Ultra-thin film growth of titanium dioxide on W(1 0 0)

We have employed low energy electron diffraction (LEED) and X-ray photoelectron spectroscopy to follow the epitaxial growth of thin films of TiO₂ on W(1 0 0). The films were grown both by metal vapour deposition of titanium onto the substrate in UHV with subsequent annealing in a low partial pressure of oxygen, and by metal vapour deposition in a low partial pressure of oxygen. LEED patterns showed the characteristic patterns of (1 1 0) oriented rutile. A systematic spot splitting was observed and attributed to a stepped surface. The calculated step height was found to be in good agreement with that expected for rutile TiO₂(1 1 0), 3.3 Å. Titanium core level shifts were used to identify oxidation states as a function of film thickness allowing the interpretation in terms of a slightly sub-stoichiometric interface layer in contact with the substrate. In combination with the LEED patterns, the film structure is therefore determined to be (1 1 0) oriented rutile with a comparable level of stoichiometry to UHV prepared bulk crystals. The ordered step structure indicates considerable structural complexity of the surface.     

The magnetic map of NiMn alloy thin films on Co(0 0 1) and Co(1 1 1)

Following the experimental work of Groudeva-Zotova et al. [S. Groudeva-Zotova, D. Elefant, R. Kaltofen, D. Tietjen, J. Thomas, V. Hoffmann, C.M. Schneider, J. Magn. Magn. Mater. 263 (2003) 57] where the magnetic and structural characteristics of a bi-layer NiMn-Co exchange biasing systems was investigated, density functional calculations with generalized gradient corrections were performed on (Mn_0.5Ni_0.5)_n ordered alloy on Co(0 0 1) and one Mn_1−xNi_x monolayer on Co(1 1 1). For the Mn_0.5Ni_0.5 monolayer on Co(0 0 1), magnetic moments per surface atom of 0.65 μ_B and 3.76 μ_B were obtained for Ni and Mn, respectively. Those magnetic moments are aligned parallel to the total moment of Co(0 0 1). A complex behavior of the Mn moment in dependence of the thickness “n” is obtained for (Mn_0.5Ni_0.5)_n on Co(0 0 1). Investigations on Mn_1−xNi_x monolayer on Co(1 1 1) have shown that the crystallographic orientation does not modify significantly neither the magnetic moments of Mn and Ni atoms nor their ferromagnetic coupling with the Co(1 1 1) substrate, except for x = 0.66. For x = 0.66 the Mn sub-lattice presents an antiferromagnetic coupling leading to a quenching of the Ni magnetic moment.     

The epitaxial sexiphenyl (0 0 1) monolayer on TiO2(1 1 0): A grazing incidence X-ray diffraction study

A para-sexiphenyl monolayer of near up-right standing molecules (nominal thickness of 30 Å) is investigated in-situ by X-ray diffraction using synchrotron radiation and ex-situ by atomic force microscopy. A terrace like morphology is observed, the step height between the terraces is approximately one molecular length. The monolayer terraces, larger than 20 μm in size, are extended along the [0 0 1] direction of the TiO₂(1 1 0) substrate i.e. along the Ti-O rows of the reconstructed substrate surface. The structure of the monolayer and its epitaxial relationship to the substrate is determined by grazing incidence X-ray diffraction. Extremely sharp diffraction peaks reveal high crystalline order within the monolayer, which was found to have the bulk structure of sexiphenyl. The monolayer terraces are epitaxially oriented with the (0 0 1) plane parallel to the substrate surface (out-of-plane order). Four epitaxial relationships are observed. This in-plane alignment is determined by the arrangement of the terminal phenyl rings of the sexiphenyl molecules parallel to the oxygen rows of the substrate.     

Solid-state synthesis and magnetic properties of epitaxial FePd3(0 0 1) films

The solid-state synthesis of magnetically soft phase FePd₃ in epitaxial Pd(0 0 1)/Fe(0 0 1)/MgO(0 0 1) film systems was studied experimentally. The system had a Fe to Pd ratio of 1:3. An increase to 450 °C leads to the formation of three variants of ordered L1₀-FePd crystallites. At 500 °C, the solid-state reaction of unreacted Pd with L1₀-FePd crystallites initiates the growth of an ordered epitaxial L1₂-FePd₃(0 0 1) layer. When annealing at 650 °С, a gradual disordering is observed. The magnetic anisotropy (K₁=−2.0×10³ erg/cm³) and the saturation magnetization (M_S=650 emu/cm³) of the disordered FePd₃ phase were determined.     

FeO(1 1 1) formation by exposure of Fe(1 1 0) to atomic and molecular oxygen

The growth, structure, and morphology of ultrathin iron oxide layers formed on a Fe(1 1 0) single crystal surface are investigated by Auger electron spectroscopy, low energy electron diffraction, and grazing ion scattering. For Fe oxidation by atomic instead of molecular oxygen, the gas exposure can be reduced by almost two orders of magnitude because surface sticking and dissociation are not limiting the growth process. A well-ordered FeO(1 1 1) film with low defect density is only obtained with atomic oxygen. Compared to the bulk, the FeO lattice is laterally compressed by about 5-6% resulting in an in-plane oxygen (Fe) nearest-neighbor distance of 2.87 Å. Independent of the preparation method, long-range structural order is poor if the oxide film thickness is increased to 3-5 layers. This is attributed to the relatively large lattice mismatch between FeO(1 1 1) and Fe(1 1 0).     

Growth of thin Fe(0 0 1) films for terahertz emission experiments

The electrical and magnetic properties of thin iron (Fe) films have sparked significant scientific interest. Our interest, however, is in the fundamental interactions between light and matter. We have discovered a novel application for thin Fe films. These films are sources of terahertz (THz) radiation when stimulated by an incident laser pulse. After intense femtosecond pulse excitation by a Ti:sapphire laser, these films emit picosecond, broadband THz frequencies. The terahertz emission provides a direct measure of the induced ultrafast change in magnetization within the Fe film. The THz generation experiments and the growth of appropriate thin Fe films for these experiments are discussed. Several criteria are used to select the substrate and film growth conditions, including that the substrate must permit the epitaxial growth of a continuous, monocrystalline or single crystal film, yet must also be transparent to the emitted THz radiation. An Fe(0 0 1) film grown on the (0 0 1) surface of a magnesium oxide (MgO) substrate makes an ideal sample. The Fe films are grown by physical vapor deposition (PVD) in an ultrahigh vacuum (UHV) system. Low energy electron diffraction (LEED) and Auger electron spectroscopy (AES) are used to characterize the Fe(0 0 1) films. Two substrate surface preparation methods are investigated. Fe(0 0 1) films grown on MgO(0 0 1) substrates that are used as-received and films grown on MgO(0 0 1) substrates that have been UV/ozone-cleaned ex vacuo and annealed in vacuo produce the same results in the THz generation experiments. Either substrate preparation method permits the growth of samples suitable for the THz emission experiments.     

Structure and stability of Sb/Au(1 1 0)-c(2 × 2) surface phase

Adsorption of 0.5 monolayers (ML) of Sb on the Au(1 1 0) surface resulted in the formation of a c(2 × 2) surface reconstruction. Analysis of surface X-ray diffraction data by a direct method revealed the existence of an ordered substitutional surface alloy, with every other hollow site occupied by Au and Sb atoms. Quantitative conventional χ² refinement showed a contraction of 0.12 ± 0.03 Å in the spacing of the first Au layer to the second, an expansion of 0.13 ± 0.03 Å in the second-to-third layer distance, and an inward Sb displacement (rumpling) of 0.21 ± 0.04 Å. This surface phase proved to be extremely robust, with the long-range order of this arrangement remaining up to substrate temperatures of 900 K.     

X-ray multiple diffraction in the characterization of TiNO and TiO2 thin films grown on Si(0 0 1)

TiO₂ and TiN_xO_y thin films grown by low pressure metal-organic chemical vapor deposition (LP-MOCVD) on top of Si(0 0 1) substrate were characterized by X-ray multiple diffraction. X-ray reflectivity analysis of TiO₂[1 1 0] and TiNO[1 0 0] polycrystalline layers allowed to determine the growth rate (−80 Å/min) of TiO₂ and (−40 Å/min) of TiNO films. X-ray multiple diffraction through the Renninger scans, i.e., ?-scans for (0 0 2)Si substrate primary reflection is used as a non-conventional method to obtain the substrate lattice parameter distortion due to the thin film conventional deposition, from where the information on film strain type is obtained.     

Growth and oxidation of a Ni3Al alloy on Ni(1 0 0)

The growth and oxidation of a thin film of Ni₃Al grown on Ni(1 0 0) were studied using Auger electron spectroscopy (AES), low energy electron diffraction (LEED), and high resolution electron energy loss spectroscopy (EELS). At 300 K, a 12 Å thick layer of aluminium was deposited on a Ni(1 0 0) surface and subsequently annealed to 1150 K resulting in a thin film of Ni₃Al which grows with the (1 0 0) plane parallel to the (1 0 0) surface of the substrate. Oxidation at 300 K of Ni₃Al/Ni(1 0 0) until saturation leads to the growth of an aluminium oxide layer consisting of different alumina phases. By annealing up to 1000 K, a well ordered film of the Al₂O₃ film is formed which exhibits in the EEL spectra Fuchs-Kliewer phonons at 420, 640 and 880 cm⁻¹. The LEED pattern of the oxide shows a twelvefold ring structure. This LEED pattern is explained by two domains with hexagonal structure which are rotated by 90° with respect to each other. The lattice constant of the hexagonal structure amounts to ∼2.87 Å. The EELS data and the LEED pattern suggest that the γ^′-Al₂O₃ phase is formed which grows with the (1 1 1) plane parallel to the Ni(1 0 0) surface.     

Growth of Ce on Rh(1 1 1)

We have studied the growth of cerium films on Rh(1 1 1) using STM (scanning tunneling microscopy), LEED (low energy electron diffraction), XPS (X-ray photoelectron spectroscopy) and AES (Auger electron spectroscopy). Measurements of the Ce films after room temperature deposition showed that Ce is initially forming nanoclusters in the low coverage regime. These clusters consist of 12 Ce atoms and have the shape of pinwheels. At a coverage of 0.25 ML (monolayer, ML) an adatom layer with a (2 × 2) superstructure is observed. Above 0.4 ML, Rh is diffusing through pinholes into the film, forming an unstructured mixed layer. Annealing at 250 °C leads to the formation of ordered Ce-Rh compounds based on the bulk compound CeRh₃. At a coverage of 0.1 ML, small ordered (2 × 2) surface alloy domains are observed. The exchanged Rh atoms form additional alloy islands situated on the pure Rh(1 1 1) surface, showing the same (2 × 2) superstructure as the surface alloy. At a coverage of 0.25 ML, the surface is completely covered by the surface alloy and alloy islands. The (2 × 2) structure is equivalent to a (1 1 1)-plane of CeRh₃, contracted by 6%. Annealing a 1 ML thick Ce layer leads to a flat surface consisting of different rotational domains of CeRh₃(1 0 0). The Rh needed for alloy formation comes from 50 Å deep pits in the substrate. Finally we show that LEIS (low energy ion scattering) is not suitable for the characterization of Ce and CeRh films due to strong effects of neutralization.     

Atom geometry of nanostructured Fe films grown on c(2 × 2)-N/Cu(1 0 0) surface: An investigation by X-ray absorption spectroscopy with multishell analysis

We investigated the growth of Fe nanostructured films on c(2 × 2)-N/Cu(1 0 0) surface with Fe K-edge X-ray absorption fine structure (XAFS) in the near edge and in the extended energy region. The high photon flux of the incident X-rays allowed us to perform multishell analysis of the XAFS oscillations for Fe coverage Θ_Fe < 1 ML. This data analysis yields a detailed investigation of the atom geometry and some insights in the film morphology. At Θ_N < 0.5 ML (N saturation coverage) there is absence of contribution to XAFS from N atoms. First shell analysis of linearly polarized XAFS gives Fe-Fe (or Fe-Cu) bond length values varying between R₁ = 2.526 ± 0.006 Å at the highest Fe coverage (3 ML ) and R₁ = 2.58 ± 0.01 Å at Θ_Fe = 0.5 ML, Θ_N = 0.3 ML, with incidence angle Θ = 35°. These values are different from the case of bcc Fe (R = 2.48 Å), and compatible with fcc Fe (R₁ = 2.52 Å) and fcc Cu (R₁ = 2.55 Å). At the Fe lowest coverage (Θ_Fe = 0.5 ML) the dependence of R₁ on the incidence angle indicates expansion of the outmost layer. Near edge spectra and multishell analysis can be well reproduced by fcc geometry with high degree of static disorder. At N saturation pre-coverage (Θ_N = 0.5 ML) the XAFS analysis has to keep into account the Fe-N bonding. The results suggest two different adsorption sites: one with Fe in a fcc hollow site, surrounded by other metal atoms as nearest neighbours, and one resulting from an exchange with a Cu atom underneath the N layer.     

Nucleation of ordered Fe islands on Al2O3/Ni3Al(1 1 1)

Scanning tunneling microscopy (STM) has been used to investigate the nucleation and stability of iron clusters on the Al₂O₃/Ni₃Al(1 1 1) surface as a function of coverage and annealing temperature. We show that atomic beam deposition of iron leads to hexagonally ordered cluster arrangements with a distance of 24 Å between the clusters evidencing the template effect of the alumina film. The shape of the iron clusters is two-dimensional (2D) at deposition temperatures from 130 K to 160 K and three-dimensional (3D) at 300 K. However, the 2D iron clusters grown between 130 K and 160 K are stable up to 350 K.     

Low-frequency noise and inelastic tunneling spectroscopy in Fe(1 1 0)/MgO(1 1 1)/Fe(1 1 0) epitaxial magnetic tunnel junctions

We report on tunnelling magnetoresistance (TMR), current–voltage (IV) characteristics and low-frequency noise in epitaxially grown Fe(1 1 0)/MgO(1 1 1)/Fe(1 1 0) magnetic tunnel junctions (MTJs) with dimensions from 2×2 to 20×20 μm². The evaluated MgO energy barrier (0.50±0.08 eV), the barrier width (13.1±0.5 Å) as well as the resistance times area product (7±1 MΩ μm²) show relatively small variation, confirming a high quality epitaxy and uniformity of all MTJs studied. At low temperatures (T<10 K) inelastic electron tunneling spectroscopy (IETS) shows anomalies related to phonons (symmetric structures below 100 meV) and asymmetric features above 200 meV. We explain the asymmetric features in IETS as due to generation of electron standing waves in one of the Fe electrodes. The noise power, though exhibiting a large variation, was observed to be roughly anti-correlated with the TMR. Surprisingly, for the largest junctions we observed a strong enhancement of the normalized low-frequency noise in the antiparallel magnetic configuration. This behavior could be related to the influence of magnetostriction on the characteristics of the insulating barrier through changes in local barrier defects structure.     

STM investigations of Au(1 1 1) electrodes coated with vitamin B12 derivatives

Vitamin B₁₂ derivatives immobilized at flame-annealed Au(1 1 1) electrode surfaces have been investigated in close correlation with their structural properties and spatial arrangement at the electrode substrate by scanning tunneling microscopy (STM) in air and in aqueous 0.1 M NaClO₄ solution. The investigated compounds were symmetrical (B₁₂C₁₀S-SC₁₀B₁₂) and nonsymmetrical (B₁₂C₁₀S-SC₁₀) dialkyl disulfide derivatives of vitamin B₁₂, attached to the electrode surfaces by the S-Au bond. The ex situ and in situ STM experiments show the formation of a surface layer, whose packing density and structure is presumably controlled by the spatial arrangement of the large cobyrinate head groups. In presence of the symmetrical B₁₂ compound, a disordered surface layer is observed. Voltammetric investigations show that, in 0.1 M NaClO₄, this layer becomes unstable at potentials approximately ? −1000 mV vs. MSE and is almost completely removed at more negative potentials. The STM imaging properties of the nonsymmetrical B₁₂ surface layer show a significant dependence on the tunneling distance. In particular, at small tunneling distances, a highly regular hexagonal surface pattern is observed that suggests strongly the presence of an ordered surface assembly. Modeling of the B₁₂ head group has been performed to provide information for a structure-related interpretation of the high-resolution STM images. The investigations are first STM results obtained at such B₁₂ modified electrodes.     

Metastable magnetic configurations of (V, Cr, Mn and Fe) on Ir(0 0 1) surfaces

We present a theoretical study of the electronic and magnetic structure of the 3d-transition metals (M = V, Cr, Mn and Fe) in several overlayer systems. The electronic as well as magnetic structures are investigated for pseudomorphic overlayers (M/Ir(0 0 1)), ordered alloyed overlayers of the type M_0.5Ir_0.5/Ir(0 0 1) and ordered binary surface alloys of V, Cr, Mn and Fe transition metals on Ir(0 0 1) substrates. The calculations are performed with a self-consistent tight-binding method using the unrestricted Hartree-Fock approximation within the Hubbard model. We obtained metastable c(2 × 2) configurations for V, Cr and Mn and a p(1 × 1) configuration for Fe pseudomorphic overlayers. However, ferrimagnetic configuration has been obtained for the ordered surface alloys M_0.5Ir_0.5 and the binary alloyed overlayers on Ir(0 0 1) surfaces.     

Morphology of pentacene films deposited on Cu(1 1 9) vicinal surface

We investigate the morphology of a pentacene (C₂₂H₁₄) film adsorbed on the Cu(1 1 9) vicinal surface by scanning tunnelling microscopy (STM). Thermal treatment of a thick film of molecules generates a long-range ordered structure. Series of molecular rows are alternated with areas where the molecules assume two equivalent orientations. STM data analysis suggests that the ordered structure can be described by a rippled morphology. The behaviour of the film at different annealing temperatures suggests a possible explanation of the film structure as due to an adsorbate-induced modification of the substrate.     

First-principles study on the half-metallicity of zinc-blende CrP(1 1 0) surface

We have investigated the half-metallicity and magnetism at the (1 1 0) surface of CrP by using the all-electron full-potential linearized augmented plane wave (FLAPW) method within the generalized gradient approximation (GGA). From the calculated local density of states (LDOS), we found that the (1 1 0) surface of CrP preserves the half-metallicity, but the band gaps (∼1.1 eV) of the minority states for the surface Cr and P atoms are much reduced from the bulk value (∼1.9 eV). The magnetic moment of the P is coupled antiferromagnetically to that of the Cr. The magnetic moment of surface Cr atom is calculated to be 3.31μ_B which is increased by 10% compared to the bulk value, 3.00μ_B.     

The Fe/ZnO(0 0 0 1) interface: Formation and thermal stability

The room temperature growth mode and the interface reaction of Fe films on single crystalline ZnO(0 0 0 1) substrates prepared in ultra high vacuum (UHV) has been investigated by means of X-ray photoelectron and Auger electron spectroscopy (XPS, AES), low energy electron diffraction (LEED) and low energy ion scattering spectroscopy (LEIS). The results show that Fe grows in the pseudo layer-by-layer mode. At ambient temperature the deposited Fe film reduces the underlying ZnO single crystal resulting in FeO at the interface and metallic Zn, which partially diffuses into the remaining Fe overlayer. Annealing leads to a stepwise oxidation of the Fe to FeO (670 K) and Fe₂O₃ (820 K). The Fe₂O₃ mixes with the substrate resulting in two (1 1 1) oriented textures of a spinel phase found by electron backscatter diffraction analysis (EBSD). Fe-based spin-injection may play a vital role for ZnO-based spintronic devices.     

Sexithiophene films on ordered and disordered TiO2(1 1 0) surfaces: Electronic, structural and morphological properties

Growth of sexithiophene films on both ordered and disordered TiO₂(1 1 0) surfaces has been investigated by angle-resolved ultraviolet photoemission spectroscopy, atomic force microscopy, and X-ray diffraction including grazing-incidence characterization. The order (or disorder) of the TiO₂(1 1 0)-1 × 1 surface has been observed to profoundly influence the electronic, morphological, and structural properties of the 6T films: the band alignment, which determines the injection efficiency of contacts, has been considerably modified by 0.6 eV, and a morphology with either needle-like or dendritic-like islands has been obtained. The changes in the 6T film properties are associated with the orientational modifications of sexithiophene molecules within the films, either flat-lying or upright standing, 6T(0 1 0) or 6T(1 0 0) crystallites, respectively. The growth of different crystallite orientations is argued to be controlled by the kinetics mediated by the (dis)order of the TiO₂(1 1 0) surface rather than exclusively by chemical interaction between the molecule and the substrate.     

Epitaxial growth of Co(0 0 0 1)hcp/Fe(1 1 0)bcc magnetic bi-layer films on SrTiO3(1 1 1) substrates

Co(0 0 0 1)_hcp/Fe(1 1 0)_bcc epitaxial magnetic bi-layer films were successfully prepared on SrTiO₃(1 1 1) substrates. The crystallographic properties of Co/Fe epitaxial magnetic bi-layer films were investigated. Fe(1 1 0)_bcc soft magnetic layer grew epitaxially on SrTiO₃(1 1 1) substrate with two type variants, Nishiyama–Wasserman and Kurdjumov–Sachs relationships. An hcp-Co single-crystal layer is obtained on Ru(0 0 0 1)_hcp interlayer, while hcp-Co layer formed on Au(1 1 1)_fcc or Ag(1 1 1)_fcc interlayer is strained and may involve fcc-Co phase. It has been shown possible to prepare Co/Fe epitaxial magnetic bi-layer films which can be usable for patterned media application.