Effect of nitrogen content on the properties of CrNxOyCz coating prepared by DC reactive magnetron sputtering

The CrN_xO_yC_z coatings were deposited by planar DC reactive magnetron sputtering onto AZ31 Mg alloy and high speed tool steel (HSTS) substrates at a substrate temperature of 200 °C. The effect of N₂ content on composition and structure of the CrN_xO_yC_z coatings was investigated. The structure of the CrN_xO_yC_z coatings was analyzed by a glancing angle X-ray diffraction (GXRD). The cross-section morphology and thickness of the CrN_xO_yC_z coatings were checked by a field emission scanning electron microscope (FESEM), and the composition profile and chemical state were carried out by an X-ray photoelectron spectroscopy (XPS). The experimental results showed that the structure and phase composition of the CrN_xO_yC_z coatings depended on N₂ content. The evolution of the structure of CrN_xO_yC_z coatings was consistent with CrN_x-based coatings, and the CrN_xO_yC_z coatings contained Cr₂O₃, CrO₂, CrO, Cr₃C₂, CrN_x (Cr, CrN, Cr₂N), as well as different chromium oxynitride. However, the carbide and oxynitride were oxidized after annealing.     

The role of co-adsorbed O2 on the catalytic reduction of NO with C2H5OH on the surface of Pt(3 3 2)

The influence of pre-dosed O₂ on the catalytic reduction of NO with ¹³C₂H₅OH on the surface of stepped Pt(3 3 2) was investigated using Fourier transform infra red reflection-absorption spectroscopy (FTIR-RAS) and thermal desorption spectroscopy (TDS). We show that the oxidation of ¹³C₂H₅OH with O₂ is a very effective reaction, occurring at 150 K and giving rise to acetate. The presence of NO does not lead to any evident oxidation of ¹³C₂H₅OH irrespective of the annealing temperature. For the case of O₂ + ¹³C₂H₅OH + NO co-adlayers, oxidation of ¹³C₂H₅OH also takes place at 150 K. However, no new surface species that are supposed to be an intermediate for the production of N₂ are detected.The influence of O₂ on the production and desorption of N₂ is intimately related to both O₂ and ¹³C₂H₅OH coverage. The presence of pre-dosed O₂ does not greatly promote N₂ desorption. In fact, N₂ desorption is suppressed quantitatively with increasing O₂ coverage, after which unreacted, or left-over O atoms appear and remain on steps. It is concluded that the presence of pre-dosed O₂ does not play a role of activating reactants in the catalytic reduction of NO with ¹³C₂H₅OH on the surface of Pt(3 3 2).     

A study of TaxC1−x coatings deposited on biomedical 316L stainless steel by radio-frequency magnetron sputtering

In this paper, Ta_xC_1−x coatings were deposited on 316L stainless steel (316L SS) by radio-frequency (RF) magnetron sputtering at various substrate temperatures (T_s) in order to improve its corrosion resistance and hemocompatibility. XRD results indicated that T_s could significantly change the microstructure of Ta_xC_1−x coatings. When T_s was <150 °C, the Ta_xC_1−x coatings were in amorphous condition, whereas when T_s was ≥150 °C, TaC phase was formed, exhibiting in the form of particulates with the crystallite sizes of about 15-25 nm (T_s = 300 °C). Atomic force microscope (AFM) results showed that with the increase of T_s, the root-mean-square (RMS) values of the Ta_xC_1−x coatings decreased. The nano-indentation experiments indicated that the Ta_xC_1−x coating deposited at 300 °C had a higher hardness and modulus. The scratch test results demonstrated that Ta_xC_1−x coatings deposited above 150 °C exhibited good adhesion performance. Tribology tests results demonstrated that Ta_xC_1−x coatings exhibited excellent wear resistance. The results of potentiodynamic polarization showed that the corrosion resistance of the 316L SS was improved significantly because of the deposited Ta_xC_1−x coatings. The platelet adhesion test results indicated that the Ta_xC_1−x coatings deposited at T_s of 150 °C and 300 °C possessed better hemocompatibility than the coating deposited at T_s of 25 °C. Additionally, the hemocompatibility of the Ta_xC_1−x coating on the 316L SS was found to be influenced by its surface roughness, hydrophilicity and the surface energy.     

On the origin of the 2.2-2.3 eV photoluminescence from chemically etched germanium

The photoluminescence (PL) at ∼2.2-2.3 eV from Ge-based nanocrystalline materials is described in the literature as nanocrystal size-independent. We have observed visible luminescence from two different types of stain-etched Ge samples, one prepared after Sendova-Vassileva et al. (Thin Solid Films 255 (1995) 282) in a solution of H₂O₂:HF at 50:1 volume ratio, and the other in a solution of HF:H₃PO₄:H₂O₂ at 34:17:1 volume ratio. Energy dispersive X-ray analysis (EDX), Raman and FTIR spectroscopy, and the near edge X-ray absorption structure (XANES), indicate that the chemically etched Ge layers of the former type of samples are composed of non-stoichometric Ge oxides, i.e. GeO_x (0<x<2), and free from any Ge nanoconstructions. It is also suggested from XANES that the latter type of chemically etched Ge samples comprise 8-9 nm nanocrystals of Ge, surface-covered with mainly oxygen. Photoluminescence occurred at ∼2.3 eV for all samples. The PL behavior of the latter type of chemically etched Ge on annealing in different chemical environments (air or H) allowed us to conclude that the PL from these materials, as well as that from those Ge-based nanocrystalline materials reported in the literature, is from GeO_xs.     

Using of chelating resin to study the kinetic desorption of Eu(III) from humic acid-Al2O3 colloid surfaces

The association of organic-inorganic colloid-borne trace elements was investigated. Radionuclide ^152+154Eu(III) was chosen as a representative and chemical homologue for trivalent lanthanide and actinide ions present in radioactive nuclear waste. Effect of pH and contact time of organic-inorganic/Eu(III) on the kinetic dissociation of Eu(III) from HA-Al₂O₃ colloids was studied. The kinetic desorption behavior of sorbed ^152+154Eu(III) from humic acid-γ-Al₂O₃ colloids was studied at pH values of 4.5 ± 0.2, 5.3 ± 0.2 and 6.5 ± 0.2, respectively, by the addition of the chelating resin. The experimental results suggest that the fractions of irreversible sorption of radionuclide ^152+154Eu(III) to HA-Al₂O₃ colloids increase with increasing pH values, and are independent of aging time. At least two different species, “weak” and “strong” dissociation fractions, are required to simulate the kinetic desorption of ^152+154Eu(III) from HA-Al₂O₃ colloids. The species of Eu(III) sorbed on HA-Al₂O₃ colloids move from “weak” sites to “strong” sites with increasing aging time, whereas the fractions of irreversible sorption are independent of aging time. The results are important for the evaluation of radionuclides’ behavior in the environment.     

Planar nano-block structures Tin+1Al0.5Cn and Tin+1Cn (n = 1, and 2) from MAX phases: Structural,electronic properties and relative stability from first principles calculations

Structural, electronic properties and relative stability of quasi-two-dimensional (2D) free-standing planar nano-block (NBs) structures Ti_n+1Al_0.5C_n and Ti_n+1C_n (n = 1 and 2), which can be prepared using the recently developed procedure of exfoliation of corresponding NBs from MAX phases, were examined within first principles calculations in comparison with parent MAX phases Ti₃AlC₂ and Ti₂AlC. We found that in general Ti_n+1C_n and Ti_n+1Al_0.5C_n NBs retain the atomic geometries of the corresponding blocks of the MAX phases, but some structural distortions for the NBs occur owing to the lowering of the coordination number for atoms in the external Ti sheets of the nano-block structures. Our analysis based on their cohesive and formation energies reveals that the stability of the nano-block structures increases with index n (or, in other words, with a growth of the number of Ti–C bonds), the Al-containing NBs becoming more stable than the “pure” Ti–C NBs. Our data show that the magnetization of the simulated planar nano-block structures can be expected; so, for the Ti₃C₂ nano-block the most stable will be the spin configuration, where within each external Ti sheet the spins are coupled ferromagnetically together with antiferromagnetic ordering between opposite external titanium sheets of this nano-block.     

A photoelectron spectroscopic study of the carburization of MoO3

MoO₃ and Mo samples containing copper were treated with different hydrocarbon/hydrogen gas mixtures. The formation of Mo₂C was followed by X-ray photoelectron spectroscopy (XPS). Spectra taken in the Mo 3d, C 1s, O 1s, Cu 2p and Cu KLL regions demonstrated that the treatment with the hydrocarbon/hydrogen gas mixtures led to the formation of Mo₂C. From the comparison of the effects of various hydrocarbons on the XP spectra of Mo 3d we can state that the reduction of MoO₃ starts at the lowest temperature for C₂H₆/H₂ (600 K) followed by CH₄/H₂ (700 K) and C₄H₁₀/H₂ (723 K). Binding energies of Mo 3d_5/2 characteristic for Mo₂C are measured in the range of 227.7-228.0 eV. These values were attained at 900 K for CH₄/H₂, at 800 K for C₂H₆/H₂ and at 873 K for C₄H₁₀/H₂. Addition of copper to MoO₃ catalyzed its reduction and promoted the carburization process.     

Exploring the mechanism of NO–C2H4 reactions on the surface of stepped Pt(3 3 2)

Fourier transform infra red reflection–absorption spectroscopy (FTIR-RAS), thermal desorption spectroscopy (TDS), and auger electron spectroscopy (AES), were employed to explore the mechanism of NO reduction in the presence of C₂H₄ on the surface of stepped Pt(3 3 2). Both NO–Pt and C₂H₄–Pt interactions are enhanced when NO and C₂H₄ are co-adsorbed on Pt(3 3 2). As a result, C₂H₄ is dissociated at surface temperatures as low as 150 K, and the N–O stretch band is weakened. The presence of post-exposed C₂H₄ leads NO desorption from steps to decrease significantly, but the same effect on NO desorption from terraces becomes appreciable only at higher post-exposures of C₂H₄, e.g., 0.6 L and 1.2 L, and proceeds to a much slighter extent. Auger spectra indicate that as a result of the reaction with O from NO dissociation, the amount of surface C species is greatly reduced when NO is post-exposed to a C₂H₄ adlayer. It is concluded that reduction of NO in the presence of C₂H₄ proceeds very effectively on the surface of the Pt(3 3 2), through a mechanism of NO dissociation and subsequent O removal. Following this mechanism, the significant dissociation of adsorbed NO molecules on steps at surface temperatures below 400 K, and subsequent rapid reaction between the resultant O and C-related species, accounts for the considerable amount of N₂ desorption at temperatures below 400 K.     

Influence of precipitant solution pH on the structural, morphological and upconversion luminescent properties of Lu2O3:2%Yb, 0.2%Tm nanopowders

Lutetium oxide nanopowders codoped with Tm³⁺ and Yb³⁺ were synthesized by the reverse-strike co-precipitation method. Effects of precipitant solution pH on the structural, morphological and upconversion luminescent properties of Lu₂O₃:2%Yb, 0.2%Tm nanopowders had been investigated. The results show that pH value of the precipitant (NH₄HCO₃) solution has a significant effect on the particle size, morphology and upconversion emission intensity of the Lu₂O₃:2%Yb, 0.2%Tm nanopowders. All the samples obtained from different pH value of precipitant solution can be readily indexed to pure cubic phase of Lu₂O₃, indicating good crystallinity. The upconversion emission intensity of Lu₂O₃:2%Yb, 0.2%Tm nanopowders obtained from the precipitant solution with pH=11 is the strongest. The enhancement of the upconversion luminescence is suggested to be the consequence of reducing the number of OH⁻ groups and the enlarged nanopowder size. The strong blue, weak red and near infrared emissions from the prepared nanopowders were observed under 980 nm laser excitation, and attributed to the ¹G₄→³H₆, ¹G₄→³F₄ and ³H₄→³H₆ transitions of Tm³⁺ ion, respectively.     

The bending triad of the quasi-spherical top molecule SO2F2 in the 550 cm region

The analysis of the ν₃/ν₇/ν₉ bending triad of SO₂F₂ has been recently performed with the Watson’s Hamiltonian up to octic terms employing 79 rovibrational parameters but including only the first order Coriolis interaction terms, fixed to ab initio values [H. Bürger, J. Demaison, F. Hegelund, L. Margulès, I. Merke, J. Mol. Struct. 612 (2002) 133-141]. Since SO₂F₂ is a quasi-spherical top, it can also be considered as derived from the sulfate ion. We have thus developed a new tensorial formalism in the O (3) ⊃ T_d ⊃ C_2v group chain [M. Rotger, V. Boudon, M. Loëte, J. Mol. Spectrosc. 216 (2002) 297-307]. This approach allows a systematic development of rovibrational interactions and makes global analyses easier to perform even for complex polyad systems. We present here an application of this model to the analysis of the bending triad, with the same set of microwave assignments and almost the same set of infrared assignments as in the previous study of Bürger et al. It appears that we need to expand our Hamiltonian to a lower degree than the “classical” one (six instead of eight) when including also the second order Coriolis interactions. Our fit does not include more parameters. Furthermore, all of them are determined and the standard deviation of the rotational transitions is twice smaller. The analysis has been performed thanks to the C_2v TDS program suite, which is freely available at the URL: http://www.u-bourgogne.fr/LPUB/c2vTDS.html.     

Promotion of surface SOx on the selective catalytic reduction of NO by hydrocarbons over Ag/Al2O3

The promotion of sulfur oxides on the selective catalytic reduction (SCR) of NO by hydrocarbons in the presence of a low concentration of sulfur oxides over Ag/Al₂O₃ has been investigated by a flow reaction test and in situ infrared spectroscopy. When the C₃H₆ (or C₁₀H₂₂) + NO + O₂ feed-flow reaction was tested, maximum NO reduction was below 30% over fresh Ag/Al₂O₃. After the addition of SO₂ to the feed flow, conversion increased slightly. Conversion increased further after SO₂ was cut-off from the feed flow. This demonstrated that the increase in NO reduction activity of the catalyst was related to SO_x adsorbed on the catalyst. SO_x adsorbed on the catalytic surface (1375 cm⁻¹) was detected by IR spectroscopy and was stable within the temperature range. NCO species, as an intermediate in NO reduction, on SO_x-adsorbed Ag/Al₂O₃ in a C₃H₆ + NO + O₂ feed flow was observed in in situ IR spectra during the elevation of the reaction temperature from 473 to 673 K, while it was only observed at 673 K on fresh Ag/Al₂O₃ under the same experimental conditions. We suggest that SO_x in low concentrations depressed the combustion of reductants by contaminating hydrocarbon combustion active sites on the catalyst, resulting in an increase in NO reduction efficiency of the reductants.     

Effect of additives for higher removal rate in lithium niobate chemical mechanical planarization

High roughness and a greater number of defects were created by lithium niobate (LN; LiNbO₃) processes such as traditional grinding and mechanical polishing (MP), should be decreased for manufacturing LN device. Therefore, an alternative process for gaining defect-free and smooth surface is needed. Chemical mechanical planarization (CMP) is suitable method in the LN process because it uses a combination approach consisting of chemical and mechanical effects. First of all, we investigated the LN CMP process using commercial slurry by changing various process conditions such as down pressure and relative velocity. However, the LN CMP process time using commercial slurry was long to gain a smooth surface because of lower material removal rate (MRR). So, to improve the material removal rate (MRR), the effects of additives such as oxidizer (hydrogen peroxide; H₂O₂) and complexing agent (citric acid; C₆H₈O₇) in a potassium hydroxide (KOH) based slurry, were investigated. The manufactured slurry consisting of H₂O₂-citric acid in the KOH based slurry shows that the MRR of the H₂O₂ at 2 wt% and the citric acid at 0.06 M was higher than the MRR for other conditions.     

X-ray photoelectron spectroscopy of nano-multilayered Zr-O/Al-O coatings deposited by cathodic vacuum arc plasma

Nano-multilayered Zr-O/Al-O coatings with alternating Zr-O and Al-O layers having a bi-layer period of 6-7 nm and total coating thickness of 1.0-1.2 μm were deposited using a cathodic vacuum arc plasma process on rotating Si substrates. Plasmas generated from two cathodes, Zr and Al, were deposited simultaneously in a mixture of Ar and O₂ background gases. The Zr-O/Al-O coatings, as well as bulk ZrO₂ and Al₂O₃ reference samples, were studied using X-ray photoelectron spectroscopy (XPS). The XPS spectra were analyzed on the surface and after sputtering with a 4 kV Ar⁺ ion gun. High resolution angle resolved spectra were obtained at three take-off angles: 15°, 45° and 75° relative to the sample surface.It was shown that preferential sputtering of oxygen took place during XPS of bulk reference ZrO₂ samples, producing ZrO and free Zr along with ZrO₂ in the XPS spectra. In contrast, no preferential sputtering was observed with Al₂O₃ reference samples. The Zr-O/Al-O coatings contained a large amount of free metals along with their oxides. Free Zr and Al were observed in the coating spectra both before and after sputtering, and thus cannot be due solely to preferential sputtering.Transmission electron microscopy revealed that the Zr-O/Al-O coatings had a nano-multilayered structure with well distinguished alternating layers. However, both of the alternating layers of the coating contained of a mixture of aluminum and zirconium oxides and free Al and Zr metals. The concentration of Zr and Al changed periodically with distance normal to the coating surface: the Zr maximum coincided with the Al minimum and vice versa. However the concentration of Zr in both alternating layers was significantly larger than that of Al. Despite the large free metal concentration, the Knoop hardness, 21.5 GPa, was relatively high, which might be attributed to super-lattice formation or formation of a metal-oxide nanocomposite within the layers.     

Experimental and kinetic modeling study of C2H4 oxidation at high pressure

A detailed chemical kinetic model for oxidation of C₂H₄ in the intermediate temperature range and high pressure has been developed and validated experimentally. New ab initio calculations and RRKM analysis of the important C₂H₃ + O₂ reaction was used to obtain rate coefficients over a wide range of conditions (0.003-100 bar, 200-3000 K). The results indicate that at 60 bar and medium temperatures vinyl peroxide, rather than CH₂O and HCO, is the dominant product. The experiments, involving C₂H₄/O₂ mixtures diluted in N₂, were carried out in a high pressure flow reactor at 600-900 K and 60 bar, varying the reaction stoichiometry from very lean to fuel-rich conditions. Model predictions are generally satisfactory. The governing reaction mechanisms are outlined based on calculations with the kinetic model. Under the investigated conditions the oxidation pathways for C₂H₄ are more complex than those prevailing at higher temperatures and lower pressures. The major differences are the importance of the hydroxyethyl (CH₂CH₂OH) and 2-hydroperoxyethyl (CH₂CH₂OOH) radicals, formed from addition of OH and HO₂ to C₂H₄, and vinyl peroxide, formed from C₂H₃ + O₂. Hydroxyethyl is oxidized through the peroxide HOCH₂CH₂OO (lean conditions) or through ethenol (low O₂ concentration), while 2-hydroperoxyethyl is converted through oxirane.     

Flame structure studies of rich ethylene-oxygen-argon mixtures doped with CO2, or with NH3, or with H2O

Structures of several premixed ethylene-oxygen-argon rich flat flames burning at 50 mbar have been established by using molecular beam mass spectrometry in order to investigate the effect of CO₂, or NH₃, or H₂O addition on species concentration profiles. The aim of this study is to examine the eventual changes of profiles of detected hydrocarbon intermediates which could be considered as soot precursors (C₂H₂, C₄H₂, C₅H₄, C₅H₆, C₆H₂, C₆H₄, C₆H₆, C₇H₈, C₆H₆O, C₈H₆, C₈H₈, C₉H₈ and C₁₀H₈). The comparative study has been achieved on four flames with an equivalence ratio (f) of 2.50: one without any additive (F2.50), one with 15% of CO₂ replacing the same quantity of argon (F2.50C), one with 3.3% of NH₃ in partial replacement of argon (F2.50N) and one with 13% of H₂O in replacement of the same quantity of argon (F2.50H). The four flat flames have similar final flame temperatures (1800 K).CO₂, or NH₃, or H₂O addition to the fresh gas inlet causes a shift downstream of the flame front and thus flame inhibition. Endothermic processes CO₂ + H = CO + OH and H₂O + H = H₂ + OH are responsible of the reduction of the hydrocarbon intermediates in the CO₂ and H₂O added flames through the supplementary formation of hydroxyl radicals. It has been demonstrated that such processes begin to play at the end of the flame front and becomes more efficient in the burnt gases region.The replacement of some Ar by NH₃ is responsible only for a slight decrease of the maximum mole fraction of C₂H₂, but NH₃ becomes much more efficient for C₄H₂ and C₅ to C₁₀ species. Moreover, the efficiency of NH₃ as a reducing agent of C₅ to C₁₀ intermediates is larger than that of CO₂ and H₂O for equal quantities added.     

Characterization of mesoporous VOx/MCM-41 composite materials obtained via post-synthesis impregnation

Spherical-particle MCM-41 was synthesized at room temperature, and, then, impregnated with aqueous solutions of NH₄VO₃ to produce variously loaded VO_x/MCM-41 composite materials. Bulk and surface properties of the materials thus produced were characterized by means of X-ray powder diffractometry (XRD), infrared spectroscopy (FTIR), N₂ sorptiometry and X-ray photoelectron spectroscopy (XPS). Results obtained indicated that subsequent calcination at 550 °C (for 2 h) of the blank and impregnated MCM-41 particles, results in materials assuming the same bulk structure of MCM-41, and exposing uniformly mesporous, high area surfaces (P_w = 2.0-2.3 nm; 974-829 m²/g), except for the material obtained at 20 wt%-V₂O₅ that was shown to suffer a considerable loss on surface area (down to 503 m²/g). XPS results implied that the immobilization of the VO_x species occurs via interaction with surface OH/H₂O groups of MCM-41, leading to the formation of vanadate (VO₃⁻) surface species, as well as minor V-O-Si and V₂O₅-like species. However, in all cases, the vanadium sites remained pentavalent and exposed on the surface.     

Structural and cathodoluminiscent properties of Zr0.95Ce0.05O2 nanopowders prepared by sol-gel and template methods

Nanopowders of Zr_0.95Ce_0.05O₂ composition have been prepared by a standard Pechini-type sol-gel process and by means of a colloidal crystal template approach. In the latter method, inverse opal Zr_0.95Ce_0.05O₂ powders were fabricated employing poly(methyl methacrylate) (PMMA) colloidal crystals as a template. The effects of the two different synthesis routes on the structure and microstructural characteristics of the prepared nanopowders were evaluated by X-ray diffraction and scanning electron microscopy. For both preparation routes, the X-ray diffraction analysis has shown that a tetragonal fluorite structure is formed with a crystallite size of ∼35-40 nm. The scanning electron microscopy measurements indicate that the powder obtained by the sol-gel Pechini-type process is comprised of nanoparticles that are arranged in agglomerates with shape and size relatively uniform whereas the inverse opal Zr_0.95Ce_0.05O₂ nanopowders exhibit the formation of macropores with a mean size of ∼100 nm. The cathodoluminescence spectra of the prepared Zr_0.95Ce_0.05O₂ nanomaterials have been measured in the 300-800 nm wavelength range. The powder prepared by sol-gel method yields a broad emission band centered at 482 nm whereas the emission from the inverse opal preparation is considerably less intense.     

The n-butyl amine TPD measurement of Brönsted acidity for solid catalysts by simultaneous TG/DTG-DTA

The method for Brönsted acidity measurement based on TPD of alkyl amines desorption by gas-chromatography or thermogravimetry was adapted for simultaneous TG/DTG-DTA analysis. The acidity measurements were focused on the 12-tungstophosphoric acid (H₃PW₁₂O₄₀) and its salts, especially with Cesium since these posses the highest Brönsted acidity and they are among the most interesting catalysts. The n-butyl amine (NBA) desorption takes place in three steps for Cs_xH_3−xPW₁₂O₄₀, x = 0-2, and four steps for the Cs_2.5H_0.5PW₁₂O₄₀. The steps of desorption correspond to the release of NBA molecules in stages, as NBA or butene molecules resulted from the Hofmann elimination reaction and NH₃ + H₂O formed by decomposition of ammonium salt. The quantities of desorption products, C₄H₈ and NH₃ + H₂O, corresponding to the stages with the maximum desorption rates at 400-420 °C, respectively 560-600 °C, are in the stoichiometric ratio with the Brönsted acidity.     

Catalytic effect of water,water dimer,water trimer,HCOOH, H2SO4, CH3CH2COOH and HN(NO2)2 on the isomerisation of HN(NO2)2 to O2NNN(O)OH: a mechanism study

In this article, the isomerisation mechanisms of HN(NO₂)₂ to O₂NNN(O)OH without and with catalyst X (X = H₂O, (H₂O)₂, (H₂O)₃, HCOOH, H₂SO₄, CH₃CH₂COOH and HN(NO₂)₂) have been investigated theoretically at the CBS-QB3 level of theory. Our results show that the catalyst X (X = H₂O, (H₂O)₂, (H₂O)₃, HCOOH, H₂SO₄ and CH₃CH₂COOH) shows different positive catalytic effects on reducing the apparent activation energy of the isomerisation reaction processes. Such different catalytic effects are mainly related to the number of hydrogen bonds and the size of the ring structure in X (X = H₂O, (H₂O)₂ and (H₂O)₃)-assisted transition states, as well as different values of pK_a for H₂SO₄, HCOOH and CH₃CH₂COOH. Very interesting is also the fact that H₂SO₄-assisted reaction is the most favourable for the hydrogen transfer from HN(NO₂)₂ to O₂NNN(O)OH, due to the smallest pK_a (?3.0) value of H₂SO₄ than H₂O, HCOOH, H₂SO₄ and CH₃CH₂COOH, and also because of the largest ∠X???H???Y (the angle between the hydrogen bond donor and acceptor) involved in H₂SO₄-assisted transition state. Compared to the self-catalysis of the isomerisation mechanisms of HN(NO₂)₂ to O₂NNN(O)OH, the apparent activation energy of H₂SO₄-assisted channel also reduces by 9.6 kcal?mol^?1, indicating that H₂SO₄ can affect the isomerisation of HN(NO₂)₂ to O₂NNN(O)OH, most obvious among all the catalysts H₂O, (H₂O)₂, (H₂O)₃, HCOOH, H₂SO₄, CH₃CH₂COOH and HN(NO₂)₂.     

Formation of α-Si1−xCx:H and nc-SiC films grown by HWCVD under different process pressure

In this work, hydrogenated amorphous silicon carbide (α-Si_1−xC_x:H) and nanocrystalline SiC (nc-SiC) thin films were deposited by hot wire CVD (HWCVD) using SiH₄/C₂H₂/H₂ gas mixtures. It was found that the films prepared under low gas pressure were α-Si_1−xC_x:H and those prepared under high gas pressure were nc-3C-SiC. The α-Si_1−xC_x:H films showed enhanced density of C-H_n and Si-C bonds with increasing C₂H₂ fraction, which induced an increase in optical gap from 1.8 to 3.0 eV. For the deposition process of nc-SiC, the E_g opt of the deposited films varied from 1.9 eV to 2.5 eV as the filament temperature increased from 1700 to 2100 °C. The deposition rate decreased rapidly from 5.74 nm/min to 0.8 nm/min with increasing T_F.