Subnanomolar Detection of Oligonucleotides through Templated Fluorogenic Reaction in Hydrogels: Controlling Diffusion to Improve Sensitivity

Oligonucleotide‐templated reactions are valuable tools for nucleic acid sensing both in vitro and in vivo. They are typically carried out under conditions that make any reaction in the absence of template highly unfavorable (most commonly by using a low concentration of reactants), which has a negative impact on the detection sensitivity. Herein, we report a novel platform for fluorogenic oligonucleotide‐templated reactions between peptide nucleic acid probes embedded within permeable agarose and alginate hydrogels. We demonstrate that under conditions of restricted mobility (that is, limited diffusion), non‐specific interactions between probes are prevented, thus leading to lower background signals. When applied to nucleic acid sensing, this accounts for a significant increase in sensitivity (that is, lower limit of detection). Optical nucleic acid sensors based on fluorogenic peptide nucleic acid probes embedded in permeable, physically crosslinked, alginate beads were also engineered and proved capable of detecting DNA concentrations as low as 100 pm .     

Amphiphilic membranes with controlled mesh dimensions for insulin delivery+

A series of amphiphilic networks (membranes), consisting of hydrophilic poly(N,N‐dimethylacrylamide) (PDMAAM) main chains crosslinked by hydrophobic telechelic polyisobutylene di‐ and trimethacrylates (MA‐PIB‐MA or ∅︁(PIB‐MA)₃) have been synthesized and used for the preparation of thin‐walled tubules suitable for the immunoisolation of porcine islets. The molecular weight cut‐off (MWCO) ranges, insulin and glucose diffusion coefficients and permeabilities of various membranes have been determined. The molecular weight of the PDMAAM moiety between two hydrophobic crosslinking points (M_{c,hydrophilic}) controls permeability, which in turn can be controlled by synthesis conditions. The strengths and elongations of water‐swollen membranes crosslinked with ∅︁(PIB‐MA)₃ are superior by a factor of about two to those prepared with MA‐PIB‐MA. Based on the values from these experiments, a well‐defined membrane prepared with ∅︁(PIB‐MA)₃ was selected and used to encapsulate porcine islet cells. Gratifyingly, the encapsulated islet cells remain functional and viable, and cells within the tubule release insulin upon glucose challenge. These in vitro experiments are sufficiently promising to encourage us to continue our studies to develop a bioartificial pancreas.     

Preparation,properties, and application of polypropylene micro/nanofiber membranes

Nanofiber membranes have huge potential applications in many areas due to their unique properties. However, the thermoplastic micro/nanofiber membranes were rarely reported. In this paper, polypropylene (PP) nanofibers were prepared by melt extrusion of immiscible blends of PP, cellulose acetate butyrate (CAB), and subsequent removal of the CAB matrix. The wet‐laid application was used to make PP nanofiber membranes and PP‐g‐MAH/nonwoven micro/nanofiber membrane. The properties of membranes including morphology, apparent density, porosity, contact‐angle, pore size distribution, and water flux were characterized. The results showed that the consequent membranes were provided with optimistic porosity and pore size distribution. Moreover, they were all with high pure water fluxes, which were superior to that of PP microporous membrane. They performed an excellent separation performance of TiO₂ suspension and dyeing wastewater. The work revealed this method could be an efficient one to make thermoplastic polymer micro/nanofiber membranes, and they would have a brilliant potential application for water treatment. Copyright © 2010 John Wiley & Sons, Ltd.     

Multicomponent ballistic transport in narrow single wall carbon nanotubes: analytic model and molecular dynamics simulations

The transport of gas mixtures through molecular-sieve membranes such as narrow nanotubes has many potential applications, but there remain open questions and a paucity of quantitative predictions. Our model, based on extensive molecular dynamics simulations, proposes that ballistic motion, hindered by counter diffusion, is the dominant mechanism. Our simulations of transport of mixtures of molecules between control volumes at both ends of nanotubes give quantitative support to the model's predictions. The combination of simulation and model enable extrapolation to longer tubes and pore networks.     

Hydrogel Membrane Improves Batch‐to‐Batch Reproducibility of an Enzymatic Glucose Biosensor

A permselective membrane is a critical component that defines the linear detection limits, the sensitivity, and thus the ultimate efficacy of an enzymatic biosensor. Although membranes like epoxy‐polyurethane (epoxy‐PU) and Nafion are widely used and provide the desired glucose detection limits of 2 to 30 mM, both the within batch and batch‐to‐batch variability of sensors that use these materials is a concern. The hypothesis for this study was that a crosslinked hydrogel would have a sufficiently uniform porosity and hydrophilicity to address the variability in sensor sensitivity. The hydrogel was prepared by crosslinking di‐hydroxyethyl methacrylate, hydroxyethyl methacrylate and N‐vinyl pyrrolidone with 2.5 mol% ethylene glycol dimethacrylate using water soluble initiators – ammonium persulfate and sodium metabisulfite under a nitrogen atmosphere. The hydrogel was applied to the sensor by dip coating during polymerisation. Electrochemical measurements revealed that the response characteristics of sensors coated with this membrane are highly consistent. Scanning electrochemical microscopy (SECM) was used to spatially resolve glucose diffusion through the membrane by measuring the consequent H₂O₂ release and compared with an epoxy‐PU membrane. Hydrogen peroxide measurements using SECM revealed that the epoxy‐PU membranes had uneven lateral diffusion profiles compared to the uniform profile of the hydrogel membranes. The uneven diffusion profiles of epoxy‐PU membranes are attributed to a fabrication method that results in uneven membrane properties, while the uniform diffusion profiles of the hydrogel membranes are primarily dictated by their uniform pore size.     

Ending Aging in Super Glassy Polymer Membranes

Aging in super glassy polymers such as poly(trimethylsilylpropyne) (PTMSP), poly(4‐methyl‐2‐pentyne) (PMP), and polymers with intrinsic microporosity (PIM‐1) reduces gas permeabilities and limits their application as gas‐separation membranes. While super glassy polymers are initially very porous, and ultra‐permeable, they quickly pack into a denser phase becoming less porous and permeable. This age‐old problem has been solved by adding an ultraporous additive that maintains the low density, porous, initial stage of super glassy polymers through absorbing a portion of the polymer chains within its pores thereby holding the chains in their open position. This result is the first time that aging in super glassy polymers is inhibited whilst maintaining enhanced CO₂ permeability for one year and improving CO₂/N₂ selectivity. This approach could allow super glassy polymers to be revisited for commercial application in gas separations.     

An experimental and theoretical analysis of molecular separations by diffusion through ultrathin nanoporous membranes

Diffusion based separations are essential for laboratory and clinical dialysis processes. New molecularly thin nanoporous membranes may improve the rate and quality of separations achievable by these processes. In this work we have performed protein and small molecule separations with 15 nm thick porous nanocrystalline silicon (pnc-Si) membranes and compared the results to 1- and 3- dimensional models of diffusion through ultrathin membranes. The models predict the amount of resistance contributed by the membrane by using pore characteristics obtained by direct inspection of pnc-Si membranes in transmission electron micrographs. The theoretical results indicate that molecularly thin membranes are expected to enable higher resolution separations at times before equilibrium compared to thicker membranes with the same pore diameters and porosities. We also explored the impact of experimental parameters such as porosity, pore distribution, diffusion time, and chamber size on the sieving characteristics. Experimental results are found to be in good agreement with the theory, and ultrathin membranes are shown to impart little overall resistance to the diffusion of molecules smaller than the physical pore size cutoff. The largest molecules tested experience more hindrance than expected from simulations indicating that factors not incorporated in the models, such as molecule shape, electrostatic repulsion, and adsorption to pore walls, are likely important.     

Solution and Diffusion Behavior of Pure Gases and Gas Mixtures in Glassy Polymer Membranes

A general model for the solution and diffusion behavior in pure gas-polymer membrane systems and gas mixture-polymer membrane systems has been developed. Proved by experiments on different glassy and rubbery polymer membranes at various temperatures and pressures, this model can achieve the prediction of permeation behavior of pure gases and gas mixtures in polymer membranes only using the model parameters obtained from experiments on pure gases. The calculated results are in good agreement with experimental.     

A novel silk/PES hybrid nanofibrous scaffold promotes the in vitro proliferation and differentiation of adipose‐derived mesenchymal stem cells into insulin producing cells

Using stem cells to replace the lost beta cells is a hopeful strategy in the treatment of diabetic patients. Furthermore, during stem cell culture and therapy, it is a need to use a substrate to act as a supportive matrix to mimic 3D in vivo microenvironment. Therefore, in this study, human adipose‐derived stem cells were used to differentiate into insulin‐producing cells (IPCs) on a silk/polyethersulfone (PES) scaffold. After exposing to the differentiation media, 2D and 3D (silk/PES) cultured cells were gradually aggregated and formed spherical shaped clusters. The viability of cells was comparable in both 3D and 2D culture. As the results of gene expression assay in both RNA and protein level showed, the differentiation efficiency was higher in 3D culture. Furthermore, ELISA revealed that the release of C‐peptide and insulin was higher in 3D than 2D culture. It seems that silk/PES nanofibrous hybrid scaffold could provide an appropriate matrix to mimic in vivo microenvironment and therefore increases the IPC differentiation potency of stem cells.     

Adhesion of high polymers. I. Influence of diffusion,adsorption, and physical state on polymer adhesion

It is possible to identify three distinct types of polymer adhesion on the basis of the physical state of adhesive and adherend: (1) rubbery polymer–rubbery polymer (R–R adhesion); (2) rubbery polymer–glassy polymer (R–G adhesion); (3) rubbery polymer–nonpolymer (R–S adhesion). Limitations of the diffusion and adsorption theories and their conflicting results are discussed within the framework of the proposed classification. By defining the physical state of the polymer as an adhesive or as an adherend, it is possible to eliminate many of the discrepancies commonly noted in attempted application of the diffusion and adsorption theories. As predicted by the Bueche-Cashin-Debye equation, the diffusion of a polymer into another should be greatly reduced as it changes from the rubbery to the glassy state. For this reason, diffusion, which depends to a great extent on the physical state of the polymer, is actually a limited, selective process. Assuming a 10¹³ poise bulk viscosity at glass temperature, self-diffusion constants of forty polymers were calculated to be 10^?21cm.²/sec. or 10^?5A.²/sec. This slow rate of diffusion is unmeasurable and insignificant. Adsorption, which is less dependent on the physical state of the polymer, is more frequently encountered.     

Highly Stable,Low Gas Crossover,Proton‐Conducting Phenylated Polyphenylenes

Two classes of novel sulfonated phenylated polyphenylene ionomers are investigated as polyaromatic‐based proton exchange membranes. Both types of ionomer possess high ion exchange capacities yet are insoluble in water at elevated temperatures. They exhibit high proton conductivity under both fully hydrated conditions and reduced relative humidity, and are markedly resilient to free radical attack. Fuel cells constructed with membrane‐electrode assemblies containing each ionomer membrane yield high in situ proton conductivity and peak power densities that are greater than obtained using Nafion reference membranes. In situ chemical stability accelerated stress tests reveal that this class of the polyaromatic membranes allow significantly lower gas crossover and lower rates of degradation than Nafion benchmark systems. These results point to a promising future for molecularly designed sulfonated phenylated polyphenylenes as proton‐conducting media in electrochemical technologies.     

Calibration and Limits of Camera‐Based Fluorescence Correlation Spectroscopy: A Supported Lipid Bilayer Study

Camera‐based fluorescence correlation spectroscopy (FCS) approaches allow the measurement of thousands of contiguous points yielding excellent statistics and details of sample structure. Imaging total internal reflection FCS (ITIR‐FCS) provides these measurements on lipid membranes. Herein, we determine the influence of the point spread function (PSF) of the optical system, the laser power used, and the time resolution of the camera on the accuracy of diffusion coefficient and concentration measurements. We demonstrate that the PSF can be accurately determined by ITIR‐FCS and that the laser power and time resolution can be varied over a wide range with limited influence on the measurement of the diffusion coefficient whereas the concentration measurements are sensitive to changes in the measurement parameters. One advantage of ITIR‐FCS is that the measurement of the PSF has to be performed only once for a given optical setup, in contrast to confocal FCS in which calibrations have to be performed at least once per measurement day. Using optimized experimental conditions we provide diffusion coefficients for over ten different lipid membranes consisting of one, two and three constituents, measured in over 200000 individual correlation functions. Using software binning and thus the inherent advantage of ITIR‐FCS of providing multiple observation areas in a single measurement we test the FCS diffusion law and show how they can be complemented by the local information provided by the difference in cross‐correlation functions (ΔCCF). With the determination of the PSF by ITIR‐FCS and the optimization of measurement conditions ITIR‐FCS becomes a calibration‐free method. This allows us to provide measurements of absolute diffusion coefficients for bilayers with different compositions, which were stable over many different bilayer preparations over a time of at least one year, using a single PSF calibration.     

Reduction of a simple ion at permeable film-coated stationary electrodes

Recently proposed chemically prepared electrodes are coated with a thin, permeable, insulating, inert film which does not react with the depolarizer, does not allow depolarization on its surface and does not change the standard constant of the depolarization rate. It only changes the diffusion coefficient of a certain ion near the surface of the electrode. In this article, the theory of a reversible reduction of a simple ion at a film-coated stationary planar electrode is developed. If the film thickness is comparable with a diffusion layer thickness, considerable changes on the i-t curves can occur, but the position of the half-wave potential will remain constant.     

Novel tricontinuous hydrophilic–lipophilic–oxyphilic membranes: Synthesis and characterization

Novel tricontinuous membranes consisting of well‐defined hydrophilic poly(ethylene glycol) (PEG) and lipophilic polyisobutylene (PIB) segments crosslinked by oxyphilic poly(pentamethylcyclopentasiloxane) (PD₅) domains have been synthesized and characterized. Tricontinuity arises because the three membrane constituents—PEG, PIB, and PD₅—are mutually incompatible and give rise to three independent cocontinuous phases (channels). The continuous PEG segments impart swelling in water (hydrogel character), the rubbery PIB moieties provide strength, and the PD₅ domains provide crosslinking and enhanced O₂ permeability. The synthesis involves the random cohydrosilation of various lengths (number‐average molecular weights) of α,ω‐diallyl‐PEG and α,ω‐diallyl‐PIB segments by pentamethylcyclopentasiloxane (D₅H) followed by water‐mediated oxidation of the SiH groups of the D₅H to SiOH groups, which immediately polycondense to PD₅ domains. Membranes containing about equal amounts of PEG, PIB, and PD₅ give rise to tricontinuous morphologies that allow the simultaneous permeation of water, heptane, and oxygen via three cocontinuous channels. The number‐average molecular weight of the PEG segment, that is, the number‐average molecular weight of the hydrophilic segment between two PD₅ crosslink sites, determines the dimensions (pore sizes) of the channels through which water can permeate. A method has been developed for studying the oxygen permeability of membranes. The microarchitecture of the membranes has been investigated with selective swelling experiments and Fourier transform infrared spectroscopy, their mechanical properties have been examined in the water‐swollen state with Instron measurements, and their bulk morphologies and thermal degradation have been determined with differential scanning calorimetry and thermogravimetric analysis, respectively. The findings have been interpreted in terms of phase‐separated PEG, PIB, and PD₅ microdomains. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1209–1217, 2002     

Nanomechanical properties in ultrathin polymer films: Measurement on rectangular versus circular bubbles

Prior studies of inflation of circular membranes of ultrathin polystyrene (PS) films have evidenced a reduced glass transition temperature (T_g) and rubbery stiffening, whose origins remain unclear. Here, we describe results from inflation of rectangular, ultrathin films of the same PS material. The bubble shapes obtained from the experiment are consistent with finite element (FE) simulations. The accuracy of three approximate solutions for modulus obtained from the inflation of the thin, rectangular films was evaluated by comparison with FE analysis. The best among the three solutions was used to determine the creep compliance and rubbery stiffness of the thin films. It is found that the reduction of T_g and the rubbery stiffening for rectangular bubbles are consistent with results obtained using circular bubbles, although there is some indication that the rectangular bubbles give somewhat greater rubbery stiffening. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

pH‐induced on–off switching of polycarbonate track‐etched membranes by plasma‐induced surface grafting

Surface functionalization of the plasma‐pretreated polycarbonate (PC) track‐etched membranes via plasma‐induced thermally graft copolymerization of acrylic acid (AAc) was carried out. The resulting PC membranes with grafted AAc side chains were characterized by X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) spectroscopy, and thermogravimetric (TG) analysis. The morphology of the PC membranes was studied by scanning electron microscopy (SEM). The results showed that the grafted PAAc polymers were formed uniformly inside the pores throughout the entire membrane thickness. With increase in the pore‐filling ratio, the pore diameters of PAAc‐grafted membranes became smaller. The PC‐g‐PAAc membranes exhibit rapid and reversible response of the flux to the environmental pH as pH is switched between 3 and 9. Between pH 3.5 and 5.5, the membranes demonstrate a pH‐valve function as the carboxyl group changes from neutral to charged with a corresponding variation in chain configuration. Copyright © 2009 John Wiley & Sons, Ltd.     

Experimental analysis, modeling, and theoretical design of McMaster pore-filled nanofiltration membranes

A side-by-side comparison of the performance of McMaster pore-filled (MacPF) and commercial nanofiltration (NF) membranes is presented here. The single-salt and multi-component performance of these membranes is studied using experimental data and using a mathematical model. The pseudo two-dimensional model is based on the extended Nernst–Planck equation, a modified Poisson–Boltzmann equation, and hydrodynamic calculations. The model includes four structural properties of the membrane: pore radius, pure water permeability, surface charge density and the ratio of effective membrane thickness to water content. The analysis demonstrates that the rejection and transport mechanisms are the same in the commercial and MacPF membranes with different contributions from each type of mechanism (convection, diffusion and electromigration). Solute rejection in NF membranes is determined primarily by a combination of steric and electrostatic effects. The selectivity of MacPF membranes is primarily determined by electrostatic effects with a significantly smaller contribution of steric effects compared to commercial membranes. Hence, these membranes have the ability to reject ions while remaining highly permeable to low molecular weight organics. Additionally, a new theoretical membrane design approach is presented. This design procedure potentially offers the optimization of NF membrane performance by tailoring the membrane structure and operating variables to the specific process, simultaneously. The procedure is validated at the laboratory scale.     

Dimensional and concentration dependences of diffusion of aqueous alkaline-earth metal nitrate solutions in porous-glass membranes

Diffusion coefficients characterizing penetration of aqueous solutions of magnesium, calcium, strontium, and barium nitrates across porous-glass membranes with predominant pore radii of 4.5–70 nm were determined. A decrease in the pore radii of the membranes is accompanied in all cases by an exponential fall of the diffusion mobility. A reversal of the diffusion mobility series was observed for membranes with pore radii of 4.5 and 70 nm on the background of the general tendency toward a concentration-related rise in the diffusion coefficients.     

Spray-coated and solution-cast ethylcellulose pseudolatex membranes

Membranes of dibutyl sebacate (DBS) plasticized ethylcellulose pseudolatex were prepared by spray-coating and solution-casting methods for the studies of their transport and mechanical properties. The structure of sprayed membranes was more porous than that of cast membranes, so the sprayed membranes were more permeable than the cast membranes. The permeabilities of drug or water vapor through sprayed membranes decreased with increasing plasticizer concentration; on the contrary, those through cast membranes increased with increasing plasticizer concentration. The diffusion through pores accounts for the transport through sprayed membranes, while the solution–diffusion through plasticized polymer phase may become an important role for that through the cast membranes. Mechanically, the sprayed membranes were harder and more brittle than the cast membranes of similar formulation, but membranes prepared from both methods possessed similar breaking tensile strength. The tensile strength and Young's modulus were reduced and the elongation was improved with increasing plasticizer concentration for both kinds of membranes. The sprayed membranes would become less permeable and tougher after the post thermal treatment as the degree of coalescence between the latex particles in the membranes was enhanced.     

Pore‐filling electrolyte membranes based on microporous polyethylene matrices activated with plasma and sulfonated hydrogenated styrene butadiene block copolymer. Synthesis,microstructural and electrical characterization

In this research a series of pore‐filling electrolyte membranes were prepared, based on a sulfonated and hydrogenated styrene/butadiene block copolymer (SHSBS) and plasma‐treated microporous polyethylene (PE) membranes. The pore‐filling electrolyte membranes were characterized by means of scanning electronic microscopy (SEM), infrared spectroscopy (FTIR‐ATR), and dynamic mechanical analysis (DMA). In addition, the water uptake and methanol/water uptake capacities of these membranes were determined using several methanol in water solutions, as well as the permeability coefficients, for both water and methanol, using a 2 M methanol in water solution and pure methanol. Finally, electrical behavior was recorded by means of electrochemical impedance spectroscopy (EIS) and the four probe technique (FPT). The SEM images recorded show good coating of the pore‐filling electrolyte membranes on the plasma‐treated PE matrices, and DMA shows the proper relaxations of the two components: PE and SHSBS. Furthermore, the methanol/water absorption capacity was observed to diminish with plasma treatment of the matrix. Methanol permeability of the pore‐filling electrolyte membranes is notably lower than that of the Nafion® membrane, ion conductivity moving in the order of 10⁻² S cm⁻¹. Both of these characteristics qualify the experimental membranes as candidates to be applied as proton exchangers in fuel cells (FCs). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1684–1695, 2008