Synthesis and properties of organosoluble polynaphthalimides based on 1,4,5,8‐naphthalene tetracarboxylic dianhydride, 3,3‐bis[4‐(4‐aminophenoxy)phenyl]phthalide,and various aromatic diamines

Two series of polynaphthalimides (PNIs), II and III , were prepared from 1,4,5,8‐naphthalene tetracarboxylic dianhydride with the usual aromatic diamines ( Ia – Ih ) or Ia , which was used as a soluble modifying agent, and Ib – Ih via a one‐stage process with high‐temperature condensation. Series II and III had inherent viscosities of 0.57–1.34 and 1.15–1.63 dL/g, respectively. IIa and most of the III series were soluble in 1‐methy‐2‐pyrrolidone and m‐cresol at 5–10 wt % and afforded transparent and tough films by m‐cresol solvent casting with a tensile strength in the range of 75–99 MPa. The glass‐transition temperature and softening temperature of these PNIs were in the ranges of 360–404 and 188–241 °C, respectively, and the 10% weight loss temperatures were above 495 °C, with more than a 44% char yield at 800 °C in nitrogen. These PNI films had dielectric constants of 4.14–6.46 (1 MHz), with moisture absorption in the range of 0.87–1.91 wt %. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 940–948, 2006     

Composite of P(VDF‐CTFE) and aromatic polythiourea for capacitors with high‐capacity,high‐efficiency,and fast response

For next generation of miniaturized personal electronics and pulsed power systems for smart power grids, electric vehicles, and electromagnetic launchers, flexible capacitors from dielectric polymers with high‐capacity, high‐efficiency, and fast response are highly desirable. Dielectric polymer composite of P(VDF‐CTFE), that is poly(vinylidene fluoride‐chlorotrifluoroethylene) and a small amount of aromatic polythiourea (PTU) has been described. It combines the merits of both polymers, that is high dipole density and easy processability of P(VDF‐CTFE), as well as large dipole moment and high charge–discharge efficiency of PTU. Most impressively, PTU boosts the maximum breakdown strength of P(VDF‐CTFE), and thus extracts its maximum energy reserve capacity. PTU also contributes to the promoted charge–discharge efficiency, accelerated discharge, and reduced dielectric loss in P(VDF‐CTFE), which facilitate the composite for flexible capacitor applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 193–199     

Novel organosoluble and colorless poly(ether imide)s based on 3,3‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]phthalide dianhydride and aromatic bis(ether amine)s bearing pendent trifluoromethyl groups

A novel series of colorless and highly organosoluble poly(ether imide)s were prepared from 3,3‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]phthalide dianhydride with various fluorinated aromatic bis(ether amine)s via a conventional two‐stage process that included ring‐opening polyaddition to form the poly(amic acid)s followed by cyclodehydration to produce the polymer films. The poly(ether imide)s showed excellent solubility, with most of them dissoluble at a concentration of 10 wt % in amide polar solvents, in ether‐type solvents, and even in chlorinated solvents. Their films had a cutoff wavelength between 358 and 373 nm, and the yellowness index ranged from 3.1 to 9.5. The glass‐transition temperatures of the poly(ether imide) series were recorded between 237 and 297 °C, the decomposition temperatures at 10% weight loss were all above 494 °C, and the residue was more than 54% at 800 °C in nitrogen. These films showed high tensile strength and also were characterized by higher solubility, lighter color, and lower dielectric constants and moisture absorption than an analogous nonfluorinated polyimide series. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3140–3152, 2006     

Fibrillar structure of resorbable microblock copolymers based on 1,5‐dioxepan‐2‐one and ε‐caprolactone

The copolymerization of 1,5‐dioxepan‐2‐one (DXO) and ε‐caprolactone, initiated by a five‐membered cyclic tin alkoxide initiator, was performed in chloroform at 60 °C. Copolymers with different molar ratios of DXO (25, 40, and 60%) were synthesized and characterized. ¹³C NMR spectroscopy of the carbonyl region revealed the formation of copolymers with a blocklike structure. Differential scanning calorimetry measurements showed that all the copolymers had a single glass transition between ?57 and ?49 °C and a melting temperature in the range of 30.1–47.7 °C, both of which were correlated with the amount of DXO. An increase in the amount of DXO led to an increase in the glass‐transition temperature and to a decrease in the melting temperature. Dynamic mechanical thermal analysis measurements confirmed the results of the calorimetric analysis, showing a single sharp drop in the storage modulus in the temperature region corresponding to the glass transition. Tensile testing demonstrated good mechanical properties with a tensile strength of 27–39 MPa and an elongation at break of up to 1400%. The morphology of the copolymers was examined with polarized optical microscopy and atomic force microscopy; the films that crystallized from the melt showed a short fibrillar structure (with a length of 0.05–0.4 μm) in contrast to the untreated solution‐cast films. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2412–2423, 2003     

Flame‐retardant epoxy resins with high glass‐transition temperatures. II. Using a novel hexafunctional curing agent: 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane

We synthesized a novel phosphorus‐containing triamine [9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐yl‐tris(4‐aminophenyl) methane (dopo‐ta)] from the nucleophilic addition of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide and pararosaniline chloride, using triethylamine as an acid receiver. We confirmed the structure of dopo‐ta by IR, mass, and NMR spectra and elemental analysis. dopo‐ta served as a curing agent for diglycidyl ether of bisphenol A (DGEBA) and dicyclopentadiene epoxy (hp7200). Properties such as the glass‐transition temperature (T_g), thermal decomposition temperature, flame retardancy, moisture absorption, and dielectric properties of the cured epoxy resins were evaluated. The T_g's of cured DGEBA/dopo‐ta and hp7200/dopo‐ta were 171 and 190 °C, respectively. This high T_g phenomenon is rarely seen in the literature after the introduction of a flame‐retardant element. The flame retardancy increased with the phosphorus content, and a UL‐94 V‐0 grade was achieved with a phosphorus content of 1.80 wt % for DGEBA/dopo‐ta/diamino diphenylmethane (DDM) systems and 1.46 wt % for hp7200/dopo‐ta/DDM systems. The dielectric constants for DGEBA/dopo‐ta and hp7200/dopo‐ta were 2.91 and 2.82, respectively, implying that the dopo‐ta curing systems exhibited low dielectric properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5971–5986, 2005     

Roll‐to‐Roll fabrication of large area functional organic materials

With the prospect of extremely fast manufacture of very low cost devices, organic electronics prepared by thin film processing techniques that are compatible with roll‐to‐roll (R2R) methods are presently receiving an increasing interest. Several technologies using organic thin films are at the point, where transfer from the laboratory to a more production‐oriented environment is within reach. In this review, we aim at giving an overview of some of the R2R‐compatible techniques that can be used in such a transfer, as well the current status of R2R application within some of the existing research fields such as organic photovoltaics, organic thin film transistors, light‐emitting diodes, polymer electrolyte membrane fuel cells, and electrochromic devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Soluble polyimides containing 1,4:3,6‐dianhydro‐d‐glucidol and fluorinated units: Preparation,characterization, optical,and dielectric properties

Aiming to develop soluble and colorless polyimides, two novel diamines, 2,5‐bis(2‐trifluoromethyl‐4‐amino‐phenoxy)‐1,4:3,6‐dianhydrosorbitol (2a) and 2,5‐bis(2‐methyl‐4‐amino‐phenoxy)‐1,4:3,6‐dianhydrosorbitol (2b), were designed and synthesized by the reduction of corresponding dinitro monomer which was obtained via solvent‐free melt heating method. Polyimides (PI–(1–5)) containing 1,4:3,6‐dianhydro‐d ‐glucidol fragments were prepared from 2a and five kinds of common dianhydrides and PI–6 was synthesized from 2b and 4,4′‐(hexafluoroisopropylidene)‐diphthalic anhydride (6FDA) via a two‐step thermal imidization. All the polyimides were readily soluble in common polar solvents and could afford flexible, tough, and transparent films with transparency as high as 87% at 450 nm. Meanwhile, PI–(1–6) exhibited unexpectedly low dielectric constants of 2.02–2.52 at 1 MHz. In addition, analogs PI–7 derived from 2,5‐bis(4‐amino‐phenoxy)‐1,4:3,6‐dianhydrosorbitol (2c) and 6FDA and PI–8 derived from 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl (2d) and 6FDA were also obtained via a two‐step thermal imidization for comparision with PI–(1–6) on aspects of thermal, mechnical, optical, electrical, and morphological properties. The structure–property relationships of PI–(1–8) were discussed in detail. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3253–3265     

Periodic extinction bands composed of all flat‐on lamellae in poly(dodecamethylene terephthalate) thin films crystallized at high temperatures

Using in‐house synthesized poly(dodecamethylene terephthalate) (P12T) as a model, periodic extinction‐banded spherulites melt‐crystallized at high T_cs (100–115 °C) are expounded in terms of growth mechanism. The extinction‐banded spherulites wildly differing from the usual blue/orange double ring‐banded spherulites are composed of all flat‐on discrete single‐crystalline lamellae packed like roof shingles (or fish scales) along the circularly curved bands and the lamellae in the extinction bands are flat with a lozenge shape with no continuous twisting at all. For P12T films of more than 10 µm crystallized at T_c = 105–115 °C, no periodic bands were seen, and all spherulites were ringless, where periodic growth precipitation of crystals to extinction does not occur until impingement. Extinction bands in the P12T spherulites with the inter‐ring spacing steadily decrease with decreasing film thickness, because for thinner films (submicrons to 2 µm), draining or depletion of available molten species takes place more frequently, leading to bands of smaller inter‐ring spacing. The petal‐like extinction bands are discussed and analyzed in detail using 3D AFM imaging. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 601–611     

Synthesis and properties of new aromatic polyimides based on 2,5‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐tert‐butylbenzene and various aromatic dianhydrides

A novel, fluorinated diamine monomer, 2,5‐bis(4‐amino‐2‐ trifluoromethylphenoxy)‐tert‐butylbenzene ( II ) was synthesized through the nucleophilic substitution reaction of tert‐butylhydroquinone (t‐BHQ) and 2‐chloro‐5‐nitrobenzotrifluoride in the presence of potassium carbonate to yield the intermediate dinitro compound I , followed by catalytic reduction with hydrazine and Pd/C to afford diamine II . A series of fluorinated polyimides V were prepared from II with various aromatic dianhydrides ( III _a–f ) via the thermal imidization of poly(amic acid). Most of V _a–f could be soluble in amide‐type solvents and even in less polar solvents. These polyimide films showed tensile strengths up to 106 MPa, elongation at break up to 21%, and initial modulus up to 2.1 GPa. The glass‐transition temperature of V was recorded at 245–304 °C, the 10% weight loss temperatures were above 488 °C, and left more than 41% residue even at 800 °C in nitrogen. Low dielectric constants, low moisture absorptions, and higher and light‐colored transmittances were also observed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5424–5438, 2004     

Influence of graphene oxide incorporation and chemical cross‐linking on structure and mechanical properties of layer‐by‐layer assembled poly(Vinyl alcohol)‐Laponite free‐standing films

Functional fillers in multilayered films provide opportunity in tailoring the mechanical properties through chemical cross‐linking. In this study, Laponite‐graphene oxide co‐dispersion was used to incorporate graphene oxide (GO) easily into polyvinyl alcohol (PVA)/Laponite layer‐by‐layer (LBL) films. The LBL films were found to be uniform and the layer thickness increased linearly with number of depositions. The process was extended to a large number of depositions to investigate the macroscopic mechanical properties of the free‐standing films. The LBL films showed remarkable improvements in mechanical properties as compared to neat PVA film. The GO‐incorporated LBL films displayed higher enhancements in the tensile strength, ductility, and toughness as compared to that of PVA/Laponite LBL films, upon chemical cross‐linking. This suggests the advantageous effects of GO incorporation. Interestingly, cross‐linking of LBL films for longer time period (>1 h) and higher temperature (～80 °C) was not found to be much beneficial. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2377–2387     

Poly[1‐(trimethylgermyl)‐1‐propyne] and poly[1‐(trimethylsilyl)‐1‐propyne] with various geometries: Their synthesis and properties

The polymerization of 1,2‐disubstituted acetylenes [1‐(trimethylgermyl)‐1‐propyne and 1‐(trimethylsilyl)‐1‐propyne] initiated by Nb‐ and Ta‐based catalytic systems was studied within a wide temperature range (?10 to +80 °C) with solvents (cyclohexane, CCl₄, toluene, anisol, and n‐chlorobutane) with variable dielectric constants (2.023–7.390). Conditions ensuring the synthesis of poly[1‐(trimethylsilyl)‐1‐propyne] (PTMSP) containing 20–80% cis units and poly[1‐(trimethylgermyl)‐1‐propyne] (PTMGP) containing 3–65% cis units were determined. The PTMSP and PTMGP samples were amorphous, exhibited a two‐phase structure characterized by the presence of less ordered regions and regions with an enhanced level of ordering, and differed in solubility. A correlation was found between the cis/trans ratio and the morphology, the geometrical density of PTMSP and PTMGP films, and the gas permeability of the polymers. The gas permeability and solubility behavior of PTMSP and PTMGP were examined in terms of the molecular characteristics of the polymer samples (the thermodynamic Kuhn segment and the Kerr electrooptic effect). It was demonstrated that the gas permeability, as well as the solubility of the polymers, was defined by their supramolecular ordering, which depended on the lengths of continuous sequences composed of units of analogous microstructures and on the flexibility of macrochains. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2133–2155, 2003     

Synthesis and properties of new polyarylates from 1,4‐bis(4‐carboxyphenoxy)naphthyl or 2,6‐bis(4‐carboxyphenoxy)naphthyl and various bisphenols

New 1,4‐naphthyl and 2,6‐naphthyl‐containing polyarylates having inherent viscosities up to 1.28 dL/g were synthesized by the high‐temperature solution polycondensation from the acid chloride of 1,4‐bis(4‐carboxyphenoxy)naphthyl or 2,6‐bis(4‐carboxyphenoxy)naphthyl and various bisphenols. Most of the resulting polyarylates showed amorphous characteristics and were readily soluble in common organic solvents such as N,N‐dimethylacetamide (DMAc), N‐methyl‐2‐pyrrolidone (NMP), o‐chlorophenol, and chloroform. Transparent, flexible, and colorless films of these polymers could be cast from the DMAc solutions. Their cast films had tensile strengths ranging from 54.9 to 84.2 MPa, elongations at break from 5.3% to 19.0%, and initial modulus from 2.0 to 2.8 GPa. These polymers had glass transition temperatures in the range of 172–280°C and began to lose weight around 400°C, with 10% weight loss being recorded at about 450°C in air. Dynamic mechanical analysis (DMA) reveals that the polyarylates containing isopropylidene linkages have three transitions on the temperature scale between −100 and 300°C. However, only two transitions were observed in the other polyarylates without isoproylidene linkage. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 645–652, 1999     

Preparation and properties of molecular‐weight‐controlled polyimides derived from 1,4‐bis(4′‐amino‐2′‐trifluoromethylphenoxy)benzene and 4,4′‐oxydiphthalic anhydride

A series of molecular‐weight‐controlled fluorinated aromatic polyimides were synthesized through the polycondensation of a fluorinated aromatic diamine, 1,4‐bis(4′‐amino‐2′‐trifluoromethylphenoxy)benzene, with 4,4′‐oxydiphthalic anhydride in the presence of phthalic anhydride as the molecular‐weight‐controlling and end‐capping agent. Experimental results demonstrated that the resulting polyimides could melt at temperatures of 250–300 °C to give high flowing molten fluids, which were suitable for melt molding to give strong and flexible polyimide sheets. Moreover, the aromatic polyimides also showed good solubility both in polar aprotic solvents and in common solvents. Polyimide solutions with solid concentrations higher than 25 wt % could be prepared with relatively low viscosity and were stable in storage at the ambient temperature. High‐quality polyimide films could be prepared via the casting of the polyimide solutions onto glass plates, followed by baking at a relatively low temperature. The molten behaviors and organosolubility of the molecular‐weight‐controlled aromatic polyimides depended significantly on the polymer molecular weights. Both the melt‐molded polyimide sheets and the solution‐cast polymer films exhibited outstanding combined mechanical and thermal properties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1997–2006, 2006     

Preparation and characterization of fluorine‐containing aromatic condensation polymers. VII. Aromatic polyacetals and copolyacetals from 2,2‐bis(4‐hydroxyphenyl)‐1,1,1,3,3,3‐hexafluoropropane and/or 2,2‐bis(4‐hydroxyphenyl)propane and 2‐(trifluoromethyl)benzal chloride

A series of fluorine‐containing aromatic homopolyacetals and copolyacetals with a wide range of unit ratios were synthesized by the solution polycondensation of 2,2‐bis(4‐hydroxyphenyl)‐1,1,1,3,3,3‐hexafluoropropane (bisphenol AF), 2,2‐bis(4‐hydroxyphenyl)propane (bisphenol A), or both with 2‐(trifluoromethyl)benzal chloride, and the effect of fluorine substitution on the properties of these polymers is discussed in relation to the fluorine contents. High molecular weight polyacetals with reduced viscosities of 0.43–0.97 dL/g were obtained in high yields with potassium hydroxide as a base, 18‐crown 6‐ether as a catalyst, and N‐methyl‐2‐pyrrolidinone as a medium at 100 °C for 3 h. Regardless of the fluorine contents, these polymers all were highly soluble in various solvents, including benzene, chloroform, ethyl acetate, and tetrahydrofuran, and afforded colorless, transparent, and tough films by solution casting. The temperatures of 5% weight loss and 10% weight loss under nitrogen both increased significantly and monotonously with increasing fluorine content, whereas the glass‐transition temperatures were scarcely affected by fluorine substitution. The dielectric constant at 1 MHz of the bisphenol AF‐based homopolyacetal was 2.43, which was remarkably lower than the value of the bisphenol A‐based homopolyacetal, 2.68. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1873–1879, 2000     

A facile approach to fabricate hierarchically structured poly(3‐hexylthiophene‐2,5‐diyl) films

Microstructured surfaces have great potentials to improve the performances and efficiency of optoelectronic devices. In this work, a simple robust approach based on surface instabilities was presented to fabricate poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) films with ridge‐like/wrinkled composite microstructures. Namely, the hierarchically patterned films were prepared by spin coating the P3HT/tetrahydrofuran (THF) solution on a polydimethylsiloxane (PDMS) substrate to form stable ridge‐like structures, followed by solvent vapor swelling to create surface wrinkles with the orientation guided by the ridge‐like structures. During spin coating of the P3HT/THF solution, the ridge‐like structures were generated by the in‐situ template of the THF swelling‐induced creasing structures on the PDMS substrate. To our knowledge, it is the first report that the creasing structures are used as a recoverable template for patterning films. The crease‐templated ridge‐like structures were well modulated by the THF swelling time, the modulus of the PDMS substrate, the P3HT/THF solution concentration and the selective/blanket exposure of the PDMS substrate to O₂ plasma. UV–vis and fluorescence spectrometry measurements indicated that the light absorption and fluorescent emission were improved on the hierarchically patterned P3HT films, which can be utilized to enhance the efficiencies of organic solar cells. Furthermore, this simple versatile method based on the solvent swelling‐induced crease as the in‐situ recoverable template has been extended to pattern other spin‐coated films with different compositions. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 928–939     

Cationic para‐phenyl‐substituted α‐diimine nickel catalyzed ethylene and 4‐methyl‐1‐pentene (co)polymerizations via living/controlled chain‐walking

Upon activation with diethylaluminium chloride (Et₂AlCl), a series of phenyl‐substituted α‐diimine nickel precatalysts conducted 4‐methyl‐1‐pentene (4MP) and ethylene (E) (co)polymerizations via controlled chain‐walking to generate branched amorphous polymers with high molecular weight and narrow molecular weight distribution (M_w/M_n < 1.6). The obtained poly(4MP)s were amorphous elastomers with glass transition temperature (T_g) of ?10 ~ ?24 °C, which are higher than that of E‐4MP copolymer ( ? 63.0 °C). At room temperature (25 °C), 4MP polymerization proceeds in a living manner. The microstructures of the produced poly(4MP)s indicated the 2,1‐ and 1,2‐insertion followed by chain‐walking, the latter being predominant. The NMR analyses of the polymers showed that the obtained poly(4MP) possessed methyl, isobutyl, 2,4‐dimethylpentyl and 2‐methylhexyl groups, while the isobutyl and 2,4‐dimethylalkyl branches derived from 4MP were observed in the E‐4MP copolymer. The branch structures and the insertion‐type of monomer were depended on the polymerization temperature, and the content of methyl branch increased with an increase in the polymerization temperature.     

Pulsed‐laser–deposited and plasma‐polymerized polytetrafluoroethylene (PTFE)‐like thin films: A comparative study on PTFE‐specific properties

Glass‐like and structural first‐order phase transitions are investigated in polytetrafluoroethylene (PTFE) foils and PTFE‐like films prepared by pulsed‐laser deposition (PLD) and plasma polymerization (PP). A structural comparison of the investigated polymers is performed by infrared spectroscopy and dielectric dilatometry. It is shown that dielectric dilatometry (the measurement of the susceptance vs. temperature) provides a simple and elegant means for detecting volumetric transitions in thin nonpolar polymer films. In conventional PTFE foils, the known glass‐like and structural first‐order phase transitions are identified. The structure of pulsed‐laser deposited PTFE strongly depends on the target material, ranging from highly crystalline films showing only structural phase transitions to films strongly deviating from PTFE foils, with structural characteristics comparable to plasma‐polymerized fluorocarbons. The dielectric loss of the highly crystalline PLD films compares favorably with conventional PTFE foils, making the films attractive for new applications in miniature electret devices. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2115–2125, 1999     

Synthesis and properties of ortho‐linked aromatic polyimides based on 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene

A bis(ether amine) containing the ortho‐substituted phenylene unit and pendant tert‐butyl group, 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene, was synthesized and used as a monomer to prepare polyimides with six commercial dianhydrides via a conventional two‐stage procedure. The intermediate poly(amic acid)s had inherent viscosities of 0.78–1.44 dL/g, and most of them could be thermally converted into transparent, flexible, and tough polyimide films. The inherent viscosities of the resulting polyimides were in the range of 0.46–0.87 dL/g. All polyimides were noncrystalline, and most of them showed excellent solubility in polar organic solvents. The glass‐transition temperatures of these polyimides were in the range of 222–259 °C in differential scanning calorimetry and 212–282 °C in thermomechanicl analysis. These polyimides showed no appreciable decomposition up to 500 °C in thermogravimetric analysis in air or nitrogen. A comparative study of the properties with the corresponding polyimides without pendant tert‐butyl groups derived from 1,2‐bis(4‐aminophenoxy)benzene is also presented. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1551–1559, 2000     

Phosphine‐free direct arylation synthesis and self‐assembled nanostructure analysis of poly(3‐hexylselenophene)

Poly(3‐hexylselenophene)s (P3Hs) with high regioregularity (RR = 92–96%), that is, regioregular poly(3‐hexylselenophene)s (rr‐P3HSs), have been synthesized under the phosphine‐free direct arylation conditions in the presence of PdCl₂ as a precatalyst. rr‐P3HS with the high molecular weight (M_n ～ 10,000) was obtained as a result of screening of direct arylation conditions. Subsequently, the influences of primary structure, molecular weight (M_n = 3900–10,000) and regioregularity (RR = 57–96%), on optical properties and self‐assembled nanostructure of P3HS were investigated. X‐ray diffraction demonstrated that molecular weight, regioregularity, and preparation method of films dominate the crystallization behavior of P3HS. Among these parameters, it was evident that a high degree of regioregularity was the most fundamental contributor to achieve pure crystalline nanostructure. Furthermore, nanoassembly based on pure crystalline nanostructure, such as non‐woven fibrous and bundle‐like spherulitic self‐assembled nanostructures, was successfully prepared in rr‐P3HS, respectively, by appropriate modulation of the aforementioned parameters. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2749–2755     

High‐molecular‐weight poly(1,2‐propylene succinate): A soft biobased polyester applicable as an effective modifier of poly(l‐Lactide)

Poly(1,2‐propylene succinate) (PPS) having high molecular weight can be synthesized by multi‐step melt‐polycondensation of succinic acid (SA) and 1,2‐propylene glycol (PG) with various catalysts. The first step is noncatalytic esterification/oligomerization of the two monomers, followed by the second step of catalytic melt‐polycondensation. In this step, co‐catalyst systems of Zn(AcO)₂/Ge(OBu)₄ and Zn(AcO)₂/Ti(BuO)₄ are effective for obtaining PPS having middle molecular weights (>10.0 kDa). This middle‐molecular‐weight PPS is chain‐elongated in the third‐step polycondensation with Zn(AcO)₂ as the catalyst to obtain a molecular weight reaching 120 kDa. As verified by ¹H‐ and ¹³C‐NMR spectra combined with two‐dimensional experiments, PPS has a ω‐bis‐hydroxy structure where the PG units leave the secondary hydroxyl terminals in larger ratio than the primary hydroxyl terminals. The PPS polymers are amorphous in nature, showing T_g around −4 °C. PPS can be solution‐ and melt‐blended with poly(l ‐lactide) (PLLA). By melt‐blending a high‐molecular‐weight PPS in an amount of 7.5–15 wt %, the modulus of the PLLA films decreases below 2000 MPa and the tear strength increases twice, supporting the effectiveness of PPS polymer in imparting flexible nature to PLLA. PPS polymers can therefore be applicable as elastomeric or flexible plastic modifiers having a 100 % biobased content. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1795–1805