL spectra, a systematic energy diagram of Ce³⁺ ion in the forbidden band of sample with x=0.02 is given. The best doping Ce content in these phosphors is ∼2 mol%. The quenching temperature is ∼405 K for the 2 mol% Ce content sample. The luminescence decay properties were investigated. The primary studies indicate that these phosphors are potential candidates for application in three-phosphor-converted white LEDs.     

Ion-beam induced mixing of Cu/Au bilayer thin film (kinematics and formation of solid solutions)

Ion-beam induced atomic mixing of Cu/Au bilayer thin film is studied using combined electrical resistivity measurements and Rutherford Backscattering Spectrometry (RBS). 400 keV Kr⁺ ion irradiation with fluences ranging from 3.3×10¹⁵ to 7.6×10¹⁶ ions/cm² at room temperature have been used. Ion beam mixing lead to a uniformly mixed metal alloy. The formation of Cu/Au solid solutions depends on the initial composition and on the fluence of irradiating ions. For an initial composition of Cu₄₂Au₅₈, a Cu-rich solid solution of composition Cu₇₂Au₂₈ is formed after irradiation with 7.6×10¹⁶ ions/cm². The kinematics of the intermixing process is also studied by in situ electrical resistivity measurements which confirmed the formation of the Cu/Au solid solutions.     

Shape and size transformation of gold nanorods (GNRs) via oxidation process: A reverse growth mechanism

The anisotropic shape transformation of gold nanorods (GNRs) with H₂O₂ was observed in the presence of “cethyl trimethylammonium bromide” (CTAB). The adequate oxidative dissolution of GNR is provided by the following autocatalytic scheme with H₂O₂: Au⁰ → Au⁺, Au⁰ + Auⁿ⁺ → 2Au³⁺, n = 1 and 3. The shape transformation of the GNRs was investigated by UV-vis spectroscopy and transmission electron microscopy (TEM). As-synthesised GNRs exhibit transverse plasmon band (TPB) at 523 nm and longitudinal plasmon band (LPB) at 731 nm. Upon H₂O₂ oxidation, the LPB showed a systematic hypsochromic (blue) shift, while TPB stays at ca. 523 nm. In addition, a new emerging peak observed at ca. 390 nm due to Au(III)-CTAB complex formation during the oxidation. TEM analysis of as-synthesised GNRs with H₂O₂ confirmed the shape transformation to spherical particles with 10 nm size in 2 h, whereas centrifuged nanorod solution showed no changes in the aspect ratio under the same condition. Au³⁺ ions produced from oxidation, complex with excess free CTAB and approach the nanorods preferentially at the end, leading to spatially directed oxidation. This work provides some information to the crystal stability and the growth mechanism of GNRs, as both growth and shortening reactions occur preferentially at the edge of single-crystalline GNRs, all directed by Br⁻ ions.     

Variable temperature EPR spectra of Copper (II) ions in kainite crystals

X-band electron paramagnetic resonance (EPR) studies on divalent copper ions embedded in KMgClSO₄·3H₂O single crystals have been performed at low temperature (123 K). The angular variation of the EPR spectra reveals the presence of two Cu²⁺ sites, which have different orientations. The spin-Hamiltonian parameters of this six-coordinated cupric ion have been evaluated from the EPR spectra at 123 K. The forbidden lines due to Δm_I=±1 transitions are observed in between allowed transitions. The temperature variation EPR studies have also been performed both for a single crystal and a polycrystalline sample. The ground state wavefunction of Cu²⁺ ions has been estimated and is found to be an admixture of d_3z²−r² and d_x²−y². The temperature variation of the EPR spectra reveals that Cu²⁺ ions exhibit dynamic Jahn-Teller effect. From the polycrystalline EPR data, the temperature dependent magnetic susceptibilities are evaluated and discussed.