Synthesis and photovoltaic properties of 2,6‐bis(2‐thienyl) benzobisazole and 4,8‐bis(thienyl)‐benzo[1,2‐B:4,5‐B′]dithiophene copolymers

In an effort to design efficient low‐cost polymers for use in organic photovoltaic cells the easily prepared donor–acceptor–donor triad of a either cis‐benzobisoxazole, trans‐benzobisoxazole or trans‐benzobisthiazole flanked by two thiophene rings was combined with the electron‐rich 4,8‐bis(5‐(2‐ethylhexyl)‐thien‐2‐yl)‐benzo[1,2‐b:4,5‐b′]dithiophene. The electrochemical, optical, morphological, charge transport, and photovoltaic properties of the resulting terpolymers were investigated. Although the polymers differed in the arrangement and/or nature of the chalcogens, they all had similar highest occupied molecular orbital energy levels (?5.2 to ?5.3 eV) and optical band gaps (2.1–2.2 eV). However, the lowest unoccupied molecular orbital energy levels ranged from ?3.1 to ?3.5 eV. When the polymers were used as electron donors in bulk heterojunction photovoltaic devices with PC₇₁BM ([6,6]‐phenyl C₇₁‐butyric acid methyl ester) as the acceptor, the trans‐benzobisoxazole polymer had the best performance with a power conversion efficiency of 2.8%. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 316–324     

Synthesis,characterization, and solar cell and transistor applications of phenanthro[1,2‐b:8,7‐b′]dithiophene–Diketopyrrolopyrrole semiconducting polymers

Synthesis, characterization, and polymer solar cell and transistor application of a series of phenanthro[1,2‐b:8,7‐b′]dithiophene‐based donor–acceptor (D–A)‐type semiconducting polymers combined with a diketopyrrolopyrrole unit are reported. The present polymers showed some unique features such as strong aggregation behavior, high thermal stability, and short π–π stacking distance (3.5–3.6 Å), which are suitable for high performance organic materials. In addition, they have a significantly extended absorption up to 1000 nm with a band gap of ca. 1.2 eV. However, such strong intermolecular interaction reduced their solubility and molecular weights, which resulted in low crystalline nature and moderate field‐effect mobility of 0.01 cm² V^?1 s^?1. Furthermore, such strong aggregation behavior led to the large‐scale phase separation in the blend films, which may prevent the effective photocurrent generation, limiting J_sc and power conversion efficiency of 2.0%. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 709–718     

[1,2,5]thiadiazolo[3,4‐g]quinoxaline acceptor‐based donor–acceptor–donor‐type polymers: Effect of strength and size of donors on the band gap

Electrochromic polymers based on [1,2,5]thiadiazolo[3,4‐g]quinoxaline acceptor and thiophene, 3,4‐ethylenedioxythiophene and 3,3‐didecyl‐3,4‐proylenedioxythiophene donors, namely poly(6,7‐diphenyl‐4,9‐di(thiophen‐2‐yl)‐[1,2,5]thiadiazolo[3,4‐g]quinoxaline) ( P1 ), poly(4‐(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐5‐yl)‐9‐(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐7‐yl)‐6,7‐diphenyl‐[1,2,5]thiadiazolo[3,4‐g]quinoxaline) ( P2 ), and poly(4‐(3,3‐didecyl‐3,4‐dihydro‐2H‐thieno[3,4‐b][1,4]dioxepin‐6‐yl)‐9‐(3,3‐didecyl‐3,4‐dihydro‐2H‐thieno[3,4‐b][1,4]dioxepin‐8‐yl)‐6,7‐diphenyl‐[1,2,5]thiadiazolo[3,4‐g]quinoxaline) ( P3 ), respectively, were electrochemically and/or chemically synthesized and characterized. Electrochemical and optical properties of the polymers were then investigated. The results, which were obtained electrochemically and optically, indicate that the polymers bearing the same acceptor and different donor units have a band gap range of 0.59–1.24 eV depending on the strength and size of the donor units and band gap determination method. A significant finding in this study was the phenomenon that when the acceptor is physically huge, the general rule that a weak donor would have a high band gap whereas a strong donor would have low band gap can be broken due to the torsional angles/steric hindrances involved with physically large donor molecules. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3483–3493     

Synthesis and characterization of soluble polyimides derived from [1,1′;4′,1″]terphenyl‐2′,5′‐diol and biphenyl‐2,5‐diol

Two series of polyimides based on laterally attached p‐terphenyl and biphenyl groups were synthesized. The solubility and thermal properties were studied using DSC, thermogravimetric analysis, and the solubility test. These polymers exhibited good thermal stability and excellent solubility. The high solubility for both polymer series was attributed to the non‐coplanarity of diamine monomers and the use of fluorinated dianhydride, whereas the slightly better solubility for polymers based on p‐terphenyl was attributed to further weakening of interchain interaction of the polymers. Both polymer series exhibited glass‐transition temperatures (T_g's) in the range of 244–272 °C. The T_g's of polymers containing laterally attached p‐terphenyls were higher than those of their counterparts containing biphenyls by 5–17 °C. This was attributed to the formation of an interdigitated structure that hinders the segmental movement of polymer chains. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2998–3007, 2001     

Supramolecular assembly of H‐bonded side‐chain polymers containing conjugated pyridyl H‐acceptor pendants and various low‐band‐gap H‐donor dyes bearing cyanoacrylic acid groups for organic solar cell applications

Novel supramolecular side‐chain polymers were constructed by complexation of proton acceptor (H‐acceptor) polymers, i.e., side‐chain conjugated polymers P1–P2 containing pyridyl pendants, with low‐band‐gap proton donor (H‐donor) dyes S1–S4 (bearing terminal cyanoacrylic acids) in a proper molar ratio. Besides unique mesomorphic properties confirmed by DSC and XRD results, the H‐bonds of supramolecular side‐chain structures formed by pyridyl H‐acceptors and cyanoacrylic acid H‐donors were also confirmed by FTIR measurements. H‐donor dyes S1–S4 in solid films exhibited broad absorption peaks located in the range of 471–490 nm with optical band‐gaps of 1.99–2.14 eV. Furthermore, H‐bonded polymer complexes P1/S1–P1/S4 and P2/S1–P2/S4 exhibited broad absorption peaks in the range of 440–462 nm with optical band‐gaps of 2.11–2.25 eV. Under 100 mW/cm² of AM 1.5 white‐light illumination, the bulk heterojunction polymer solar cell (PSC) devices containing an active layer of H‐bonded polymer complexes P1/S1–P1/S4 and P2/S1–P2/S4 (as electron donors) mixed with [6,6]‐phenyl C₆₁ butyric acid methyl ester (i.e., PCBM, as an electron acceptor) in the weight ratio of 1:1 were investigated. The PSC device containing H‐bonded polymer complex P1/S3 mixed with PCBM (1:1 w/w) gave the best preliminary result with an overall power conversion efficiency (PCE) of 0.50%, a short‐circuit current of 3.17 mA/cm², an open‐circuit voltage of 0.47 V, and a fill factor of 34%. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5998–6013, 2009     

Pyrrolo[3,4‐c]pyrrole‐1,3‐dione‐based large band gap polymers containing benzodithiophene derivatives for highly efficient simple structured polymer solar cells

Pyrrolo[3,4‐c]pyrrole‐1,3(2H,5H)‐dione (DPPD)‐based large band gap polymers, P(BDT‐TDPPDT) and P(BDTT‐TDPPDT), are prepared by copolymerizing electron‐rich 4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene (BDT) or 4,8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene (BDTT) unit with novel electron deficient 2,5‐dioctyl‐4,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,3(2H,5H)‐dione (TDPPDT) unit. The absorption bands of polymers P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) cover the region from 300 to 600 nm with an optical band gap of 2.11 eV and 2.04 eV, respectively. The electrochemical study illustrates that the highest occupied/lowest unoccupied molecular orbital energy levels of P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) are ?5.39 eV/?3.28 eV and ?5.44 eV/?3.40 eV, respectively. The single layer polymer solar cell (PSC) fabricated with a device structure of ITO/PEDOT:PSS/P(BDT‐TDPPDT) or P(BDTT‐TDPPDT):PC70BM+DIO/Al offers a maximum power conversion efficiency (PCE) of 6.74% and 6.57%, respectively. The high photovoltaic parameters such as fill factor (～72%), open circuit voltage (V_oc, ～0.90 V), incident photon to collected electron efficiency (～76%), and PCE obtained for the PSCs made from polymers P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) make them as promising large band gap polymeric candidates for PSC application. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3564–3574     

Design,synthesis, photophysical,and electrochemical properties of DCM‐based conjugated polymers for light‐emitting devices

A series of conjugated hyperbranched polymers, hyperbranched copolymers, and linear polymers containing 2‐pyran‐4‐ylidenemalononitrile (acceptor) and triphenylamine/fluorene (donor) units were synthesized and characterized by FTIR, ¹H NMR, thermogravimetric analyses, differential scanning calorimetry, gel permeation chromatography, UV–visible, photoluminescence, and cyclic voltammetry measurements. All the polymers show red‐light emission in the range of 566–656 nm both in solution and in solid state. The quantum efficiency of the polymers was in the range of 56–82%. Among the six polymers synthesized, only polymers containing fluorene units show T_g and polymers based on triphenylamine not exhibit T_g. The band gap of these polymers were found to be reasonably low; hyperbranched copolymer containing fluorene unit shows lowest band gap of 2.18 eV due to the stabilization of LUMO energy level by the electron withdrawing ? CN groups. The thermal and solubility behavior of the polymers were found to be good. All the EL spectra of the devices (indium‐tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/polymer/2,9‐dimethyl‐4,7‐diphenyl‐1,10‐phenanthroline/tris(8‐hydroxyquinoline)aluminum)/LiF/Al) show red‐light emission, and the device fabricated with P3 and P4 shows maximum luminance and luminous efficiency of 4104 cd m^?2 and 0.55 cd Å^?1 and 3696 cd m^?2 and 0.47 cd Å^?1, respectively, indicates that they had the best carrier balance. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Conjugated random terpolymers based on benzodithiophene,diketopyrrolopyrrole, and 8,10‐bis(thiophen‐2‐yl)‐2,5‐di(nonadecan‐3‐yl)bis[1,3]thiazolo[4,5‐f:5′,4′‐h]thieno[3,4‐b]quinoxaline for Efficient Polymer Solar Cell

A series of novel donor–acceptor (D–A) random conjugated terpolymers P2‐P4 along with the homopolymers P1 (BDT‐DPP) and P5 (BDT‐BTDQ) were designed and synthesized by copolymerizing a benzo[1,2‐b:4,5‐b]dithiophene (BDT) donor with an electron‐deficient diketopyrrolo[3,4‐c]pyrrole (DPP) unit and a benzothiadiazolo[3,4‐e]quinoxaline (BTDQ) moieties of different electron‐withdrawing strengths, and the resultant terpolymers showed broad absorption profile ranging from 300 to 1200 nm. The HOMO levels of the polymers were adjusted from ?5.23 to ?5.11 eV, and the optical bandgaps were controlled from 1.32 to 1.13 eV by changing the molar ratio of DPP and BTDQ acceptors. These terpolymers were used as a donor along with PC₇₁BM as an acceptor for the creation of polymer solar cells, and the performance was optimized via variable the donor to acceptor ratio and solvent vapor annealing. The polymer solar cells made from the random terpolymer P3 showed the highest overall power conversion efficiency of (9.27%), which is higher than that for the corresponding homo‐polymers counterparts, that is, P1 (7.27%) and P5 (7.68%). The results demonstrate that the designing of random D‐A1‐D‐A2 terpolymers may be the best approach for efficient polymer solar cells. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1478–1485     

New π‐Conjugated polymers containing 4H,4′H‐[1,1′‐Bithieno [3,4‐C]Pyrrole]‐4,4′,6,6′(5H,5′H)‐Tetraone (biTPD) units and their application to thin‐Film transistors and photovoltaic cells

We successfully synthesized new D‐A copolymers that employ 1,10‐bithienopyrrolodione (biTPD), thiophene, and selenophene‐based donor monomeric units. Two polymers, PBTPDEBT and PBTPDEBS , exhibited high degrees of crystallinity and unique polymer chain arrangements on the substrate, which is attributed to their enhanced coplanarity and intermolecular interactions between the polymer chains. Among the thin‐film transistor devices made of PBTPDEBT and PBTPDEBS , the annealed PBTPDEBS device displayed relatively high hole mobility, which was twice that of the PBTPDEBT ‐based device. In addition, an organic photovoltaic device based on a PBTPDEBS :PC₇₁BM blend displayed the maximum power conversion efficiency of 3.85%. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1228–1235     

Efficient π‐conjugated interrupted host polymer by metal‐free polymerization for blue/green phosphorescent light‐emitting diodes

A new aromatic host polymer poly{[1,4‐bis(9‐decylcarbazole‐3‐yl)‐2,3,5,6‐tetrafluorobenzene‐3,3′‐diyl]‐alt‐[N‐methylisatin‐2‐one‐3,3‐diyl]} (PICzFB) containing carbazole–tetrafluorinebeneze–carbazole moiety in the π‐conjugated interrupted polymer backbone was synthesized by superacid‐catalyzed metal‐free polyhydroxyalkylation. The resulted copolymer PICzFB showed a comparatively wide band gap up to 3.32 eV and high triplet energy (E_T) of 2.73 eV due to confined conjugation by the δ? C bond interrupted polymer backbone. Blue and green light‐emitting devices with PICzFB as host, FIrpic and Ir(mppy)₃ as phosphorescent dopants showed the maximum luminous efficiencies of 5.0 and 27.6 cd/A, respectively. The results suggested that the strategy of incorporating bipolar unit into the π‐conjugated interrupted polymer backbone can be a promising approach to obtain host polymer with high triplet level for solution‐processed blue and green phosphorescent polymer light‐emitting diodes. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1037–1046     

Synthesis and characterization of new low band‐gap polymers containing electron‐accepting acenaphtho[1,2‐c]thiophene‐S,S‐dioxide groups

Two donor–acceptor conjugated polymers, PTSSO‐TT and PTSSO‐BDT, composed of acenaphtho[1,2‐c]thiophene ‐ S,S‐dioxide (TSSO) as a new electron acceptor and thienothiophene (TT) or benzo[1,2‐b:4,5‐b']dithiophene (BDT) as electron donors, were synthesized with Stille cross‐coupling reactions. The number‐averaged molecular weights (M_n) of PTSSO‐TT and PTSSO‐BDT were found to be 15100 and 26000 Da, with dispersity of 1.8 and 2.4, respectively. The band‐gap energies of PTSSO‐TT and PTSSO‐BDT are 1.56 and 1.59 eV, respectively. The HOMO levels of PTSSO‐TT and PTSSO‐BDT are ?5.4 and ?5.5 eV, respectively. These results indicate that the inclusion of TSSO accepting units into polymers is a very effective method for lowering their HOMO energy levels. The field‐effect mobilities of PTSSO‐TT and PTSSO‐BDT were determined to be 1.5 × 10^?3 and 4.5 × 10^?4 cm² V^?1 s^?1, respectively. A polymer solar cell device prepared with PTSSO‐TT as the active layer was found to exhibit a power conversion efficiency (PCE) of 3.79% with an open circuit voltage of 0.71 V under AM 1.5 G (100 mW cm^?2) conditions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 498–506     

Design and synthesis of dithieno[3,2‐b:2′3′‐d]pyrrole‐based conjugated polymers for photovoltaic applications: consensus between low bandgap and low HOMO energy level

A strategy of the fine‐tuning of the degree of intrachain charge transfer and aromaticity of polymer backbone was adopted to design and synthesize new polymers applicable in photovoltaics. Three conjugated polymers P1 , P2 , and P3 were synthesized by alternating the electron‐donating dithieno[3,2‐b:2′3′‐d]pyrrole (D) and three different electron‐accepting (A) segments ( P1 : N‐(2‐ethylhexyl)phthalimide; P2 : 1,4‐diketo‐3,6‐diphenylpyrrolo[3,4‐c]pyrrole; and P3 : thiophene‐3‐hexyl formate) in the polymer main chain. Among the three polymers, P2 possessed the broadest absorption band ranging from 300 to 760 nm, the lowest bandgap (1.63 eV), and enough low HOMO energy level (?5.27 eV) because of the strong intrachain charge transfer from D to A units and the appropriate extent of quinoid state in the main chain of P2 , which was convinced by the theoretical simulation of molecular geometry and front orbits. Photovoltaic study of solar cells based on the blends of P1 – P3 and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) demonstrated that P2 :PCBM exhibited the best performance: a power conversion efficiency of 1.22% with a high open‐circuit voltage (V_OC) of 0.70 V and a large short‐circuit current (I_SC) of 5.02 mA/cm² were achieved. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

4H‐cyclopenta[2,1‐b:3,4‐b′]dithiophen‐4‐one (CPDTO) homopolymer with side chains on every other CPDTO

A soluble 4H‐cyclopenta[2,1‐b ;3,4‐b ′]dithiophene‐4‐one (CPDTO)‐based polymer (C₆‐PCPDTO) has been synthesized from two monomers derived from nonalkylated CPDTO and didodecyl CPDTO (C₁₂‐CPDTO). Proton NMR, thermal analysis, UV–vis absorption, cyclic voltammetry, and XRD are used to characterize the polymer in solution and film. The new polymer has an optical bandgap of 1.28 eV in film, and has strong interchain interaction in chloroform solutions. The polymer contains a significant amount of homocoupled segments. The regular segments and homocoupled CPDTO segments render the polymer highly aggregating in solution. The non‐planar homocoupled C₁₂‐CPDTO segments prevent the polymer from forming regular π‐stacks, resulting in a low SCLC hole mobility (3.88 × 10^?7 cm²V^?1s^?1). CV experiments show that C₆‐PCPDTO is stable in its oxidized and reduced states. Solar cell devices were fabricated from C₆‐PCPDTO2 :PC₆₀BM blends of different weight ratios. High PC₆₀BM loading (80% or greater) was required for the devices to show measurable efficiency, indicating that the limited π‐stacking of the polymer is not sufficient to cause effective phase separation. Further development of synthetic method is still needed to eliminate structural defects so that long‐range ordered pi‐stacking can be realized in the polymer for these applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1077–1085     

Synthesis and characterization of color‐stable electroluminescent polymers: Poly(dinaphtho[1,2‐a:1′,2′‐g]‐s‐indacene)s

Two new stepladder conjugated polymers, that is, poly(7,7,15,15‐tetraoctyldinaphtho[1,2‐a:1′,2′‐g]‐s‐indacene) (PONSI) and poly(7,7,15,15‐tetra(4‐octylphenyl)dinaphtho[1,2‐a:1′,2′‐g]‐s‐indacene) (PANSI) with alkyl and aryl substituents, respectively, have been synthesized and characterized. In comparison with poly(indenofluorene)s, both polymers have extended conjugation at the direction perpendicular to the polymer backbone because of the introduction of naphthalene moieties. The emission color of the polymers in film state is strongly dependent on the substituents. While PONSI emits at a maximum of 463 nm, PANSI with the same backbone but aryl substituents displays dramatically redshifted emission with a maximum at 494 nm. Both polymers show stable photoluminescence spectra while annealing at 200 °C in inert atmosphere. The PONSI‐based devices with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al turn on at 3.7 V, and emit at a maximum of 461 nm with the CIE coordinates of (0.19, 0.26), a maximum luminance efficiency of 1.40 cd/A, and a maximum brightness of 2036 cd/m² at 13 V. Meanwhile, the emission color of the devices is independent of driving voltage and keeps unchanged during the continuous operation. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4866–4878, 2008     

Synthesis and characterization of novel polyamide‐imides containing noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit

A new diimide‐dicarboxylic acid, 2,2′‐dimethyl‐4,4′‐bis(4‐trimellitimidophenoxy)biphenyl (DBTPB), containing a noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit was synthesized by the condensation reaction of 2,2′‐dimethyl‐4,4′‐bis(4‐minophenoxy)biphenyl (DBAPB) with trimellitic anhydride in glacial acetic acid. A series of new polyamide‐imides were prepared by direct polycondensation of DBAPB and various aromatic diamines in N‐methyl‐2‐pyrrolidinone (NMP), using triphenyl phosphite and pyridine as condensing agents. The polymers were produced with high yield and moderate to high inherent viscosities of 0.86–1.33 dL · g⁻¹. Wide‐angle X‐ray diffractograms revealed that the polymers were amorphous. Most of the polymers exhibited good solubility and could be readily dissolved in various solvents such as NMP, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide (DMF), dimethyl sulfoxide, pyridine, cyclohexanone, and tetrahydrofuran. These polyamide‐imides had glass‐transition temperatures between 224–302 °C and 10% weight loss temperatures in the range of 501–563 °C in nitrogen atmosphere. The tough polymer films, obtained by casting from DMAc solution, had a tensile strength range of 93–115 MPa and a tensile modulus range of 2.0–2.3 GPa. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 63–70, 2001     

Synthesis and characterization of new highly organosoluble poly(ether imide)s based on 3,3′,5,5′‐tetramethyl‐2,2‐bis[4‐(4‐dicarboxyphenoxy)phenyl]propane dianhydride

A new bis(ether anhydride), 3,3′,5,5′‐tetramethyl‐2,2‐bis[4‐(4‐dicarboxyphenoxy)phenyl]propane dianhydride ( 3 ), was prepared in three steps: the nitro displacement of 4‐nitrophthalonitrile with 2,2‐bis(4‐hydroxy‐3,5‐dimethylphenyl)propane, the alkaline hydrolysis of the intermediate bis(ether dinitrile), and the subsequent dehydration of the resulting bis(ether diacid). A series of new highly soluble poly(ether imide)s with tetramethyl and isopropylidene groups were prepared from the bis(ether anhydride) 3 with various diamines by a conventional two‐stage synthesis including polyaddition and chemical cyclodehydration. The resulting poly(ether imide)s had inherent viscosities of 0.54–0.73 dL g^?1. Gel permeation chromatography measurements revealed that the polymers had number‐average and weight‐average molecular weights of up to 54,000 and 124,000, respectively. All the polymers showed typical amorphous diffraction patterns. All of the poly(ether imide)s showed excellent solubility and were readily dissolved in various solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, pyridine, cyclohexanone, tetrahydrofuran, and even chloroform. Most of the polymers could be dissolved with chloroform concentrations as high as 30 wt %. These polymers had glass‐transition temperatures of 244–282 °C. Thermogravimetric analysis showed that all polymers were stable, with 10% weight losses recorded above 463 °C in nitrogen. These transparent, tough, and flexible polymer films were obtained through solution casting from N,N‐dimethylacetamide solutions. These polymer films had tensile strengths of 81–102 MPa and tensile moduli of 1.8–2.0 GPa. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2556–2563, 2002     

A wide band gap polymer derived from 3,6‐carbazole and tetraphenylsilane as host for green and blue phosphorescent complexes

We have synthesized a novel wide band gap polymer P36HCTPSi derived from 3,6‐carbazole and tetraphenylsilane by palladium‐catalyzed Suzuki coupling reaction. The resultant polymer shows a high glass transition temperature (217 °C) and good thermal stability. The conjugation length of P36HCTPSi is effectively confined because of the δ‐Si interrupted polymer backbone. The polymer exhibits a violet emission with a peak at 392 nm in solution, and the band gap estimated from the onset of its absorption is 3.26 eV. The high energy emission and wide band gap of P36HCTPSi make it appropriate host for green and blue emission phosphorescent materials. Efficient energy transfers from P36HCTPSi to both fac‐tris[2‐(2‐pyridyl‐kN)‐5‐methylphenyl]iridium(III) (green emission) and bis[(4,6‐difluorophenyl)pyridinato‐N,C²]‐(picolinato)iridium(III) (blue emission) were observed in photoluminescence (PL) spectra. Highly efficient phosphorescent polymer light‐emitting devices were realized by using P36HCTPSi as the host for iridium complexes, the maximum luminous efficiencies for green and blue devices were 27.6 and 3.4 cd/A, respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4784–4792, 2009     

Control of vertical distribution of thiophene‐based copolymers containing 4,7‐Dithien‐2‐yl‐benzo[C][1,2,5]thiadiazole and 3,6‐Dithien‐2‐yl‐pyrrolo[3,4‐C]pyrrole‐1,4(2H,5H)‐dione as Side Groups for Photovoltaics

Four new D—A type copolymers with 2D‐conjugated side‐chain identified PfToBT, PbToBT, PfTDPP and PbTDPP, containing two acceptors 4,7‐dithien‐2‐yl‐benzo[c][1,2,5]thiadiazole (DTBT), and diketopyrrolopyrrole (DPP) linked by thiophene donors, are obtained using Pd‐catalyzed Stille‐coupling reaction. These polymers show a broad visible‐near‐infrared absorption band (E_g = 1.79–1.66 eV) and possess a relatively low‐lying HOMO level at ?5.34 to ?5.12 eV. All the polymer:PC₇₀BM blend films showed edge‐on structure and have similar d_π‐spacing values. According to the structure of conjugated side‐chain, the vertical distributions of polymer chains and PC₇₀BM within the BHJ (bulk heterojunction) were different. When DPP used as an acceptor, conjugated side chains of the polymer coexisted with PC₇₀BM in same position. The BHJ film prepared from PfToBT, PbToBT had a discontinuous network between polymer and PC₇₀BM, whereas films from PfTDPP and PbTDPP formed continuous and evenly distributed network between them. This optimized vertical morphology promotes hole transport along respective pathways of polymers and fullerenes in the vertical direction, leading to high J_SC. PbTDPP shows PCE up to 2.9% (Jsc of 9.4 mA/cm², Voc of 0.68 V, and FF of 0.44). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2746–2759     

Synthesis and characterization of an ionic conjugated polymer: Poly[2‐ethynyl‐N‐(2‐thiophenecarbonyl) pyridinium chloride]

The activated polymerization of 2‐ethynylpyridine by using 2‐thiophenecarbonyl chloride yielded the corresponding conjugated ionic polymer, poly[2‐ethynyl‐N‐(2‐thiophenecarbonyl)pyridinium chloride] (PETCPC). The polymerization proceeded well to give high yield of polymer without any additional initiator or catalyst. The instrumental analysis data on polymer structure indicated that the present ionic polymer have a conjugated polymer backbone system having N‐(2‐thiophenecarbonyl)pyridinium chloride as substituents. The photoluminescence maximum peak of PETCPC was located at 573 nm, which corresponds to the photon energy of 2.16 eV. The aromatic functional substituents in the conjugated backbone system shift PL maximum values because it makes different molecule arrangement. The cyclovoltamograms of PETCPC exhibited the electrochemically stable window at ?1.24 to 1.80 V region. It was found that the kinetics of the redox process of polymer might be controlled by the reactant diffusion process from the experiment of the oxidation current density of polymer versus the scan rate. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6153–6162, 2009     

Synthesis and characterization of low‐band‐gap conjugated polymers containing phenothiazine and benzo‐2,1,3‐thia‐/seleno‐diazole

Two phenothiazine‐based conjugated polymers, poly(3, 7‐divinylene‐N‐octyl‐phenothiazine‐alt‐benzo‐2,1,3‐ thiadiazole) (PQS) and poly(3,7‐divinylene‐N‐octyl‐phenothiazine‐alt‐benzo‐2,1,3‐selenodiazole) (PQSe) were synthesized by Heck coupling reaction. The chemical structures of the two polymers were confirmed by ¹H‐NMR and Ft‐IR. They showed good solubility in some common organic solvents such as tetrahydrofuran (THF), chloroform. The weight‐average molecular weight (Mw) of the polymers determined by GPC in THF against polystyrene standards was 3.7 × 10³ for PQS and 1.9 × 10³ for PQSe, respectively. The temperatures of 5% weight loss (T₅) were 385.0°C for PQS and 324.0°C for PQSe, respectively, determined by TGA measurements under nitrogen ambience. UV–vis absorption spectra of the polymer films showed the absorption maxima at 537 nm for PQS and 539 nm for PQSe, with the full width at half maximum (FWHM) of 190 and 230 nm, respectively. The optical band gaps ( ) of the polymer films are 1.86 eV for PQS and 1.80 eV for PQSe, respectively. As the polymers have low‐band‐gap and broad absorption in the visible region, they may be used as potential light‐harvesting materials for photovoltaic devices (PVDs). Furthermore, photoluminescence (PL) spectra of the polymer solutions showed the emission maxima at 698 nm for PQS and 709 nm for PQSe, with FWHM of 152 nm and 167 nm, respectively, which revealed that these two polymers may be used as red and near infrared light‐emitting materials for polymeric light‐emitting diodes (PLEDs). Copyright © 2009 John Wiley & Sons, Ltd.