<Emphasis Type="Italic">S,S,S</Emphasis>-Tris(2-ethylhexyl) phosphorotrithioate as an effective solvent mediator for a mexiletine-sensitive membrane electrode

S,S,S-Tris(2-ethylhexyl) phosphorotrithioate proved to be an effective solvent mediator for constructing a mexiletine-sensitive membrane electrode in combination with an ion-exchanger, sodium tetrakis[3,5-bis(2-methoxyhexafluoro-2-propyl)phenyl]borate. Among a series of phosphorus compounds containing phosphoryl (P=O) groups, this solvent mediator showed the highest sensitivity to mexiletine in phosphate-buffered physiological saline containing 0.15 mol L⁻¹ NaCl and 0.01 mol L⁻¹ NaH₂PO₄/Na₂HPO₄ (pH 7.4), giving a detection limit of 2 × 10⁻⁶ mol L⁻¹ with a slope of 58.8 mV decade⁻¹. This is the best reported detection limit of any mexiletine-sensitive electrode developed to date. Owing to its high selectivity toward inorganic cations, the electrode was used to determine the level of mexiletine in saliva, the monitoring of which is quite effective for controlling the dose of this drug noninvasively. The mexiletine concentrations determined with the mexiletine-sensitive electrode compared favorably with those determined by high-performance liquid chromatography.     

Properties of naproxen ion-selective electrodes

Naproxen membrane electrodes based on different plasticizers and the quaternary ammonium salts (QASs) dimethyldidecylammonium bromide, methyltrioctylammonium chloride, or tetraoctylammonium chloride, were prepared. The following basic parameters were investigated for the optimal electrode: measurement range (10⁻⁴ − 10⁻¹ mol L⁻¹), slope of the linear range of the calibration curve (−58.3 mV decade⁻¹), limit of detection (6.0 × 10⁻⁵ mol L⁻¹), lifetime (2.5 months), dependence of the electrode potential on pH (5.5 − 9.0), reproducibility of potential (1.2 mV) and selectivity coefficients in relation to selected organic and inorganic anions. The electrode was utilized for determination of naproxen in tablets by the calibration curve method and the standard addition method.      

Silver(I)-selective electrode based on [Bz2Oxo4(18)dieneS4] tetrathia macrocyclic carrier

A polystyrene-based membrane of 7,8:16,17-dibenzo-6,9,15,18-tetraoxo-1,5,10,14-tetrathiacyclooctadeca-7,16-diene [Bz₂Oxo₄(18)dieneS₄] was fabricated using sodium tetraphenylborate (NaTPB) and dioctyl phthalate (DOP) as anion excluder and plasticizing agent. The best performance was obtained from the membrane with the composition ionophore [Bz₂Oxo₄(18)dieneS₄]:polystyrene:DOP:NaTPB, 5:100:150:10 (w/w). The response of the electrode was linear over a wide range of concentration, 1.26×10^–6–1.00×10^–1 mol L⁻¹ for silver ion with a Nernstian slope of 58.4±0.1 mV per decade and a detection limit of 1.0×10⁻⁶ mol L⁻¹. The electrode was found to be chemically inert and of adequate stability with a response time of 10 s and could be used for a period of 3 months without change of potential. It worked satisfactorily in mixtures containing up to 35% (v/v) non-aqueous content. The proposed membrane sensor had good selectivity for Ag⁺ over a wide variety of metal ions in the pH range 2.2–8.5. It was successfully used as an indicator electrode in potentiometric titration of silver ion. The electrode was also useful for determination of Ag⁺ in waste from photographic films.     

Determination of p-nitroaniline by the tartrate-acetone-Mn2+-KBrO3-H2SO4 double organic substrate oscillating system using non-equilibrium stationary state

This paper described the determination of p-nitroaniline in a double organic substrate oscillating system of tartrate-acetone-Mn²⁺-KBrO₃-H₂SO₄. Under the optimum conditions, temperature was chosen as a control parameter to design the bifurcation point and proposed a convenient method for determination of p-nitroaniline. Results showed that the system consisting of 3.5 mL 0.06 mol L⁻¹ tartrate, 4.0 mL 0.7 mol L⁻¹ H₂SO₄, 1.5 mL 1.5×10⁻⁴ mol L⁻¹ MnSO₄, 4.0 mL 0.4 mol L⁻¹ acetone and 7.0 mL 0.05 mol L⁻¹ KBrO₃ was very sensitive to the surrounding at 33.5°C. A good linear relationship between the potential difference and the negative logarithm concentration of p-nitroaniline was obtained to be in the range of 2.50×10⁻⁷∼3.75×10⁻⁵ mol L⁻¹ with a lower detection limit of 2.50×10⁻⁸ mol L⁻¹.      

Determination of Selenium in Biological Materials Using an Ion-Selective Electrode

A method was developed for determining selenium with a self-made ion-selective electrode was developed. This electrode was made by using Ag₂Se as electroactive material. Optimal working conditions and interferences were investigated. The electrode exhibits good potentiometric response for Se²⁻ ions over the concentration range from 6 × 10⁻⁷ mol · L⁻¹ to 1 × 10⁻⁴ mol · L⁻¹ with a Nernstian slope of 28 ± 1 mV per decade and a detection limit of about 4.5 × 10⁻⁷ mol · L⁻¹. It was used over six months and exhibits good selectivity and sensitivity towards Se²⁻. The method was applied to determine selenium in biological materials. The recovery ranges between 92% and 105.5%, and the relative standard derivation is less than 3.6% (n = 6).     

Trace determination of clenbuterol with an MWCNT-Nafion nanocomposite modified electrode

A method for the determination of trace clenbuterol is described. Multi-walled carbon nanotubes (MWCNTs)-Nafion composite was used to modify the glassy carbon electrode (GCE). The modified electrode showed high sensitivity and good selectivity for clenbuterol detection. It offered a linear range of 1.0 × 10⁻⁹–1.0 × 10⁻⁶ mol · L⁻¹ with a detection limit of 5.0 × 10⁻¹⁰ mol · L⁻¹ in pH = 1.2 solution. The oxidation mechanism of clenbuterol on the electrode was also investigated. Correspondence: Xiao-Ya Hu, Department of Chemistry, Yang Zhou University, Yang Zhou, Jiang Su, P.R. China     

Cobalt(II) ion-selective electrode with solid contact

A new all plastic sensor for Co²⁺ ions based on 2-amino-5 (hydroxynaphtyloazo-1′)-1,3,4 thiadiazole (ATIDAN) as ionophore was prepared. The electrode exhibits a low detection limit of 1.5 × 10⁻⁶ mol L⁻¹ and almost theoretical Nernstian slope in the activity range 4.0 × 10⁻⁶–1 × 10⁻¹ mol L⁻¹ of cobalt ions. The response time of the sensor is less than 10 s and it can be used over a period of 6 months without any measurable divergence in potential. The proposed sensor shows a fairly good selectivity for Co(II) over other metal ions. The electrode was successfully applied for determination of Co²⁺ in real samples and as an indicator electrode in potentiometric titration of Co²⁺ ions with EDTA.      

Determination of rutin using a CeO2 nanoparticle-modified electrode

CeO₂ nanoparticles approximately 12 nm in size were synthesized and subsequently characterized by XRD, TEM and UV-vis spectroscopy. Then, a gold electrode modified with CeO₂ nanoparticles was constructed and characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The modified electrode demonstrated strong catalytic effects with high stability towards electrochemical oxidation of rutin. The anodic peak currents (measured by differential pulse voltammetry) increased linearly with the concentration of rutin in the range of 5.0 × 10⁻⁷–5.0 × 10⁻⁴ mol · L⁻¹. The detection limit (S/N = 3) was 2.0 × 10⁻⁷ mol · L⁻¹. The relative standard deviation (RSD) of 8 successive scans was 3.7% for 5.0 × 10⁻⁶ mol · L⁻¹ rutin. The method showed excellent sensitivity and stability, and the determination of rutin in tablets was satisfactory.     

Platinum electrode coated with a bentonite–carbon composite as an environmental sensor for detection of lead

A Pt wire coated with a bentonite–carbon composite in a poly(vinyl chloride) membrane was used for detection of lead. The sensor has a Nernstian slope of 29.42±0.50 mV per decade over a wide range of concentration, 1.0×10⁻⁷ to 1.0×10⁻³ mol L⁻¹ Pb(NO₃)₂. The detection limit is 5.0×10⁻⁸ mol L⁻¹ Pb(NO₃)₂ and the electrode is applicable in the pH range 3.0–6.7. It has a response time of approximately 10 s and can be used at least for three months. The electrode has good selectivity relative to nineteen other metal ions. The practical analytical utility of the electrode is demonstrated by measurement of Pb(II) in industrial waste and river water samples.     

Flow screen-printed amperometric detection of p-nitrophenol in alkaline phosphatase-based assays

p-Nitrophenyl phosphate is one of the most widely used substrates for alkaline phosphatase in ELISAs because its yellow, water-soluble product, p-nitrophenol, absorbs strongly at 405 nm. p-Nitrophenol is also electroactive; an oxidative peak at 0.97 V (vs. an Ag pseudoreference electrode) is obtained when a bare screen-printed carbon electrode is used. When an amperometric detector was coupled to a flow-injection analysis system the detection limit achieved for p-nitrophenol was 2×10⁻⁸ mol L⁻¹, almost two orders of magnitude lower than that obtained by measuring the absorbance of the compound. By use of this electrochemical detection method, measurement of 7×10⁻¹⁴ mol L⁻¹ alkaline phosphatase was achieved after incubation for 20 min. The feasibility of coupling immunoassay to screen-printed carbon electrode amperometric detection has been demonstrated by performing an ELISA for detection of pneumolysin, a toxin produced by Streptococcus pneumoniae, which causes respiratory infections. The method is simple, reproducible, and much more sensitive than traditional spectrophotometry.     

A sensitive nicotine sensor based on molecularly imprinted electropolymer of o-aminophenol

A sensitive nicotine sensor based on a molecularly imprinted electropolymer of o-aminophenol is proposed and its configuration and performance are studied in detail. On the condition of weak acidity, the sensitive layer was prepared by electropolymerization of o-aminophenol on a gold electrode in the presence of the template (nicotine). The sensor exhibits good selectivity and sensitivity to nicotine. The determination limit is 2.0×10⁻⁷ mol/L and a linear relationship between the current and concentration is found in the range of 4.0×10⁻⁷ ∼ 3.3 ×10⁻⁵ mol/L. The sensor has also been applied to the analysis of nicotine in tobacco samples with recovery rates ranging from 99.0% to 102%. __________ Translated from Journal of Hunan university (Nature Science), 2005, 32(3) (in Chinese)     

Simultaneous voltammetric measurement of ascorbic acid and dopamine on poly(caffeic acid)-modified glassy carbon electrode

A poly(caffeic acid) thin film was deposited on the surface of a glassy carbon electrode by potentiostatic technique in an aqueous solution containing caffeic acid. The poly(caffeic acid)-modified electrode was used for the determination of ascorbic acid (AA), dopamine (DA), and their mixture by cyclic voltammetry. This modified electrode exhibited a potent and persistent electron-mediating behavior followed by well-separated oxidation peaks toward AA and DA at a scan rate of 10 mV s⁻¹ with a potential difference of 135 mV, which was large enough to determine AA and DA individually and simultaneously. The catalytic peak current obtained was linearly dependent on the AA and DA concentrations in the range of 2.0 × 10⁻⁵−1.2 × 10⁻³ and 1.0 × 10⁻⁶−4.0 × 10⁻⁵ mol L⁻¹ in 0.15 mol L⁻¹ phosphate buffer (pH 6.64). The detection limits for AA and DA were 9.0 × 10⁻⁶ and 4.0 × 10⁻⁷ mol L⁻¹, respectively. The modified electrode shows good sensitivity, selectivity, and stability and has been applied to the determination of DA and AA in real samples with satisfactory results.     

Properties of ibuprofen ion-selective electrodes based on the ion pair complex of tetraoctylammonium cation

Ibuprofen membrane electrodes based on different plasticizers: diisobutyl phthalate (DIBP), o-nitrophenyloctyl ether (o-NPOE), dioctyl sebacate (DOS) and tetraoctylammonium 2-(4-isobutylphenyl)propionate were prepared. All electrodes show: a near Nernstian slope of characteristic (58.3–60.9 mV decade⁻¹) in the measurement range (10⁻⁴–10⁻¹ mol L⁻¹), limit of detection (5.0×10⁻⁵ mol L⁻¹), really long lifetime (12 months), dependence of the electrode potential on pH (5.5–9.0), reproducibility of potential (0.6–1.2 mV) and selectivity coefficients in relation to some organic and inorganic anions. The electrodes were applied for the determination of ibuprofen in tablets by the calibration curve method and the standard addition method.      

Highly-sensitive ion selective electrode based on molecularly imprinted polymer particles for determination of tetracycline in aqueous samples

In this work, a highly-sensitive polymeric membrane ion selective electrode for determination of tetracycline was constructed by using molecularly imprinted polymer (MIP) particles as quasi-ionophore. The water-compatible MIP particles targeting tetracycline were synthesized with tetracycline as a template molecule, methacrylic acid as a functional monomer, ethylene glycol dimethacrylate as a cross-linker, 2,2′-azobisisobutyronitrile as an initiator and lanthanum ion as a mediator. Benefited from the distinctive performance of the quasi-ionophore and the optimized composition of the membrane and the inner filling solution, the lower detection limit of the electrode was decreased to about 1 × 10⁻⁸ mol/l. It exhibited a good electrode slope 59.8 mV/decade near the theoretical Nernstian one, with a wide linear working range from 2.0 × 10⁻⁸ to 1.0 × 10⁻³ mol/l. Due to the specific recognition of tetracycline by the MIP particles, the selectivity coefficients for routine interferences were less than 10⁻⁴. The fabricated electrode should be used in pH 2–4, response time of which was less than 200 s when the concentration of tetracycline was higher than 1.0 × 10⁻⁶ mol/l and no more than 30 min at the concentration of 1.0 × 10⁻⁸ mol/l. Finally, the proposed highly-sensitive ion selective electrode has been successfully applied to the determination of tetracycline in aqueous samples.     

Spectrophotometric determination of trace amounts of iodide-ions in form of ionic associate with brilliant green using electrochemical oxidation

A combined method involving electrochemical oxidation of iodide to iodate at a platinum electrode followed by extraction in CCl₄ of ionic associates of iodine-iodide complexes with brilliant green, formed in excess of iodide, was developed for the spectrophotometric quantification of iodide. The slope of the calibration curve yields a molar extinction coefficient of ɛ = 3·10⁵ L mol⁻¹cm⁻¹. This method can be used for the quantification of iodide in the concentration range of 3·10⁻⁷ − 3·10⁻⁶ mol L⁻¹ with a detection limit of 5·10⁻⁸ mol L⁻¹. The interfering effect of other ions on the determination of the iodide concentration was also investigated. The method was successfully applied for the determination of iodide in real samples of NaCl and spring water. Relative standard deviation is 1–2%.     

Tripodal chelating ligand-based sensor for selective determination of Zn(II) in biological and environmental samples

Potassium hydrotris(N-tert-butyl-2-thioimidazolyl)borate [KTt^t-Bu] and potassium hydrotris(3-tert-butyl-5-isopropyl-l-pyrazolyl)borate [KTp^t-Bu,i-Pr] have been synthesized and evaluated as ionophores for preparation of a poly(vinyl chloride) (PVC) membrane sensor for Zn(II) ions. The effect of different plasticizers, viz. benzyl acetate (BA), dioctyl phthalate (DOP), dibutyl phthalate (DBP), tributyl phosphate (TBP), and o-nitrophenyl octyl ether (o-NPOE), and the anion excluders sodium tetraphenylborate (NaTPB), potassium tetrakis(p-chlorophenyl)borate (KTpClPB), and oleic acid (OA) were studied to improve the performance of the membrane sensor. The best performance was obtained from a sensor with a of [KTt^t-Bu] membrane of composition (mg): [KTt^t-Bu] (15), PVC (150), DBP (275), and NaTPB (4). This sensor had a Nernstian response (slope, 29.4 ± 0.2 mV decade of activity) for Zn²⁺ ions over a wide concentration range (1.4 × 10⁻⁷ to 1.0 × 10⁻¹ mol L⁻¹) with a limit of detection of 9.5 × 10⁻⁸ mol L⁻¹. It had a relatively fast response time (12 s) and could be used for 3 months without substantial change of the potential. The membrane sensor had very good selectivity for Zn²⁺ ions over a wide variety of other cations and could be used in a working pH range of 3.5–7.8. The sensor was also found to work satisfactorily in partially non-aqueous media and could be successfully used for estimation of zinc at trace levels in biological and environmental samples. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Electrocatalytic oxidation of nitric oxide at nano-TiO2/Nafion composite film modified glassy carbon electrode

A novel nanocrystalline TiO₂ (nano-TiO₂) and Nafion composite film modified glassy carbon electrode has been developed for the determination of nitric oxide (NO) radical in an aqueous solution. This modified electrode can be employed as a NO sensor with a low detection limit, fast response, high sensitivity and selectivity. Two apparent anodic peaks were observed at 0.67 and 0.95 V at the nano-TiO₂ modified glassy carbon electrode by differential pulse voltammetry (DPV). After further modification with a thin film of Nafion, which was capable of preventing some anionic interference such as nitrite and ascorbic acid, only one peak appeared and the peak current enhanced greatly. The chronocoulometric experimental results showed NO was oxidized by one-electron transfer reaction at the composite film modified electrode. The amperometric responses increased linearly with the concentrations of NO ranging from 3.6×10⁻⁷ mol/L to 5.4×10⁻⁵ mol/L. The detection limit was estimated to be 5.4×10⁻⁸ mol/L. In this sensor system, the modification film provides complete selectivity for NO over nitrite anions (NO₂⁻).     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

Highly selective thiocyanate poly(vinyl chloride) membrane electrode based on a cadmium–Schiff’s base complex

A PVC membrane electrode based on a cadmium–salen (N,N′-bis-salicylidene-1,2ethylenediamine) complex as an anion carrier is described. The electrode has an anti-Hofmeister selectivity sequence with a preference for thiocyanate at pH 1.5–11.0. It has a linear response to thiocyanate from 1.0 × 10^–6 to 1.0 × 10^–1 mol L^–1 with a slope of 59.1 ± 0.2 mV per decade, and a detection limit of 7 × 10^–7 mol L^–1. This electrode has high selectivity for thiocyanate relative to many common organic and inorganic anions. The proposed sensor has a fast response time of approximately 15 s. It was applied to the determination of thiocyanate in a milk sample. Received: 1 December 2000 / Revised: 19 April 2001 / Accepted: 30 April 2001     

Simultaneous determination of oxalate, thiosulfate, and thiocyanate in urine by ion-exclusion chromatography with electrochemical detection

Summary A sensitive ion-exclusion chromatographic method has been developed for determination of oxalate, thiosulfate, and thiocyanate. The method is based on separation of these anions on a polymethacrylate-based, weakly acidic cation-exchange resin (TSKgel OApak-A) and detection by means of a glassy carbon (GC) electrode electrochemically modified with polyvinylpyridine (PVP), palladium, and iridium oxide (PVP/Pd/IrO₂). The electrochemical behavior of oxalate, thiosulfate, and thiocyanate at this chemically modified electrode (CME) have been investigated by cyclic voltammetry. The results indicated that electrocatalytic oxidation of these anions by the electrode was efficient and that the sensitivity, stability, and lifetime of the electrode were relatively high. Combined with ion-exclusion chromatography the PVP/Pd/IrO₂ electrode was used as the working electrode for amperometric detection of these anions. All linear ranges were over two orders of magnitude and detection limits, defined asS/N=3, were 9.0×10⁻⁷ mol L⁻¹ for oxalate, 6.7×10⁻⁷ mol L⁻¹ for thiosulfate, and 5.6×10⁻⁷ mol L⁻¹ for thiocyanate. Correlation coefficients were all>0.998. Coupled with microdialysis sampling the method has been successfully applied to the determination of oxalate, thiosulfate, and thiocyanate in urine.