Study of the reaction between 1,5-naphtalene diisocyanate and polycaprolactone in different solvents

The reaction between polycaprolactone and 1,5-naphtalene diisocyanate has been investigated in solvents with different dielectric constants and hydrogen bonding powers (toluene, ethyl acetate, ethyl methyl ketone), and in the same solvents with the addition of a catalytic amount of dimethyl sulfoxide (DMSO). The reaction was considered to proceed over two steps, the reaction of the first NCO group being faster. The course of the reaction was measured by titration of the unreacted NCO groups, ¹H- and ¹³C-NMR spectroscopy, and size exclusion chromatography. By titration only the overall reaction order and reaction rate constants could be determined. DMSO accelerated the reaction in all three solvents, which was explained by the stabilization of the activation complex by DMSO. Both steps of the reaction could be specified by NMR spectroscopy. The ratio between the reaction rate constants for the first and the second step decreased with the increased hydrogen bonding strength of the solvent and with DMSO. By SEC only the reaction of the first NCO group could be determined due to the low resolution for higher molar mass reaction products with a broad distribution. The values obtained for the first step reaction rate constants were in good agreement with NMR values. © 1995 John Wiley & Sons, Inc.     

Anionic graft polymerization and homopolymerization of phenyl glycidyl ether

Phenyl glycidyl ether was found to react with potassium starch alkoxide in dimethyl sulfoxide (DMSO) to give graft polymers in almost quantitative yields, both the monomer and the starch being incorporated completely into the graft polymer. No transfer reactions to monomer or solvent leading to homopolymerization was found. For this reason this system was used as a model for the study of the rate of the graft polymerization of alkylene oxides on starch and other carbohydrates. Comparison of the rates of the graft polymerization of phenyl glycidyl ether on starch alkoxide with that of the homopolymerization by potassium naphthalene in DMSO under comparable conditions showed that the former reaction was much slower. Rates of the graft polymerizations on dextrin and sucrose under comparable conditions, were similar to those obtained with starch. On the other hand, the rates of polymerization on poly(ethylene oxide) alkoxides of different molecular weights were similar to those obtained in the corresponding homopolymerization by potassium naphthalene, showing that neither the molecular weight of the initiator nor the viscosity of the reaction medium were the governing factors. This suggested that the lower rates obtained by using the carbohydrate alkoxides as initiators were connected with the heterogeneity of these reaction systems, the polymeric alkoxide being insoluble in DMSO. The systematic study carried out on the homopolymerization by potassium naphthalene in DMSO showed that the effective initiator was dimsyl anion obtained by interaction of potassium naphthalene with DMSO. The reaction was bimolecular, being first order to monomer and to initiator. The molecular weights increased with increasing monomer concentration and decreasing catalyst concentration, in accordance with a “living” polymerization system.     

Micelle‐catalyzed reaction of ninhydrin with DL‐valine in the absence and presence of organic solvents

Kinetics of the DL ‐valine‐ninhydrin reaction has been studied spectrophotometrically under varying conditions of [CTAB], [ninhydrin], [DL ‐valine], pH, temperature, and %(v/v) organic solvents (solvents used: 1‐propanol, methylcellosolve, acetonitrile, and dimethyl sulfoxide). Addition of CTAB and increase in the proportion of organic solvents, both showed catalyzing effect on the reaction. The effect of simultaneous presence of CTAB and DMSO in the reaction mixture has also been seen. The rate profiles obtained for solutions containing from 10% to 70% DMSO exhibited clear maxima that shifted progressively to higher concentrations of CTAB. The experimental results are explained in terms of specific solvent effects and the formation of stoichiometric hydrate DMSO · 2H₂O and the inhibitory effect of DMSO on micelle formation. © 2006 Wiley Periodicals, Inc. Int J Chem Kinet 38: 634–642, 2006     

DEVELOPMENT OF A CATALYST FOR SOLUTION OF POLY(VINYL ALCOHOL) IN NON-AQUEOUS MEDIUM

Chloro ethane dimethyl sulfoxide,C_2H_5Cl·DMSO(ECI·DMSO)was prepared by interaction of acrylic acid with conc.Hydrochloric acid in dimethyl sulfoxide(DMSO)and subsequent decarboxylation with H_2O_2 solution.The formation of the compound was confirmed by spectral and analytical methods;the molecular weight was determined by cryoscopic method.The solubility of poly(vinyl alcohol)(PVA)in different solvents or mixed solvents at 40℃,50℃and 60℃temperature in the presence of 0.01% of EC1·-DMSO was determined.It...     

Cadmium(II) for zinc(II) exchange reactions in deutero- and hematoporphyrin complexes in dimethyl sulfoxide

The metal-exchange reaction between Cd-deuteroporphyrin or Cd-ematoporphyrin and ZnCl₂ in dimethyl sulfoxide (DMSO) was studied spectrophotometrically. The order and activation parameters of the reaction of Cd²⁺ replacement by zinc ions were calculated. A mechanism of this reaction is suggested. The results are compared with the available data on metal-exchange reactions between Cd-mesoporphyrin and Cdprotoporphyrin and ZnCl₂ in DMSO.     

溶剂对自组装单分子膜电化学行为的影响

用循环伏安法、交流阻抗分析和STM研究了溶剂对自组装单分子膜电化学行为的影响.讨论了以丙酮、二甲基亚砜、乙醇、二甲基甲酰胺和水为溶剂制备的4-羟基-6-甲基-2-巯基嘧啶(HMMP)自组装单分子膜对抗坏血酸(AA)、多巴胺(DA)的电化学行为.结果表明,不同溶剂下制备的单分子膜对AA和DA的催化氧化表现出截然不同的行为;交流阻抗分析定量得出HMMP(丙酮)/Au电极与HMMP(二甲基亚砜)/Au电极的交换电流密度分别为1.14μA/cm²和2.04μA/cm²,电极表面覆盖度分别为93.2%和96.2%,STM图象显示出以丙酮和二甲基亚砜为溶剂制备的单分子膜具有不同的致密性和有序性.     

The thermodynamic properties of solutions of L-ascorbic acid in dimethyl sulfoxide and water-dimethyl sulfoxide mixtures

Solutions of L-ascorbic acid (AA) in dimethyl sulfoxide (DMSO) and DMSO-water mixtures were studied by the densitometry, surface tension, and calorimetry methods. The apparent and partial molar volumes of AA in solutions at 298.15 K were calculated. Surface tension insignificantly increased as the concentration of AA in DMSO grew. The enthalpies of solution of AA in the solvents and the enthalpies of transfer of AA from water into DMSO and DMSO-water mixed solvents were calculated. The results obtained were explained by the existence of H-bonds between AA and DMSO molecules.     

Preparation of no-carrier added 16-131I-hexadecanoic acid via halogen exchange: Comparison between two methods

A simple method for labelling of 16-Br-hexadecanoic acid (16-BrHDA) with radioactive iodine has been reported via nucleophilic¹³¹I-for-Br exchange in the dry state and in organic solvents. While preparation in some organic solvents such as acetic acid, dimethyl formamide (DMF) and dimethyl sulfoxide (DMSO) required reaction times of more than 2 hours to give yields of 20–50%, halogen exchange in dry state at temperature of about 100 °C gave rise to yields of about 94% of radiochemically pure 16-¹³¹IHDA within 5 min. The labelling product could be purified by high performance liquid chromatography (HPLC) and was shown to be free of significant radiochemical impurities.     

Mechanism of charge-transfer polymerization. V. Photopolymerization and photocyclodimerization of N-vinylcarbazole in the N-vinylcarbazole–oxygen–solvent system

Photochemical reactions of N-vinylcarbazole (VCZ), studied in various solvents, were profoundly influenced by the atmosphere. In the deaerated system radical polymerization of VCZ occurred in various solvents, e.g., tetrahydrofuran, acetone, ethyl methyl ketone, acetonitrile, methanol, sulfolane, N,N-dimethylformamide (DMF), or dimethyl sulfoxide (DMSO). By contrast, when dissolved oxygen was present, cyclodimerization of VCZ occurred exclusively to give trans-1,2-dicarbazole-9-yl-cyclobutane in such polar, basic solvents as acetone, ethyl methyl ketone, acetonitrile or methanol. In stronger basic solvents, i.e., sulfolane, DMF, or DMSO, simultaneous radical polymerization and cyclodimerization of VCZ proceeded, the ratio of the cyclodimerization to the radical polymerization decreasing in the order, sulfolane > DMF > DMSO. In dichloromethane, on the other hand, cationic polymerization of VCZ occurred irrespective of the atmosphere. It is suggested that oxygen acts as an electron acceptor to the excited VCZ, electron transfer occurring in polar solvents from the excited VCZ to oxygen to give transient VCZ cation radical. The effect of solvent basicity on the photocyclodimerization of VCZ is discussed.     

Ligand‐free Cu(0)‐mediated controlled radical polymerization of methyl methacrylate at ambient temperature

For the first time, ligand‐free Cu(0)‐mediated polymerization of methyl methacrylate (MMA) was realized by the selection of ethyl‐2‐bromo‐2‐phenylacetate as initiator at ambient temperature. The polymerization can reach up to 90% conversion within 5 h with dimethyl sulfoxide (DMSO) as solvent, while keeping manners of the controlled radical polymerization. Extensive investigation of this system revealed that for a well‐controlled Cu(0)‐mediated polymerization of MMA, the initiator should be selected with the structure as alkyl 2‐bromo‐2‐phenylacetate, and the solvent should be DMSO or N,N‐dimethylformamide. The selectivity for solvents indicated a typical single‐electron transfer‐living radical polymerization process. Scanning for other monomers indicated that under equal conditions, the polymerizations of other alkyl (meth)acrylates were uncontrollable. Based on these results, plausible reasons were discussed. The ligand‐free Cu(0)‐mediated polymerization showed its superiority with economical components and needless removal of Cu species from the resultant products. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

A mechanistic study of arabinigalactan sulfation with potassium persulfate in dimethyl sulfoxide

The mechanism of polysaccharide arabinogalactan sulfation was studied. Potassium persulfate in dimethyl sulfoxide was used as a sulfating agent. Sulfation of the biopolymer proceeds via its reaction with the SO₃—DMSO complex, which is formed upon the reduction of the persulfate anion in DMSO.     

A Novel Non-phosgene Process for the Synthesis of Methyl N-Phenyl Carbamate from Methanol and Phenylurea： Effect of Solvent and Catalyst

A novel environmentally benign process for the synthesis of methyl N-phenyl carbamate (MPC) from methanol and phenylurea was studied. Effect of solvent and catalyst on the reaction behavior was investigated. The IR spectra of methanol and phenylurea dissolved in different solvents were also recorded. Compared with use of methanol as both a reactant and a solvent, phenylurea conversion and selectivity to MPC increased by using toluene, benzene or anisole as a solvent, while phenylurea conversion decreased slightly by using n-octane as a solvent. The phenylurea conversion declined nearly 50% when dimethyl sulfoxide (DMSO) was used as a reaction media, and MPC selectivity decreased as well. The catalytic reaction tests showed that a basic catalyst enhanced the selectivity to MPC while an acidic catalyst promoted the formation of methyl carbamate and aniline. Moderate degree of basicity showed the best catalytic performance in the cases studied.     

Synthesis of Vitamin E Succinate from Candida rugosa Lipase in Organic Medium

A screening of commercially available lipases for the synthesis of vitamin E succinate showed that lipase from Candida rugosa presented the highest yield. The synthesis of vitamin E succinate in organic solvents with different lgP values ranging from -1.3 to 3.5 was investigated. Of particular interest was that dimethyl sulfoxide (DMSO) with the lowest lgP exhibited the highest yield among all the organic solvents used. It suggests that lgP is incapable of satisfactorily predicting the biocompatibility of organic solvents due to the complexity of enzymatic reaction with hydrophilic and hydrophobic substrates in organic solvent. Effects of different operating conditions, such as molar ratio of substrate, enzyme concentration, reaction temperature, mass transfer, and reaction time were also studied. Under the optimum conditions of 10 g/L enzyme, a stirring rate of 100 r/min, a substrate molar ratio of 5:1 at 55℃ for 18 h, a satisfactory yield(46.95%) was obtained. The developed method has a potential to be used for efficient enzymatic production of vitamin E succinate.     

Solvent effects on radical copolymerization of acrylonitrile and methyl acrylate: solvent polarity and solvent-monomer interaction

Abstract

New insights for the effects of organic solvent polarities and solvent-monomer interactions on the radical copolymerization for an important copolymer, poly(acrylonitrile-co-methyl acrylate) (PAN-co-MA), were provided in this research. Solvents, dimethylformamide (DMF), dimethylacetamide (DMAc) and dimethyl sulfoxide (DMSO), were used as reaction media. The polarity of these solvents was in the sequence of DMAc?<?DMF?<?DMSO. By studying the reactivity ratios of AN and MA, the triad fractions of the resultant copolymers, the interactions between monomers and solvents, and the compositions of copolymers at various conversions, we concluded that the solvent polarity had minimal influence on the copolymerization of AN and MA, while the solvent-monomer interactions played important roles. The interactions between monomer-monomer, monomer-solvent, and solvent-solvent, were calculated based on quantum chemistry methods. Both theoretical calculations and experimental results suggested that AN and MA in DMSO tended to aggregate locally, while they could be homogeneously dissolved in DMAc and DMF. The interactions between solvent and monomers could cause local monomer concentration variations, or ‘bootstrap’ effect, which is one of the critical factors affecting the copolymerization process of AN and MA and the chemical structures of the resultant polymers.     

Pyrroles from ketoximes and acetylene 8. Synthesis of 4,5,6,7-tetrahydroindole and its 1-vinyl derivative

4,5,6,7-Tetrahydroindole or 1-vinyl-4,5,6,7-tetrahydroindole was obtained in 81 and 93% yields, respectively, by reaction of cyclohexanone oxime with acetylene at 90–140C in the presence of alkali metal hydroxides or alkoxides in dimethyl sulfoxide (DMSO) or mixtures of DMSO with low-polarity or nonpolar solvents. The reaction is effective both in an autoclave (initial pressure 8–16 gage atm) and at atmospheric pressure.See [1] for communication 7.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 2, pp. 197–199, February, 1979.     

Synthesis and characterization of ruthenium(ii) complexes of 5-hydroxyflavones

Bis(dimethyl sulfoxide)bis(flavonato)ruthenium(II) complexes, RuL₂(DMSO)₂, were synthesized by the reaction of dichlorotetrakis(dimethyl sulfoxide)ruthenium(II) with the sodium salts of 5-hydroxyflavone, 5-hydroxy-4′-methoxyflavone and 5-hydroxy-3′,4′,5′,7-tetramethoxyflavone, ( L ). The complexation was followed by ¹H nmr spectroscopy. The 1:1 kinetically favoured tris(dimethyl sulfoxide)chloroflavonatoruthenium(II) complexes, RuLCl(DMSO)₃, were initially formed and then transformed into the thermodynamically more stable ones. Each one of these complexes, by reacting with another equivalent of lig-and L, also gave rise to a mixture of 1:2 kinetic species, from which the 1:2 thermodynamically more stable bis(dimethyl sulfoxide)bis(flavonato)ruthenium(II) complexes, RuL₂(DMSO)₂, were formed. The complexes were characterized by extensive studies involving ¹H, ¹³C nuclear magnetic resonance, infrared and ultraviolet-visible spectroscopy, mass spectrometry, cyclic voltammetry and elemental analysis. Such 1:2 complexes exhibited properties of two nonequivalent flavonate ligands and also of two non-equivalent dimethyl sulfoxide ligands; one of these dimethyl sulfoxide ligands is considered to be S-bonded and the other O-bonded. Also two quasireversible one-electron redox steps were observed at 0.53 to 0.57 and 0.44 to 0.41 V (vs Saturated Calomel Electrode). The spectroscopic results obtained allow for the discussion of stereochemistry of each bis(dimethyl sulfoxide)bis(flavonato)ruthenium(II) complex and to postulate its possible structure as one corresponding to the more anisochronous species.     

Theoretical study on redox potentials of organic radicals in different solvents

The BMK density functional theory method has been used to examine the redox potentials of organic radicals in different solvents (DMF, N,N-dimethylformamide; DMSO, dimethyl sulfoxide; MeCN, acetonitrile). The polarizable continuum solvation model (PCM) was used to describe the solvation-free energies. The one-electron electrochemical standard potentials (E ⁰) of ca. 100 organic radicals in three solvents were calculated using a single, unified theoretical method whose reliability has been tested against almost all the available experimental data. It was found that the mean absolute deviation (MAD) between the theory and experiment was about 0.08 V. With the newly developed theoretical method in hand, more redox potentials of organic radicals in these three solvents were predicted by this single, unified method. The results showed that the redox potentials of organic radicals in different organic solvents including DMF and DMSO had good correlations with their redox potentials in MeCN.     

Effect of Dimethyl Sulfoxide on the Lamellar Phase of a Zwitterionic Surfactant

We study the effect of dimethyl sulfoxide, a solvent used in biological applications, on the lamellar phases of a zwitterionic surfactant. We used solutions with different proportions of dimethyl sulfoxide/water as solvents in order to analyze the effect on the lamellar phases (regular stacks of surfactant bilayers). The samples were analyzed by macroscopic visual observation, polarized light microscopy, linear rheology, and electron microscopy experiments. The results show that the variation of the dimethyl sulfoxide proportion in the solvent increases the curvature of the bilayers which leads to a transformation from a lamellar phase to an isotropic phase.     

Understanding solvent effects in the selective conversion of fructose to 5-hydroxymethyl-furfural: a molecular dynamics investigation

Selective conversion of fructose to 5-hydroxymethyl-furfural (HMF) involves the participation of high-boiling solvents like dimethyl sulfoxide (DMSO). In order to replace DMSO with low-boiling solvents, it is imperative that we understand the effect of DMSO solvation in protecting (i) HMF from rehydration and humins formation reactions and (ii) fructose from side reactions, other than its dehydration to HMF. In the present work, molecular dynamics simulations of HMF and fructose in water and in water-DMSO mixtures are carried out using the OPLS-AA force field. Radial pair distribution functions, coordination numbers and the hydrogen-bond network between the HMF/fructose molecule and the solvent molecules are analysed. The local 3-dimensional picture of the arrangement of solvent molecules around the solute, which cannot be accessed from pair distribution functions, is also computed. We show preferential coordination of DMSO around HMF and explain how this could provide a shielding effect to the HMF molecule, thus protecting it from further rehydration to levulinic acid and formic acid and from humins formation. In the case of fructose, the presence of DMSO also reduces the number of water molecules in the immediate vicinity of fructose. Though fewer water molecules coordinate around fructose, they are bound strongly to it. Analysis of the local 3-dimensional arrangement of DMSO molecules suggests that it protects the fructose molecule from side reactions that would lead to condensation or reversion products. However, the presence of DMSO molecules does not hamper the water molecules coming into contact with the oxygen atom of the hydroxyl groups of fructose, which is required for a proton transfer from water to fructose, to initiate the dehydration reaction to HMF.     

微波辐射法合成2-(4-取代苯乙烯基)苯并噻唑

甲基苯并噻唑;芳香醛;微波辐射法合成2-(4-取代苯乙烯基)苯并噻唑