In situ crosslinking of polyoxometalate-polymer nanocomposites for robust high-temperature proton exchange membranes

The most practical high-temperature proton exchange membranes (PEMs) are phosphoric acid (PA)-doped polymer electrolytes. However, due to the plasticizing effect of PA, it is a challenge to address the trade-off between the proton conductivity and the mechanical performance of these materials. Here, we report an effective strategy to fabricate robust high-temperature PEMs based on the in situ electrostatic crosslinking of polyoxometalates and polymers. A comb copolymer poly(ether-ether-ketone)-grafted-poly(2-ethyl-2-oxazoline) (PGE) with transformable side chains was synthesized and complexed with H₃PW₁₂O₄₀ (PW) by electrostatic self-assembly, forming PGE/PW nanocomposite membranes with bicontinuous nanostructures. After a subsequent PA-treatment of these membranes, high-temperature PEMs of PGE/PW/PA ternary nanocomposites were obtained, in which the in situ electrostatic crosslinking effect between PW and PGE side chains was generated in the hydrophilic domains of the bicontinuous structures. The microphase separation structure and the electrostatic crosslinking feature endow the PGE/PW/PA membranes with excellent anhydrous proton conductive ability while retaining high mechanical performance. The membranes show a high proton conductivity of 42.5 mS/cm at 150 °C and a high tensile strength of 13 MPa. Our strategy can pave a new route based on electrostatic control to design nanostructured polymer electrolytes.     

Nanocomposite blend gel polymer electrolyte for proton battery application

A proton-conducting nanocomposite gel polymer electrolyte (GPE) system, [35{(25 poly(methylmethacrylate) (PMMA) + 75 poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP))?+?xSiO₂}?+?65{1 M NH₄SCN in ethylene carbonate (EC) + propylene carbonate (PC)}], where x?=?0, 1, 2, 4, 6, 8, 10, and 12, has been reported. The free standing films of the gel electrolyte are obtained by solution cast technique. Films exhibit an amorphous and porous structure as observed from X-ray diffractometry (XRD) and scanning electron microscopy (SEM) studies. Fourier transform infrared spectrophotometry (FTIR) studies indicate ion–filler–polymer interactions in the nanocomposite blend GPE. The room temperature ionic conductivity of the gel electrolyte has been measured with different silica concentrations. The maximum ionic conductivity at room temperature has been observed as 4.3?×?10^?3?S?cm^?1 with 2 wt.% of SiO₂ dispersion. The temperature dependence of ionic conductivity shows a typical Vogel-Tamman-Fulcher (VTF) behavior. The electrochemical potential window of the nanocomposite GPE film has been observed between ?1.6 V and 1.6 V. The optimized composition of the gel electrolyte has been used to fabricate a proton battery with Zn/ZnSO₄·7H₂O anode and PbO₂/V₂O₅ cathode. The open circuit voltage (OCV) of the battery has been obtained as 1.55 V. The highest energy density of the cell has been obtained as 6.11 Wh?kg^?1 for low current drain. The battery shows rechargeability up to 3 cycles and thereafter, its discharge capacity fades away substantially.     

Effect of plasticizers (EC or PC) on the ionic conductivity and thermal properties of the (PEO)9LiTf: Al2O3 nanocomposite polymer electrolyte system

A new plasticized nanocomposite polymer electrolyte based on poly (ethylene oxide) (PEO)-LiTf dispersed with ceramic filler (Al₂O₃) and plasticized with propylene carbonate (PC), ethylene carbonate (EC), and a mixture of EC and PC (EC+PC) have been studied for their ionic conductivity and thermal properties. The incorporation of plasticizers alone will yield polymer electrolytes with enhanced conductivity but with poor mechanical properties. However, mechanical properties can be improved by incorporating ceramic fillers to the plasticized system. Nanocomposite solid polymer electrolyte films (200–600 μm) were prepared by common solvent-casting method. In present work, we have shown the ionic conductivity can be substantially enhanced by using the combined effect of the plasticizers as well as the inert filler. It was revealed that the incorporating 15 wt.% Al₂O₃ filler in to PEO: LiTf polymer electrolyte significantly enhanced the ionic conductivity [σ _RT (max)?=?7.8?×?10^?6 S cm^?1]. It was interesting to observe that the addition of PC, EC, and mixture of EC and PC to the PEO: LiTf: 15 wt.% Al₂O₃ CPE showed further conductivity enhancement. The conductivity enhancement with EC is higher than PC. However, mixture of plasticizer (EC+PC) showed maximum conductivity enhancement in the temperature range interest, giving the value [σ _RT (max)?=?1.2?×?10^?4 S cm^?1]. It is suggested that the addition of PC, EC, or a mixture of EC and PC leads to a lowering of glass transition temperature and increasing the amorphous phase of PEO and the fraction of PEO-Li⁺ complex, corresponding to conductivity enhancement. Al₂O₃ filler would contribute to conductivity enhancement by transient hydrogen bonding of migrating ionic species with O–OH groups at the filler grain surface. The differential scanning calorimetry thermograms points towards the decrease of T _g , crystallite melting temperature, and melting enthalpy of PEO: LiTf: Al₂O₃ CPE after introducing plasticizers. The reduction of crystallinity and the increase in the amorphous phase content of the electrolyte, caused by the filler, also contributes to the observed conductivity enhancement.     

Enhanced ionic conductivity in novel nanocomposite gel polymer electrolyte based on intercalation of PMMA into layered LiV3O8

In the present work, a novel polymer electrolyte based on poly(methyl methacrylate) (PMMA)/layered lithium trivanadate (LiV₃O₈) nanocomposite has been investigated. X-ray diffraction (XRD) study shows that d-spacing is increased from 6.3?±?0.1 Å to 12.8?±?0.1 Å upon intercalation of the polymer into the layered LiV₃O₈. Room temperature ionic conductivity of the obtained nanocomposite gel polymer electrolyte is found to be superior to that of conventional PMMA-based gel polymer electrolyte. Enhancement in ionic conductivity of the nanocomposite gel electrolyte is attributed to the formation of a two-dimensional channel as a result of decreased interaction between Li⁺ and V₃O ₈ ^? layers as confirmed by FTIR. SEM results show aggregation of nanocomposite particles resulting from extension of some of the polymer chains from interlayer to the edge providing paths for Li⁺ ion transport. Interfacial stability of nanocomposite gel electrolyte is also found to be better than that of the conventional PMMA-based gel polymer electrolyte.     

A Long‐Life Lithium Ion Battery with Enhanced Electrode/Electrolyte Interface by Using an Ionic Liquid Solution

In this paper, we report an advanced long‐life lithium ion battery, employing a Pyr₁₄TFSI‐LiTFSI non‐flammable ionic liquid (IL) electrolyte, a nanostructured tin carbon (Sn‐C) nanocomposite anode, and a layered LiNi_1/3Co_1/3Mn_1/3O₂ (NMC) cathode. The IL‐based electrolyte is characterized in terms of conductivity and viscosity at various temperatures, revealing a Vogel–Tammann–Fulcher (VTF) trend. Lithium half‐cells employing the Sn‐C anode and NMC cathode in the Pyr₁₄TFSI‐LiTFSI electrolyte are investigated by galvanostatic cycling at various temperatures, demonstrating the full compatibility of the electrolyte with the selected electrode materials. The NMC and Sn‐C electrodes are combined into a cathode‐limited full cell, which is subjected to prolonged cycling at 40 °C, revealing a very stable capacity of about 140 mAh g^?1 and retention above 99 % over 400 cycles. The electrode/electrolyte interface is further characterized through a combination of electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) investigations upon cell cycling. The remarkable performances reported here definitively indicate that IL‐based lithium ion cells are suitable batteries for application in electric vehicles.     

Combined Intrinsic and Extrinsic Proton Conduction in Robust Covalent Organic Frameworks for Hydrogen Fuel Cell Applications

Developing new materials for the fabrication of proton exchange membranes (PEMs) for fuel cells is of great significance. Herein, a series of highly crystalline, porous, and stable new covalent organic frameworks (COFs) have been developed by a stepwise synthesis strategy. The synthesized COFs exhibit high hydrophilicity and excellent stability in strong acid or base (e.g., 12 m NaOH or HCl) and boiling water. These features make them ideal platforms for proton conduction applications. Upon loading with H₃PO₄, the COFs (H₃PO₄@COFs) realize an ultrahigh proton conductivity of 1.13×10^?1 S cm^?1, the highest among all COF materials, and maintain high proton conductivity across a wide relative humidity (40–100 %) and temperature range (20–80 °C). Furthermore, membrane electrode assemblies were fabricated using H₃PO₄@COFs as the solid electrolyte membrane for proton exchange resulting in a maximum power density of 81 mW cm^?2 and a maximum current density of 456 mA cm^?2, which exceeds all previously reported COF materials.     

Spectroscopic and Discharge Studies on Graphene Oxide Doped PVA/PVP Blend Nanocomposite Polymer Films

Graphene oxide (GO) nanoparticles were synthesized by modified Hummers method. The synthesized GO nanoparticles were incorporated in polyvinyl alcohol/polyvinyl pyrrolidone (PVA/PVP) blend polymers for the preparation of nanocomposite polymer films by solution cast technique. Different characterizations such as XRD, UV–Vis and FTIR were carried-out on to the prepared nanocomposite polymer films. The thermal analysis of the films was studied by DSC. The morphology of PVA/PVP:GO polymer films confirms GO was exfoliated within the PVA/PVP matrix and also reveals the heterogeneous phase of nanocomposite polymer electrolyte systems. From the conductivity studies the highest conductivity of PVA/PVP: GO (0.45: 0.3) was found to be 8.05 × 10^–4 S/cm at room temperature. Solid state battery has been fabricated with the configuration of Mg⁺/(PVA/PVP:GO)/(I₂ + C + electrolyte) and its cell parameters were calculated for a constant load of 100 kΩ.     

Enhanced zinc ion transport in gel polymer electrolyte: effect of nano-sized ZnO dispersion

The effect of the dispersion of zinc oxide (ZnO) nanoparticles in the zinc ion conducting gel polymer electrolyte is studied. Changes in the morphology/structure of the gel polymer electrolyte with the introduction of ZnO particles are distinctly observed using X-ray diffraction and scanning electron microscopy. The nanocomposites offer ionic conductivity values of >10^?3 S cm^?1 with good thermal and electrochemical stabilities. The variation of ionic conductivity with temperature follows the Vogel–Tamman–Fulcher behavior. AC impedance spectroscopy, cyclic voltammetry, and transport number measurements have confirmed Zn²⁺ ion conduction in the gel nanocomposites. An electrochemical stability window from ?2.25 to 2.25 V was obtained from voltammetric studies of nanocomposite films. The cationic (i.e., Zn²⁺ ion) transport number (t ₊) has been found to be significantly enhanced up to a maximum of 0.55 for the dispersion of 10 wt.% ZnO nanoparticles, indicating substantial enhancement in Zn²⁺ ion conductivity. The gel polymer electrolyte nanocomposite films with enhanced Zn²⁺ ion conductivity are useful as separators and electrolytes in Zn rechargeable batteries and other electrochemical applications.     

Polymerization-induced microphase separation of polymer-polyoxometalate nanocomposites for anhydrous solid state electrolytes

Solid-state electrolytes (SSEs) with high ionic conductivity, mechanical stability, and high thermal stability, as well as the stringent requirement of application in high-temperature fuel cells and lithium-ion batteries is receiving increasing attention. Polymer nanocomposites (PNCs), combining the advantages of inorganic materials with those of polymeric materials, offer numerous opportunities for SSEs design. In this work, we report a facile and general one-pot approach based on polymerization-induced microphase separation (PIMS) to generate PNCs with bi-continuous microphases. This synthetic strategy transforms a homogeneous liquid precursor consisting of polyoxometalates (POMs, H₃PW₁₂O₄₀, Li₇[V₁₅O₃₆(CO₃)]), poly(ethylene glycol) (PEG) macro-chain-transfer agent, styrene and divinylbenzene monomers, into a robust and transparent monolith. The resulting POMs are uniformly dispersed in the PEG block (PEG/POM) to form a conducting pathway that successfully realizes the effective transfer of protons and lithium ions, while the highly cross-linked polystyrene domains (P(S-co-DVB)) as mechanical support provide outstanding mechanical properties and thermal stability. As the POM loading ratio up to 35 wt%, the proton conductivity of nanocomposite reaches as high as 5.99 × 10^-4 S/cm at 100 °C in anhydrous environment, which effectively promotes proton transfer under extreme environments. This study broadens the application of fuel cells and lithium-ion batteries in extreme environments.     

Nanocomposite solid polymeric electrolyte of 49% poly(methyl methacrylate)-grafted natural rubber–titanium dioxide–lithium tetrafluoroborate (MG49-TiO2-LiBF4)

A nanocomposite polymer electrolyte consisting of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) as a polymer matrix, lithium tetrafluoroborate (LiBF₄) as a dopant salt, and titanium dioxide (TiO₂) as an inert ceramic filler was prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by a sol–gel process. The ionic conductivity was investigated by alternating current impedance spectroscopy. X-ray diffraction (XRD) was used to determine the structure of the electrolyte, and its morphology was examined by scanning electron microscopy (SEM). The highest conductivity, 1.4 × 10⁻⁵ S cm⁻¹ was obtained at 30 wt.% of LiBF₄ salt addition with 6 wt.% of TiO₂ filler content. Ionic conductivity was found to increase with the increase of salt concentration. The optimum value of conductivity was found at 6 wt.% of TiO₂. The XRD analysis revealed that the crystalline phase of the polymer host slightly decreased with the addition of salt and filler. The SEM analysis showed that the smoother the surface of the electrolyte, the higher its conductivity.

     

Nanocomposite solid polymeric electrolyte of 49% poly(methyl methacrylate)-grafted natural rubber�Ctitanium dioxide�Clithium tetrafluoroborate (MG49-TiO2-LiBF4)

A nanocomposite polymer electrolyte consisting of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) as a polymer matrix, lithium tetrafluoroborate (LiBF₄) as a dopant salt, and titanium dioxide (TiO₂) as an inert ceramic filler was prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by a sol?Cgel process. The ionic conductivity was investigated by alternating current impedance spectroscopy. X-ray diffraction (XRD) was used to determine the structure of the electrolyte, and its morphology was examined by scanning electron microscopy (SEM). The highest conductivity, 1.4?×?10^?5 S cm^?1 was obtained at 30 wt.% of LiBF₄ salt addition with 6 wt.% of TiO₂ filler content. Ionic conductivity was found to increase with the increase of salt concentration. The optimum value of conductivity was found at 6 wt.% of TiO₂. The XRD analysis revealed that the crystalline phase of the polymer host slightly decreased with the addition of salt and filler. The SEM analysis showed that the smoother the surface of the electrolyte, the higher its conductivity.     

Nanostructured lithium-free oxyanion cathode, Li x Co2(MoO4)3 [0≤ x <3] for 3 V class lithium batteries

A new nanostructured framework-type polyanion material, Li _x Co₂(MoO₄)₃ [0≤?x?<3], was studied as a positive electrode for use in 3-Volt class lithium-ion cells for the first time. The new material was synthesized in a lithium-free composition and examined its structure, morphology, and electrochemical characteristics. Co₂(MoO₄)₃ was found to crystallize in a monoclinic structure with lattice parameters: a?=?14.280(9) ?, b?=?3.382(8) ?, c?=?10.557(1) ?, and β?=?117.9728° (space group P2/m). The redox behavior of this new material was demonstrated in lithium-containing test cells. The material offered a discharge capacity of approximately 110 mAh g^?1 between 3.5 and 1.5 V during the first cycle and retained 50% capacity at the end of the 20th cycle. The poor capacity retention is obviously attributed to the poor electronic conductivity of Co₂(MoO₄)₃ owing to its open framework structure. To overcome the intrinsic low electronic conductivity of polyanion materials, we have adapted a nanocomposite approach by way of adding nanoporous carbon matrix (particle size approximately 10 nm) together with the conventional conductive additive (acetylene black) and demonstrated that the overall electronic conductivity could be improved significantly, yielding an initial discharge capacity of 121 mAh g^?1 using nanocomposite electrode in the potential range 3.5 V down to 2.0 V.     

Integrated lithium metal anode protected by composite solid electrolyte film enables stable quasi-solid-state lithium metal batteries

Lithium (Li) metal, possessing an extremely high theoretical specific capacity (3860 mAh/g) and the most negative electrode potential (−3.040 V vs. standard hydrogen electrode), is one the most favorable anode materials for future high-energy-density batteries. However, the poor cyclability and safety issues induced by extremely unstable interfaces of traditional liquid Li metal batteries have limited their practical applications. Herein, a quasi-solid battery is constructed to offer superior interfacial stability as well as excellent interfacial contact by the incorporation of Li@composite solid electrolyte integrated electrode and a limited amount of liquid electrolyte (7.5 μL/cm²). By combining the inorganic garnet Al-doped Li_6.75La₃Zr_1.75Ta_0.25O₁₂ (LLZO) with high mechanical strength and ionic conductivity and the organic ethylene-vinyl acetate copolymer (EVA) with good flexibility, the composite solid electrolyte film could provide sufficient ion channels, sustained interfacial contact and good mechanical stability at the anode side, which significantly alleviates the thermodynamic corrosion and safety problems induced by liquid electrolytes. This innovative and facile quasi-solid strategy is aimed to promote the intrinsic safety and stability of working Li metal anode, shedding light on the development of next-generation high-performance Li metal batteries.     

Improvement by heating of the electronic conductivity of cobalt spinel phases, electrochemically synthesized in various electrolytes

The nature of the alkaline electrolyte (based on KOH, NaOH, LiOH), in which Co₃O₄ spinel type phases are synthesized by electrooxidation of CoO, is shown to play a key role on the composition, the structure and the electronic conductivity of the materials. In the materials, prepared in pure LiOH electrolyte or in mixed ternary electrolyte (KOH, NaOH, LiOH), Co⁴⁺ ions are present in the octahedral framework, which entails electronic delocalization in the cobalt T_2g band and a high conductivity. The structure of the sample, synthesized in KOH, is on the opposite closer to that of ideal Co₃O₄, with only Co³⁺ in the octahedral sublattice, which leads to a semi-conducting behavior. Whatever the initial material, a thermal treatment induces an increase of the Co⁴⁺/Co³⁺ ratio in the octahedral network, resulting in a significant increase of the electronic conductivity.     

Ionic conductivity enhancement in the solid polymer electrolyte PEO9LiTf by nanosilica filler from rice husk ash

Rice husk ash is a cheap raw material available in abundance in rice-growing countries. It contains around 85–90 % amorphous silica. Rice husk ash, when subjected to a simple chemical precipitation method, will produce nanosilica which can be used for many industrial and technological applications. In this work, we have successfully synthesized nano-sized silica from local rice husk ash and prepared the nanocomposite solid polymer electrolyte, PEO₉LiTf:SiO₂. The resulting electrolyte has been characterized by X-ray diffraction, differential scanning calorimetry, atomic force microscopy, Fourier transform infrared spectroscopy, and complex impedance spectroscopy. The electrolyte shows about a 12-fold increase in ionic conductivity at room temperature due to the silica filler. In the nanocomposite electrolyte, nanosilica particles obtained from rice husk ash behaved very similarly to the commercial grade nanosilica and had a size distribution in the 25- to 40-nm range. As already suggested by us and by others, the O^2? and OH^? surface groups in the filler surface interact with the Li⁺ ions and provide hopping sites for migrating Li⁺ ions through transient H bonding, creating additional high-conducting pathways. This would contribute to a substantial conductivity enhancement through increased ionic mobility. An additional contribution to conductivity enhancement, particularly at temperatures below 60 °C, appears to come from the increased fraction of the amorphous phase, as evidenced from the reduced crystallite melting temperature and the reduced enthalpy of melting due to the presence of the filler.     

A 3D Nanostructured Hydrogel‐Framework‐Derived High‐Performance Composite Polymer Lithium‐Ion Electrolyte

Solid‐state electrolytes have emerged as a promising alternative to existing liquid electrolytes for next generation Li‐ion batteries for better safety and stability. Of various types of solid electrolytes, composite polymer electrolytes exhibit acceptable Li‐ion conductivity due to the interaction between nanofillers and polymer. Nevertheless, the agglomeration of nanofillers at high concentration has been a major obstacle for improving Li‐ion conductivity. In this study, we designed a three‐dimensional (3D) nanostructured hydrogel‐derived Li_0.35La_0.55TiO₃ (LLTO) framework, which was used as a 3D nanofiller for high‐performance composite polymer Li‐ion electrolyte. The systematic percolation study revealed that the pre‐percolating structure of LLTO framework improved Li‐ion conductivity to 8.8×10^?5 S cm^?1 at room temperature.     

室温离子液体增塑的纳米复合聚合物电解质研究

在室温离子液体N-乙基-N'-甲基咪唑四氟硼酸盐(EMIBF₄)增塑的凝胶聚合物电解质中加入氧化铝纳米粒子, 制备了一种纳米复合聚合物电解质(nanocomposite polymer electrolyte, NCPE). 通过示差扫描量热(DSC)、X射线衍射(XRD)、热重分析(TGA)、电化学阻抗谱(EIS)等手段对其进行了表征. 结果显示, 随着氧化铝纳米粒子含量的增加, NCPE的结晶度降低, 离子导电率升高. 但是, 纳米粒子的加入量过大时反而引起NCPE的离子导电率降低. 当纳米粒子填充量为w＝10%时, NCPE具有最高的室温离子导电率1.25×10^－3 S•cm^－1.     

Optical and dielectric properties of PVP based composite polymer electrolyte films

Solid polymer electrolyte films were prepared by adding Al₂O₃ particles to poly(vinylpyrrolidone)-MgCl₂ ? 6H₂O salt using solution cast technique. Various analytical techniques have been applied to characterize the prepared polymer films such as XRD, SEM, UV–Vis spectroscopy and AC conductivity. The structural analysis of pure poly(vinylpyrrolidone) complexed with MgCl₂ ? 6H₂O salt showed orthorhombic lattice structure indicating its semi-crystalline nature. SEM analysis reveals the heterogeneous phase of nanocomposite polymer electrolyte systems. The conductivity of Al2O3 doped poly(vinylpyrrolidone) based solid polymer electrolyte was found to be 1.22 × 10^–6 S/cm at room temperature for 85: 15 weight composition. Electrochemical cell has been fabricated with the configuration Mg⁺/(PVP + MgCl₂ ? 6H₂O + Al₂O₃)/(I₂ + C + electrolyte) and its discharge characteristics were studied for a constant load of 100 kΩ. Various cell parameters such as open-circuit voltage, short circuit current, energy density and power density were calculated for the prepared samples.     

A Self‐Binding,Melt‐Castable,Crystalline Organic Electrolyte for Sodium Ion Conduction

The preparation and characterization of the cocrystalline solid–organic sodium ion electrolyte NaClO₄(DMF)₃ (DMF=dimethylformamide) is described. The crystal structure of NaClO₄(DMF)₃ reveals parallel channels of Na⁺ and ClO₄^? ions. Pressed pellets of microcrystalline NaClO₄(DMF)₃ exhibit a conductivity of 3×10^?4 S cm^?1 at room temperature with a low activation barrier to conduction of 25 kJ mol^?1. SEM revealed thin liquid interfacial contacts between crystalline grains, which promote conductivity. The material melts gradually between 55–65 °C, but does not decompose, and upon cooling, it resolidifies as solid NaClO₄(DMF)₃, permitting melt casting of the electrolyte into thin films and the fabrication of cells in the liquid state and ensuring penetration of the electrolyte between the electrode active particles.     

Enhanced photoresponse of poly(3-methylthiophene) supported on TiO2

We have investigated the photoelectrochemical behavior of poly(3-methylthiophene) supported on nanostructured n-TiO₂ in a solid-state photoelectrochemical device. As electrolyte we employed the elastomer poly(epichlorohydrin-co-ethylene oxide) filled with NaI/I₂. Under polychromatic light irradiation (60 mW cm⁻²) the device exhibits an open circuit voltage, a short-circuit current and fill factor of 10 μA cm⁻², 0.048 V and 0.29, respectively. The overall efficiency of the cell is 2.3×10⁻²%.