Preconcentration speciation method for mercury compounds in water samples using solid phase extraction followed by reversed phase high performance liquid chromatography

A simple and rapid method for in situ preconcentration of inorganic and organic mercury compounds in water samples, based on solid phase extraction using dithizone immobilised on a reversed-phase C18 cartridge, has been developed. The adsorbed complexes were stable on the cartridge for at least 2 weeks. The speciation analysis of methylmercury (MeHg), phenylmercury (PhHg) and inorganic mercury (Hg (II)) were done by reversed-phase high performance liquid chromatography. The calibration graphs of MeHg, PhHg and Hg (II) were linear (r>0.999) from the detection limits (0.58, 0.66 and 0.54 ng) to 38, 25 and 26 ng of Hg, respectively. The average recoveries of MeHg, PhHg and Hg (II) from spiked samples (0.3-48.0 mug l(-1) Hg) were 98+/-3, 99+/-1 and 100+/-7%, respectively. By applying SPE procedure a 200-fold concentration of the sample was obtained.     

Non-chromatographic speciation analysis of mercury by flow injection on-line preconcentration in combination with chemical vapor generation atomic fluorescence spectrometry

A novel non-chromatographic approach for direct speciation of mercury, based on the selective retention inorganic mercury and methylmercury on the inner wall of a knotted reactor by using ammonium diethyl dithiophosphate and dithizone as complexing agents respectively, was developed for flow injection on-line sorption preconcentration coupled with chemical vapor generation non-dispersive atomic fluorescence spectrometry. With the sample pH kept at 2.0, the preconcentration of inorganic mercury on the inner walls of the knotted reactor was carried out based on the exclusive retention of Hg–DDP complex in the presence of methylmercury via on-line merging the sample solution with ammonium diethyl dithiophosphate solution, and selective preconcentration methylmercury was achieved with dithizone instead of ammonium diethyl dithiophosphate. A 15% (v/v) HCl was introduced to elute the retained mercury species and merge with KBH₄ solution for atomic fluorescence spectrometry detection. Under the optimal experimental conditions, the sample throughputs of inorganic mercury and methylmercury were 30 and 20 h^− 1 with the enhancement factors of 13 and 24. The detection limits were found to be 3.6 ng l^− 1 for Hg²⁺ and 2.0 ng l^− 1 for CH₃Hg⁺. The precisions (RSD) for the 11 replicate measurements of each 0.2 μg l^− 1 of Hg²⁺ and CH₃Hg⁺ were 2.2% and 2.8%, respectively. The developed method was validated by the analysis of certified reference materials (simulated natural water, rice flour and pork) and by recovery measurements on spiked samples, and was applied to the determination of inorganic mercury and methylmercury in biological and environmental water samples.     

On-line coupling of flow injection displacement sorption preconcentration to high-performance liquid chromatography for speciation analysis of mercury in seafood

A simple and cost-effective method for speciation analysis of trace mercury in seafood was developed by on-line coupling flow injection microcolumn displacement sorption preconcentration to high-performance liquid chromatography (HPLC) with UV detection. The methodology involved the presorption of the Cu-PDC (pyrrolidine dithiocarbamate) chelate onto a microcolumn packed with a cigarette filter sorbent, simultaneous preconcentration of Hg(II), methylmercury (MeHg), ethylmercury (EtHg), and phenylmercury (PhHg) onto the microcolumn through a displacement reaction with the presorbed Cu-PDC, and their subsequent elution from the microcolumn for on-line HPLC separation. Interferences from heavy metal ions with lower stability of their PDC chelates relative to Cu-PDC were minimized without the need of any masking agents. With the consumption of 4.0 ml of sample solution, the enrichment factors were about 80. The detection limits were 10-25 ng g(-1) (as Hg) in fresh tissue. Precision (R.S.D. (%), n = 5) ranged from 2 to 3% at the 500 microg l(-1) (as Hg) level. The developed technique was validated by analyzing a certified reference material (DORM-2, dogfish-muscle), and was shown to be useful for mercury speciation in real seafood samples.     

Rapid sequential determination of inorganic mercury and methylmercury in natural waters by flow injection-cold vapour-atomic fluorescence spectrometry

A novel method for the rapid sequential determination of inorganic mercury and methylmercury in natural waters at the ng/l. level has been developed. Trace enrichment and separation of mercury species are achieved using a microcolumn of sulphydryl cotton which has a relatively high affinity for methylmercury. The limit of detection for methylmercury based on processing of a 0.5-ml sample volume was 6 ng/l. Application to river waters is demonstrated.     

Reversed-phase partition high-pressure liquid chromatography of trace amounts of inorganic and organic mercury with silver diethyldithiocarbamate

Inorganic and organic mercury diethyldithiocarbamates have been separated by reversedphase partition high-pressure liquid chromatography. The mercury chelates were formed by an exchange reaction with silver diethyldithiocarbamate in chloroform, in the presence of acetate buffer (pH 5.0). The inorganic and organic mercury chelates in the extract were separated within 30 min on a 3.9 x 300 mm mu-Bondapak C(18) column. EDTA (10(-4)M) in methanol-water mixture (78:22 v v ) was used as eluent at a flow-rate of 0.5 ml min .     

Determination of methylmercury and inorganic mercury in water samples by slurry sampling cold vapor atomic absorption spectrometry in a flow injection system after preconcentration on silica C18 modified

A novel method for preconcentration of methylmercury and inorganic mercury from water samples was developed involving the determination of ng l⁻¹ levels of analytes retained on the silica C₁₈ solid sorbent, previous complexation with ammonium pyrrolidine dithiocarbamate (APDC), by slurry sampling cold vapor atomic absorption spectrometry (SS-CVAAS) in a flow injection (FI) system. Several variables were optimized affecting either the retention of both mercury species, such as APDC concentration, silica C₁₈ amount, agitation times, or their determination, including hydrochloric acid concentration in the suspension medium, peristaltic pump speed and argon flow-rate. A Plackett-Burman saturated factorial design permitted to differentiate the influential parameters on the preconcentration efficiency, which were after optimized by the sequential simplex method. The contact time between mercury containing solution and APDC, required to reach an efficient sorption, was decreased from 26 to 3 min by the use of sonication stirring instead of magnetic stirring. The use of 1 mol dm⁻³ hydrochloric acid suspension medium and 0.75% (m/v) sodium borohydride reducing agent permitted the selective determination of methylmercury. The combination of 5 mol dm⁻³ hydrochloric acid and 10⁻⁴% (m/v) sodium borohydride was used for the selective determination of inorganic mercury. The detection limits achieved for methylmercury and inorganic mercury determination under optimum conditions were 0.96 and 0.25 ng l⁻¹, respectively. The reliability of the proposed method for the determination of both mercury species in waters was checked by the analysis of samples spiked with known concentrations of methylmercury and inorganic mercury; quantitative recoveries were obtained.     

Determination of mercury species in natural waters at picogram level with on-line RP C18 preconcentration and HPLC-UV-PCO-CVAAS

A new technique has been developed for the determination of methyl-, ethyl-, methoxyethyl-, ethoxyethyl-, phenyl- and inorganic mercury in natural water samples. The mercury compounds have been complexed for the preconcentration on RP C18 columns by sodium pyrrolidinedithiocarbamate (SPDC), sodium diethyldithiocarbamate (SDDC) and hexamethyleneammonium (HMA) — hexamethylenedithiocarbamate (HMDC), separated by HPLC and determined by UV-PCO-CVAAS (ultra violet, post column oxidation, cold vapour atomic absorption spectrometry). The standard deviations are in the range of 6.9 to 11.8%. The recoveries amount to 86%, 78%, 88%, 83%, 79% and 84% for methyl-, ethyl-, methoxyethyl-, ethoxyethyl-, phenyl- and inorganic mercury for the enrichment from 300 ml water samples. The detection limit for methyl mercury is 0.5 ppt. This new on-line preconcentration procedure has been tested with rain, drinking, surface and process water samples.     

Microcolumn preconcentration and gas chromatography-microwave induced plasma-atomic emission spectrometry (GC-MIP-AES) for mercury speciation in waters

A novel method for the direct determination of mercury species at the ng l^–1 level in natural waters is described. Methyl-, ethyl- and inorganic mercury are preconcentrated on a sulphhydryl cotton microcolumn incorporated in a flow injection system. Retained mercury species are then eluted with hydrochloric acid solution (3 mol/l) and subjected to phenylation before determination by gas chromatography-microwave induced plasma-atomic emission spectrometry. Limits of detection for mercury species are 10 ng l^–1 for methyl- and ethyl-mercury and 16 ng l^–1 for inorganic mercury based on processing 200 ml of sample. Application of the methodology to waters of the Manchester Ship Canal revealed elevated levels of methylmercury and inorganic mercury.     

Determination of total and methyl mercury in human permanent healthy teeth by electrothermal atomic absorption spectrometry after extraction in organic phase

A simple and sensitive method has been developed for determination of inorganic and methyl mercury in biological samples by ETAAS. For determination of methyl mercury; it was transferred to toluene phase by acid leaching extraction method. For total mercury after digestion of samples; it was extracted to toluene phase by means of the chelating agent diethyldithiocarbamate. Formation of complex between MeHg and diethyldithiocarbamate enhance the MeHg signal and increases the reproducibility. Furthermore, Pd-DDC was used as modifier for both mercury and methyl mercury determinations. The optimization performance was independently carried out by modifying the parameters such as temperature of mineralization, atomization and gas flow rate for methylmercury and inorganic mercury in ETAAS. The limits of detection were 0.15 and 0.12 μg g⁻¹ for methyl mercury and total mercury, respectively. The repeatability of the measurements of whole procedure were 15.8% for methyl mercury and 16.9% for total mercury determination. The accuracy of the method has been investigated by means of spiking different amounts of methylmercury and inorganic mercury to the samples. The recoveries were found within the range of 88-95% for methyl mercury and 85-92% for total mercury. For determination of total mercury, the method was validated by CVAAS. The obtained results by the present procedure were in good agreement with those of the CVAAS. The proposed method was applied for 30 human permanent healthy teeth (without filling) which significant positive correlations were found among number of amalgam filling and total mercury and MeHg.     

Determination of organic and inorganic mercury compounds by reverse-phase high-performance liquid chromatography after extraction of the compounds as their dithizonates

A sensitive and selective method is described for the simultaneous determination of inorganic and organic mercury compounds. The mercury compounds are extracted into toluene or chloroform with dithizone, and the dithizonates are separated by liquid chromatography on an ODS column. Complete resolution was obtained between methylethyl-, phenyl- and inorganic mercury with a mobile phase of THF/methanol (2:1) with 0.05 M acetate buffer pH 4 (62 + 38), containing 50 μM EDTA. The mercury chelates were detected spectrophotometrically at 475 nm. The detection limits were at the subnanogram level. The method is applicable to human urine, tap water and tomatoes.     

Preconcentration of phenlymercury,methylmercury and inorganic mercury from natural waters with diethylammonium diethyldithiocarbamate-loaded polyurethane foam

The percentage extraction of organomercurials and inorganic mercury on polyurethane foam loaded with diethylammonium diethyldithiocarbamate is high over a wide pH range, particularly when a plasticizer is added to the foam. Flow rates up to 120 ml min^-1 give quantitative extraction of inorganic mercury. Mercury(II), methylmercury and phenylmercury ions at 1 μg l^-1 levels can be almost quantitatively preconcentrated from tap and saline water, and eluted from the foam with acetone.     

Determination of ultra-trace amount methyl-, phenyl- and inorganic mercury in environmental and biological samples by liquid chromatography with inductively coupled plasma mass spectrometry after cloud point extraction preconcentration

The cloud point extraction (CPE) preconcentration of ultra-trace amount of mercury species prior to reverse-phase high performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS) detection was studied. Mercury species including methyl-, ethyl-, phenyl- and inorganic mercury were transformed into hydrophobic chelates by reaction with sodium diethyldithiocarbamate, and the hydrophobic chelates were extracted into a surfactant-rich phase of Triton X-114 upon heating in a water bath at 40 °C. Ethylmercury was found partially decomposed during the CPE process, and was not included in the developed method. Various experimental conditions affecting the CPE preconcentration, HPLC separation, and ICP-MS determination were optimized. Under the optimized conditions, detection limits of 13, 8 and 6 ng l⁻¹ (as Hg) were achieved for MeHg⁺, PhHg⁺ and Hg²⁺, respectively. Seven determinations of a standard solution containing the three mercury species each at 0.5 ng ml⁻¹ level produced relative standard deviations of 5.3, 2.3 and 4.4% for MeHg⁺, PhHg⁺ and Hg²⁺, respectively. The developed method was successfully applied for the determination of the three mercury species in environmental water samples and biological samples of human hair and ocean fish.     

Tandem focused ultrasound (TFU) combined with fast furnace analysis as an improved methodology for total mercury determination in human urine by electrothermal-atomic absorption spectrometry

A new sample preparation procedure based on tandem (that is, different diameter probe sonicators used in the same sample treatment) focused ultrasound (TFU) for mercury separation, preconcentration and back-extraction in aqueous solution from human urine has been developed. The urine is first oxidized with KMnO₄/HCl/focused ultrasound (6 mm probe). Secondly, the mercury is extracted and preconcentrated with dithizone and cyclohexane. Finally, the mercury is back-extracted and preconcentrated again with the aid of focused ultrasound (3 mm probe). The procedure allows determining mercury by electrothermal atomic absorption spectrometry with fast furnace analysis and calibration against aqueous standards. Matrix modification is provided by the chemicals used in the sample treatment. The procedure is accomplished with low sample volume (8.5 ml). Low volume and low concentration reagents are used. The sample treatment is rapid (less than 3 min per sample) and avoids the use of organic phase in the graphite furnace. The preconcentration factor used in this work was 14. The limit of detection and the limit of quantification in urine were, respectively, 0.27 and 0.9 μg l⁻¹. The relative standard deviation of aqueous standards (n=10) was 4% for a concentration of 100 μg l⁻¹ and 5% for a concentration of 400 μg l⁻¹. Recoveries from spiked urine with inorganic mercury, methyl-mercury, phenyl-mercury and diphenyl-mercury ranged from 86 to 98%.     

Voltammetric quantification and speciation of mercury compounds

The use of a carbon paste electrode modified with a thiolic resin for the determination of inorganic mercury and organomercury compounds, present simultaneously in a sample, is described. The compounds are first preconcentrated at the electrode surface by means of a purely chemical reaction with the modifier on the electrode surface. The high affinity of the modifier for the mercury compounds ensures low limits of detection and determination. Differentiation between several mercury species is possible by control of the reduction potential applied to the working electrode. This selective reduction results in the formation of atomic mercury at the electrode surface which can be determined with a very high sensitivity by means of its re-oxidation wave in cyclic voltammetry. Optimization of the instrumental parameters and evidence for the reduction processes are discussed. Analysis of inorganic mercury in the presence of methylmercury, with a detection limit of 4 μg Hg 1⁻¹, and of methylmercury in the presence of inorganic mercury, with a detection limit of 2 μg Hg 1⁻¹, is described in detail. In both cases the preconcentration time is 6 min. Other organomercury species can also be quantified. Application of the method to environmental aquatic samples is discussed.     

Flame AAS determination of lead in water with flow-injection preconcentration and speciation using functionalized cellulose sorbent

The on-line solid phase extraction of trace amount of lead in flow-injection system with flame AAS detection was investigated using cellulose sorbents with phosphonic acid and carboxymethyl groups, C(18) sorbent non-modified and modified with Pyrocatechol Violet or 8-quinolinol, commercial chelating sorbents Chelex 100 and Spheron Oxin 1000, non-polar sorbent Amberlite XAD-2 modified with Pyrocatechol Violet and several cation-exchange resins. The best dynamic characteristics of retention were observed for functionalized cellulose sorbents. For Cellex P assumed as optimum sorbent, elution with a separate fractions of nitric acid and ethanol allows the differentiation between tetraalkyllead and sum of inorganic lead and organolead species of smaller number of alkyl groups. The detection limit for the determination of inorganic Pb(II) was estimated as 0.17 microg/l. at preconcentration from 50 ml sample at a flow rate of 7 ml/min.     

Preconcentration of inorganic mercury and organic mercury with solvent extraction for neutron activation analysis

A preconcentration method combined with neutron activation technique for the analysis of organic and inorganic mercury in waste water samples at ppb levels is presented. The inorganic mercury is extracted in CCl₄ solution with lead diethyldithiocarbamate reagent and the organic mercury is extracted in C₆H₆ solution. Interfering activities of sodium and bromine are removed from the irradiated samples by this procedure. Two different solvent extraction procedures are also described in detail.     

Determination of methylmercury in natural waters at the sub-nanograms per litre level by capillary gas chromatography after adsorbent preconcentration

Methylmercury was preconcentrated from water on to a sulph-hydryl cotton fibre adsorbent, using the column technique or the batch-column two-stage technique. A small volume of 2 M HCl was used to elute methylmercury and to separate it from inorganic mercury; 0.4–0.6 ml of benzene was used to extract methylmercury from the eluate. Analysis was performed by capillary gas chromatography with electron-capture detection. The detection limit for methylmercury was <0.05 ng l^?1 in a 4-l water sample. Four surface waters were analysed to test the agreement of methylmercury concentration between the two preconcentration methods, and to test the interference of humic substances on the filtered and unfiltered surface water. The methylmercury concentrations found in different surface water samples ranged from 0.08 to 0.48 ng l^?1.     

Analysis of mercury(II), methylmercury and phenylmercury by RPHPLC with micellized dithizone post-column derivatization photometric detection

Post-column derivatization detection system based on dithizone solubilized in cetyltrimethyl-ammonium hydrogenesulfate micellar media at pH 2.0 was devised and evaluated for selective detection of mercury(II), methylmercury and phenylmercury in reversed-phase HPLC system with photometric detection at 500 nm. This reagent solution is fully compatible with acidic organo-aqueous mobile phases generally used in RPHPLC. With the aid of the detection systematic study of the retention behaviour of three mercury species on octadecylsilica sorbent was carried out. Influence of pH, acetonitrile volume fraction, complex forming additives was investigated in detail. In mobile phase consisting of 5–30% of acetonitrile in water at pH 2.0 and 2·10^–4 mol·I^–1 DCTA linear calibration curves were measured in range 20–1000 ppb with correlation coefficient better than 0.99. Detection limits were 1–5 ng for this three mercury species. Interferences of copper(II) and silver(I) are negligible.     

Uses of 5-Methylresorcin-bonded polyurethan foam as a new solid phase extractor for the selective separation of mercury ions from natural water samples

In this work, 5-Methylresorcin (MR) bonded to untreated polyurethane foam (PUF) was successfully employed as a sorbent (MR-PUF) for the selective separation and determination of mercury in natural water samples. Mercury can be quantitatively recovered in the pH range of 5-7. The system presented a minicolumn packed with the new sorbent, where the sample solution was passed through it for a period of time and an eluent solution stripped out the retained mercury, which was further determined with dithizone. The new matrix was characterized by using different tools (IR spectra, stability and density). The kinetics of mercury uptake by the new matrix was found to be fast, reaching equilibrium in 20 minutes. A preconcentration factor of 350 was achieved. The proposed preconcentration procedure was applied successfully to the selective separation and determination of trace mercury in natural water samples.      

Speciation analysis of mercury in water samples by cold vapor atomic absorption spectrometry after preconcentration with dithizone immobilized on microcrystalline naphthalene

Trace amounts of inorganic mercury (Hg²⁺) and methylmercury cations (MeHg²⁺) were adsorbed quantitatively from acidic aqueous solution onto a column packed with immobilized dithizone on microcrystalline naphthalene. The trapped mercury was eluted with 10 ml of 7 mol L^–1 hydrochloric acid solution. The Hg²⁺ was then directly reduced with tin (II) chloride, and volatilized mercury was determined by cold vapor atomic absorption spectrometry (CVAAS). Total mercury (Hgt) was determined after decomposition of MeHg⁺ into Hg²⁺. Hg²⁺ and MeHg⁺ cations were completely recovered from the water with a preconcentration factor of 200. The relative standard deviation obtained for eight replicate determinations at a concentration of 0.3 g L^–1 was 1.8%. The procedure was applied to analysis of water samples, and the accuracy was assessed via recovery experiment.