Blocky poly(ɛ‐caprolactone‐co‐butylene 2,5‐furandicarboxylate) copolyesters via enzymatic ring opening polymerization

Cyclic oligo(butylene 2,5‐furandicarboxylate) and ɛ‐caprolactone were copolymerized in bulk at 130–150 °C by enzymatic ring opening polymerization using CALB as catalyst. Copolyesters within a wide range of compositions were thus synthesized with weight‐average molecular weights between 20,000 and 50,000, the highest values being obtained for equimolar or nearly equimolar contents in the two components. The copolyesters consisted of a blocky distribution of the ɛ‐oxycaproate (CL) and butylene furanoate (BF) units that could be further randomized by heating treatment. The thermal stability of these copolyesters was comparable to those of the parent homopolyesters (PBF and PCL), and they all showed crystallinity in more or less degree depending on composition. Their melting and glass‐transition temperatures were ranging between those of PBF and PCL with values increasing almost linearly with the content in BF units. The ability of these copolyesters for crystallizing from the melt was evaluated by comparative isothermal crystallization and found to be favored by the presence of flexible ɛ‐oxycaproate blocks. These copolyesters are essentially insensitive to hydrolysis in neutral aqueous medium but they became noticeably degraded by lipases in an extend that increased with the content in CL units. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 290–299     

Crystallinity and crystalline phase orientation of poly(1,4‐cis‐isoprene) from Hevea brasiliensis and Taraxacum kok‐saghyz

Crystallization is studied for poly(isoprene‐1,4‐cis) from Hevea brasiliensis (natural rubber [NR]) and from taraxacum kok‐saghyz, mainly by collecting wide‐angle X‐ray diffraction patterns after processing and stretching. Although rubber samples before stretching are generally fully amorphous, crystallization can be induced in NR samples by processing at room temperature under moderate pressure. This phenomenon is possibly associated with nucleation by saturated fatty acid components. For rubber samples being fully amorphous in the undeformed state, strain‐induced crystallization occurs only at high strain ratios (α > 4), leading to high degrees of crystalline phase orientation (f_c > 0.9 for α = 5). Rubber samples presenting some crystallinity already in the unstretched state, on the contrary, reach much lower degrees of axial orientation, even for high strain ratios (f_c < 0.7 for α = 5). These differences in crystallinity and in crystalline phase orientations produce large differences in stress–strain behavior of the rubber. By room temperature processing, the considered NR samples can also develop an unreported disordered crystalline modification, with low intensity of 120 and 121 reflections. This disordered crystalline modification, which is also maintained after axial stretching procedures, can rationalized by a structural disorder along the b axis, possibly associated with statistical sequences of A⁺TA^? or A^?T A⁺ conformations for poly(isoprene‐1,4‐cis) chains. Copyright © 2016 John Wiley & Sons, Ltd.     

Strain‐induced crystallization and mechanical properties of functionalized graphene sheet‐filled natural rubber

The effects of functionalized graphene sheets (FGSs) on the mechanical properties and strain‐induced crystallization of natural rubber (NR) are investigated. FGSs are predominantly single sheets of graphene with a lateral size of several hundreds of nanometers and a thickness of 1.5 nm. The effect of FGS and that of carbon black (CB) on the strain‐induced crystallization of NR is compared by coupled tensile tests and X‐ray diffraction experiments. Synchrotron X‐ray scattering enables simultaneous measurements of stress and crystallization of NR in real time during sample stretching. The onset of crystallization occurs at significantly lower strains for FGS‐filled NR samples compared with CB‐filled NR, even at low loadings. Neat‐NR exhibits strain‐induced crystallization around a strain of 2.25, while incorporation of 1 and 4 wt % FGS shifts the crystallization to strains of 1.25 and 0.75, respectively. In contrast, loadings of 16 wt % CB do not significantly shift the critical strain for crystallization. Two‐dimensional (2D) wide angle X‐ray scattering patterns show minor polymer chain alignment during stretching, in accord with previous results for NR. Small angle X‐ray scattering shows that FGS is aligned in the stretching direction, whereas CB does not show alignment or anisotropy. The mechanical properties of filled NR samples are investigated using cyclic tensile and dynamic mechanical measurements above and below the glass transition of NR. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

New polymer syntheses. 107. Aliphatic poly(thio ester)s by ring‐opening polycondensation of 2‐stanna‐1,3‐dithiacycloalkanes

We prepared 2,2‐dibutyl‐2‐stanna‐1,3‐dithiacycloalkanes from dibutyltin oxide and α,ω‐dimercaptoalkanes. Heterocycles with five‐, six‐, seven‐, or nine‐ring members were used as bifunctional monomers for polycondensations with aliphatic dicarboxylic acid chlorides. These polycondensations conducted in bulk were highly exothermic and yielded poly(thio ester)s with number average molecular weights (M_n's) in the range of 5000–30,000 Da. These poly(thio ester)s proved to be rapidly crystallizing materials with melting temperatures in the range of 90–150 °C. In addition to the success of the new synthetic approach, two interesting and unpredictable results were obtained. All volatile species detectable by matrix assisted laser desorption induced‐time of flight (MALDI‐TOF) mass spectrometry were cyclic oligo‐ and poly(thio ester)s. Second, several polyesters showed a reversible first‐order change of the crystal modification as identified by differential scanning calorimetry measurements and X‐ray scattering with variation of the temperature. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3656–3664, 2000     

Thermal analysis of the multiple melting behavior of poly(butylene succinate‐co‐adipate)

The melting behavior of poly(butylene succinate‐co‐adipate) (PBSA) isothermally crystallized from the melt was investigated by differential scanning calorimetry. Triple, double, or single melting endotherms were observed in subsequent heating scan for the samples isothermally crystallized at different temperatures. These endothermic peaks were labeled as I, II, and III for low‐, middle‐, and high‐temperature melting endotherms, respectively. The independence of endotherm III to the crystallization temperature, the existence of an exothermic crystallization peak just below the endotherm III, and the heating rate dependence of endotherm III indicated that endotherm III was due to the remelting of recrystallized lamellar during a heating scan. The influence of crystallization time on the melting behavior of PBSA showed that endotherms II and III developed prior to endotherm I; endotherm III developed rather simultaneously with endotherm II. Further investigation showed that the peak temperature of endotherm I increased linearly with the logarithm of the crystallization time. It suggested that endotherm II was attributed to the melting of the primary lamellae, while endotherm I was due to the melting of secondary lamellae. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3077–3082, 2005     

Crystallization kinetics and melting behavior of syndiotactic 1,2‐polybutadiene

Differential scanning calorimetry was used to investigate the isothermal crystallization, subsequent melting behavior, and nonisothermal crystallization of syndiotactic 1,2‐polybutadiene (st‐1,2‐PB) produced with an iron‐based catalyst system. The isothermal crystallization of two fractions was analyzed according to the Avrami equation. The morphology of the crystallite was observed with polarized optical microscopy. Double melting peaks were observed for the samples isothermally crystallized at 125–155 °C. The low‐temperature melting peak, which appeared approximately 5 °C above the crystallization temperature, was attributed to the melting of imperfect crystals formed by the less stereoregular fraction. The high‐temperature melting peak was associated with the melting of perfect crystals formed by the stereoregular fraction. With the Hoffman–Weeks approach, the value of the equilibrium melting temperature was derived. During the nonisothermal crystallization, the Ozawa method was limited in obtaining the kinetic parameters of st‐1,2‐PB. A new method that combined the Ozawa method and the Avrami method was employed to analyze the nonisothermal crystallization of st‐1,2‐PB. The activation energies of crystallization under nonisothermal conditions were calculated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 553–561, 2005     

Synthesis and characterization of poly(L‐lactic acid)–poly(ε‐caprolactone) multiblock copolymers by melt polycondensation

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(22) 5845 New multiblock copolymers derived from poly(L‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) were prepared with the coupling reaction between PLLA and PCL oligomers with ? NCO terminals. Fourier transform infrared (FTIR), ¹³C NMR, and differential scanning calorimetry (DSC) were used to characterize the copolymers and the results showed that PLLA and PCL were coupled by the reaction between ? NCO groups at the end of the PCL and ? OH (or ? COOH) groups at the end of the PLLA. DSC data indicated that the different compositions of PLLA and PCL had an influence on the thermal and crystallization properties including the glass‐transition temperature (T_g), melting temperature (T_M), crystallizing temperature (T_c), melting enthalpy (ΔH_m), crystallizing enthalpy (ΔH_c), and crystallinity. Gel permeation chromatography (GPC) was employed to study the effect of the composition of PLLA and PCL and reaction time on the molecular weight and the molecular weight distribution of the copolymers. The weight‐average molecular weight of PLLA–PCL multiblock copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL, whereas that of the homopolymer of PLLA was only 14,000. A polarized optical microscope was used to observe the crystalline morphology of copolymers; the results showed that all polymers exhibited a spherulitic morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5045–5053, 2004     

Initial lamellar thickness dependency of recrystallization behavior of poly(4‐methyl‐1‐pentene)

The isothermal crystallization and subsequent melting process in semicrystalline poly(4‐methyl‐1‐pentene) were investigated via temperature‐dependent small‐ and wide‐angle X‐ray scattering and Flash DSC techniques. In a phase diagram of inversed crystalline lamellar thickness and temperature, the crystallization and melting lines can be described by two linear dependencies of different slopes and different limiting temperatures at infinite lamellar thickness. Upon subsequent heating, recrystallization lines with different slopes were observed for samples with different lamellar thickness, indicating changes in surface free energy difference between stabilized crystallites and mesomorphic phase. The surface free energy of native crystallites with extended‐chain conformation decreased with increasing lamellar thickness due to a more ordered surface region and less chain ends which changes cooperatively with mesomorphic phase. The surface free energy of stabilized crystallites remained unchanged for all lamellar thickness. Therefore, the recrystallization lines with different slopes are consequences of changes in surface free energy of mesomorphic phase. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 219–224     

Poly(ester amide)/clay nanocomposites prepared by in situ polymerization of the sodium salt of N‐chloroacetyl‐6‐aminohexanoic acid

Preparation of nanocomposites of organo‐modified montmorillonites and the biodegradable poly(ester amide) derived from glycolic acid and 6‐aminohexanoic acid has been evaluated by the in situ polymerization technique. The reaction was based on the thermal polycondensation of sodium chloroacetylaminohexanoate, which has the formation of the sodium chloride salt as the driving force of the process. Polymerized samples were studied by means of X‐ray diffraction and transmission electron microscopy. The most dispersed structure was obtained by addition of C25A organoclay. Evaluation of thermal stability and crystallization behavior of these samples showed significant differences between the neat polymer and its nanocomposite with C25A. Isothermal and nonisothermal calorimetric analyses of the polymerization reaction revealed that the kinetics was highly influenced by the presence of the silicate particles. Crystallization of the polymer was observed to occur when the process was isothermally conducted at temperatures lower than 145 °C. In this case, dynamic FTIR spectra and WAXD profiles obtained with synchrotron radiation were essential to study the polymerization kinetics. Clay particles seemed to reduce chain mobility and the Arrhenius preexponential factor. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3616–3629, 2009     

Inorganic–organic hybrids involving poly(ε‐caprolactone) and silica network: Hydrogen‐bonding interactions and isothermal crystallization kinetics

Inorganic–organic hybrids mediated by hydrogen‐bonding interactions involving silicon oxide network and poly(ε‐caprolactone) (PCL) were prepared via an in situ sol–gel process of tetraethoxysilane in the presence of PCL. Fourier transform infrared spectroscopy indicated that there were hydrogen‐bonding interactions between carbonyls of PCL and silanol hydroxyls that were formed by incomplete polycondensation in the sol–gel process. In terms of the frequency shift of the hydroxyl stretching vibration bands, it is concluded that the strength of the interassociation between PCL and silicon oxide networks is weaker than that of the self‐association in the control silica network. The phenomenon of equilibrium melting point depression was observed for the PCL/silica system. The hybridization of PCL with silica network causes a considerable increase in the overall crystallization rate and dramatically influences the mechanism of nucleation and growth of the PCL crystallization. The analysis of isothermal crystallization kinetic data according to the Hoffman‐Lauritzen theory shows that with increasing silica content in the hybrids, the surface energy of extremity surfaces increases dramatically for the hybrids. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2594–2603, 2005     

Synthesis and characterization of poly(higher‐α‐olefin)s with a nickel(α‐diimine)/methylaluminoxane catalyst system: Effect of chain running on the polymer properties

Homopolymerization of octadecene‐1 at different reaction conditions has been studied. Significant chain running can be seen at higher polymerization temperatures. Interestingly, insertion of octadecene‐1 into a sterically hindered nickel‐cation/carbon (secondary) bond is observed. The microstructure of the polymer was established using NMR spectroscopy. The effects of chain running on polymer melting, crystallization behavior, and dynamic mechanical thermal properties were studied using DSC and DMTA. The extent of chain running (i.e., 2,ω‐, 1,ω‐enchainments) decreases with an increase in the carbon number of α‐olefins. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 191–210, 2007     

Melting behavior,crystallization kinetics,and crystal structure of poly(2‐hydroxyethoxybenzoate)

The melting behavior and crystallization kinetics of poly(2‐hydroxyethoxybenzoate) (PHEBA) were investigated with differential scanning calorimetry and hot‐stage optical microscopy. The observed multiple endotherms, commonly displayed by polyesters, were influenced by the crystallization temperature. By the application of the Hoffman–Weeks method to the melting temperatures of isothermally crystallized samples, a value of 232 °C was obtained for the equilibrium melting temperature. Isothermal crystallization kinetics were analyzed according to Avrami's treatment. Values of Avrami's exponent n close to 3 were obtained, independently of the crystallization temperature, in agreement with a crystallization process originating from predetermined nuclei and characterized by three‐dimensional spherulitic growth. In fact, space‐filling banded spherulites were observed by hot‐stage optical microscopy at all crystallization temperatures explored, with the band spacing increasing with increasing crystallization temperature. The rate of crystallization became lower as the crystallization temperature increased as usual at low undercooling, with the crystallization process controlled by nucleation. The equilibrium heat of fusion was determined by differential scanning calorimetry and wide‐angle X‐ray scattering measurements. Finally, the crystal phase of PHEBA was investigated with wide‐angle X‐ray scattering, and a triclinic unit cell was hypothesized. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1354–1362, 2002     

Crystallization and melting of isotactic polypropylene crystallized from quiescent melt and stress‐induced localized melt

Temperature dependency of crystalline lamellar thickness during crystallization and subsequent melting in isotactic polypropylene crystallized from both quiescent molten state and stress‐induced localized melt was investigated using small angle X‐ray scattering technique. Both cases yield well‐defined crystallization lines where inverse lamellar thickness is linearly dependent on crystallization temperature with the stretching‐induced crystallization line shifted slightly to smaller thickness direction than the isothermal crystallization one indicating both crystallization processes being mediated a mesomorphic phase. However, crystallites obtained via different routes (quiescent melt or stress‐induced localized melt) show different melting behaviors. The one from isothermal crystallization melted directly without significant changing in lamellar thickness yielding well‐defined melting line whereas stress‐induced crystallites followed a recrystallization line. Such results can be associated with the different extent of stabilization of crystallites obtained through different crystallization routes. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 957–963     

Development of amorphous copolyesters based on 1,4‐cyclohexanedimethanol

The modification of poly(ethylene terephthalate) with 1,4‐cyclohexanedimethanol and the modification of poly(1,4‐cyclohexylenedimethylene terephthalate) with ethylene glycol or isophthalic acid retard the crystallization of the copolyester backbone, and over a wide range of comonomer concentrations, very slowly crystallizing, essentially amorphous copolyesters are formed. These amorphous copolyesters possess attractive physical properties such as toughness, low color, and chemical resistance, and since their first commercial introduction in 1977, these copolyesters have become the basis of a large and growing plastics business for Eastman Chemical Co. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5847–5852, 2004     

Preparation of single‐walled carbon nanotubes‐induced poly(p‐oxybenzoyl) crystals

Crystallization of oligomers was applied for the preparation of single‐walled carbon nanotubes (SWNTs)/poly(p‐oxybenzoyl) (POB) crystals using SWNTs as a nucleating agent. Polymerization conditions were investigated to induce the crystallization of POB oligomers through SWNTs. SWNTs/POB plate‐like or lozenge‐shaped crystals were successfully prepared by direct polymerization of p‐hydroxybenzoic acid (HBA) in a mixed solvent of DMF/Py with TsCl in the presence of functionalized SWNTs. The size of the plate‐like crystals were ～200 nm to 3 μm. The crystals consisted of some layers, ～3 nm thick plates. Model reactions showed that esterification reactions proceed between functionalized SWNTs and HBA monomers in the polymerization system. The obtained crystals exhibited unique morphology and high crystallinity, producing a novel SWNT/POB hybrid. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1265–1277, 2008     

Polydispersity of ethylene sequence length in metallocene ethylene/α‐olefin copolymers. II. Influence on crystallization and melting behavior

In this work, crystallization and melting behavior of metallocene ethylene/α‐olefin copolymers were investigated by differential scanning calorimetry (DSC) and atomic force microscopy (AFM). The results indicated that the crystallization and melting temperatures for all the samples were directly related to the long ethylene sequences instead of the average sequence length (ASL), whereas the crystallization enthalpy and crystallinity were directly related to ASL, that is, both parameters decreased with a decreasing ASL. Multiple melting peaks were analyzed by thermal analysis. Three phenomena contributed to the multiple melting behaviors after isothermal crystallization, that is, the melting of crystals formed during quenching, the melting‐recrystallization process, and the coexistence of different crystal morphologies. Two types of crystal morphologies could coexist in samples having a high comonomer content after isothermal crystallization. They were the chain‐folded lamellae formed by long ethylene sequences and the bundlelike crystals formed by short ethylene sequences. The coexistence phenomenon was further proved by the AFM morphological observation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 822–830, 2002     

Molecular heterogeneity of ethylene‐propylene rubbers: New insights through advanced crystallization‐based and chromatographic techniques

For a long time ethylene‐propylene rubber (EPR) copolymers with high comonomer contents were believed to be amorphous materials with a random copolymer composition. This is not completely correct as has been shown by temperature rising elution fractionation (TREF) combined with differential scanning calorimetry (DSC), crystallization analysis fractionation (CRYSTAF), and high temperature–high‐performance liquid chromatography (HT‐HPLC). When using only conventional crystallization‐based fractionation methods, the comprehensive compositional analysis of EPR copolymers was impossible due to the fact that large fractions of these copolymers do not crystallize under CRYSTAF conditions. In the present work, HT‐HPLC was used for the separation of the EPR copolymers according to their ethylene and propylene distributions along the polymer chains. These investigations showed the existence of long ethylene sequences in the bulk samples which was further confirmed by DSC. The results on the bulk samples prompted us to conduct preparative fractionations of EPR copolymers having varying ethylene contents using TREF. Surprisingly, significant amounts of crystallizing materials were obtained that were analyzed using a multistep protocol. CRYSTAF and DSC analyses of the TREF fractions revealed the presence of components with large crystallizable sequences that had not been detected by the bulk samples analyses. HT‐HPLC provided a comprehensive separation and characterization of both the amorphous and the crystalline TREF fractions. The TREF fractions eluting at higher temperatures showed the presence of ethylene‐rich copolymers and PE homopolymer. In order to obtain additional structural information on the separated fractions, HT‐HPLC was coupled to Fourier transform‐infrared (FT‐IR) spectroscopy. The FT‐IR data confirmed that the TREF fractions were separated according to the ethylene contents of the eluted samples. Preparative TREF analysis together with a combination of various analytical methods proved to be useful tools in understanding the complex molecular composition of these rubber samples. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 863–874     

Analysis of crystallization behavior and crystal modifications of poly(butylene‐2,6‐naphthalene dicarboxylate)

Information on the crystalline structure and the properties of poly(butylene‐2,6‐naphthalene dicarboxylate) (PBN) has not been well reported until now, but it is known that there are two different crystal modifications in PBN, as follows: one is formed in isotropic samples by annealing (α form); another appears by annealing with tension (β form). The relation between the crystal modifications and the kinetics of isothermal crystallization for PBN was investigated using in‐situ Fourier transform infrared spectroscopy (FTIR) and wide‐angle X‐ray diffraction (WAXD). The melting behavior of each crystalline form was also studied by means of FTIR and differential scanning calorimetry (DSC) measurements. From the analysis of the melt‐crystallized PBN specimens, the two crystalline forms coexisted in the isotropic samples melt‐crystallized at 230°C, but only the α crystal modification was observed in the films annealed at lower temperatures. In addition, it was revealed that, at 230°C, the β modification was formed only in the primary crystallization process. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 561–574, 1999     

Thermal properties of poly(alkylene dicarboxylate)s derived from 1,12‐dodecanedioic acid and even aliphatic diols

A series of new aliphatic polyesters derived from 1,12‐dodecanedioic acid and different diols with an even number of methylene units have been studied to assess the effect of the chemical structure on the final thermal properties of the materials. The polyesters have high thermal stability and are fast crystallizing polymers, with crystallization rate similar to that of polyethylene (PE). This behavior is connected to the fact that long aliphatic chains assume conformational characteristics very similar to that of PE. However, the polyester prepared from ethanediol shows a peculiar behavior (for example, double melting peak, melting and crystallization temperatures, which do not fit the trend of those of the other samples and ringed spherulites) owing to a probable different conformation, deviating from the all‐trans planar typical of PE. In the isothermal crystallization studies, a bell‐shape trend has been found for the crystallization rate as a function of the number of ? (CH₂)? units in the diol. The high crystallization rate of the sample with long ? (CH₂)? sequences has been attributed to the high chain flexibility and, thus, high mobility in the molten state and ease of chain folding. By reducing the aliphatic sequence length, instead, implications of the structural characteristics of the samples are probably involved. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1053–1067, 2007