Extraction procedures for the determination of heavy metals in contaminated soil and sediment

Extraction tests are commonly used to study the mobility of metals in soils and sediments by mimicking different environmental conditions or dramatic changes on them. The results obtained by determining the extractable elements are dependent on the extraction procedure applied. The paper summarises state of the art extraction procedures used for heavy metal determination in contaminated soil and sediments. Two types of extraction are considered: single and sequential. Special attention is paid to the Standard, Measurement and Testing projects from the European Commission which focused on the harmonisation of the extraction procedures and on preparing soil and sediment certified reference materials for extractable heavy metal contents.     

海湾河口表层沉积物中重金属形态连续萃取方法的优化研究

采用单一萃取程序对建立的重金属形态连续萃取方法的萃取条件进行优化.分别以Ca和Mg、Fe、有机质(OM)和酸可挥发性硫(AVS)作为萃取剂释放酸溶态、还原态、有机质结合态和硫化物结合态等重金属目标形态的表征参量,考察萃取剂对相应目标形态的萃取能力和选择性.分别根据表征参量和重金属在萃取溶液中的含量变化确定最优萃取时间和萃取样液比.结果表明,优化萃取条件后,萃取剂对目标形态重金属均有很强的释放能力.酸溶态萃取剂对其它非残留态影响很小;还原态萃取剂除对酸溶态有少量提取外,对其它形态影响较小;有机质结合态萃取剂对硫化物结合态有少量萃取,对其它形态影响较小.硫化物结合态在酸溶态、还原态和有机质结合态之后萃取,避免了对这三种形态的影响.优化后的连续萃取方法对重金属形态有较好的选择性,可对海湾和河口表层沉积物中重金属的目标形态进行较为合理地分离和评价.     

Comparison of Two Sequential Extraction Procedures for Trace Metal Partitioning in Sediments

Abstract

Two sequential extraction schemes (a modified Tessier procedure with five steps and a three steps protocol designed by BCR) are applied to four sediment samples with different heavy metal contents. The results obtained for Cd, Cr, Cu, Ni, Pb and Zn partitioning show that the metal distribution obtained with both procedures are significantly different. With the second procedure amounts of all the heavy metals are extracted with the oxidizing reagent (third fraction) whereas with the first one the non residual metals are distributed among the second, third and fourth fractions (acetic acid-acetate buffer (pH=5), reducing and oxidizing reagents respectively). The residual fraction obtained applying the three steps procedure is in general higher than that obtained using the five steps procedure, except for cadmium.     

不同提取方法对巴戟天中金属元素含量影响的初步探讨

采用了水提、醇提及模拟胃酸浓度的酸提法对巴戟天药材进行提取,并用火焰原子吸收分光光度法分别对其中的金属元素含量进行了测定。实验结果表明,三种提取方法中,醇提法金属溶出量最少,对于有害重金属含量较高的中药,可以在中药提取的工艺当中,利用不同的提取方法除去有害重金属。通过对三种提取方法所得的提取液中Pb、Cd的存在形态研究表明,Cd在工艺过程除去相对较容易,而Pb较困难,所以应在种植巴戟天时注意避免土壤及水源的Pb污染。     

Three-step extraction procedure for determination of heavy metals availability to vegetables

A three-step sequential extraction procedure was used to determine the concentration of heavy metal speciation forms in soil. The procedure allows one to identify the pool of heavy metals that can be potentially mobilised under changes in soil pH value or redox potential. It has been shown that similar portions of heavy metals are present in reducible, oxidisable and residual fractions. It was found that soil chemical properties significantly affected the distribution of heavy metals among different fractions and their uptake by vegetables. Cadmium was a dominant element which occurred in the exchangeable fraction—the most bioavailable and potentially toxic.     

Application of ultrasound-assisted extraction to the determination of contaminants in food and soil samples

The application of ultrasound-assisted extraction (UAE) to the sample preparation of environmental and food samples has increased in the last years. This technique has been used in the development of methods for the analysis of numerous contaminants, including organic compounds (pesticides, pharmaceuticals, polycyclic aromatic hydrocarbons, polyhalogenated flame retardants, etc.) and heavy metals. The aim of this work is to review the application of this extraction procedure to the analysis of contaminants in food and soil and the comparison of its use with other well-established extraction procedures. The advantages and disadvantages of this technique together with the possibility of coupling UAE with other analytical techniques will be also discussed.     

Assessment of heavy metals leachability from metallo-organic sorbent-iron humate-with the aid of sequential extraction test

The sequential extraction test, known as a BCR procedure, was used to assess a leachability of heavy metals (Zn, Cd, Pb, Cu) from the metallo-organic sorbent—iron humate—loaded with these metals. The sequential test allowed to discriminate between various fractions of heavy metals, namely the acid-extractable fraction, the fraction bound to Fe oxides, and the fraction bound to organic matter. It was proven that the heavy metals are bound mainly to Fe oxides and organic matter, and thus they may be relatively hardly liberated into the environment. The BCR sequential extraction test exhibited a very good repeatability, when it was applied to the loaded sorbent—relative standard deviations were typically lower than 10%.     

Microanalytical flow-through method for assessment of the bioavailability of toxic metals in environmental samples

The application of a recently proposed microanalytical flow-through system for on-line sequential extraction of heavy metals from solid samples of environmental interest is described. Using various extraction schemes (a nitric acid scheme, a two-stage extraction scheme using two reagents applied in the BCR procedure) and comparison with the common batch sequential BCR procedure, the suitability of the system for fast screening of solid environmental samples is demonstrated. By pumping leaching agents sequentially through the sample held in a micro cartridge, the different metal fractions present can be assessed in less than an hour. Method evaluation was performed using SRM 1648 urban particulate matter and BCR 701 lake sediment reference material certified for extractable metals. The need for and design of laboratory internal reference material suitable for simulating the natural (dynamic) processes of metal release into the environment is also discussed. For the first time correlation is sought between fractionation techniques and physiologically based methods for assessment of the bioaccessibility of metals in biomatrices.     

Metal fractionation in olive oil and urban sewage sludges using the three-stage BCR sequential extraction method and microwave single extractions

The conventional three-stage BCR sequential extraction method was employed for the fractionation of heavy metals in sewage sludge samples from an urban wastewater treatment plant and from an olive oil factory. The results obtained for Cu, Cr, Ni, Pb and Zn in these samples were compared with those attained by a simplified extraction procedure based on microwave single extractions and using the same reagents as employed in each individual BCR fraction. The microwave operating conditions in the single extractions (heating time and power) were optimized for all the metals studied in order to achieve an extraction efficiency similar to that of the conventional BCR procedure. The measurement of metals in the extracts was carried out by flame atomic absorption spectrometry. The results obtained in the first and third fractions by the proposed procedure were, for all metals, in good agreement with those obtained using the BCR sequential method. Although in the reducible fraction the extraction efficiency of the accelerated procedure was inferior to that of the conventional method, the overall metals leached by both microwave single and sequential extractions were basically the same (recoveries between 90.09 and 103.7%), except for Zn in urban sewage sludges where an extraction efficiency of 87% was achieved. Chemometric analysis showed a good correlation between the results given by the two extraction methodologies compared. The application of the proposed approach to a certified reference material (CRM-601) also provided satisfactory results in the first and third fractions, as it was observed for the sludge samples analysed.     

Speciation of Heavy Metals in Soils and Sediments. An Account of the Improvement and Harmonization of Extraction Techniques Undertaken Under the Auspices of the BCR of the Commission of the European Communities

Abstract

An account is presented of a series of investigations and collaborative studies, initiated by BCR, on current methods of metal speciation by extraction of soils and sediments with chemical reagents. It was established by extensive consultation with European experts that the diverse procedures used could be harmonized into agreed methods. These methods, including both single extractant and sequential extraction procedures were subjected to collaborative, interlaboratory trials and the results, presented briefly here, showed that it was both possible and desirable that reference soils and sediments, characterised by certified values for extractable contents, be prepared. As a consequence of these studies two soils have been prepared and will shortly be the subject of interlaboratory analysis with a view to certification of their EDTA and acetic acid extractable contents of some heavy metals. Following this workshop a feasibility study of the agreed sequential extraction procedure will, it is believed, shortly lead to certification of sediments for contents extractable by a defined sequential extraction procedure.     

氧化与还原条件下伊通河长春区段沉积物重金属形态特征的对比研究

利用改进的Tessier连续萃取法研究了伊通河长春市自由大桥处不同深度沉积物样品在氧化及还原条件下Cu,Pb,Zn和Ni的形态变化规律,同时分析了沉积物样品中酸可挥发性硫(Acid volatile sulfide,AVS)和同时提取重金属(Simultaneous extract metals,SEM)的含量. 实验结果表明，样品经干燥、研磨处理后,Cu有机/硫化物结合态比例减少40%,锰氧化物结合态的比例显著增加; Pb,Zn和Ni 3种元素有机/硫化物结合态比例均略有下降,变化幅度小于Cu,并重新分配到不同的化学相中. 通过SEM中各金属含量与有机/硫化物结合态中金属含量的对比可知,还原性沉积物中Cu除了与硫化物结合外,很大一部分是以有机物形态存在的,Pb,Zn,Ni,Fe和Mn则主要以硫化物形态存在,各元素形态分析均不同程度地受到萃取剂的影响.     

Procedures for a fast separation of berkelium from complex mixtures of reaction products

Two procedures are described for fast separations of berkelium from complex mixtures of reaction products arising from heavy ion reactions, such as¹⁸O+²⁴⁸Cm. The first procedure uses a combination of several extraction steps with a final separation on a cation exchanger, the second procedure starts with an anion exchange column which is followed by multiple extractions in different media. The elements separated in the different steps were analyzed and overall decontamination factors are given.     

Bioextraction of heavy metals from colloidal sludge systems

Chemical (acidic) and biological (under the action of acidogenic metabolites synthesized by microorganisms present in a sediment) extraction of heavy metals from colloidal sludge sediments produced at a wastewater biochemical treatment plant is studied. It is established that both methods provide at least 80% extraction of heavy metals, which decreases in the sequence Zn > Mn > Cu > Ni > Co > Pb > Cr. The advantage of the biological procedure is the possibility of using the processed sludge sediments, which contain many useful components, as fertilizers.     

Reservoir recultivation versus forms of heavy metals in sediments: the case of the Kielce City Lake

The Kielce Lake is a water reservoir located in the Kielce city zone. Areas around the reservoir are used for recreational, residential and industrial purposes. Additionally, the nearby state road to the city of Łódź, is a source of transportation pollution, including heavy metals. The reservoir is fed by a watercourse which receives municipal wastewater from the town of Masłów near Kielce. The amount and diversity of organic and inorganic compounds which flow into the reservoir causes heavy pollution of the Lake waters. To reduce the degree of reservoir pollution, a pulverizing aerator was installed in the middle of the Kielce Lake in May 2008. Sediment samples were collected at a depth of 0–20 cm between July 2008 and May 2010 at five sites in the littoral zone of the recultivation area. These environmental samples underwent a five-stage sequential extraction procedure, assisted by microwave radiation. The concentrations of trace metals Zn, Cu, Ni, Cr, Pb, Mn, Fe and Cd in various extracts were determined by means of F-AAS and GF-AAS. The results have shown a high concentration of analytes in reservoir sediments.     

连续萃取法研究海湾养殖区沉积物中重金属形态

以连续萃取法研究海湾养殖区沉积物中重金属(Cd, Cu, Pb, Zn)的形态,将重金属分离为酸溶态、还原态、有机质结合态、硫化物结合态和残渣态.分别采用基体匹配法和内标法消除高盐基体对电感耦合等离子体光谱法(ICP-OES)和质谱法(ICP-MS)分析结果的影响.对海洋沉积物标准物质分析结果表明,样品稀释后测定值与标准值一致.比较了本连续萃取法和BCR法对沉积物样品中重金属形态的提取结果,并考察了萃取剂的选择性.实验表明,本方法可用于有机质污染和富营养化环境沉积物中重金属形态分析,特别是有机质结合态和硫化物结合态的分析.     

The utilization of modified BCR three-step sequential extraction procedure for the fractionation of Cd, Cr, Cu, Ni, Pb and Zn in soil reference materials of different origins

A modified three-step sequential extraction procedure for the fractionation of heavy metals, proposed by the Commission of the European Communities Bureau of Reference (BCR) has been applied to the Slovak reference materials of soils (soil orthic luvisols, soil rendzina and soil eutric cambisol), which represent pedologically different types of soils in Slovakia. Analyses were carried out by flame or electrothermal atomic absorption spectrometry (FAAS or ETAAS). The fractions extracted were: exchangeable (extraction step 1), reducible-iron/manganese oxides (extraction step 2), oxidizable-organic matter and sulfides (extraction step 3). The sum of the element contents in the three fractions plus aqua-regia extractable content of the residue was compared to the aqua-regia extractable content of the elements in the origin soils. The accuracy obtained by comparing the determined contents of the elements with certified values, using BCR CRM 701, certified for the extractable contents (mass fractions) of Cd, Cr, Cu, Ni, Pb and Zn in sediment following a modified BCR-three step sequential extraction procedure, was found to be satisfactory.     

Solution extraction of transition and post-transition heavy and precious metals by chelate and macrocyclic ligands

This review focuses on compounds and methods that can be used for the extraction and separation from solution of two classes of elements that we define as heavy metals and precious metals. These elements are often targeted because they are toxic, costly, and their coordination chemistry has already been well studied, and because there is a need to develop methods of economically extracting, separating and recovering them from waste sites. This review outlines possible strategies that can be used, and reviews the present literature regarding the available methods for their extraction.     

缺氧沉积物中重金属形态连续萃取方法的稳定性研究

考察了海水养殖区域缺氧沉积物中重金属形态连续萃取法萃取过程中溶液pH值、温度变化和胶体形成对形态分离结果的影响。结果表明,连续萃取法Step1萃取酸溶态时,萃取液pH值的轻微升高使Pb和Zn的萃取结果明显降低;Step2萃取还原态时,萃取液pH值明显升高对重金属的萃取结果影响很小;Step3萃取有机质结合态时,萃取液pH值的降低对重金属萃取结果影响较小(除Pb外)。由于连续萃取法中各步萃取反应的热力学过程不同,Step1和Step2萃取后溶液温度轻微升高而在Step3中溶液温度稍微降低,溶液温度变化(<2.5℃)对重金属形态的影响很小。在Step1、Step2和Step4萃取过程中胶体的形成和存在,对萃取液Cd、Zn和Cu有明显的吸附影响;而在Step3萃取中萃取剂的分散作用有效控制了溶液中胶体的形成。因此采用连续萃取方法评价沉积物中的重金属形态时,控制萃取液pH值和胶体形成有利于提高萃取结果的稳定性和准确性。     

Fractionation of heavy metals in sediment by using microwave assisted sequential extraction procedure and determination by inductively coupled plasma mass spectrometry

In this work, a fast microwave assisted extraction procedure was developed and optimized for the heavy metals (Cu, Ni, Cr, Pb and Cd) partitioning in the three-stage sequential extraction procedure proposed by the European Standards, Measurements and Testing (SM&;T) Program, formerly the Community Bureau of Reference (BCR). The microwave oven procedure was optimized to obtain extraction efficiencies similar to the conventional BCR procedure, in less time, while using smaller volumes of reagents. In the optimization process, three variables (extraction time, ramping time and microwave power) were considered as factors and as a response the concentration of different metal ions in each individual BCR fraction. Interactions between analytical factors and their optimized levels were investigated using a central composite design. Extractable metals obtained by both comparable methodologies were measured by inductively coupled plasma mass spectrometry. With the use of optimal microwave conditions, steps 1–3 of the sequential extraction (including the hydrogen peroxide digestion in step 3) could be completed between 21 and 22 min. Detection limits were between 1 and 18 ng l^{− 1}. The accuracy of the proposed method was checked with a certified reference material (CRM) of Lake Sediment BCR 701. Values obtained were in accordance with those reported for the certified material with only a few exceptions. Different origin sediments (river and marine) were analyzed by both BCR and MW procedures, and the results obtained were comparable according to the t-paired-test for a 95% confidence level.     

Comparison of three sequential extraction procedures for fractionation of arsenic from highly polluted mining sediments

Three sequential extraction procedures were evaluated for the study of fractionation of arsenic in environmental solid samples. The procedures considered were as follows: i) the standardized and widely recognised BCR procedure, conceived for the study of the partitioning of heavy metals; ii) the procedure developed by Manful, who adapted a phosphorus scheme for arsenic fractionation; and iii) a novel sequential extraction scheme especially devised for arsenic. The efficiency and suitability of these methods and the corresponding extraction steps for partitioning arsenic obtained from the most important solid forms were tested by application of the methods to real sediment samples heavily polluted by mining activity. Results showed the BCR scheme was inappropriate for arsenic fractionation. The procedure could, nevertheless, be a first approach for the assessment of arsenic partitioning, because its first extraction step can be regarded as adequate for the estimation of the most easily mobilizable arsenic. Although the Manful scheme results in a more differentiated arsenic pattern, some drawbacks arise from the lack of selectivity of some of the reagents used, for example overlapping of specific target phases, overestimation of adsorbed arsenate because of inadequate coprecipitation processes, and the inability to discriminate among amorphous and crystalline oxyhydroxides which are mainly responsible for arsenic retention. The novel procedure achieves the most suitable arsenic fractionation, because the main phases retaining arsenic are selectively targeted according to mobilization potential. In addition, the simplicity of its extraction steps would enable automation in a continuous flow scheme.