Electrospun cellulose acetate fibers: effect of solvent system on morphology and fiber diameter

This paper reports an investigation of the effects of solvent system, solution concentration, and applied electrostatic field strength (EFS) on the morphological appearance and/or size of as-spun cellulose acetate (CA) products. The single-solvent systems were acetone, chloroform, N,N -dimethylformamide (DMF), dichloromethane (DCM), methanol (MeOH), formic acid, and pyridine. The mixed-solvent systems were acetone–DMAc, chloroform–MeOH, and DCM–MeOH. Chloroform, DMF, DCM, MeOH, formic acid, and pyridine were able to dissolve CA, forming clear solutions (at 5% w/v), but electrospinning of these solutions produced mainly discrete beads. In contrast, electrospinning of the solution of CA in acetone produced short and beaded fibers. At the same solution concentration of 5% (w/v) electrospinning of the CA solutions was improved by addition of MeOH to either chloroform or DCM. For all the solvent systems investigated smooth fibers were obtained from 16% (w/v) CA solutions in 1:1, 2:1, and 3:1 (v/v) acetone–DMAc, 14–20% (w/v) CA solutions in 2:1 (v/v) acetone–DMAc, and 8–12% (w/v) CA solutions in 4:1 (v/v) DCM–MeOH. For the as-spun fibers from CA solutions in acetone–DMAc the average diameter ranged between 0.14 and 0.37 μm whereas for the fibers from solutions in DCM–MeOH it ranged between 0.48 and 1.58 μm. After submersion in distilled water for 24 h the as-spun CA fibers swelled appreciably (i.e. from 620 to 1110%) but the physical integrity of the fibrous structure remained intact.     

LC–ESI–MS for Rapid and Sensitive Determination of Aripiprazole in Human Plasma

A rapid, sensitive, and accurate high-performance liquid-chromatographic–mass spectrometric (HPLC–MS) method, with estazolam as internal standard, has been developed and validated for determination of aripiprazole in human plasma. After liquid–liquid extraction the compound was analyzed by HPLC on a C₁₈ column, with acetonitrile—30 mm ammonium acetate containing 0.1% formic acid, 58:42 (v/v), as mobile phase, coupled with electrospray ionization mass spectrometry (ESI-MS). The protonated analyte was quantified by selected-ion recording (SIR) with a quadrupole mass spectrometer in positive-ion mode. Calibration plots were linear over the concentration range 19.9–1119.6 ng mL⁻¹. Intra-day and inter-day precision (CV%) and accuracy (RE%) for quality-control samples (37.3, 124.4, and 622.0 ng mL⁻¹) ranged between 2.5 and 9.0% and between 1.3 and 3.5%, respectively. Extraction recovery of aripiprazole from plasma was in the range 75.8–84.1%. The method enables rapid, sensitive, precise, and accurate measurement of the concentration of aripiprazole in human plasma.     

HPTLC–densitometric and HPTLC–MS methods for analysis of flavonoids

HPTLC silica gel plates without and with fluorescence indicator F₂₅₄ in combination with n-hexane–ethyl acetate–formic acid (20:19:1, v/v/v) as a developing solvent were explored for the HPTLC–densitometric and HPTLC–MS/(MSⁿ) analyses of flavonoids. Pre-development of the plates with chloroform–methanol (1:1, v/v) was needed for reliable HPTLC–densitometric analyses of flavonoid aglycones in the whole R_F range, while 2-step pre-development (1^st methanol–formic acid (10:1, v/v), 2^nd methanol), that decreased background signals of formic acid adducts, was required for HPTLC–MS analyses. Optimization with conditioning of the adsorbent layer with water before development and saturation of the twin trough chamber resulted in required decrease of the R_F values of studied flavonoids (flavone, apigenin, luteolin, chrysin, quercetin dihydrate, myricetin, kaempferide, kaempferol, naringenin, pinocembrin).

Detection was performed based on fluorescence quenching (on the plates with F₂₅₄), natural fluorescence and after post-chromatographic derivatization with natural product reagent without or with further enhancement and stabilization of fluorescent zones with polyethylene glycol (PEG 400 or PEG 4000) or paraffin–n-hexane reagents. For all three reagents, drying temperature and time passed after drying influenced the intensity, which was increasing the first 20?min, and the stability (less than 2?h for PEGs and at least 24?h for paraffin–n-hexane) of the standards’ zones.

Optimal wavelengths for densitometric evaluation were selected based on in-situ absorption spectra scanned before and after derivatization and after stabilization. The developed method was tested via analyses of propolis, roasted coffee, rose hip, hibiscus, rosemary and sage crude extracts. To further increase the reliability of the obtained densitometric results HPTLC–MS/(MSⁿ) analyses of all crude extracts were performed. Several phenolic and non-phenolic compounds were tentatively identified.

Some possible interferences with phenolic acids (chlorogenic acid, rosmarinic acid, protocatechuic acid, gallic acid, syringic acid, ellagic acid, trans-cinnamic acid, o-coumaric acid, m-coumaric acid, p-coumaric acid, caffeic acid, ferulic acid, sinapic acid) that are often present in the extracts together with flavonoids were also examined.     

Stability Indicating HPTLC and LC Determination of Dasatinib in Pharmaceutical Dosage Form

Two sensitive and reproducible methods are described for the quantitative determination of dasatinib in the presence of its degradation products. The first method was based on high performance thin layer chromatography (HPTLC) followed by densitometric measurements of their spots at 280 nm. The separation was on HPTLC aluminium sheets of silica gel 60 F₂₅₄ using toluene:chloroform (7.0:3.0, v/v). This system was found to give compact spots for dasatinib after development (R _F value of 0.23 ± 0.02). The second method was based on high performance liquid chromatography (HPLC) of the drug from its degradation products on reversed phase, PerfectSil column [C₁₈ (5 μm, 25 cm × 4.6 mm, i.d.)] at ambient temperature using mobile phase consisting of methanol:20 mM ammonium acetate with acetic acid (45:55, v/v) pH 3.0 and retention time (t _R = 8.23 ± 0.02 min). Both separation methods were validated as per the ICH guidelines. No chromatographic interference from the tablet excipients was found. Dasatinib was subjected to acid–alkali hydrolysis, oxidation, dry heat, wet heat and photo-degradation. The drug was susceptible to acid–alkali hydrolysis and oxidation. The drug was found to be stable in neutral, wet heat, dry heat and photo-degradation conditions. As the proposed analytical methods could effectively separate the drug from its degradation products, they can be employed as stability indicating.     

Validated HPLC and HPTLC Method for Simultaneous Quantitation of Amlodipine Besylate and Olmesartan Medoxomil in Bulk Drug and Formulation

Two methods are described for simultaneous determination of amlodipine besylate and olmesartan medoxomil in formulation. The first method was based on the HPTLC separation of two drugs on Merck HPTLC aluminium sheets of silica gel 60 F₂₅₄ using n-butanol: acetic acid: water (5:1:0.1, v/v/v) as the mobile phase. The second method was based on the HPLC separation of the two drugs on the RP-PerfectSil-100 ODS-3–C₁₈ column from MZ-Analysetechnik GmbH, Germany and acetonitrile/0.03 M ammonium acetate buffer (pH = 3) in a ratio of 55:45 as the mobile phase. Both methods have been applied to formulation without interference of excipients of formulation.     

Simultaneous determination of harpagoside and cinnamic acid in rat plasma by high-performance liquid chromatography: application to a pharmacokinetic study

Radix Scrophulariae (Xuanshen) is one of the famous Chinese herbal medicines widely used to treat rheumatism, tussis, pharyngalgia, arthritis, constipation, and conjunctival congestion. Harpagoside and cinnamic acid are the main bioactive components of Xuanshen. The purpose of this study was to develop an HPLC–UV method for simultaneous determination of harpagoside and cinnamic acid in rat plasma and investigate pharmacokinetic parameters of harpagoside and cinnamic acid after oral administration of Xuanshen extract (760 mg kg⁻¹). After addition of syringin as internal standard, the analytes were isolated from plasma by liquid–liquid extraction. Separation was achieved on a Kromasil C₁₈ column, and detection was by UV absorption at 272 nm. The described assay was validated in terms of linearity, accuracy, precision, recovery, and limit of quantification according to the FDA validation guidelines. Calibration curves for both analytes were linear with the coefficient of variation (r) for both was greater than 0.999. Accuracy for harpagoside and cinnamic acid ranged from 100.7–103.5% and 96.9–102.9%, respectively, and precision for both analytes were less than 8.5%. The main pharmacokinetic parameters found for harpagoside and cinnamic acid after oral infusion of Xuanshen extract were as follows: C _max 1488.7 ± 205.9 and 556.8 ± 94.2 ng mL⁻¹, T _max 2.09 ± 0.31 and (1.48 ± 0.14 h, AUC_0–24 10336.4 ± 1426.8 and 3653.1 ± 456.4 ng h mL⁻¹, 11276.8 ± 1321.4 and 3704.5 ± 398.8 ng h mL⁻¹, and t _1/2 4.9 ± 1.3 and 2.5 ± 0.9 h, respectively. These results indicated that the proposed method is simple, selective, and feasible for pharmacokinetic study of Radix Scrophulariae extract in rats. Figure Radix Scrophulariae     

Quantitative HPLC Determination and Stability Studies of Pyridostemin in Extracts and Water Dispersible Granule Formulations of Stemona curtisii

A reversed-phase high-performance liquid chromatographic method has been developed and validated for the determination of pyridostemin, the major pesticidal alkaloid found in Stemona curtisii. This methodology was applied to the investigation of plant extracts and water dispersible granule formulations. Stability indicating procedures have also been carried out. The chromatographic separation was on a C₁₈ column with a mixture of acetonitrile–water–triethylamine (30:70:0.12, v/v/v), using UV detection at 300 nm. Validation procedures showed that the method was specific, accurate and precise. The response was linear over a range of 5–25 μg mL⁻¹ with recoveries in the range of 98.28–102.85%. The RSD for intra- and inter-day precision were <0.72 and <1.29%, respectively. Extraction of plant material with dichloromethane gave a significantly higher pyridostemin content in the crude extracts when compared with extractions in methanol. Partial purification of the crude extracts by silica gel column chromatography was used to concentrate the mixture about fourfold. Degradation behavior of pyridostemin in the partially purified extracts followed first-order kinetics. The main pathways for its decomposition were base hydrolysis and oxidation.     

Simultaneous RP-LC Determination of Losartan Potassium, Ramipril, and Hydrochlorothiazide in Pharmaceutical Preparations

A simple, rapid, and precise reversed-phase high-performance liquid chromatographic method has been developed for simultaneous determination of losartan potassium, ramipril, and hydrochlorothiazide. The three drugs were separated on a 150 mm × 4.6 mm i.d., 5 μm particle, Cosmosil C₁₈ column. The mobile phase was 0.025 m sodium perchlorate–acetonitrile, 62:38 (v/v), containing 0.1% heptanesulphonic acid, pH adjusted to 2.85 with orthophosphoric acid, at a flow rate of 1.0 mL min⁻¹. UV detection was performed at 215 nm. The method was validated for linearity, accuracy, precision, and limit of quantitation. Linearity, accuracy, and precision were acceptable in the ranges 35–65 μg mL⁻¹ for losartan, 1.75–3.25 μg mL⁻¹ for ramipril, and 8.75–16.25 μg mL⁻¹ for hydrochlorothiazide.     

Determination of Apigenin by LC with Electrochemical Detection

A rapid, sensitive, and specific method for quantification of olmesartan, the prodrug of olmesartan medoxomil, in human plasma, using zidovudine as internal standard, is described. Sample preparation involved a simple solid-phase extraction procedure. The extract was analyzed by high-performance liquid chromatography coupled to electrospray tandem mass spectrometry (LC–MS–MS). Chromatography was performed isocratically on a 5 μm C₁₈ analytical column (50 mm × 4.6 mm i.d.) with water–acetonitrile–formic acid 20:80:0.1 (v/v) as mobile phase. The response to olmesartan was a linear function of concentration over the range 4.82–1,928 ng mL⁻¹. The lower limit of quantification in plasma was 4.82 ng mL⁻¹. The method was successfully applied in a bioequivalence study of an olmesartan formulation after administration as a single oral dose.     

Stability-Indicating HPTLC Method for Simultaneous Determination of Ezetimibe and Simvastatin

Simvastatin and ezetimibe are used to treat hyperlipidemia. A simple, selective and stability-indicating HPTLC method has been established for analysis of simvastatin and ezetimibe. The method has been validated so that both drugs can routinely be analyzed simultaneously. The method uses aluminum-backed silica gel 60F₂₅₄ TLC plates as stationary phase with n-hexane–acetone 6:4 (v/v) as mobile phase. Densitometric analysis of both drugs was carried out in absorbance mode at 234 nm. This system was found to give compact bands for simvastatin and ezetimibe (R _F 0.39 ± 0.05 and 0.50 ± 0.05, respectively). Linear relationships were obtained between response and amount of drug in the range 200–1,600 ng per band with high correlation coefficients (r ² = 0.9917 ± 0.0018 for simvastatin and r ² = 0.9927 ± 0.0021 for ezetimibe). The method was validated for precision, robustness, and recovery. The limits of detection and quantitation were 25 and 150 ng per band, respectively. Simvastatin and ezetimibe were subjected degradation by acid, pH 6.8 phosphate buffer, oxidation, dry heat, and wet heat. The degradation products were well resolved from the pure drug with significantly different R _F values. Because the method could effectively separate the drug from its degradation products, it can be used for stability-indicating analysis.     

Pathways of the reaction of nucleophilic addition of ammonia to formaldehyde in the gas phase and in the complex with formic acid:ab initio calculations

The gradient pathways of the reaction of nucleophilic addition of ammonia to formaldehyde were calculated for free molecules and in the NH₃...H₂CO...HC(O)OH complex by theab initio RHF/6-31G^**, MP2(fc)/6-31G^**, and MP2(full)/6-311++G^** methods. Both reactions proceed concertedly. In the first case, the reaction successively passes through two transitional states with an energy barrier exceeding 35 kcal mol⁻¹. In the case of the complex with formic acid, the reaction follows a conventional pathway, although its activation barrier calculated by the RHF/6-31G^** and MP2(fc)/6-31G^** methods decreases to 12.6 and 3.8 kcal mol⁻¹, respectively. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 1, pp. 13–20, January, 1998.     

UV light‐mediated alkylation of inorganic selenium

In the presence of low molecular weight organic acids (formic, acetic, propionic and malonic), inorganic selenium(IV) is converted by UV irradiation to volatile selenium carbonyl, dimethylselenide and diethylselenide, depending on the acid used. Gas chromatography–mass spectrometry analysis of the volatile products shows that, in 0.7 M formic acid solution, approximately 60–70% (v/v) SeH₂ and 30–40% (v/v) SeCO are formed. The presence of nitrate ion appears to increase threefold the formation of SeCO while completely suppressing formation of SeH₂. Copyright © 2003 Crown in the right of Canada. Published by John Wiley & Sons, Ltd.     

LC–MS for Identification and Elucidation of the Structure of In-Vivo and In-Vitro Metabolites of Atropine

In-vivo and in-vitro metabolism of atropine has been investigated by use of a highly specific and sensitive LC–MS ⁿ method. Feces, urine, and plasma samples were collected separately after ingestion of 25 mg kg⁻¹ atropine by healthy rats. Rat feces and urine samples were cleaned by liquid–liquid extraction and by solid-phase extraction (on C₁₈ cartridges), respectively. Methanol was added to rat plasma samples to precipitate plasma proteins. Atropine was incubated, in vitro, with homogenized liver and with intestinal flora from rats. The metabolites in the incubation solution were extracted with ethyl acetate. These pretreated samples were then analyzed by reversed-phase high-performance liquid chromatography on a C₁₈ column with methanol–ammonium acetate (2 mm, adjusted to pH 3.5 with formic acid), 70:30 (v/v), as mobile phase. Detection was by on-line MS ⁿ . Identification and elucidation of the structure of the metabolites were achieved by comparing molecular mass (ΔM), retention-times, and full-scan MS ⁿ spectra with those of the parent drug. Ten new metabolites (aponoratropine, apoatropine, hydroxymethoxyatropine, trihydroxyatropine, dimethoxyatropine, dihydroxymethoxyatropine, hydroxydimethoxyatropine, trihydroxymethoxyatropine, dihydroxydimethoxyatropine, and tropic acid) were identified in rat urine after ingestion of atropine. Nine metabolites (nortropine, tropine, aponoratropine, apoatropine, noratropine, hydroxyatropine, hydroxyatropine N-oxide, hydroxymethoxyatropine, and tropic acid) and the parent drug were detected in rat feces. Five metabolites (nortropine, tropine, tropic acid, apoatropine, and hydroxyatropine) and the parent drug were detected in rat plasma. Only two metabolites (apoatropine and noratropine) were detected in the homogenized liver incubation mixture. The hydrolyzed metabolites (tropine and tropic acid) and dehydrated metabolite apoatropine were found in the rat intestinal flora incubation mixture.     

A new kinetic model of photocatalytic degradation of formic acid in UV/TiO2 suspension system with in-situ monitoring

The results show that a newly developed kinetic model can successfully explain the photocatalytic kinetics of formic acid in UV/TiO₂ suspension system with in-situ monitoring and the apparent rate constant (k) is affected by the initial concentrations of formic acid, amounts of TiO₂, UV intensity and pH.     

Development and validation of HPTLC and green HPLC methods for determination of furosemide,spironolactone and canrenone,in pure forms,tablets and spiked human plasma

Two selective and accurate chromatographic methods are presented for simultaneous quantitation of spironolactone (SP) and furosemide (FR) and canrenone (CN), the main degradation product and the main active metabolite of SP. Method A was HPTLC, where separation was completed on silica gel HPTLC F₂₅₄ plates using ethyl acetate–triethylamine–acetic acid (9:0.7:0.5, by volume) as a developing system and UV detection at 254 nm. Method B was a green isocratic RP‐HPLC utilizing a C₁₈ (4.6 × 100 mm) column, the mobile phase consisting of ethanol–deionized water (45: 55, v/v) and UV estimation at 254 nm. Adjustment of flow rate at 1 mL/min and pH at 3.5 with glacial acetic acid was done. Regarding the greenness profile, the proposed RP‐HPLC method is greener than the reported one. ICH guidelines were followed to validate the developed methods. Successful applications of the developed methods were revealed by simultaneous determination of FR, SP and CN in pure forms and plasma samples in the ranges of 0.2–2, 0.05–2.6 and 0.05–2 μg/band for method A and 5–60, 2–60 and 2–60 μg/mL for method B for FR, SP and CN, respectively.     

Simultaneous HPTLC Determination of Escitalopram Oxalate and Clonazepam in Combined Tablets

A new, simple high-performance thin-layer chromatographic method has been established and validated for simultaneous determination of escitalopram oxalate and clonazepam in a combined tablet dosage form. The drugs were separated on aluminum plates precoated with silica gel 60 F₂₅₄; toluene–ethyl acetate–triethylamine 7:3.5:3 (v/v) was used as mobile phase. Quantitative analysis was performed by densitometric scanning at 258 nm. The method was validated for linearity, accuracy, precision, and robustness. The calibration plot was linear over the ranges 250–2,500 and 50–500 ng band⁻¹ for escitalopram oxalate and clonazepam, respectively. The method was successfully applied to the analysis of drugs in a pharmaceutical formulation.     

Determination of (E)-3,5,4′-Trimethoxystilbene in Rat Plasma by LC with ESI-MS

(E)-3,5,4′-trimethoxystilbene (BTM-0512) is a resveratrol analog with a variety of pharmacological action, including anti-cancer properties, anti-allergic activity, estrogenic activity, antiangiogenic activity, and vascular-targeting activity against microtubule-destabilization. There is, however, no validated analytical method for quantification of (E)-3,5,4′-trimethoxystilbene in biological matrices, so pharmacokinetic data and suitable methods for determination of the compound in plasma are currently lacking. A rapid and sensitive liquid chromatographic–mass spectrometric method for determination of (E)-3,5,4′-trimethoxystilbene in rat plasma, using carbamazepine as internal standard, has been developed and validated. Plasma samples were treated with acetonitrile to precipitate proteins. Samples were then analyzed by HPLC on a 250mm × 4.6 mm i.d., 5-μm particle, C₁₈ column with methanol–water, 80:20 (v/v), containing 10 mm ammonium acetate and 0.2% formic acid (pH 3.0), as mobile phase, delivered at 0.85 mL min⁻¹. A single-quadrupole mass spectrometer with an electrospray interface operated in selected-ion monitoring mode was used to detect [M + H]⁺ ions at m/z 271.3 for (E)-3,5,4′-trimethoxystilbene and m/z 237.5 for the internal standard. (E)-3,5,4′-trimethoxystilbene and the internal standard eluted as sharp, symmetrical peaks with retention times of 8.9 and 4 min, respectively. Calibration plots for (E)-3,5,4′-trimethoxystilbene in rat plasma at concentrations ranging from 0.01 to 5.0 μg mL⁻¹ were highly linear. Intra-day and inter-day precision, as RSD, was <12.9%, and accuracy was in the range 94.8–104.7%. The limit of detection in plasma was 0.005 μg mL⁻¹. The method was successfully used to determine the concentration of (E)-3,5,4′-trimethoxystilbene after oral administration of 86 mg kg⁻¹ of the drug to Sprague–Dawley rats and can be used to investigate the pharmacokinetics of the compound.     

Isolation and Simultaneous Determination of Coumarin Compounds in Radix Angelica dahurica

For the first time simple, rapid, and systematic methods have been established for preparative isolation and purification of coumarin compounds in an important traditional Chinese Medicine, Radix Angelica dahurica, and for simultaneous determination of several of the compounds in the medicine. Bergapten, imperatorin, and cnidilin, three of the biologically active coumarin compounds, were isolated from the chloroform-soluble fraction of the ethanol extract of Radix Angelica dahurica. After further purification by open column ODS chromatography the purified components were simultaneously determined, with two other coumarins (osthole and isoimperatorin), by reversed phase high-performance liquid chromatography (RP-HPLC) on a C₁₈ column, with methanol–water, 66:34 (v/v), as mobile phase at a flow rate of 0.8 mL min⁻¹. The compounds were detected by UV absorption at 310 nm. Calibration plots for all the coumarins had correlation coefficients close to unity. Limits of detection (S/N = 3) were <92 ng mL⁻¹ and limits of quantification (S/N = 10) were <259 ng mL⁻¹. Mean recovery of the coumarins was in the range 96.7–101.9% and the intra-day and inter-day precision, as relative standard deviation, was <2.3 and <2.9%, respectively. This simple, sensitive, and reproducible method can be used for quality control of Radix Angelica dahurica.     

HPTLC analysis of Withaferine A from an herbal extract and polyherbal formulations

Withania somnifera has been used in Ayurvedic medicine for treatment of depression and inflammation, and as an aphrodisiac. It contains many phytochemicals such as Withaferine A, withanine, anahygrine, tropine, and withanolides. Of these, withaferine A is considered to be the most active compound. Withaferine A was estimated in herbal extract and polyherbal formulations by high performance thin layer chromatography (HPTLC). As there is no official HPTLC protocol for quantitation of the above phytochemicals, an attempt was made to quantify withaferine A in herbal extract and polyherbal formulations produced from Withania somnifera. Precoated silica gel G (aluminium backed) plates were used as stationary phase and toluene:ethyl acetate: formic acid (50 : 15 : 5) was used as mobile phase. Detection and quantification were performed by densitometry at λ 213 nm. The linear range was 1 μg to 3 μg. This HPTLC method was found to be reproducible, accurate, and precise.     

Stability of arsenic peptides in plant extracts: off-line versus on-line parallel elemental and molecular mass spectrometric detection for liquid chromatographic separation

The instability of metal and metalloid complexes during analytical processes has always been an issue of an uncertainty regarding their speciation in plant extracts. Two different speciation protocols were compared regarding the analysis of arsenic phytochelatin (As^IIIPC) complexes in fresh plant material. As the final step for separation/detection both methods used RP-HPLC simultaneously coupled to ICP-MS and ES-MS. However, one method was the often used off-line approach using two-dimensional separation, i.e. a pre-cleaning step using size-exclusion chromatography with subsequent fraction collection and freeze-drying prior to the analysis using RP-HPLC–ICP-MS and/or ES-MS. This approach revealed that less than 2% of the total arsenic was bound to peptides such as phytochelatins in the root extract of an arsenate exposed Thunbergia alata, whereas the direct on-line method showed that 83% of arsenic was bound to peptides, mainly as As^IIIPC₃ and (GS)As^IIIPC₂. Key analytical factors were identified which destabilise the As^IIIPCs. The low pH of the mobile phase (0.1% formic acid) using RP-HPLC–ICP-MS/ES-MS stabilises the arsenic peptide complexes in the plant extract as well as the free peptide concentration, as shown by the kinetic disintegration study of the model compound As^III(GS)₃ at pH 2.2 and 3.8. But only short half-lives of only a few hours were determined for the arsenic glutathione complex. Although As^IIIPC₃ showed a ten times higher half-life (23 h) in a plant extract, the pre-cleaning step with subsequent fractionation in a mobile phase of pH 5.6 contributes to the destabilisation of the arsenic peptides in the off-line method. Furthermore, it was found that during a freeze-drying process more than 90% of an As^IIIPC₃ complex and smaller free peptides such as PC₂ and PC₃ can be lost. Although the two-dimensional off-line method has been used successfully for other metal complexes, it is concluded here that the fractionation and the subsequent freeze-drying were responsible for the loss of arsenic phytochelatin complexes during the analysis. Hence, the on-line HPLC–ICP-MS/ES-MS is the preferred method for such unstable peptide complexes. Since freeze-drying has been found to be undesirable for sample storage other methods for sample handling needed to be investigated. Hence, the storage of the fresh plant at low temperature was tested. We can report for the first time a storage method which successfully conserves the integrity of the labile arsenic phytochelatin complexes: quantitative recovery of As^IIIPC₃ in a formic acid extract of a Thunbergia alata exposed for 24 h to 1 mg As^v L⁻¹ was found when the fresh plant was stored for 21 days at 193 K. Figure On-line HPLC–ICP-MS/ES-MS (bottom) is the preferred method for MS determination of unstable arsenic peptide complexes in plant extracts, since this avoids fractionation and subsequent freeze-drying that are responsible for loss of arsenic phytochelatin complexes in the 2D off-line method (top) Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.