Analysis of precision of activation-analysis methods

The precision of an activation-analysis method prescribes the estimation of the precision of a single analytical result. The adequacy of these estimates to account for the observed variation between duplicate results from the analysis of different samples and materials, is tested by the statistic T, which is shown to be approximated by a chi(2) distribution. Application of this test to the results of determinations of manganese in human serum by a method of established precision, led to the detection of airborne pollution of the serum during the sampling process. The subsequent improvement in sampling conditions was shown to give not only increased precision, but also improved accuracy of the results.     

Standard operation protocol for analysis of lipid hydroperoxides in human serum using a fully automated method based on solid-phase extraction and liquid chromatography-mass spectrometry in selected reaction monitoring

Standard operating procedures (SOPs) are of paramount importance in the analytical field to ensure the reproducibility of the results obtained among laboratories. SOPs gain special interest when the aim is the analysis of potentially unstable compounds. An SOP for analysis of lipid hydroperoxides (HpETEs) is here reported after optimization of the critical steps to be considered in their analysis in human serum from sampling to final analysis. The method is based on automated hyphenation between solid-phase extraction (SPE) and liquid chromatography-mass spectrometry (LC-MS). The developed research involves: (i) optimization of the SPE and LC-MS steps with a proper synchronization; (ii) validation of the method-viz. accuracy study (estimated as 86.4% as minimum value), evaluation of sensitivity and precision, which ranged from 2.5 to 7.0 ng/mL (0.25-0.70 ng on column) as quantification limit and precision below 13.2%), and robustness study (reusability of the cartridge for 5 times without affecting the accuracy and precision of the method); (iii) stability study, involving freeze-thaw stability, short-term and long-term stability and stock solution stability tests. The results thus obtained allow minimizing both random and systematic variation of the metabolic profiles of the target compounds by correct application of the established protocol.     

Comparison of denuder and impinger sampling for determination of gaseous toluene diisocyanate (TDI)

An air-sampling method employing denuders coated inside with a chemisorptive stationary phase has been evaluated for analysis of the hazardous gaseous 2,4 and 2,6 isomers of toluene diisocyanate (TDI). The denuder stationary phase consisted of polydimethylsiloxane (SE-30) to which dibutylamine (DBA) was added as a reagent for derivatization of TDI. The accuracy and precision of sampling by means of denuders were shown to differ only slightly from those of the established impinger method. The denuder method was, however, also shown to be suitable for long-term measurements (up to 8 h). The limit of determination (LOD) of the method, including LC-APCI-MS-MS analysis, was found to be 1.9 microg m(-3) and 1.2 microg m(-3) for 2,4- and 2,6-TDI, respectively, for short-term measurements (15 min). Significant lower LOD was obtained for long-term measurements. This is well below the Occupational Safety and Health Administration (OSHA) 8-h TWA (time-weighted average) exposure limit, which is 40 microg m(-3) for the sum of the TDI isomers. The denuder method was also found to be robust and easy to handle. The samplers can be prepared several days before sampling with no loss in performance. The contents of denuders should, on the other hand, be extracted immediately after sampling to prevent degradation of the isocyanate derivatives formed.     

微流动注射进样-加热雾室-等离子体质谱测定血清中的铂

开发了一种基于雾化室加热的微流动注射进样系统,并用于血清中Pt的测定。该进样系统由微量毛细管雾化器、加热微型雾化室、八通道十六孔多功能旋转阀、蠕动泵和注射泵组成。研究了雾化室尺寸、加热温度和采样环体积对信号强度的影响。当雾化室内径为9 mm、加热段长度为6 cm,雾化室温度90 ℃,采样环体积为5 μL时,195Pt的信号强度提高了2.31倍,同时信号精密度从5.1%降至2.2%,并得到峰形良好的信号峰。该进样系统的试样消耗小、灵敏度和检出限均优于常规进样系统。10次测定10 μg/L的Pt标准溶液和血清样品溶液,峰高的RSD分别为2.9%和3.3%。该进样系统测得10个血清中的Pt含量与常规进样系统的测试结果无显著差异,在样品量稀少的情况下具有良好的应用价值。     

Uncertainty in analyte mass for samples containing small numbers of particles.

A sampling equation was derived that relates the standard deviation in analyte mass to the number of particles in the sample, the fractions of the different types of particles in the mixture and the masses and analyte concentrations of the individual particles. The equation, which is applicable to samples containing any number of particles, was verified by sampling and analysis of two cereal grain mixtures for manganese, potassium, chlorine and magnesium, and by Monte Carlo computer simulation. Comparison of the sampling precision of analyte mass with the analytical measurement precision was also studied, and it was shown that use of the equation allows the calculation of the minimum number of particles required to hold the sampling relative standard deviation to that of the analytical measurement.     

A modular fluorimetric stopped-flow system for use in clinical chemistry

Summary A simple, versatile modular stopped-flow system described elsewhere was applied to clinical analyses. The instrument was tested for detection limits, selectivity, precision, dynamic range and sampling rate with conventional rate and equilibrium methods. For this purpose, the determination of copper based on its accelerating effect on a new indicator reaction involving the imidazole/hydrogen peroxide system, was chosen and satisfactorily applied to the analysis of copper in serum. The results obtained show that the stopped-flow method is more advantageous and adequate for routine analysis than two other methods (conventional kinetic and equilibrium techniques).

---

Modulares fluorimetrisches Stopped-Flow-System für die klinische Chemie

     

基于超高效液相色谱-四极杆飞行时间高分辨质谱的高通量血清代谢组学方法

采用超高效液相色谱-四极杆飞行时间高分辨质谱(UPLC-QTOFMS)联用技术, 对血清前处理进行了考察和优化, 并对液-质联用分析条件进行了优化, 旨在建立用于血清中广谱小分子代谢物分析的高通量强耐用代谢组学方法, 以期满足大批次生物样本数代谢组学研究的要求(样本数≥400个). 通过考察不同有机溶剂沉淀蛋白对血清中蛋白的去除程度及38个代表性标准品化合物的提取效果, 确定采用甲醇/乙腈(体积比1: 9)沉淀蛋白法. 血清和有机溶剂的体积比不小于1: 4时, 达到最佳的沉淀蛋白处理效果, 符合大批量样本测试的要求; 预先冷藏沉淀蛋白的有机溶剂, 涡旋2 min, 超声1 min, 加入有机溶剂后冷冻静置10 min, 可以进一步提高前处理沉淀蛋白和化合物提取的效果. 通过对不同流动相体系和梯度条件的考察, 对液-质联用分析条件进行了优化. 方法学考察结果表明, 本方法重现性、 精密度及稳定性均良好. 对重现性和48 h稳定性数据进行变异系数分析和主成分分析法的多维分析, 证明本方法在代谢组学研究中的可重复性及所得数据的可靠性. 本方法高通量强耐用, 每天可测定100多个血清样本(13 min测定1个样本), 适用于代谢组学研究, 特别是大批次生物样本的代谢组学研究.     

Uncertainty of sampling in chemical analysis

 Uncertainty of sampling is the contribution from sampling errors to the combined uncertainty associated with an analytical measurement when the measurand is the concentration of the analyte in the 'target', the total bulk of material that the sample is meant to represent. Of the errors considered to contribute to uncertainty, random errors of sampling, characterised by precision, are much more accessible to investigation than those due to bias. Where an approximation to random sampling can be achieved, realistic precisions can normally be estimated. In some instances reproducibility precision is significantly greater than repeatability precision, and the contribution of between-sampler variations to sampling uncertainty must be acknowledged. However, the collaborative trial of a sampling method is an expensive and difficult exercise to execute. A system of internal quality control for routine sampling can be introduced. Fitness for purpose has been defined in terms of the required combined uncertainty of sampling and analysis. Received: 4 November 1997 · Accepted: 26 November 1997     

Quality control of sampling: proof of concept

Quality control in sampling has been demonstrated as practicable in sampling procedures that require the combination of sample increments to form a composite sample. The proposed method requires no sampling resources or use of time beyond those normally used. Increments are allocated at random into two half-sized composites, each of which is analysed separately. The absolute difference between the two results is plotted on a one-sided control chart, which is interpreted like a Shewhart chart. In commonly prevailing circumstances the analytical precision is negligible and the chart represents sampling precision alone.     

Flow injection analysis for calcium in serum,water and waste waters by spectrophotometry and by ion-selective electrode

The Flow Injection technique is shown to provide fast, reliable and sensitive methods for the determination of calcium in various aqueous as well as serum samples; spectrophotometric or potentiometric detection can be used. At sampling rates of 100–110 samples per hour, with 30-μl sample injections, high reproducibility of measurement and low reagent consumption are achieved in both methods. In the spectrophotometric method, the analytical readout is available within 12 s after sample injection at a total reagent consumption of 0.75 ml per analysis. The potentiometric measurement of the calcium activity in serum is placed on a reliable basis by alternating measurements of serum samples and aqueous standards without incurring any non-reproducible changes in potential between aqueous and serum solutions. This permits the simultaneous determination of pH and pCa, the analytical readout being available within XXX s of sample injection. The good agreement between the results obtained with the Flow Injection method and those attained by atomic absorption and EDTA titrations as well as pCa stat-measurements show that the new methods are potentially suitable for routine analysis.     

新的脉冲进样AAS法测定“麻杏石甘汤”中的微量金属元素

本文研制了一种新的脉冲进样装置，用于火娄原子吸收分光光度法测定中药煎剂中的Ｃａ，Ｍｇ，Ｆｅ，Ｍｎ，Ｚｎ五种金属元素含量，实验表明，利用此种装置可以同时获得两种进样方式的分析结果，线性范围比常规法宽两倍，耗样量，精密度及分析速度均优于常规法。     

Computerized image processing for evaluation of sampling error in ion microprobe analysis

A method is described for the microscale evaluation of sample heterogeneity as applied to in-situ ion microprobe analysis. Computer feature analysis of digitized ion images is utilized to generate sampling constants, which can be related to the degree of heterogeneity present for a particular constituent in the sample. The expected precision for a series of analyses, or the number of analyses required for a desired precision can also be determined. This approach, which is experimentally verified for NBS SRM-664 low-alloy steel, can be used both to minimize sampling error and to assess the applicability of specific reference materials to microprobe analysis.     

Bipolar pulse conductometric detection of enzyme reactions in flow-injection systems Urea in serum and urine

Conductometric monitoring of enzymatic reactions in a flow-injection system is described. Two conductance cells are used and the responses are manipulated automatically to provide a differential signal. The hydrolysis of urea, catalyzed by urease, is used as an example to illustrate the technique. Blood serum and urine control standards are used to assess the precision and accuracy. The conductometric method is shown to be equal to, or better than existing methods for urea with regard to detection limits (0.1 mM in urine, 0.01 mM in serum), working range, precision (3% RSD), accuracy, and sample preparation. The method has a sample throughput of 20 h^?1.     

The analysis of serum urate utilizing immobilized uricase

The evaluation of a method for the estimation of serum urate using immobilized uricase is described, the resultant hydrogen peroxide produced being measured by the oxidative coupling of 3,5-dichloro-2-hydroxybenzenesulfonate and 4-aminophenazone in the presence of peroxidase. A continuous-flow analysis system incorporating the uricase tube was established, and the results obtained were correlated with an automated phosphotungstate method and with a manual uricase method employing an LKB 8600 Rate Reaction Analyser. The effect of ascorbic acid on the analysis of serum urate and the elimination of this interference by the use of ascorbate oxidase was also investigated. The precision, correlation, and high specificity obtained show that this is a satisfactory method for use in routine clinical laboratory works.     

Automated continuous-flow determinations of serum proteins by pulse polarography

A new flow-through cell is described for application of the dropping mercury electrode to the determination of serum proteins in an automated continuous-flow system. By using differential pulse polarography with short controlled drop times, it is possible to run a rapid automated system at sampling rates of up to 120 per hour with approximately +/- 1% precision and less than 3% carry-over. With the Brdicka reagent, hexa-amminecobalt(III) chloride, various serum proteins can be determined in the range 5-50 mug/ml. The method therefore offers a rapid and sensitive automated procedure for determination of serum proteins.     

流动注射-分光光度法测定水中氰化物

使用流动注射(FIA)-分光光度法测定水中的氰化物的含量,并与传统分光光度法的分析结果进行比对。实验证明流动注射(FIA)-分光光度法操作简便、线性好,灵敏度、精密度、准确度都能符合分析工作要求。检出限为0.2μg/L,适用于水中微量氰化物的检测。分析频率为每小时30个样品,特别适合大批样品的测定。     

高浓度试液流动注射在线稀释方法的研究

将分散－区域采样法用于高浓度试液的流动注射在线稀释，并考察了分散管的长度、管径、两次进样的时间间隔等因素对分散度的影响。方法的精密度优于区域采样法，相对标准偏差小于３％。