Measurement of the absolute Raman scattering cross sections of sulfur and the standoff Raman detection of a 6‐mm‐thick sulfur specimen at 1500 m

The absolute Raman scattering cross sections (σ_RS) for the 471, 217, and 153 cm⁻¹ modes of sulfur were measured as 6.0 ± 1.2 × 10⁻²⁷, 7.7 ± 1.6 × 10⁻²⁷, and 1.2 ± 0.24 × 10⁻²⁶ cm² at 815, 799, and 794 nm, respectively, using a 785‐nm pump laser. The corresponding values of σ_RS at 1120, 1089, and 1081 nm were determined to be 1.5 ± 0.3 × 10⁻²⁷, 1.2 ± 0.24 × 10⁻²⁷, and 1.2 ± 0.24 × 10⁻²⁷ cm² using a 1064‐nm laser. A temperature‐controlled, small‐cavity (2.125 mm diameter) blackbody source was used to calibrate the signal output of the Raman spectrometers for these measurements. Standoff Raman detection of a 6‐mm‐thick sulfur specimen located at 1500 m from the pump laser and the Raman spectrometer was made using a 1.4‐W, CW, 785‐nm pump laser. Copyright © 2010 John Wiley & Sons, Ltd.     

Measurement of the absolute Raman scattering cross section of the 1584‐cm−1 band of benzenethiol and the surface‐enhanced Raman scattering cross section enhancement factor for femtosecond laser‐nanostructured substrates

The absolute Raman scattering cross section (σ_RS) for the 1584‐cm⁻¹ band of benzenethiol at 897 nm (1.383 eV) has been measured to be 8.9 ± 1.8 × 10⁻³⁰ cm² using a 785‐nm pump laser. A temperature‐controlled, small‐cavity blackbody source was used to calibrate the signal output of the Raman spectrometer. We also measured the absolute surface‐enhanced Raman scattering cross section (σ_SERS) of benzenethiol adsorbed onto a silver‐coated, femtosecond laser‐nanostructured substrate. Using the measured values of 8.9 ± 1.8 × 10⁻³⁰ and 6.6 ± 1.3 × 10⁻²⁴ cm² for σ_RS and σ_SERS respectively, we calculate an average cross‐section enhancement factor (EF) of 0.8 ± 0.3 × 10⁶. Copyright © 2009 John Wiley & Sons, Ltd.     

Photodissociation effects on pulsed laser deposited silver oxide thin films: surface‐enhanced resonance Raman scattering

Temporal Raman scattering measurements with 488, 532 and 632 nm excitation wavelengths and normal Raman studies by varying the power (from 30 W/cm² to 2 MW/cm²) at 488 nm were performed on silver oxide thin films prepared by pulsed‐laser deposition. Initially, silver oxide Raman spectra were observed with all three excitation wavelengths. With further increase in time and power, silver oxide photodissociated into silver nanostructures. High‐intensity spectral lines were observed at 1336 ± 25 and 1596 ± 10 cm⁻¹ with 488 nm excitation. No spectral features were observed with 633 nm excitation. Surface‐enhanced resonance Raman scattering theory is used to explain the complex behavior in the intensity of the 1336/1596 cm⁻¹ lines with varying power of 488 nm excitation. Copyright © 2011 John Wiley & Sons, Ltd.     

Single‐beam coherent anti‐Stokes Raman scattering (CARS) spectroscopy of gas‐phase CO2 via phase and polarization shaping of a broadband continuum

Coherent anti‐Stokes Raman scattering (CARS) spectroscopy of gas‐phase CO₂ is demonstrated using a single femtosecond (fs) laser beam. A shaped ultrashort laser pulse with a transform‐limited temporal width of ∼7 fs and spectral bandwidth of ∼225 nm (∼3500 cm⁻¹) is employed for simultaneous excitation of the CO₂ Fermi dyads at ∼1285 and ∼1388 cm⁻¹. CARS signal intensities for the two Raman transitions and their ratio as a function of pressure are presented. The signal‐to‐noise ratio of the single beam–generated CO₂ CARS signal is sufficient to perform concentration measurements at a rate of 1 kHz. The implications of these experiments for measuring CO₂ concentrations and rapid pressure fluctuations in hypersonic and detonation‐based chemically reacting flows are also discussed. Copyright © 2010 John Wiley & Sons, Ltd.     

Study of Raman spectrum of uranium using a surface‐enhanced Raman scattering technique

Raman spectroscopic investigation on weak scatterers such as metals is a challenging scientific problem. Technologically important actinide metals such as uranium and plutonium have not been investigated using Raman spectroscopy possibly due to poor signal intensities. We report the first Raman spectrum of uranium metal using a surface‐enhanced Raman scattering‐like geometry where a thin gold overlayer is deposited on uranium. Raman spectra are detected from the pits and scratches on the sample and not from the smooth polished surface. The 514.5‐ and 785‐nm laser excitations resulted in the Raman spectra of uranium metal whereas 325‐nm excitation did not give rise to such spectra. Temperature dependence of the B_3g mode at 126 cm⁻¹ is also investigated. Copyright © 2011 John Wiley & Sons, Ltd.     

Spectroscopic analysis of a dye–mineral composite–a Raman and FT‐IR study

In this investigation, we address the question of how organic thioindigo binds to inorganic palygorskite to form a pigment similar to Maya Blue. We also address how such binding, if it occurs, might be affected by varying the proportion of dye relative to that of the mineral, and by varying the length of heating time used in preparation of the pigment. In addition to samples of palygorskite and thioindigo both alone, four synthetic pigment samples were prepared; two samples of 8 wt.% dye, one heated at 170 °C for 3 h and one at 170 °C for 9 h, and two samples of 16 wt.% dye, one heated at 170 °C for 3 h and one at 170 °C for 9 h. All samples were examined using Fourier transform‐infrared (FT‐IR) and FT‐Raman spectroscopy. For the pigment samples, FT‐IR peaks at 1627 cm⁻¹ are attributed to a downshifted CO stretching mode of thioindigo due to dye–clay interaction. This interpretation is corroborated by FT‐Raman CO peaks with 14 cm⁻¹ shifts to lower wavenumber for the pigment relative to thioindigo alone. Additional Raman scattering between 550 cm⁻¹ and 650 cm⁻¹ also suggests dye–clay interaction through metal–oxygen bonding. We are thus led to the possibility of mostly hydrogen bonding between silanol and carbonyl at lower dye concentration, with a predominance of metal–oxygen bonding at higher dye concentration. Copyright © 2008 John Wiley & Sons, Ltd.     

Detection of melamine in liquid milk using surface‐enhanced Raman scattering spectroscopy

Melamine, a nitrogen‐rich chemical, has recently caused enormous economic losses to the food industry due to the cases of milk products adulterated by melamine. This has led to an urgent need of rapid and reliable methods for detection of melamine in food. In this study, surface‐enhanced Raman scattering (SERS) spectroscopy was used to detect melamine in liquid milk. The sample preparation with liquid milk is very easy; it has to be only diluted with double‐distilled water followed by centrifugation. By using a silver colloid, at least a 10⁵‐fold enhancement of the Raman signal was achieved for the measurement of melamine. The limit of detection by this method was 0.01 µg ml⁻¹ for melamine standard samples. Based on the intensity of the Raman vibrational bands normalised to that of the band at 928 cm⁻¹ (CH₂), an external standard method was employed for quantitative analysis. The linear regression square (R²) of the curve was 0.9998; the limit of quantitation using this approach was 0.5 µg ml⁻¹ of melamine in liquid milk; the relative standard deviation was ≤10%; and recoveries were from 93 to 109%. The test results for SERS were very precise and as good as those obtained by liquid chromatography/tandem mass spectrometry. The method was simple, fast(only needs about 3 min), cost effective, and sensitive for the detection of melamine in liquid milk samples. Therefore, it is more suitable for the field detection of melamine in liquid milk. Copyright © 2010 John Wiley & Sons, Ltd.     

Pump power dependence in resonance femtosecond stimulated Raman spectroscopy

Femtosecond stimulated Raman spectroscopy (FSRS) has emerged as a powerful new technique that is capable of obtaining resonance Raman spectra of fluorescent species and transient photochemical intermediates. Unlike related transient infrared absorption techniques, the FSRS signal is quite sensitive to the laser power utilized in the vibrational probing event. In particular, FSRS spectra are highly sensitive to the intensity of the picosecond Raman‐pump pulse. We have measured the power dependence of the FSRS signal using pulse energies from ~10⁻⁹ to ~10⁻⁵ J and molecules with a range of molar absorptivities at the Raman‐pump wavelength of 400 nm, including β‐carotene (ε₄₀₀ = 58 300 M⁻¹ cm⁻¹), para‐nitroaniline (17 800 M⁻¹ cm⁻¹), nitronaphthalene (247 M⁻¹ cm⁻¹) and ferrocene (57 M⁻¹ cm⁻¹). We show that for strongly absorbing molecular systems, such as β‐carotene and para‐nitroaniline, the ground‐state (GS) FSRS signal actually decreases with increasing pump power at pump fluences above ~10⁻² J cm⁻², due to depletion of the GS population. However, for weakly absorbing species like nitronaphthalene and ferrocene, the signal increases linearly with increasing pump fluence until ~0.5 J cm⁻², at which point two‐photon absorption by the solute induces nonlinear absorption of the pump pulse and attenuation of the FSRS signal. The data are quantitatively simulated with a photophysical kinetic model, and the results are analyzed to provide simple guidelines for acceptable Raman‐pump powers in resonance FSRS experiments. The acceptable Raman‐pump power is proportional to the focused beam area and depends inversely on the sample's molar absorptivity. Copyright © 2013 John Wiley & Sons, Ltd.     

Nature of some features in Raman spectra of hydroxyapatite‐containing materials

A very broad vibrational band ranging from 1000 up to 4000 cm⁻¹ and two relatively sharp bands at 5000 and 5027 cm⁻¹ are found in the Raman scattering spectrum of hydroxyapatite‐containing films obtained by gas detonation spray method. We developed a theoretical model that interprets the broad band as a result of strong interaction between the high‐frequency hydrogen bond vibrations and lattice phonons. Both sharp bands around 5000 cm⁻¹ are assigned to the overtones of v‐OH vibrations. Copyright © 2016 John Wiley & Sons, Ltd.     

Study of carrier concentration profiles in Al‐implanted Ge by micro‐Raman spectroscopy under different excitation wavelengths

The distribution profile of Al implanted in crystalline Ge has been investigated by micro‐Raman spectroscopy. Using different excitation laser lines, corresponding to different optical penetration depths, the Al concentration at different depths beneath the sample surface has been studied. We have found a strong correlation between the intensity of the Al–Ge Raman peak at ~370 cm⁻¹, which is due to the local vibrational mode of substitutional Al atoms, and the carrier concentration profile, obtained by the spreading resistance profiling analysis. A similar connection has been also observed for both shape and position of the Ge–Ge Raman peak at ~300 cm⁻¹. According to these experimental findings, we propose here a fast and nondestructive method, based on micro‐Raman spectroscopy under different excitation wavelengths, to estimate the carrier concentration profiles in Al‐implanted Ge. Copyright © 2013 John Wiley & Sons, Ltd.     

Observation of low‐wavenumber out‐of‐plane optical phonon in few‐layer graphene

Few‐layer graphene grown by chemical vapor deposition has been studied by Raman and ultrafast laser spectroscopy. A low‐wavenumber Raman peak of ~120 cm⁻¹ and a phonon‐induced oscillation in the kinetic curve of electron–phonon relaxation process have been observed, respectively. The Raman peak is assigned to the low‐wavenumber out‐of‐plane optical mode in the few‐layer graphene. The phonon band shows an asymmetric shape, a consequence of so‐called Breit‐Wigner‐Fano resonance, resulting from the coupling between the low‐wavenumber phonon and electron transitions. The obtained oscillation wavenumber from the kinetic curve is consistent with the detected low‐wavenumber phonon by Raman scattering. The origin of this oscillation is attributed to the generation of coherent phonons and their interactions with photoinduced electrons. Copyright © 2012 John Wiley & Sons, Ltd.     

Heterodyne interferometric polarization coherent anti‐Stokes Raman scattering (HIP‐CARS) spectroscopy

We demonstrate a new technique that combines polarization sensitivity of the coherent anti‐Stokes Raman scattering (CARS) response with heterodyne amplification for background‐free detection of CARS signals. In this heterodyne interferometric polarization CARS (HIP‐CARS), the major drawbacks of polarization and heterodyne CARS are rectified. Using a home‐built picosecond optical parametric oscillator, we are able to address vibrational stretches between 600 and 1650 cm⁻¹ and record continuous high‐resolution Raman equivalent HIP‐CARS spectra. Copyright © 2010 John Wiley & Sons, Ltd.     

Origin of the Raman mode at 379 cm−1 observed in ZnO thin films grown on sapphire

In this work, we present a detailed Raman scattering study to clarify the origin of the mode at 379 cm⁻¹ which is observed in Raman spectra of the ZnO films grown on c‐sapphire substrates and generally attributed to the A₁‐transverse optical (A₁‐TO) mode of ZnO. The studied ZnO films were deposited by metal‐organic chemical vapor deposition on c‐sapphire and (0001) ZnO substrates. In the z(−,−)z̄ backscattering configuration, the A₁‐TO mode is forbidden, while the 379 cm⁻¹ peak is still observed in the as‐deposited film grown on sapphire substrate. However, this mode is not observed in Raman spectra of the as deposited film grown on ZnO substrate. We suggest that the peak at 379 cm⁻¹ is the E_1g mode of the sapphire substrate which is allowed in z(−,−)z̄ backscattering configuration. The effects of annealing, the substrate and the collection cross‐section on Raman active modes were analyzed. Copyright © 2011 John Wiley & Sons, Ltd.     

Ag‐nanoparticle‐modified single Ag nanowire for detection of melamine by surface‐enhanced Raman spectroscopy

Silver nanowires synthesized by a solvothermal method were used as templates for fabricating silver‐nanoparticle‐decorated silver (AgNP/Ag) nanowires. The number density and particle size of Ag nanoparticles can be controlled by varying the concentration of Ag precursor. Single AgNP/Ag nanowire exhibited strong surface‐enhanced Raman scattering effect. Detection of melamine molecules at concentrations as low as 1.0 × 10⁻⁸ M was used as an example to show the possible applications of such AgNP/Ag nanowires. Their application in rapid detection of melamine in milk solution was further demonstrated. It was shown that melamine in milk solution at a low concentration of 5.0 × 10⁻⁸ M can be easily detected with little sample pretreatment. The results demonstrate the potential of single AgNP/Ag nanowire as a surface‐enhanced Raman scattering substrate for convenient and sensitive detection of trace amounts of melamine in a complex mixture. Copyright © 2012 John Wiley & Sons, Ltd.     

Single‐molecule detection of thionine on aggregated gold nanoparticles by surface enhanced Raman scattering

We report observations of single‐molecule detection of thionine and its dynamic interactions on aggregated gold nanoparticle clusters using surface enhanced Raman scattering (SERS). Spectral intensities were found to be independent of the size of Au nanoparticles studied (from 17 to 80 nm) at thionine concentration below 10⁻¹² M or at single‐molecule concentration levels. Raman line separations and, in particular, spectral fluctuations and blinking were also observed, suggesting temporal changes in single molecular motion and/or arrangements of thionine on Au nanoparticle surfaces. In contrast, by using dispersed Au nanoparticles, only ensemble SERS spectra could be observed at relatively high concentrations (> 10⁻⁸ M thionine), and spectral intensities varied with the size of Au nanoparticles. Copyright © 2007 John Wiley & Sons, Ltd.     

Structural modifications of GaN after cerium implantation

Among the family of rare earth (RE) dopants, the doping of first member Ce into GaN is the least studied system. This article reports structure properties of Ce‐doped GaN realized by technique of ion implantation. Ce ions were implanted into metal organic chemical vapor deposition grown n‐ and p‐GaN/sapphire thin films at doses 3 × 10¹⁴ and 2 × 10¹⁵ cm⁻². X‐ray diffraction scans and Raman scattering measurements exhibited expansion of lattice in the implanted portion of the samples. First order Raman scattering spectra show appearance of several disorder‐activated Raman scattering modes in addition to typical GaN features. A dose‐dependent decrease in intensity of E₂ mode was observed in Raman the spectra of the implanted samples. Ultraviolet Raman spectra of implanted samples show complete quenching of photoluminescence emission and appearance of multiple A₁(LO) phonon scattering modes up to fifth order. Moreover, a decrease in intensity and an increase in line width of LO modes as a function of wavenumber were observed for implanted samples. Copyright © 2012 John Wiley & Sons, Ltd.     

Layer‐dependent resonant Raman scattering of a few layer MoS2

We report resonant Raman scattering of MoS₂ layers comprising of single, bi, four and seven layers, showing a strong dependence on the layer thickness. Indirect band gap MoS₂ in bulk becomes a direct band gap semiconductor in the monolayer form. New Raman modes are seen in the spectra of single‐ and few‐layer MoS₂ samples which are absent in the bulk. The Raman mode at ~230 cm⁻¹ appears for two, four and seven layers. This mode has been attributed to the longitudinal acoustic phonon branch at the M point (LA(M)) of the Brillouin zone. The mode at ~179 cm⁻¹ shows asymmetric character for a few‐layer sample. The asymmetry is explained by the dispersion of the LA(M) branch along the Γ‐M direction. The most intense spectral region near 455 cm⁻¹ shows a layer‐dependent variation of peak positions and relative intensities. The high energy region between 510 and 645 cm⁻¹ is marked by the appearance of prominent new Raman bands, varying in intensity with layer numbers. Resonant Raman spectroscopy thus serves as a promising non invasive technique to accurately estimate the thickness of MoS₂ layers down to a few atoms thick. Copyright © 2012 John Wiley & Sons, Ltd.     

Near‐infrared Raman spectroscopy for gastric precancer diagnosis

Raman spectroscopy is a molecular vibrational spectroscopic technique that is capable of optically probing the biomolecular changes associated with neoplastic transformation. The purpose of this study was to apply near‐infrared (NIR) Raman spectroscopy for differentiating dysplasia from normal gastric mucosa tissue. A total of 65 gastric mucosa tissues (44 normal and 21 dysplasia) were obtained from 35 patients who underwent endoscopy investigation or gastrectomy operation for this study. A rapid NIR Raman system was utilized for tissue Raman spectroscopic measurements at 785‐nm laser excitation. High‐quality Raman spectra in the range of 800–1800 cm⁻¹ can be acquired from gastric mucosa tissue within 5 s. Raman spectra showed significant differences between normal and dysplastic tissue, particularly in the spectral ranges of 850–1150, 1200–1500 and 1600–1750 cm⁻¹, which contained signals related to proteins, nucleic acids and lipids. The diagnostic decision algorithm based on the combination of Raman peak intensity ratios of I₈₇₅/I₁₄₅₀ and I₁₂₀₈/I₁₆₅₅ and the logistic regression analysis yielded a diagnostic sensitivity of 90.5% and specificity of 90.9% for identification of gastric dysplasia tissue. This work demonstrates that NIR Raman spectroscopy in conjunction with intensity ratio algorithms has the potential for the noninvasive diagnosis and detection of precancer in the stomach at the molecular level. Copyright © 2009 John Wiley & Sons, Ltd.     

Raman mode‐selective spectroscopic imaging of coenzyme and enzyme redox states

We investigate the surface‐enhanced Raman scattering (SERS) spectra of flavin monoucleotide (FMN) in its different redox states and in a redox active enzyme, nitric oxide synthase. Incubated with silver nanoparticles coated with silica, spectra for oxidized and reduced FMN are obtained at different electrochemical potentials. Dominate Raman mode shifts at 1623/1610, 1567/1550, and 1502/1492 cm⁻¹, belonging to typical redox‐sensitive region of FMN, are observed and analyzed, and they show a consistence with the results of spectral calculation by using the density function theory (DFT) method. We assign mode at 1500 cm⁻¹, composed of N₅―H bending, N₁C_10a stretching and the asymmetric C_4a―N₅―C_5a stretching, as a spectroscopic indicator for the redox states of FMN, because it shows a significant downshift (1502/1492 cm⁻¹) and non‐linearly correction with potentials when FMN gets reduced from its full oxidized state electrochemically. Isolated FMN domain from a wild type neuronal nitric oxide synthase enzyme (nNOS) is also studied with the same experimental approach. We have observed similar Raman mode down‐shifting as that of the pure FMN, which further supports our conclusion that the mode at ~1500 cm⁻¹ indicates redox states for FMN, the coenzyme of nNOS, even in redox protein matrix. Copyright © 2016 John Wiley & Sons, Ltd.