Mixed electronic and ionic conductivity of LaCo(M)O3 (M=Ga, Cr, Fe or Ni).: V. Oxygen permeability of Mg-doped La(Ga, Co)O3−δ perovskites

The LaGa_1−x−yCo_xMg_yO_3−δ solid solutions with rhombohedrally-distorted perovskite structure were ascertained to form in the concentration range of 0≤y≤0.10 at x=0.60 and 0≤y≤0.20 at x=0.35–0.40. Increasing cobalt content results in increasing electrical conductivity and thermal expansion of the perovskites. Thermal expansion coefficients of the LaGa_1−x−yCo_xMg_yO_3−δ ceramics were calculated from the dilatometric data to vary in the range of 12.4–19.8×10⁻⁶ K⁻¹ at 300–1100 K. Doping La(Ga,Co)O_3−δ solid solutions with magnesium leads to increasing oxygen nonstoichiometry, electronic and oxygen ionic conductivity. Oxygen permeation fluxes through LaGa_1−x−yCo_xMg_yO_3−δ membranes were found to be limited by the bulk ionic conduction and to increase with magnesium concentration, being essentially independent of cobalt content.     

Material design of new lithium ionic conductor, thio-LISICON, in the Li2S–P2S5 system

A new lithium ionic conductor of the thio-LISICON (LIthium SuperIonic CONductor) family was found in the binary Li₂S–P₂S₅ system; the new solid solution with the composition range 0.0≤x≤0.27 in Li_3+5xP_1−xS₄ was synthesized at 700 °C and characterized by X-ray diffraction measurements. Its electrical and electrochemical properties were studied by ac impedance and cyclic voltammetry measurements, respectively. The solid solution member at x=0.065 in Li_3+5xP_1−xS₄ showed the highest conductivity value of 1.5×10⁻⁴ S cm⁻¹ at 27 °C with negligible electronic conductivity and the activation energy of 22 kJ mol⁻¹ which is characteristic of high ionic conduction state. The extra lithium ions in Li₃PS₄ created by partial substitution of P⁵⁺ for Li⁺ led to the large increase in ionic conductivity. In the solid solution range examined, the minimum conductivity was obtained for the compositions, Li₃PS₄ (x=0.0 in Li_3+5xP_1−xS₄) and Li₄P_0.8S₄ (x=0.2 in Li_3+5xP_1−xS₄); this conductivity behavior is similar to other thio-LISICON family with the general formula, Li_xM_1−yM_y′S₄ (M=Si, Ge, and M′=P, Al, Zn, Ga, Sb). Conduction mechanism and the material design concepts are discussed based on the conduction behavior and the structure considerations.     

Perovskite-like system (Sr,La)(Fe,Ga)O3−δ: structure and ionic transport under oxidizing conditions

The maximum solid solubility of gallium in the perovskite-type La_1−xSr_xFe_1−yGa_yO_3−δ (x=0.40–0.80; y=0–0.60) was found to vary in the approximate range y=0.25–0.45, decreasing when x increases. Crystal lattice of the perovskite phases, formed in atmospheric air, was studied by X-ray diffraction (XRD) and neutron diffraction and identified as cubic. Doping with Ga results in increasing unit cell volume, while the thermal expansion and total conductivity of (La,Sr)(Fe,Ga)O_3−δ in air decrease with gallium additions. The average thermal expansion coefficients (TECs) are in the range (11.7–16.0)×10⁻⁶ K⁻¹ at 300–800 K and (19.3–26.7)×10⁻⁶ K⁻¹ at 800–1100 K. At oxygen partial pressures close to atmospheric air, the oxygen permeation fluxes through La_1−xSr_xFe_1−yGa_yO_3−δ (x=0.7–0.8; y=0.2–0.4) membranes are determined by the bulk ambipolar conductivity; the limiting effect of the oxygen surface exchange was found negligible. Decreasing strontium and gallium concentrations leads to a greater role of the exchange processes. As for many other perovskite systems, the oxygen ionic conductivity of La_1−xSr_xFe_1−yGa_yO_3−δ increases with strontium content up to x=0.70 and decreases on further doping, probably due to association of oxygen vacancies. Incorporation of moderate amounts of gallium into the B sublattice results in increasing structural disorder, higher ionic conductivity at temperatures below 1170 K, and lower activation energy for the ionic transport.     

The anomalous behaviour of Gd atoms (Fe1−xMnx)2 compounds

The educed Gd atoms in the X-structure (Th₆Mn₂₃-type) of Gd(Fe_1−xMn_x)₂ were magnetically investigated by comparing with Gd₆(Fe_1−yMn_y)₂₃ whose structure is Th₆Mn₂₃-type. The magnetic properties of Gd(Fe_1−xMn_x)₂ (0.4≤x≤0.7) were observed to be quite similar to those of Gd₆(Fe_1−yMn_y)₂₃ (0.4≤y≤0.7).     

Effect of Pr and Ca substitution on superconductivity in Y(1−x−yPrxCay)Ba2Cu3O7−δ

Pr substituted at constant Ca concentration for Y in (Y_1−x−yPr_xCa_y)Ba₂Cu₃O_7−δ superconductors have been prepared under identical conditions and the temperature dependence of the electrical resistivity of these samples are measured. The resistively determined values of T_c decrease linearly with increasing x (0 ≤ x ≤ 0.2) for constant y = 0.10 and 0.15 which provides convincing evidence that the suppression of superconductivity by Pr is mainly due to magnetic pair breaking. The suppression of superconductivity can also be correlated to the observed changes in oxygen content determined by iodometric analysis and to the average Cu-valences. However, it is found that the observed suppression of T_c cannot be compensated by appropriate hole doping with Ca.     

Lithium insertion to ReO3-type metastable phase in the Nb2O5–WO3 system

Lithium insertion to distorted ReO₃-type metastable solid solution Nb_xW_1−xO_3−x/2 (0≤x<0.25) has been studied by chemical and electrochemical methods. In the course of lithium insertion into tetragonal compounds, transition to a cubic phase was found to occur in the region where values of y (in Li_yNb_xW_1−xO_3−x/2) fall between 0.2 and 0.3, and the phase transition was found to depend on the conditions of the reaction. Changes in OCV and lattice parameters in tetragonal region (y<0.2) were discussed from the viewpoint of the ordering of lithium ions. Also, the component diffusion coefficient of lithium in tetragonal compounds Li_0.1Nb_xW_1−xO_3−x/2 (0≤x≤0.23) was found to increase with niobium content when x≤0.10, and to saturate at 4×10⁻⁹ cm²/s.     

Structure, oxygen stoichiometry and electrical conductivity in the system Sr-Ce-Co-O

Mixed oxides in the system S-Ce-Co-O were prepared by solid state reaction and by freeze-drying of precursor compounds followed by thermal treatment. Two types of perovskite oxides exist in the system: Solid solutions of the type Sr_{1 − y}Ce_yCoO_{3 − x} and mixed oxides of the type (1 − y)SrCeO₃ − ySrCoO_{3 − x}. Microstructures and phase compositions were determined by electron microscopy and X-ray diffraction. SrCoO_{3 − x} forms a solid solution of ceria on the A-site in the strontium cobaltite lattice up to 0.15 mol Ce. This solid solution corresponds to the high-temperature structure of pure SrCoO_{3 − x} and is characterized by high oxygen exchange and electrical conductivity. The oxygen deficiency x was measured by solid electrolyte coulometry. The oxygen deficiency of solid solutions Sr_{1 − y}Ce_yCoO_{3 − x} increases with temperature and decreases with pO₂ in the ambient atmosphere and with increasing Ce dopant concentration. The pO₂-T-x diagram of the solid solution was determined. The T, pO₂ and dopant concentration dependencies of electrical conductivity were measured by a four-point d.c. technique. By Ce doping strontium cobaltite becomes a stabilized high-conductive material (maximum conductivity: 500 S cm⁻¹ at 400 °C, E_a = 0.025 eV, p-type). Above this temperature the T-coefficient of the conductivity changes from positive (semiconducting) to negative values.     

Oxygen overdoping in superconducting and non-superconducting Y1−xPrxBa2Cu3Oy

We present the evolution of magnetic and structural properties of Y_1−xPr_xBa₂Cu₃O_y (x0.5 and x=1) single crystals and polycrystalline materials when the oxygen concentration y is varied from under- to overdoping. We have found a monotonous evolution of the Pr Néel temperature for x=1 samples and a maximum of the superconducting critical temperature for the x0.5 samples. The structural properties as detected by X-ray diffraction and Raman spectroscopy show no instabilities when crossing the optimal doping region as was found in the x=0 material.     

Nax/2Bi1−x/2MoxV1−xO4 and Bi1−x/3MoxV1−xO4 New Scheelite-related phases

New Scheelite-related solid solutions of the compositions Na_x/2Bi_1−x/2Mo_xV_1−xO₄ (0≤x≤1) and Bi_1−x/3 Mo_xV_1−xO₄(0≤x≤0.2) have been synthesised by the substitution of Na and Mo at the A and B sites respectively of the ABO₄ type ferroelastic BiVO₄. The phases were characterised using chemical analysis, powder X-ray diffraction, scanning electron microscopy, EDAX, and Raman spectroscopy. While almost a continuous solid solution is obtained for the series Na_x/2Bi_1−x/2Mo_xV_1−xO₄, the absence of Na at the A-site results only in a narrow stability region for the other series, Bi_1−x/3 Mo_xV_1−xO₄ where 0≤x≤0.2. Raman spectra of selected samples at room temperature also suggest that vanadium and molybdenum atoms are disordered at the tetrahedral sites.     

Oxygen nonstoichiometry and phase transitions of the neodymium-rich Nd1+xBa2−xCu3Oz solid solution

On the basis of chemical, thermal analysis and Cu K-edge X-ray absorption measurements, oxygen content in the Nd_1+xBa_2−xCu₃O_z solid solution was determined between 1000°C in air and 400°C in oxygen for x=0.05–0.9 compositions. It has been observed that the oxygen nonstoichiometry Δz of the Nd_1+xBa_2−xCu₃O_7+x/2−Δz solid solution decreases 2–2.5 times for a large substitution (Δz≈0.3–0.33 for x=0.9), despite of the acclaimed higher total oxygen content. The difference in nonstoichiometry is explained by a higher average value of the copper oxidation state (ACV), which is vital for the solid solution with large x even at elevated temperatures (ACV≈2–2.05 for x>0.3 at 1000°C, PO₂=0.21 atm). On the contrary, the ACV after complete oxygenation is almost constant (about 2.25–2.3) for the whole series. The x-dependence of the oxygen content is not monotonous and structural phase transitions can be observed at x=0.3 and x=0.6, as confirmed by the X-ray diffraction and the Raman scattering spectroscopy. The first well-known transition is connected with the oxygen disorder due to the Nd substitution for Ba at random Ba-sites. In the present work, it is proved by the apical oxygen mode broadening in Raman spectra. Ordering of the Nd and Ba atoms with a subsequent orthorhombic distortion of the lattice may occur even at 1000°C in air due to the second transformation at x≈0.6. The invariable orthorhombicity of the Nd-rich solid solution with x>0.6 is not caused by the oxygen absorption as in the x=0.05 case. Existence of high- and low-temperature orthorhombic modifications of this solid solution has been observed for the first time. Finally, a tentative 3D (z–x–T) diagram is suggested for the Nd_1+xBa_2−xCu₃O_z solid solution up to 1000°C in air, including the new x=0.6–0.9 region.     

Phonon Raman scattering in Nd1+xBa2−xCu3O7−δ and Pr1+xBa2−xCu3O7−δ single crystals

The polarized Raman spectra of Nd_1+xBa_2−xCu₃O_7−δ (−0.023≤x≤0.107) and Pr_1+xBa_2−xCu₃O_7−δ (0.01≤x≤0.15) single crystals have been investigated. It was found that the Cu(2) A_g mode softens by 6 cm⁻¹ in Nd 1:2:3 and 4 cm⁻¹ in Pr 1:2:3 as x increases. These frequency shifts cannot be explained by the change in the relevant bond lengths due to Nd(Pr)-substitution for Ba. The variations with x of the two low frequency modes may be affected by change of their hybridization and/or change of their force constants. The linewidths of Ba mode in Pr 1:2:3 are broader than those in Y 1:2:3. This result suggests that the Pr substitution on Ba sites occurred even in a very small value of x. In x(yy) geometry the relative intensity of the Ba and O(4) modes in Nd 1:2:3 is greater than those in Pr 1:2:3. The difference between Nd 1:2:3 and Pr 1:2:3 in the relative intensity of the Ba and O(4) modes may be produced by the chains.     

The effect of oxygen vacancy on the oxide ion mobility in LaAlO3-based oxides

The electrical property of (La_1−xSr_x)_1−z(Al_1−yMg_y)O_3−δ (LSAM; x≤0.3, y≤0.15 and z≤0.1) was measured using the DC four-probe method as a function of temperature (500–1000°C) and oxygen partial pressure (1–10⁻²² atm). Among LSAMs, (La_0.9Sr_0.1)AlO_3−δ showed the highest ionic conductivity, σ_i=1.3×10⁻² S cm⁻¹ at 900°C. A simultaneous substitution at A and B sites or A site deficiency is expected to create larger oxygen vacancy and higher ionic conductivity. However, it showed a negative effect. The effect of the vacancy increase did not effect monotonously the ionic conductivity. It was found that the concentration of oxygen vacancy, [V_O], influences not only the oxide ion conductivity, σ_i, but also the mobility, μ_v, of [V_O]. These properties exhibit a maximum at around [V_O]=0.05. With the increase in [V_O], the activation energy, E_a, of the ionic conduction dropped from 1.8 to ca. 1.0 eV at [V_O]=0.05 and became almost constant at [V_O]>0.05. The dependency of the pre-exponential term, μ⁰_v, and E_a on [V_O] was analyzed and their effect on μ_v and σ_i was discussed with respect to crystal structure and defect association. It was estimated that the crystal structure mainly governs these properties. The effect of defect association could not be ignored but is considered to be a complicated correlation.     

Oxygen permeability of La2Cu(Co)O4+δ solid solutions

Formation of the La₂Cu_1−xCo_xO_4+δ solid solutions with orthorhombic K₂NiF₄-type structure was found to be in the range of 0≤x≤0.30 at temperatures above 1270 K. Incorporating cobalt into the copper sublattice of lanthanum cuprate leads to increasing oxygen hyperstoichiometry and decreasing electrical conductivity. Thermal expansion coefficients of the La₂Cu_1−xCo_xO_4+δ (x=0.02–0.30) ceramics at 470–1100 K were calculated from the dilatometric data to vary in the range (12.2–13.2)×10⁻⁶ K⁻¹. Studying the dependence of oxygen permeation fluxes through La₂Cu(Co)O_4+δ on the membrane thickness demonstrated that the oxygen transport at the thickness values below 1 mm is limited by both surface exchange rate and bulk ionic conductivity. Oxygen permeability of the La₂Cu_1−xCo_xO_4+δ solid solutions was ascertained to increase with cobalt concentration at x=0.02–0.10 and to decrease with further dopant additions, indicating a participation of interstitial oxygen in the ionic transport.     

Effect of cobalt substitution on cationic distribution in LiNi1 − y CoyO2 electrode materials

A crystal chemistry study of LiNi_{1 − y}Co_yO₂ phases, used as positive electrode in lithium batteries, is presented. These materials crystallize in the rhombohedral system (space group: R m) with a layered structure. Rietveld profile refinement of the X-ray data shows that for low substitution amounts ( ≤ 0.20) extra-nickel ions are always present leading to the Li_{1 − z}Ni_{1 + z − t}CotO₂ (t = y(1 + z)) formula (z * > 0), while for y ≥ 0.30, a pure 2D structure is obtained (z = 0). The stabilization of the 2D character of the structure by cobalt substitution in lithium nickelate leads to the improvement of the electrochemical properties.     

Temporary phase segregation processes during the oxidation of (Fe0.7Mn0.3)0.99O in N2---H2O atmosphere

A two-step thermochemical cycle with the ternary metal oxide system (Fe_{1 − x}Mn_x)₃O₄/(Fe_{1 − x}Mn_x)_{1 − y}O is applied to convert solar energy to chemical energy. Experimental investigations on the water splitting reaction of (Fe_{1 − x}Mn_x)_{1 − y}O revealed temporary formation of a manganese rich rock salt phase and an iron rich spinel phase due to phase segregation processes.     

Scaling limit of deeply virtual compton scattering

I outline a perturbative QCD approach to the analysis of the deeply virtual Compton scattering process γ^*p → γp′ in the limit of vanishing momentum transfer t = (p′ − p)². The DVCS amplitude in this limit exhibits a scaling behavior described by two-argument distributions F(x,y) which specify the fractions of the initial momentum p and the momentum transfer r ≡ p′ − p carried by the constituents of the nucleon. The kernel R(x,y;ξ,η) governing the evolution of the non-forward distributions F(x,y) has a remarkable property: it produces the GLAPD evolution kernel P(x/ξ) when integrated over y and reduces to the Brodsky-Lepage evolution kernel V(y,η) after the x-integration. This property is used to construct the solution of the one-loop evolution equation for the flavor non-singlet part of the non-forward quark distribution.     

Ionic conduction in CuxAg1−xBrTe solid solutions

The ionic conduction of cation substituted CuBrTe, Cu_xAg_1−xBrTe solid solutions, is investigated in the temperature range between 100 and 400 K. The change of electrical conductivities with temperature in the range of 0.94≤x<1 shows the characteristics of second-order rather than first-order phase transitions. The replacement of Cu with the Ag cation in Cu_xAg_1−xBrTe leads to an increase in conductivity especially in the β and γ-phases.     

Oxygen nonstoichiometry effect on structural modulation in Bi-2212 cuprate superconductors

The X-ray diffraction patterns for Bi₂Sr₂Ca_1−xY_xCu₂O_8+y sintered in air or Ar indicated that the reduction in the number of excess oxygen ions induced a structural change from orthorhombic to pseudotetragonal. When the oxygen contents decreased with the reducing treatment, the period of modulation in Bi₂Sr₂Ca_1−xY_xCu₂O_8+y increased. This result supported the model of excess oxygen ions in the Bi---O sheet. However, it was difficult to understand the change of modulation period with increasing Y contents using the model of excess oxygen ions in the Bi---O layers. Also, it is included that the Y substitution for Ca and La substitution for Sr in the Bi₂Sr₂CaCu₂O_8+y system result in parallel effects for the modulation structure.     

Annealing effects on the magnetization of Co–Ni–B amorphous nanoparticles

Chemically prepared (Co_xNi_1−x)_1−yB_y (x=0.5, 0.75, 1; y≈0.4) amorphous fine particles were characterized by X-ray diffraction, DTA and TGA, and in situ magnetic measurement as a function of annealing temperature in an inert atmosphere. Magnetic measurement performed in as-prepared and 150°C annealed samples shows an increase of the saturation magnetization and magnetic moment after thermal treatment. Room temperature magnetization increases by factors of 3.5, 1.8, and 1.5, for x=0.5, 0.75, and 1, respectively. These measurements may indicate a local re-ordering of the amorphous phase at temperatures much lower than the full crystallization temperature.     

Preparation, characterization and oxide ion conductivity in U-substituted Bi4V2O11

A Bi₂V_{1 − x − y}U_xBi_yO_{5.5 + 0.5x − y} solid solution derived from Bi₄V₂O₁₁ has been prepared and characterized with x up to 0.125 for y = 0. Partial substitution of U⁶⁺ for V⁵⁺ in Bi₄V₂O₁₁ leads to the stabilization at room temperature of the high-oxide ion conducting γ-phase, in contrast with other M⁶⁺ dopants which stabilize the β-phase. The lower conductivity in U substituted system compared with BICUVOX.10 is attributed to its higher activation energy. Conductivity values and activation energies of the U substituted phases compare well with Bi₂UO₆.