Crystal growth of zirconium‐doped KTiOPO4 crystals in the K2O‐P2O5‐TiO2‐ZrF4 system

Zirconium‐doped KTiOPO₄ (KTP) crystals were grown using a high temperature flux method in the K₂O‐P₂O₅‐TiO₂‐ZrF₄ system. The dopant content in the single crystals with general composition KTi_1‐xZr_xOPO₄ (where x = 0 – 0.026) strongly depends on zirconium concentration in the homogeneous melts. AES‐ICP method and X‐ray fluorescence analysis were used to determine the composition of the obtained crystals. Phase analyses of the products were performed using the powder XRD. The structures of KTiOPO₄ containing different quantities of Zr were refined on the basis of single crystal XRD data. Applying ZrF₄ precursor for zirconium injection into the flux allowed growing the zirconium‐doped KTP crystals at 930–750°C. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical and magnetic properties of Nd‐doped ZnO nanoparticles

Nd‐doped ZnO nanoparticles with different concentration were synthesized by sol‐gel method. The structures, magnetic and optical properties of as‐synthesized nanorods were investigated. X‐ray diffraction (XRD) and x‐ray photoelectron spectroscopy (XPS) results demonstrated that Nd ions were incorporated into ZnO lattice; but Zn_1‐xNd_xO nanoparticles with Nd concentration of x = 0.05 showed Nd₂O₃ phase, so the saturation concentration of Nd in Zn_1‐xNd_xO is less than 5 at%. Vibrating sample magnetometer (VSM) measurements indicated that Nd doped ZnO possessed dilute ferromagnetis behaviour at room temperature. Photoluminescence spectroscopy (PL) showed that Nd ions doping induced a red slight shift and decrease in UV emission with increase of Nd concentration.     

Near‐stoichiometric LiNbO3:ZrO2 single crystal growth by micro pulling down method

Crack‐free, rod‐shaped single crystals of undoped and 0.5, 0.7 and 1.0 mol% ZrO₂‐doped LiNbO₃ with a near‐stoichiometric composition were grown by the micro‐pulling down (μ‐PD) method. The structural properties of the grown crystals were examined by powder X‐ray diffraction (XRD). Electron probe micro analysis (EPMA) of the near‐stoichiometric LiNbO₃ single crystals revealed the homogeneous incorporation of Zr ions. The change in the refractive index and IR transmission spectra of the grown crystals were examined as a function of the Zr concentration. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

α‐Fe2O3 nanospindles loaded with ZnO nanocrystals: Synthesis and improved gas sensing performance

ZnO/α‐Fe₂O₃ nanocomposites were fabricated through a two‐step hydrothermal method. The morphology and composition of the as‐synthesized products were characterized by X‐ray powder diffraction (XRD), field emission scanning electron microscopy (FESEM), energy‐dispersive X‐ray spectroscopy (EDS), transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM). The gas sensing properties of the fabricated products were investigated towards ethanol, acetone, propanol, isopropanol, formaldehyde, chloroform and so on. The results demonstrated that the ZnO/α‐Fe₂O₃ nanocomposites exhibited excellent sensing properties and showed remarkably higher sensing responses and much lower optimum operating temperature compared to individual ZnO and α‐Fe₂O₃. In addition, the ZnO/α‐Fe₂O₃ nanocomposites have some selectivity for ethanol, propanol and isopropanol. The possible gas sensing mechanism was also proposed. Our studies demonstrate that our fabricated materials could be widely used in the future.     

Novel nontoxic nanopigments based on zirconia and rare earth mixed oxides

This paper embodies the result of the investigations carried out on the synthesis of zirconia‐ rare earth mixed oxide pigments: ZrCe_1‐xY_xO_4‐δ and ZrCe_1‐xPr_xO_4‐δ by the solution combustion method and their characterization by X‐ray powder diffraction, transmission electron microscopy, energy dispersive spectrometric analysis, thermal analysis, reflectance spectral data and surface area measurements. The synthesized nano pigments possess low a and high b and exhibit yellow color when doped with Y and changes from yellow to orange‐red color when doped with Pr, with increase in x values. These pigments show maximum reflectance of 90% when the wavelength is above 550 nm. Due to the homogeneity of the phase formed and resistance to water, acids and alkali, the rare earth mixed oxides developed are found to be promising candidates as nontoxic pigments. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Flux growth and characterization of Ti‐ and Ni‐doped forsterite single crystals

Forsterite monocrystals doped with Ti and Ni were grown by the flux growth technique. A suitable mixture of flux (MoO₃, V₂O₅, Li₂CO₃) and nutrient was slowly cooled down to 750 °C from 1250 °C or 1350 °C. The crystals were then characterized by powder and single‐crystal X‐ray diffraction, scanning electron microscopy and differential scanning calorimetry (DSC). Variations observed in crystal size were attributed by both the varying experimental conditions in which they had been obtained, and to the amount of Ni substituted for Mg in the structure. High abundances of doped forsterite required a cooling rate of 1.8 K h^‐1. These synthetic, well‐characterized Ti and Ni doped forsterite crystals may have potential for exploitation in industrial fields. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Capsule‐like α‐Fe2O3 nanoparticles: Synthesis,characterization, and growth mechanism

Uniform capsule‐like α‐Fe₂O₃ particles were synthesized via a simple hydrothermal method, employing FeCl₃ and CH₃COONa as the precursors and sodium dodecyl sulfate (SDS) as soft template. X‐ray powder diffraction (XRD), field emission scanning electron microscopy (FE‐SEM), transmission electron microscopy (TEM), and high‐resolution transmission electron microscopy were used to characterize the structure of synthesized products. Some factors influencing the formation of capsule‐like α‐Fe₂O₃ particles were systematically investigated, including different kinds of surfactants, the concentration of SDS, and reaction times. The investigation on the evolution formation reveals that SDS was critical to control the morphology of final products, and a possible five‐step growth mechanism was presented by tracking the structures of the products at different reaction stages.     

Heat‐treatment influence on the microstructure and magnetic properties of rare‐earth substituted SrFe12O19

Rare‐earth substituted strontium ferrite nanopowders SrFe_12‐xR_xO₁₉ (R = La, Gd and Er; x = 0.2, 0.5 and 1) were prepared by sol‐gel‐autocombustion method and subsequent heat treatments. Structural and magnetic properties of SrFe_12‐xR_xO₁₉ powders heat treated at 800, 900 and 1000⁰C, for various times, were characterized with an X‐ray diffractometer, a vibrating sample magnetometer and a scanning electron microscope. The results of X‐ray diffraction measurements showed the M‐type hexagonal structure formation by heat treatments. Magnetic properties, such as specific saturation magnetization σ_s, specific remanent magnetization σ_r and coercivity H_c, as well as microstructure depend on the heat treatment conditions (temperature and time). The coercivity H_c exhibits a great increase after a critical heat treatment time. When the heat treatment time increases, one obtains an increase in H_c after a shorter heat treatment time. This jump of H_c was explained by a transition from the superparamagnetic state to normal state of the single domain nanoparticles. The occurrence of an agglomerated structure composed of magnetically interacting ultrafine crystallites also contributes to the increase of H_c.The heat treatment determines a reduced grain growth due to the internal stress generated by R ions. With increasing R content the σ_s and σ_r decrease due to the dissolution of R ions into the hexaferrite lattice. We believe that by selecting the time and temperature of the heat treatment, microstructure and magnetic properties suitable for magnetic recording media application can be obtained. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Ag@Fe3O4 nanowire: fabrication,characterization and peroxidase‐like activity

With a facile solvothermal method, Ag@Fe₃O₄ nanowire was successfully prepared and characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The obtained Ag@Fe₃O₄ nanowire posses enhanced peroxidase‐like activity with good stability and high absorbance. The optimization of pH, H₂O₂ concentration and loading capacity were carried out. The result of kinetic analysis indicates that the catalyzed reaction followed a Michaelis‐Menten behavior. The good peroxidase‐like activity makes Ag@Fe₃O₄ nanowire be promising for real application in biomedicine.     

Self‐template hydrothermal synthesis ZnS microspheres

Zinc sulfide (ZnS) microspheres were synthesized by a self‐template hydrothermal route using thiourea as sulphur source. The formation of these hollow spheres was mainly attributed to the oriented aggregation of ZnS nanocystals around the gas‐liquid interface between gas (H₂S, NH₃, or CO₂) and water followed by an Ostwald ripening process. The gas bubbles of H₂S, NH₃, or CO₂ produced during the reaction might play a soft‐template to form ZnS hollow microspheres. The products were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), electron diffraction (ED), and photoluminescence (PL). The crystal structure of prepared ZnS microspheres is hexagonal phase polycrystalline. The average microspheres diameter is 1.5 ‐ 6 µm. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Some structural considerations on the perovskite‐type A1‐ySryCo1‐xFexO3‐δ solid solution series

Solid solution series of La_1‐ySr_yCo_1‐xFe_xO_3‐δ were extensively studied in the past as cathode materials for solid oxide fuel cells. However, the crystal structure behavior of La_1‐ySr_yCo_1‐xFe_xO_3‐δ solid solution series when La‐ions are replaced with another rare‐earth ion or metallic alkaline earth metal is at present not fully understood. Here we report X‐ray powder diffraction measurements performed on samples of the Sm_0.8Sr_0.2Co_1‐xFe_xO_3‐δ solid solution series. This study demonstrates that the average A‐cation radius, as well as the Fe content (x), affects the structural modification of the A_1‐ySr_yCo_1‐xFe_xO_3+δ solid solution series significantly. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and tribological properties of Mo‐doped WSe2 Nanolamellars

The Mo‐doped WSe₂ nanolamellars have been successfully prepared via solid‐state thermal (750 °C) reaction between micro‐sized W, Mo with Se powders under inert atmosphere in a closed reactor and characterized by X‐ray diffractometer (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It was found that the morphologies of the as‐prepared products changed from microplates to nanolamellars to aggregations composed of nanoparticles with the doping of Mo powders. And the sizes of crystallites evidently reduced while the contents of dopant increased within a certain limit (1 wt.%–7 wt.%). The tribological properties of the as‐prepared products as additives in HVI750 base oil were investigated by UMT‐2 multispecimen tribotester. The friction coefficient of the base oil containing Mo‐doped WSe₂ nanolamellars was lower and more stable than that of WSe₂ nanolamellars. A combination of rolling friction, sliding friction, and stable tribofilm on the rubbing surface could further explain the good friction and wear properties of Mo‐WSe₂ nanoparticles as additives than that of WSe₂.     

Growth and characterization of large La1‐xPbxMnO3+δ (x=0.32–0.35) crystals

Large crystals of La_0.63Pb_0.37Mn O_3+δ with small La(Pb)‐ deficiency of about 0.005‐0.01 at.% were grown by high temperature solution growth method. The structure of the grown crystals was determined as rhombohedral with R‐3 space group by single‐crystal X‐ray diffractometry. The surface morphology of the crystals and the exact chemical composition was examined by scanning electron microscopy and energy dispersive X‐ray analysis methods, respectively. The IR‐transmission spectrum reveals the presence of Mn³⁺O₆‐ and Mn⁴⁺O₆‐ octahedra in the lattice of La_0.63Pb_0.37Mn O_3+δ crystals. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Evolution of real structure in Ge‐Si mosaic crystals

The structure and properties of Czochralski (Cz)‐grown Ge_1‐xSi_x mosaic crystals were investigated using optical microscopy, atomic force microscopy, X‐ray diffraction analysis, microprobe analysis, FTIR and transmission electron microscopy. The role of segregation, form of solid‐liquid interface and dislocation generation in the development of mosaic structure were analyzed and used for optimization of growth parameters such as Si concentration and growth rate. The dislocation density estimated experimentally was compared with the calculated data. Composition fluctuations caused by formation of cellular structure at the interface lead to a local lattice misorientation that is one of the reasons for crystal mosaicity. Model of mosaic structure generation in terms of dislocation density and composition variations is presented.     

Synthesis of spindle‐shaped α‐FeOOH and α‐Fe2O3 nanocrystals

Spindle‐shaped α‐FeOOH nanocrystals were facilely synthesized using a poly (vinyl pyrrolidone) (PVP)‐assisted route under hydrothermal conditions. The chemical compositions and morphol‐ogies of the as‐prepared samples were characterized in detail by X‐ray power diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscope (TEM). The experimental results reveal that these spindle‐shaped α‐FeOOH nanocrystals have self‐organized into assemblies with hierarchical nanostructures. The crucial roles of PVP in the hydrothermal synthesis of hierarchical α‐FeOOH nanostructures were discussed. The possible formation mechanism was also suggested. Moreover, the spindle‐shaped α‐Fe₂O₃ nanocrystals could be easily obtained after calcining the α‐FeOOH prepared by the PVP‐assisted hydrothermal process. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Facile morphology‐controlled hydrothermal synthesis of flower‐like self‐organized ZnO architectures

Flower‐like self‐organized crystalline ZnO architectures were obtained through a facile and controlled hydrothermal process. As‐synthesized products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), high‐resolution transmission electron microscopy (HRTEM), X‐ray diffraction (XRD), electron diffraction and UV‐Vis spectroscopy. XRD and electron diffraction results confirmed the obtained materials are pure wurtzite ZnO. The effects of different ratios of starting materials and solvent on the morphologies of ZnO hydrothermal products were also evaluated by SEM observations. It is suggested that the use of water, rather than ethanol as the solvent, as well as employing a precursor of Zn(Ac)₂ and 2NaOH (v/v) in hydrothermal reactions are responsible for the generation of specific flower‐like self‐assembled ZnO structures. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Rapid synthesis of dendrite‐ and platelet‐like α‐Fe2O3 via a hydrothermal oxidation route

Dendrite and platelet‐like α‐Fe₂O₃ microcrystals were synthesized by the oxidation reaction of K₄Fe(CN)₆and NaClO₃ through a simple hydrothermal method. The structures and morphologies of the as‐prepared samples were characterized in detail by X‐ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The experiment results show that NaOH played an important role in controlling the morphology of the final products. The possible mechanism was discussed to elucidate the formation of different morphologies of the α‐Fe₂O₃ microstructures. Besides, the magnetic property of the dendrite α‐Fe₂O₃ microstructure was characterized by a vibrating sample magnetometer (VSM). (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Increased optical damage resistance of Zr:LiNbO3 crystals

Zr: LiNbO₃ crystals has been grown. The crystal composition and phase are analyzed by X‐ray diffration. The optical damage resistance ability of Zr: LiNbO₃ crystals is studied by the Sénarmont compensation method and the transmitted beam pattern distortion method. The saturated value of the birefringence change of 6 mol% Zr: LiNbO₃ crystal is 1.01×10^‐4, which is seven times smaller than that of congruent pure LiNbO₃ crystal. The results of UV‐Visible and IR absorption spectra of Zr: LiNbO₃ crystals powerfully confirm that the optical damage resistance threshold concentration of the Zr⁴⁺ ions doped in LiNbO₃ crystals is about 6 mol% in the melt. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Properties of Sm‐doped CaNb2O6 thin films deposited by radio‐frequency magnetron sputtering

Sm‐doped CaNb₂O₆ (CaNb₂O₆:Sm) phosphor thin films were prepared by radio‐frequency magnetron sputtering on sapphire substrates. The thin films were grown at several growth temperatures and subsequently annealed at 800 °C in air. The crystallinity, surface morphology, optical transmittance, and photoluminescence of the thin films were investigated by X‐ray diffraction, scanning electron microscopy, ultraviolet‐visible spectrophotometry, and fluorescence spectrophotometry, respectively. All of the thin films showed a main red emission radiated by the transition from the ⁴G_5/2 excited state to the ⁶H_9/2 ground state of the Sm³⁺ ions and several weak bands under ultraviolet excitation with a 279 nm wavelength. The optimum growth temperature for depositing the high‐quality CaNb₂O₆:Sm thin films, which was determined from the luminescence intensity, was found to be 400 °C, where the thin film exhibited an orthorhombic structure with a thickness of 370 nm, an average grain size of 220 nm, a band gap energy of 3.99 eV, and an average optical transmittance of 85.9%. These results indicate that the growth temperature plays an important role in controlling the emission intensity and optical band gap energy of CaNb₂O₆:Sm thin films.     

PMA‐b‐PAA‐controlled synthesis of one‐dimensional CaCO3 superstructures

Crystallization of calcium carbonate (CaCO₃) crystals by a gas‐liquid diffusion method has been carried out in aqueous solution using a double‐hydrophilic block copolymer (DHBC) poly(maleic anhydride)‐b‐poly(acrylic acid) (PMA‐b‐PAA). The as‐prepared products were characterized with X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), selected area electron diffraction (SAED), high‐resolution transmission electron microscopy (HRTEM) and infrared spectroscopic analysis (FT‐IR). Uniform one‐dimensional calcite micro/nanostructures with different morphologies are fabricated through an assembled process. The influence of PMA‐b‐PAA copolymer concentration on the morphology of calcite nano/microwires is investigated, which plays an important role in the morphological control of building blocks composed of one‐dimensional calcite crystals. The possible formation mechanism of one‐dimensional CaCO₃ crystals was discussed. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)