An attempt to extend ordinary capillary gas chromatography to supercritical fluid chromatography (SFC)

Since capillary columns with well immobilized stationary phases are expected to withstand contact with supercritical fluids, we wished to study their amenability to SFC. Simultaneously, we wished to learn how far SFC can be accomplished with the ordianary tools of capillary GC. The study demonstrates that truly supercritical, not just relatively high, pressure is required to ensure the typical effects of SFC. Results obtained with sub-and supercritical pressure are compared and discussed. A comprehenshive study of the parameters permitting SFC with capillary GC equipment showed a clear preference for CO₂ as a carrier, FID detection, and oncolumn sampling. While no additional equipment is required, a critical feature is the flow restrictor to be mounted on the end of the column. The production and properties of this restrictor are discussed in detail. It is reasonable to hope that SFC with 0.1 mm id capillary columns can be realized in the pressure range of 100–150 bar, where substances which cannot be eluted from a capillary colum under GC donditions are expected to be analyzed.     

Capillary supercritical fluid chromatography with flame photometric detection using a large bore column SFC pumping system

A commercially available instrument with an SFC pumping system suitable for wide bore columns (4.6 mm i.d.) has been modified for capillary supercritical fluid chromatography (CSFC) by incorporating a double-stage flow splitter. The first flow splitter was installed in front of the sample injection valve in order to avoid a high solute split ratio. The second splitter was mounted in the column oven so that the injected sample (0.2 μL) would be split to the capillary column. In order to perform pressure programmed elution, a pressure regulating system equipped with a gradient programmer has been used. Flame photometric detection was optimized for the analysis of organosulfur compounds by CSFC. In this study, detection limits were found to be 6–14 ng and the experimentally determined exponent (n value) varied from 1.721 to 1.984 depending on the compounds tested. Sulfur- and phosphorus-containing thermally labile pesticides can be chromatographed and selectively detected by using CSFC/FPD in either sulfur- or phosphorus mode, respectively.     

Characterization of low molecular weight alkoxylated polymers using long column SFC/MS and an image analysis based quantitation approach

The utility of low viscosity mobile phases and long chromatographic columns for complex polymer analysis is demonstrated. We use long column supercritical fluid chromatography/mass spectrometry (SFC/MS) with electrospray ionization (ESI) to characterize a variety of complex, low molecular weight polymers. When quantitative analysis is desired, the resulting three-dimensional (time, intensity, and mass-to-charge ratio [m/z]) data are converted to images. Custom image analysis software is used to detect and integrate peaks in arbitrarily defined regions of the time-m/z map. These integrated peak volumes can be used to quantitate distinct component classes of the polymer mixtures.     

Capillary and packed column SFC/MS

A frit restrictor interface for capillary column supercritical fluid chromatography/mass spectrometry (SFC/MS) has been constructed and used for the analysis of high boiling point alkanes. Packed column SFC/MS is described using both a moving belt liquid chromatographic/mass spectrometric interface and a thermospray source in the filament-on mode.     

Simultaneous coupling of capillary supercritical fluid chromatography and high temperature glass capillary gas chromatography to a mass spectrometer

The coupling of glass capillary supercritical fluid chromatography to a high temperature GC/MS system via a micrometeradjustable glass capillary interface including an integrated pressure restrictor is described. With this coupling device, both complementary capillary chromatographic methods retain their full independence and flexibility. It is shown that in supercritical fluid chromatography glass fulfils all the requirements of a suitable support material. The preparation of narrow bore glass capillary columns (0.06 mm i.d.), coated with chemically bonded and crosslinked fluids with a film thickness of about 0.6 μm, which exploit the merits of OHterminated polysiloxanes as stationary phases is discussed. The application of glass capillary SFC is demonstrated and compared with examples given in the literature.     

Quantitation in miniaturized GC and SFC systems

Separations of high efficiency and/or speed can be achieved in capillary GC by capillary columns of lower internal diameter (< 50 μm). Sampling techniques for the analytical application of narrow bore fused silica columns have been evaluated with regard to quantitation. On-column injection cannot be applied. Therefore liquid samples have to be vaporized in external devices before they enter the chromatographic system. Sample introduction by syringe with subsequent splitting must and can be applied but requires special syringes with perfect piston sealing because of the high inlet pressures needed even with hydrogen as carrier gas. For general analytical applications, valve systems should be developed to eliminate both the syringe and the septum from instrumental GC set-up's. In SFC using either narrow bore capillary or packed microbore columns, time-controlled valve sampling with partial displacement of the sample from the loop seems to be an adequate technique because of the very high inlet pressures involved. Splitting in combination with valve operation can also be applied in capillary SFC at least to samples of good solubility in the mobile phase. A disadvantage of splitting in SFC is that another restriction for the adjustment of the split flow is necessary.     

The application of capillary SFC,packed column SFC,and capillary SFC-MS in the analysis of controlled drugs

Multi–component mixtures of controlled drugs, drug impurities, and adulterants have been analyzed by capillary SFC-FID, packed column SFC-UV, and capillary SFC-MS. Isocratic packed column SFC has been performed with binary and ternary mobile phases using a single syringe pump. The combination of capillary SFC and double focusing MS is described with reference to MS source pressures and the spectra obtained. The use of negative temperature programming in SFC is described.     

Application of capillary supercritical fluid chromatography to the analysis of a middle distillate fuel

Summary The application of capillary supercritical fluid chromatography (SFC) to the analysis of a middle distillate fuel is described. Small diameter (50m i.d.) fused-silica capillary columns coated with crosslinked 50% phenyl polymethylphenyl siloxane provided high separation efficiency and good compatibility with flame ionization detection. High resolution separations of the chemical class fractions obtained by adsorption chromatography on alumina were obtained using carbon dioxide as the supercritical mobile phase and simple pressure programming techniques. In addition to the less polar fuel components, supercritical carbon dioxide allowed chromatography of the nitrogen-containing polycyclic aromatic hydrocarbon fraction and the hydroxylated polycyclic aromatic materials.     

Fast supercritical fluid chromatography of polymers using packed capillary columns

Summary Fast separations of perfluorinated polyethers and polymethylsiloxanes that are composed of 50–80 oligomers were demonstrated in packed capillary column supercritical fluid chromatography (SFC) using a carbon dioxide mobile phase. Separations were accomplished within 10 min using a 13 cm×250 μm i.d. column packed with 2 μm porous octadecyl bonded silica (ODS) particles. Effects of particle diameter of the packing material and pressure programming on separation were investigated, and packed column SFC was compared with open tubular column SFC. Results show that as the particle diameter was decreased from 5 to 3 to 2 μm and the column length was reduced from 85 to 43 to 13 cm, the separation time could be reduced from 70 to 20 to 10 min while still maintaining similar separation (resolution). Short columns packed with small porous particles are very suitable for fast SFC separations of polymers.     

Reviews on recent trends in chromatography/mass spectrometry coupling. Part IV. Reasons why supercritical fluid chromatography is not so easily coupled with mass spectrometry as originally assessed

Summary When SFC was rediscovered in the early 1980s, it was frequently estimated that a strong driving force to its development would be the ease of devising a simple SFC/MS interface. This was believed to be easily achieved if analytical conditions were limited to capillary SFC columns as a general separation tool, and to the choice of neat CO₂ as the unique supercritical fluid. The low flow rate of mobile phase delivered by capillary columns was easy to accommodate by the vacuum equipment of standard mass spectrometers, and the specific physical properties of CO₂ made possible solute ionization by different ion-molecule reactions, especially charge exchange ionization. This approach has lived up to all of its promises. The major causes of the observed mismatch are the large variations of the MS source pressure as a result of the CO₂ pressure gradient at the SFC column inlet, the low sensitivity of charge exchange ionization at these high MS source pressures, and the inability to handle polar and nonvolatile molecules. Adaptation of LC/MS interfaces, such as the thermospray interface or the particle beam interface, to SFC/MS conditions was a step forward, but these devices have their own limitations. Alternative methods to direct SFC/MS coupling have been investigated recently. They are based on the use of packed columns rather than capillaries, and on solute ionization at atmospheric pressure rather than under a vacuum, by means of either gas-phase corona discharge ionization or liquidphase electrospray ionization. These new developments may revive research into the design of reproducible and sensitive SFC/MS systems where the number of recent studies is still low compared with other chromatography/mass spectrometry coupling studies.See [1] for part III     

Highly sensitive and accurate profiling of carotenoids by supercritical fluid chromatography coupled with mass spectrometry

We attempted to establish a high‐speed and high‐resolution profiling method for a carotenoid mixture as a highly selective and highly sensitive detection method; the analysis was carried out by supercritical fluid chromatography (SFC) coupled with mass spectrometry (MS). When an octadecyl‐bonded silica (ODS) particle‐packed column was used for separation, seven carotenoids including structural isomers were successfully separated within 15 min. This result indicated not only improved separation but also improved throughput compared to the separation and throughput in RP‐HPLC. The use of a monolithic ODS column resulted in additional improvement in both the resolution and the throughput; the analysis time was reduced to 4 min by increasing the flow rate. Furthermore, carotenoids in biological samples containing the complex matrices were separated effectively by using several monolithic columns whose back pressure was very low. The mass spectrometer allowed us to perform a more sensitive analysis than UV detection; the detection limit of each carotenoid was 50 pg or below. This is the first report of carotenoid analysis carried out by SFC‐MS. The profiling method developed in this study will be a powerful tool for carrying out accurate profiling of biological samples.     

Simultaneous determination of a spectrum of trichothecene toxins out of residuals of biogas production

A sensitive and selective method for the simultaneous determination of a spectrum of trichothecenes in residuals of biogas production has been developed. It comprises sample clean-up by liquid/liquid partition for digested manure and solid phase extraction for digested solid phase. Quantification of A- and B-type trichothecenes as their trifluoroacetyl derivatives is performed by gas chromatography mass spectrometry (GC/MS), that of B-type trichothecenes alternatively by high-performance liquid chromatography (HPLC). Fluorescence detection (FLD) after post-column derivatisation using methylacetoacetate and ammonium acetate after alkaline decomposition of toxins was applied. Detection limits in digestates were between 1 and 30 microg/l and 20 and 50 microg/l for GC/MS and HPLC/FLD, respectively. Recovery rates were between 52 and 129% for GC/MS detection with the exception of T-2 tetraol with 22%, and between 56 and 123% for HPLC/FLD.     

Use of small diameter WCOT columns for ultra-high resolution GC/MS

For clinical and environmental analyses utilizing capillary gas chromatography/mass spectrometry (GC/MS), increased sensitivity and speed of analysis are highly desirable. These performance advantages are realized using a WCOT column of 100 μm i.d. as compared to the more conventional 200 μm i.d. capillary columns. The improved sensitivity of capillary direct GC/MS with the 100 μm i.d. column for the confirmation of drugs of abuse will be demonstrated. For environmental analysis, the superior efficiency and resolution of the 100 μm i.d. column can be employed for the separation of priority pollutants. This approach is more amenable to capillary direct GC/MS providing a more effective interface to the mass spectrometer. As a result improved sensitivity and a considerable decrease in analysis time is achieved over that obtained with the larger diameter environmental specialty phase columns.     

Advantages and drawbacks of popular supercritical fluid chromatography/mass interfacing approaches--a user's perspective

Mobile phases in supercritical fluid chromatography (SFC) have low viscosities and high diffusion coefficients with respect to those of traditional high performance liquid chromatography (HPLC). These properties allow higher mobile phase flow rates and/or longer columns in SFC, resulting in rapid analyses and high efficiency separations. In addition, chiral SFC is becoming especially popular. Mass spectrometry (MS) is arguably the most popular "informative" detector for chromatographic separations. Most SFC/MS is performed with atmospheric pressure ionization (API) sources. Unlike LC/MS, the interface between the SFC column and the API source must allow control of the downstream (post-column) pressure while also providing good chromatographic fidelity. Here we compare and contrast the popular interfacing approaches. Some are simple, such as direct effluent introduction with no active back-pressure-regulator (BPR) in high speed bioanalytical applications. The pressure-regulating-fluid interface is more versatile and provides excellent chromatographic fidelity, but is less user friendly. The pre-BPR- split interface and an interface which provides total-flow-introduction with a mechanical BPR are good compromises between user friendliness and performance, and have become the most popular among practitioners. Applications of SFC/MS using these various interfaces are also discussed.     

Evaluation of low-pressure gas chromatography linked to ion-trap tandem mass spectrometry for the fast trace analysis of multiclass pesticide residues

A rapid multiresidue method for the analysis of 72 pesticides has been developed using a single injection with low-pressure gas chromatography/tandem mass spectrometry (LP-GC/MS/MS). The LP-GC/MS/MS method used a short capillary column of 10 m x 0.53 mm i.d. x 0.25 microm film thickness coupled with a 0.6 m x 0.10 mm i.d. restriction at the inlet end. Optimal LP-GC conditions were determined which achieved the fastest separation in MS/MS detection mode. Also MS/MS conditions were optimized in order to increase sensitivity and selectivity. The analytical parameters of the LP-GC/MS/MS method were compared with those obtained by GC/MS/MS using a conventional capillary column (30 m x 0.25 mm i.d. x 0.25 microm film thickness). Better precision and sensitivity values were obtained with the LP-GC/MS/MS approach. The limits of detection (LOD) of the compounds ranged from 0.1 to 14.1 microg L(-1) for LP-GC/MS/MS, lower than those obtained for conventional GC/MS/MS that ranged from 0.1 to 17.5 microg L(-1). The peak widths obtained with the short column in LP-GC are similar to those obtained using conventional capillary GC columns, and the peaks can be successfully identified by MS/MS detection with the conventional scan speed of ion-trap instruments. In addition, the analysis time was significantly reduced with LP-GC/MS/MS (32 min) versus GC/MS/MS (72 min), allowing the number of samples analyzed per day in a routine laboratory to be doubled.     

Capillary column SFC instrumentation based on piston pumps with a programmable back-pressure regulator for on-line mixing of mobile phases

An alternative phase delivery system based on piston pumps and a back-pressure regulator has been developed for capillary column SFC. The chromatography is not affected by the fast piston pump refill. A homogeneous on-line mixing of binary phases with simultaneous pressure programming is easily accessible without any additional computing. Acceptable reproducibilities (< 3.5% RSD for external and < 2.0% RSD for internal standard methods) were found with mixtures of 2-propanol/CO₂ as mobile phases using UV detection and split ratios of 1:60 and 1:120. Variation and control of the split are easily done by simple flow rate volumetric changes.     

Enhancement of sensitivity in capillary supercritical fluid chromatography through optimization of injection and detection techniques

The reproducibility of peak areas as a function of the technique used for sample injection was investigated in capillary supercritical fluid chromatography (SFC). An injection technique has been developed to increase the volume of sample introduced into the capillary column. Using a modified time-split injection technique, long injection duration times were successfully applied to achieve lower detection limits. Analytes were effectively focused at the head of the analytical column using a unique pressure trap program. Because this on-column focusing was performed only by pressure and temperature programming, no instrumental modifications were necessary. Up to 1.0 μL of sample solution was injected onto 50 μm i.d. columns using this technique, with no observable peak splitting. Dual detection using ultraviolet (UV) absorption and flame ionization detection (FID) was performed in series, thereby avoiding the necessity of splitting the column effluent. For the compounds investigated (five nitroaromatics and one phthalate ester), the absolute sensitivity of the UV detector was significantly greater than that of the FID.     

Analysis of turkish lignite tar by coupled LC/GC,GC/MS,and capillary SFC

This work describes the analysis of a pyrolysis product of a lignite sample obtained from the Turkish Goynuk reserve. The aliphatic, aromatic and polar compounds present in the tar are separated and identified by various chromatographic techniques: Capillary gas chromatography/mass spectrometry (GC/MS), on-line high performance microbore liquid chromatography/capillary gas chromatography (LC/GC) and capillary supercritical fluid chromatography (SFC). The suitability of each technique for this particular application is discussed, and semi-quantitative results are presented for the major components detected.     

Development of a simultaneous liquid chromatography/tandem mass spectrometric method for the determination of type B trichothecenes, their derivatives, and precursors in wheat

A method coupling liquid chromatography with tandem mass spectrometry (LC/MS/MS) was developed for the simultaneous quantitative determination of trichothecenes, nivalenol, deoxynivalenol, deoxynivalenol‐3‐glucoside, fusarenon‐X, 3‐acetyldeoxynivalenol, 15‐acetyldeoxynivalenol, isotrichodermin, calonectrin, 3‐deacetylcalonectrin, 15‐deacetylcalonectrin, 3,15‐diacetylnivalenol, 4,15‐diacetylnivalenol, 3,15‐diacetyldeoxynivalenol, and 3,4,15‐triacetylnivalenol. The analytical parameters of trichothecenes and their derivatives were optimized to enable their highly sensitive detection. Evaluation of clean‐up procedures using Multisep #226 and #227 indicated that Multisep #227 was more suitable for their simultaneous detection in wheat. In performance validation studies using the LC/MS/MS method with Multisep #227 cleanup, good recoveries ranging from 84% to 115% with relative standard deviations from 0.4% to 7.2% were measured. The limits of detection and quantification ranged from 0.03 to 1.4 ng·g^?1 and from 0.1 to 4.7 ng·g^?1, respectively. The effect of matrices using matrix‐matched calibration was estimated to range from 80% to 117% after Multisep #227 cleanup. Multisep #227 clean‐up procedure with matrix‐free standard calibration achieved accurate quantification without having a considerable effect on matrix compounds. Using the developed method, several trichothecene derivatives and precursors were detected in fungally inoculated wheat samples. The developed LC/MS/MS method is a practical technique that can be used for the quantification of trichothecenes in wheat. This study is the first report of an analytical method used for the simultaneous quantification of major trichothecenes, their derivatives and precursors. Copyright © 2011 John Wiley & Sons, Ltd.     

Supercritical fluid chromatography tandem-column method development in pharmaceutical sciences for a mixture of four stereoisomers

A tandem-column method using Chiralpak AD-H and Chiralcel OD-H columns was achieved for baseline separation of a mixture of chiral pharmaceutical compounds (i.e., four stereoisomers) via supercritical fluid chromatography (SFC) with a mobile phase consisting of 90% liquid carbon dioxide and 10% ethanol:isopropanol (50:50 v/v). On the contrary, this mixture (mixture A) could not be baseline separated by SFC conditions explored with individual Chiralpak AD-H and Chiralcel OD-H columns. The effects of various mobile phases on elution order, capacity factor, selectivity, and resolution were determined with mixture A on the individual aforementioned columns to develop the tandem-column method.