Influence of primary ion species on the secondary cluster ion emission process from SAMs of hexadecanethiol on gold

In order to investigate the secondary cluster ion emission process of organo-metallic compounds under keV ion bombardment, self-assembled monolayers (SAMs) of alkanethiols on gold are ideal model systems. In this experimental study, we focussed on the influence of the primary ion species on the emission processes of gold-alkanethiolate cluster ions from a hexadecanethiol SAM on gold. For this purpose, we carried out time-of-flight secondary ion mass spectrometry (TOF-SIMS) measurements using the following primary ion species and acceleration voltages: Ar⁺, Xe⁺, SF₅⁺ (10 kV), Bi⁺, Bi₃⁺(25 kV), Bi₃²⁺, Bi₅²⁺, Bi₇²⁺ (25 kV).It is well known that molecular ions M⁻ and gold-alkanethiolate cluster ions Au_xM_y⁻ with M = S-(CH₂)₁₅-CH₃, x − 3 ≤ y ≤ x + 1, x, y > 0, show intense peaks in negative mass spectra. We derived yields Y_SI exemplarily for the molecular ions M⁻ and the gold-hexadecanethiolate cluster ions Au_y+1M_y⁻ up to y = 8 and found an exponentially decreasing behaviour for increasing y-values for the cluster ions.In contrast to the well-known increase in secondary ion yield for molecular secondary ions when moving from lighter to heavier (e.g. Ar⁺ to Xe⁺) or from monoatomic to polyatomic (e.g. Xe⁺ to SF₅⁺) primary ions, we find a distinctly different behaviour for the secondary cluster ions. For polyatomic primary ions, there is a decrease in secondary ion yield for the gold-hexadecanethiolate clusters whereas the relative decrease of the secondary ion yield ξ_Y with increasing y remains almost constant for all investigated primary ions.     

Polyethylene terephthalate (PET) bulk film analysis using C60, Au3, and Au primary ion beams

The damage characteristics of polyethylene terephthalate (PET) have been studied under bombardment by C₆₀⁺, Au₃⁺ and Au⁺ primary ions. The observed damage cross-sections for the three ion beams are not dramatically different. The secondary ion yields however were significantly enhanced by the polyatomic primary ions where the secondary ion yield of the [M + H]⁺ is on average 5× higher for C₆₀⁺ than Au₃⁺ and 8× higher for Au₃⁺ than Au⁺. Damage accumulates under Au⁺ and Au₃⁺ bombardment while C₆₀⁺ bombardment shows a lack of damage accumulation throughout the depth profile of the PET thick film up to an ion dose of ∼1 × 10¹⁵ ions cm⁻². These properties of C₆₀⁺ bombardment suggest that the primary ion will be a useful molecular depth profiling tool.     

Thiolated cyclodextrin self-assembled monolayer-like characterized with secondary ion mass spectrometry

In the work the focus is on the preparation of self-assembled monolayer-like films consisting of thiolated cyclodextrin on gold substrate and a characterization by using secondary ion mass spectrometry. The short (1 min) and long (1 h) time preparations of self-assembled monolayer-like films, resulting in submonolayer and monolayer regimes, are investigated, respectively. The observed species of thiolated cyclodextrin (M as molecular ion) self-assembled monolayer-like films are assigned to three groups: Au_xH_yS_z clusters, fragments with origin in cyclodextrin molecule associated with Au, and molecular ions. The group of Au_xH_yS_z (x = 2-17, y = 0-2, z = 1-5) clusters have higher intensities than other species in the positive and even more in negative mass spectra. Interestingly, the dependence between the number of Au and S atoms shows that with the increasing size of Au_xH_yS_z clusters up to 11 Au atoms, the number of associated S atoms is also increasing and then decreasing. Molecular species as (M−S+H)Na⁺, (M+H)Na⁺, AuMNa⁺, (M₂−S)Na⁺, and M₂Na⁺ are determined, and also in cationized forms with K⁺. The intensities of thiolated cyclodextrin fragments at the long time preparation are approximately 10 times higher than the intensities of the same fragments observed at the short time. The largest observed ions in thiolated cyclodextrin self-assembled monolayer-like films are AuM₂ and Au₂M. The thiolated cyclodextrin molecular ions are compared with hexadecanethiol molecular ions in the form of Au_xM_w where the values of x and w are smaller for thiolated cyclodextrin than for hexadecanethiol. This result is supported with larger, more compact, and more stabile thiolated cyclodextrin molecule.     

Investigation of molecular weight effects of polystyrene in ToF-SIMS using C60 and Au primary ion beams

In secondary ion mass spectrometry, polyatomic primary ion sources are known to enhance yields from many surfaces including polymers. In order to understand the fundamental causes for these increases, the enhancement as a function of material type and molecular weight needs to be delineated. In this article, we report results from a systematic investigation of polymeric films of polystyrene (PS) with varying molecular weights to examine the influence of the primary ion beam on the secondary ion yields in time of flight secondary ion mass spectrometry (ToF-SIMS). The masses of the polymers investigated ranged from 1000 to 20,000 Da, or from about n = 10 to 200 where n indicates the number of polymeric units in a polymer chain. The polymers had a narrow molecular weight range (PDI < 1.07). The multilayer polymeric films (10-30 nm) characterized by AFM were prepared by spin-casting onto silicon substrates and were analyzed using Au⁺ and C₆₀⁺ primary ion beams. The analysis with the two beams provided a useful comparison between atomic and polyatomic primary ion sources. Information gathered from this study provides insight into the role of molecular weight on the observed yield enhancement from polyatomic ion sources.     

Molecular ion yield enhancement induced by gold deposition in static secondary ion mass spectrometry

Static ToF-SIMS was used to evaluate the effect of gold condensation as a sample treatment prior to analysis. The experiments were carried out with a model molecular layer (Triacontane M = 422.4 Da), upon atomic (In⁺) and polyatomic (Bi₃⁺) projectile bombardment. The results indicate that the effect of molecular ion yield improvement using gold metallization exists only under atomic projectile impact. While the quasi-molecular ion (M+Au)⁺ signal can become two orders of magnitude larger than that of the deprotonated molecular ion from the pristine sample under In⁺ bombardment, it barely reaches the initial intensity of (M−H)⁺ when Bi₃⁺ projectiles are used. The differences observed for mono- and polyatomic primary ion bombardment might be explained by differences in near-surface energy deposition, which influences the sputtering and ionization processes.     

Comparison of detection efficiencies of negatively charged gold-alkanethiolate-, gold-sulfur- and gold-clusters in ToF-SIMS

In order to improve quantification of high mass ions, the influence of cluster composition on detection efficiencies has been studied using a TOF-SIMS IV with the extended capability of postaccelerating ions up to 20 keV. In this experimental study, we focus on the comparison of detection efficiencies for three types of negatively charged secondary cluster ions: gold-alkanethiolate-clusters (Au_xM_y), gold-sulfur-clusters (Au_xS_y) and gold-clusters (Au_x). The clusters were sputtered from self-assembled monolayers of hexadecanethiols on gold substrates using 10 keV Ar⁺ primary ions. The detection efficiencies were derived on the basis of a function for the secondary electron yield and a fourth-order approximated Poisson probability distribution for electron propagation and amplification within the microchannel plate.In addition to the well-known dependence of detection efficiencies on ion mass and energy, which has already been studied for positively charged ions, we were able to show a similar behaviour for the investigated negatively charged secondary ions. We have observed major variations among the three types of clusters at similar mass and energy as predicted in a theoretical approach. The observed differences are due to the different composition of the investigated clusters which has a major influence on the kinetic ion induced electron emission within the microchannel plate. For the first time it was possible to experimentally verify these predictions for detection efficiencies.     

Subthreshold kaon production in Au on Au collisions at 1 GeV/u

Subthreshold kaon production in¹⁹⁷ Au+¹⁹⁷ Au collisions at 1.0 GeV/u has been investigated with the Kaon Spectrometer at SIS. At _lab =44±4 we found aK ⁺/p ratio of>3 · 10^–4 for the momentum range 650 MeV/c to 1150 MeV/c.Dedicated to Prof. Dr. P. Kienle on the occasion of his 60th birthday     

Primary ion fluence dependence in time-of-flight SIMS of self-assembled monolayer of alkyl thiol molecules on Au(1 1 1)—Discussion of static limit

The nondestructive nature of static secondary ion mass spectrometry (SIMS) in the context of studies of self-assembled monolayers (SAMs) of organic molecules has been examined by measuring the primary ion fluence dependence of secondary ion signals with two well-known SAMs, C₁₈H₃₇SH on Au(1 1 1) and C₁₈H₃₇PO₃H₂ on freshly cleaved mica. This SIMS analysis is challenging because the bonding nature is delicate and the areal molecular density is less than 10¹⁵ cm⁻². In SIMS, it is prevalently assumed that if the primary ion fluence is confined to not more than 1 × 10¹² cm⁻², all secondary ion signals should not change by more than 10% and the practically defined static condition is satisfied. Our results from time-of-flight SIMS with the common primary ions of Bi₃⁺, Bi⁺ and Ar⁺, indicate that this prevalent static assumption fails for both model SAMs. The SIMS results from the phosphyl case, which have been recently published, consistently display the evidence of bombardment-induced damage. In comparison, the thiol case presented here shows much more complex primary ion fluence dependence of SIMS signals. It is therefore concluded that practical static analysis should use primary ion fluence not more than 1 × 10¹¹ cm⁻² or should simply record and report the effects of primary ion fluence.     

Prompt fission induced by antiproton annihilation at rest on heavy nuclei

Antiproton induced fission probabilities of U²³⁸, Bi²⁰⁹, Pb²⁰⁸ and Au¹⁷⁷ are reported together with the mass distribution of the fission fragments in the U²³⁸ and Bi²⁰⁹ cases. The charged particles multiplicities observed in co-incidence with fission have, also, been measured for U and Bi and are presented.Dedicated to Peter Armbruster on the occasion of his 60th birthday in recognition of his important contribution to modern Nuclear Physics     

Analysis of TOF-SIMS spectra from fullerene compounds

We analyzed TOF-SIMS spectra obtained from three different size of fullerenes (C₆₀, C₇₀ and C₈₄) by using Ga⁺, Au⁺ and Au₃⁺ primary ion beams and investigated the fragmentation patterns, the enhancement of secondary ion yields and the restraint of fragmentation by using cluster primary ion beams compared with monoatomic primary ion beams. In the TOS-SIMS spectra from C₇₀ and C₈₄, it was found that a fragment ion, identified as C₆₀⁺ (m/z = 720), showed a relatively high intensity compared with that of other fragment ions related to C₂ depletion. It was also found that the Au₃⁺ bombardment caused intensity enhancement of intact molecules (C₆₀⁺, C₇₀⁺ and C₈₄⁺) and restrained the fragmentation due to C₂ depletion.     

Comparison of secondary ion intensity enhancement from polymers on silicon and silver substrates by using Au-TOF-SIMS

The usefulness of the usage of cluster primary ion source together with an Ag substrate and detection of Ag cationized molecular ions was studied from the standpoint to realize high sensitivity TOF-SIMS analysis of organic materials. Although secondary ions from polymer thin films on a Si substrate can be detected in a higher sensitivity with Au₃⁺ cluster primary ion compared with Ga⁺ ion bombardment, it was clearly observed that the secondary ion intensities from samples on an Ag substrate showed quite a different tendency from that on Si. When monoatomic primary ions, e.g., Au⁺ and Ga⁺, were used for the measurement of the sample on an Ag substrate, [M+Ag]⁺ ions (M corresponds to polyethylene glycol molecule) were detected in a high sensitivity. On the contrary, when Au₃⁺ was used, no intensity enhancement of [M+Ag]⁺ ions was observed. The acceleration energy dependence of the detected secondary ions implies the different ionization mechanisms on the different substrates.     

Substrate effects on the analysis of biomolecular layers using Au, Au3 and C60 bombardments

Effects of platinum silicon, graphite and PET substrates on the secondary ion yield of sub-monolayer and multilayer samples of Cyclosporin A following 20 keV Au⁺, Au₃⁺and C₆₀⁺ impacts have been investigated. The obtained results of sub-monolayer samples show that platinum enhances the yield of the pseudo-molecular ion following Au⁺ and Au₃⁺ impacts due to the high density of the substrate that enables the energy of the primary ions to be deposited near the surface. C₆₀⁺ impacts on sub-monolayer samples are less effective, but there is an enhancement on PET substrates. Impacts of 20 keV Au⁺ and Au₃⁺ are not very efficient on multilayer samples. 20 keV C₆₀⁺ impacts enhance the yields significantly, especially for the relatively high molecular weight [M+H]⁺ ion.     

Dissociative photoionization of l-menthone: An experimental and theoretical study

The dissociative photoionization mechanism of l-menthone has been investigated with photoionization mass spectrometry using synchrotron radiation. The adiabatic ionization energy (IE) of l-menthone and the appearance energies (AE) of its major fragment ions C₉H₁₅O⁺, C₉H₁₇⁺, C₈H₁₆⁺, C₇H₁₁O⁺, C₆H₁₀O⁺, C₆H₉O⁺, C₅H₈O⁺, C₅H₁₀⁺, C₄H₆O⁺, C₅H₉⁺, C₄H₈⁺, C₄H₇⁺, C₃H₇⁺, C₃H₆⁺, C₂H₂O⁺, and CH₃⁺ are determined with their photoionization efficiency (PIE) spectra in the photon energy region of ∼8−15.5 eV. Breakdown diagrams identifying the major products are presented. Dissociative photoionization channels for formation of these fragment ions are proposed based on comparison of determined experimental appearance energies and energies predicted with the DFT calculations. According to our results, the experimental dissociation energies are in fair agreement with the theoretical values of the possible photodissociation channels of C₁₀H₁₈O.     

Metal-assisted SIMS and cluster ion bombardment for ion yield enhancement

In addition to structural information, a detailed knowledge of the local chemical environment proves to be of ever greater importance, for example for the development of new types of materials as well as for specific modifications of surfaces and interfaces in multiple fields of materials science or various biomedical and chemical applications. But the ongoing miniaturization and therefore reduction of the amount of material available for analysis constitute a challenge to the detection limits of analytical methods. In the case of time-of-flight secondary ion mass spectrometry (TOF-SIMS), several methods of secondary ion yield enhancement have been proposed. This paper focuses on the investigation of the effects of two of these methods, metal-assisted SIMS and polyatomic primary ion bombardment. For this purpose, thicker layers of polystyrene (PS), both pristine and metallized with different amounts of gold, were analyzed using monoatomic (Ar⁺, Ga⁺, Xe⁺, Bi⁺) and polyatomic (SF₅⁺, Bi₃⁺, C₆₀⁺) primary ions. It was found that polyatomic ions generally induce a significant increase of the secondary ion yield. On the other hand, with gold deposition, a yield enhancement can only be detected for monoatomic ion bombardment.     

DC-60 heavy ion cyclotron complex: The first beams and project parameters

The construction of the DC-60 Heavy Ion Cyclotron for the Interdisciplinary Scientific Research Complex (ISRC) in Astana started in early 2004. The cyclotron was manufactured and tested at the Flerov Laboratory of Nuclear Reactions (FLNR) in Dubna. The main units were delivered to Astana and assembled in the ISRC building in the summer of 2006. The cyclotron was turned on in September, 2006. The first heavy ion beams in the whole A/Z and energy ranges were accelerated and extracted in December, 2006. The complex, based on the DC-60 cyclotron, is intended for applied and fundamental research using accelerated heavy ion beams ranging from Carbon to Xenon with energies in the range of 0.34–1.77 MeV/nucleon, as well as for experiments on the channel of low energy ion beams, where the ion extraction voltage supplied by the ECR source reaches 25 kV. The energy variation of the accelerated ions is accomplished by changing the ion charge. The possibility of smoothly tuning the ion energy by ±30% of its nominal value can be seen by changing the cyclotron magnetic field. Within the framework of commissioning the DC-60 cyclotron, a number of experiments were carried out with accelerating charged particle beams in the main points of the working diagram

Erratum to Formation and control of Au and Ag nanoparticles inside borate glasses using femtosecond laser and heat treatment

We report the spectroscopic properties of femtosecond laser-irradiated sodium-alumino-borate glass doped with silver and gold ions. We precipitated gold and silver nanoparticles by laser irradiation and annealing at 400°C for 30 min. The irradiation and annealing treatment produced different absorption and emission characteristics in Au³⁺ doped and Au³⁺, Ag⁺ codoped glasses, and the possible mechanisms of the observed results are discussed. The size of the nanoparticles was estimated by TEM and absorption band analysis.     

Structure, electrical properties and temperature characteristics of?Bi0.5Na0.5TiO3–Bi0.5K0.5TiO3–Bi0.5Li0.5TiO3 lead-free piezoelectric ceramics

(1−x−y)Bi_0.5Na_0.5TiO₃–xBi_0.5K_0.5TiO₃– yBi_0.5Li_0.5TiO₃ lead-free piezoelectric ceramics have been prepared by an ordinary sintering technique, and their structure, electrical properties, and temperature characteristics have been studied systematically. The ceramics can be well-sintered at 1050–1150 °C. The increase in K⁺ concentration decreases the grain-growth rate and promotes the formation of grains with a cubic shape, while the addition of Li⁺ decreases greatly the sintering temperature and assists in the densification of BNT-based ceramics. The results of XRD diffraction show that K⁺ and Li⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a solid solution with a pure perovskite structure. As x increases from 0.05 to 0.50, the ceramics transform gradually from rhombohedral phase to tetragonal phase and consequently a morphotropic phase boundary (MPB) is formed at 0.15≤x≤0.25. The concentration y of Li⁺ has no obvious influence on the crystal structure of the ceramics. Compared with pure Bi_0.5Na_0.5TiO₃, the partial substitution of K⁺ and Li⁺ for Na⁺ lowers greatly the coercive field E _c and increases the remanent polarization P _r of the ceramics. Because of the MPB, lower E _c and large P _r, the piezoelectricity of the ceramics is improved significantly. For the ceramics with the compositions near the MPB (x=0.15–0.25 and y=0.05–0.10), the piezoelectric properties become optimum: piezoelectric coefficient d ₃₃=147–231 pC/N and planar electromechanical coupling factor k _P=20.2–41.0%. In addition, the ceramics exhibit relaxor characteristic, which probably results from the cation disordering in the 12-fold coordination sites. The depolarization temperature T _d shows a strong dependence on the concentration x of K⁺ and reaches the lowest values at the MPB. The temperature dependences of the ferroelectric and dielectric properties at high temperatures may imply that the ceramics may contain both the polar and non-polar regions at temperatures above T _d.     

Non-interferometric transient quantitative phase microscopy for ultrafast engineering

Lead-free piezoelectric ceramics Bi_0.5(Na_1-x-yK_xAg_y)_0.5TiO₃ [BNKAT(x/y)] have been synthesized by the mixed oxide method. The effects of the amount of K⁺ and Ag⁺ on the electrical properties were examined. X-ray diffraction patterns indicate that K⁺ and Ag⁺ ions partially substitute for the Na⁺ ions in Bi_0.5Na_0.5TiO₃ and form a solid solution during sintering. At room temperature, the ceramics exhibit good performances with piezoelectric constant d₃₃=189 pC/N, electromechanical coupling factor k_p=35.0%, remanent polarization P_r=39.5 μC/cm², and coercive field E_c=3.3 kV/mm, respectively. The curves of the dielectric constant ε_r and loss tangent tan δ versus temperature show that the transition temperature from ferroelectric to anti-ferroelectric phase decreases with increasing the K⁺ content for the compositions researched. The dependencies of k_p and polarization versus electric (P–E) hysteresis loops on temperature reveal that the depolarization temperature T_d of BNKAT(0.15/0.015) ceramics, which have good piezoelectric properties (d₃₃=134 pC/N, k_p=32.5%) and strong ferroelectricity (P_r=39.5 μC/cm², E_c=4.1 kV/mm) at room temperature, is above 160 °C. PACS 77.22.-d; 77.65.Bn; 77.80.Bh; 77.80.Dj; 77.84.Dy     

Substrate dependence of ion motion in femtosecond laser ablation cloud observed by planar laser-induced fluorescence

We have observed the motion of Sm⁺ ions as well as Sm atoms produced by femtosecond laser ablation of a solidified samarium solution sample on substrates by using a planar laser-induced fluorescence method. Kinetic energies of both Sm⁺ ions and Sm atoms increase as the electrical conductivity of the substrate decreases, which suggests the effect of surface charging. The kinetic energy of Sm⁺ ions is larger than that of Sm atoms for a variety of substrates due to the further electrical acceleration by the surface charge. The knowledge of ion motion will be the key information for the optimization of femtosecond laser simultaneous atomization and ionization of organic and inorganic samples on substrates.     

Using polyatomic primary ions to probe an amino acid and a nucleic base in water ice

In this study on pure water ice, we show that protonated water species [H₂O]_nH⁺ are more prevalent than (H₂O)_n⁺ ions after bombardment by Au⁺ monoatomic and Au₃⁺ and C₆₀⁺ polyatomic projectiles. This data also reveals significant differences in water cluster yields under bombardment by these three projectiles. The amino acid alanine and the nucleic base adenine in solution have been studied and have been shown to have an effect on the water cluster ion yields observed using an Au₃⁺ ion beam.