On-line complexation/cloud point preconcentration for the sensitive determination of dysprosium in urine by flow injection inductively coupled plasma–optical emission spectrometry

An on-line dysprosium preconcentration and determination system based on the hyphenation of cloud point extraction (CPE) to flow injection analysis (FIA) associated with ICP-OES was studied. For the preconcentration of dysprosium, a Dy(III)-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol complex was formed on-line at pH 9.22 in the presence of nonionic micelles of PONPE-7.5. The micellar system containing the complex was thermostated at 30 degrees C in order to promote phase separation, and the surfactant-rich phase was retained in a microcolumn packed with cotton at pH 9.2. The surfactant-rich phase was eluted with 4 mol L(-1) nitric acid at a flow rate of 1.5 mL min(-1), directly in the nebulizer of the plasma. An enhancement factor of 50 was obtained for the preconcentration of 50 mL of sample solution. The detection limit value for the preconcentration of 50 mL of aqueous solution of Dy was 0.03 microg L(-1). The precision for 10 replicate determinations at the 2.0 microg L(-1)Dy level was 2.2% relative standard deviation (RSD), calculated from the peak heights obtained. The calibration graph using the preconcentration system for dysprosium was linear with a correlation coefficient of 0.9994 at levels near the detection limits up to at least 100 microg L(-1). The method was successfully applied to the determination of dysprosium in urine.     

纳米TiO2微柱分离富集测定环境样品中的微量硒

以处理过的纳米TiO2为微柱吸附材料,采用流动注射技术进行微量硒的分离富集,考察了纳米TiO2微柱对Se(IV)的吸附性能,探讨了溶液的pH值、试样流速、试样体积、洗脱液浓度和用量以及干扰离子等因素的影响。实验结果表明,pH在1～6范围内,试样流速为0.5 mL/min,纳米TiO2对Se(IV)具有良好的吸附性能,吸附率可达97%,动态饱和吸附容量为7.92 mg/g;选用1 mL 0.1 mol/L NaOH溶液可将吸附的Se(IV)完全洗脱,富集倍数为40。本法的检出限(3σ)为0.13 mg/L,相对标准偏差为1.56 %。将本法应用于国家标准样品GBW07280的分析,测定值与参考值一致。     

Application of high-surface-area ZrO2 in preconcentration and determination of 18 elements by on-line flow injection with inductively coupled plasma atomic emission spectrometry

A flow-injection analysis (FIA) system incorporating a micro-column of ZrO2 has been used for the development of an on-line multi-element method for the simultaneous preconcentration and determination of Al, Bi, Cd, Co, Cr, Cu, Fe, Ga, In, Mn, Mo, Ni, Pb, Tl, V, Sb, Sn, and Zn by inductively coupled plasma atomic emission spectrometry (ICP-AES). The conditions for quantitative and reproducible preconcentration, elution, and subsequent on-line ICP-AES determination were established. A sample (pH 8) is pumped through the column at 3 mL min(-1) and sequentially eluted directly into the ICP-AES with 3 mol L(-1) HNO3. With a sample volume of 100 mL and an elution volume of 1 mL signal enhancement 100 times better than for conventional continuous aspirating systems was obtained for the elements studied. The reproducibility (RSD %) of the method at the 10 ng mL(-1) level in the eluate is acceptable - less than 8% for five replicates. Recoveries between 95.4% and 99.9% were obtained for the elements analysed. ZrO2, with a specific surface area of 57 m2 g(-1) and a capacity of approximately 5 mg g(-1) for the elements studied, was synthesized by hydrolysis of ZrCl4. The preconcentration system was evaluated for several simple synthetic matrices, standard water samples and synthetic seawater. The effect of foreign ions on the efficiency of preconcentration of the elements studied was investigated. The application of a micro-column filled with high-surface-area ZrO2 and flow injection inductively coupled plasma atomic emission spectrometry enables preconcentration and simultaneous determination of 18 elements at low concentrations (ng L(-1)) in different water samples.     

Heat-treated Saccharomyces cerevisiae for antimony speciation and antimony(III) preconcentration in water samples

An analytical method was developed for antimony speciation and antimony(III) preconcentration in water samples. The method is based on the selective retention of Sb(III) by modified Saccharomyces cerevisiae in the presence of Sb(V). Heat, caustic and solvent pretreatments of the biomass were investigated to improve the kinetics and thermodynamics of Sb(III) uptake process at room temperature. Heating for 30 min at 80 degrees C was defined as the optimal treatment. Antimony accumulation by the cells was independent of pH (5-10) and ionic strength (0.01-0.1 mol L(-1)). 140 mg of yeast and 2h of contact were necessary to ensure quantitative sequestration of Sb(III) up to 750 microg L(-1). In these conditions, Sb(V) was not retained. Sb(V) was quantified in sorption supernatant by inductively coupled plasma mass spectrometry (ICP-MS) or inductively coupled plasma optical emission spectrometry (ICP-OES). Sb(III) was determined after elution with 40 mmol L(-1) thioglycolic acid at pH 10. A preconcentration factor close to nine was achieved for Sb(III) when 100mL of sample was processed. After preconcentration, the detection limits for Sb(III) and Sb(V) were 2 and 5 ng L(-1), respectively, using ICP-MS, 7 and 0.9 microg L(-1) using ICP-OES. The proposed method was successfully applied to the determination of Sb(III) and Sb(V) in spiked river and mineral water samples. The relative standard deviations (n=3) were in the 2-5% range at the tenth microg L(-1) level and less than 10% at the lowest Sb(III) and Sb(V) tested concentration (0.1 microg L(-1)). Corrected recoveries were in all cases close to 100%.     

Determination of trace amounts of lead in mussels by flow-injection flame atomic-absorption spectrometry coupled with on-line minicolumn preconcentration

A minicolumn packed with poly(aminophosphonic acid) chelating resin incorporated in an on-line preconcentration system for flame atomic-absorption spectrometry was used to determine ultratrace amounts of lead in mussel samples at microg L(-1) level. The preconcentrated lead was eluted with hydrochloric acid and injected directly into the nebulizer for atomization in an air-acetylene flame for measurement. The performance characteristics of the determination of lead were: preconcentration factor 26.8 for 1 min preconcentration time, detection limit (3sigma) in the sample digest was 0.25 microg g(-1) (dry weight) for a sample volume of 3.5 mL and 0.2 g sample (preconcentration time 1 min), precision (RSD) 2.3% for 25 microg L(-1) and 2.0% for 50 microg L(-1). The sampling frequency was 45 h(-1). The method was highly tolerant of interferences, and the results obtained for the determination of lead in a reference material testify to the applicability of the proposed procedure to the determination of lead at ultratrace level in biological materials such as mussel samples.     

Electrothermal atomic absorption spectrometric determination of cobalt in biological samples and natural waters using a flow injection system with on-line preconcentration by ion-pair adsorption in a knotted reactor

An on-line flow injection preconcentration-ETAAS method is developed for trace determination of cobalt in biological materials and natural samples by ion-pair sorption on the inner walls of a PTFE knotted reactor. The ion-pair is formed between the negatively charged cobalt-nitroso-R-salt complex and the tetrabutylammonium counter-ion. An enhancement factor of 15, a sampling frequency of 17 and a concentration efficiency of 4 are obtained for a preconcentration time of 60 s and a sample loading flow rate of 5 mL min(-1). The detection limit (3sigma) is 5 ng L(-1). The relative standard deviation at the 0.2 microg L(-1) level is 2.3%. The analytical results obtained for standard reference materials are in good agreement with the certified or indicated values and satisfactory recoveries of spiked cobalt in tap water are obtained.     

On-line separation and preconcentration of silver ion on amidino-thiourea immobilized glass beads packing in flow injection analysis with atomic absorption spectrometric detection.

Amidino-thiourea immobilized glass beads (AGB I) were prepared and used as the microcolumn packing for the flow injection (FI) on-line separation and preconcentration of Ag(I) coupled with atomic absorption spectrometry (AAS) determination. Base metal ions and anions with a concentration of 2.0 mg mL(-1) had no interference with the determination of Ag(I). The limit of detection (LOD) of Ag(I) for a preconcentration time of 60 s with a sampling flow rate of 5.0 mL min(-1) for 40.0 ng mL(-1) of Ag(I) were 0.50 ng mL(-1) with the peak-height absorbance mode and 1.26 ng mL(-1) with the peak-area absorbance mode, respectively. The relative standard deviations (RSD) of 7 replicate determinations were 0.9% and 0.7% for the peak-height absorbance (H) and the peak-area absorbance (A), respectively. The method was successfully applied to the determination of Ag(I) in ore samples.     

纳米TiO2微柱分离富集测定环境样品中的微量碲

以处理过的纳米TiO2为微柱吸附材料,采用流动注射技术进行微量碲的分离富集,探讨了溶液的pH值、试样流速、试样体积、洗脱液浓度和用量以及干扰离子等因素的影响。 实验结果表明,pH值在8～9.5范围内,纳米TiO2对Te(Ⅳ)具有良好的吸附性能,吸附率接近99%,动态饱和吸附容量为37.02 mg/g;选用2 mL 0.5 mol/L NaOH溶液可将吸附的Te(Ⅳ)完全洗脱,富集倍数为30。 本法的检出限(3σ)为0.013 mg/L,相对标准偏差为RSD=1.99%。 将本法应用于水样的分析,碲的回收率在98%~103%之间,结果令人满意。     

Preconcentration of methylxanthines on hyper-cross-linked polystyrene followed by their determination by high-performance liquid chromatography

We studied the possibility of hyper-cross-linked polystyrene application to the dynamic sorption preconcentration (solid-phase extraction) of methylxanthines (caffeine, theophylline, theobromine, diprophylline, and pentoxifylline) from aqueous solutions. The conditions of preconcentration were optimized as follows: solution volume of 25 mL (pH ～ 6), solution flow rate 0.7 mL/min, microcolumn size 25 × 2.7 mm, adsorbent weight 0.055 g. The compounds were desorbed into a 0.5-mL portion of methanol and determined in the eluate by reversed-phase HPLC with spectrophotometric detection at 280 nm. Sorption preconcentration provided more than 30-fold reduction of methylxanthine detection limits. The detection limits for methylxanthines are 1 (theophylline, theobromine), 2 (caffeine, diprophylline) and 4 (pentoxifylline) ng/mL. The procedure was applied to the analysis of urine-based model mixtures.     

Amberlite XAD-7 impregnated with Xylenol Orange: a chelating collector for preconcentration of Cd(II), Co(II), Cu(II), Ni(II), Zn(II) and Fe(III) ions prior to their determination by flame AAS

A new chelating resin, Xylenol Orange coated Amberlite XAD-7, was prepared and used for preconcentration of Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) prior to their determination by flame atomic absorption spectrophotometry. The optimum pH values for quantitative sorption of Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) are 4.5-5.0, 4.5, 4.0-5.0, 4.0, 5.0 and 5.0-7.0, respectively, and their desorptions by 2 mol L(-1) HCl are instantaneous. The sorption capacity of the resin has been found to be 2.0, 2.6, 1.6, 1.6, 2.6 and 1.8 mg g(-1) of resin for Cd, Co, Cu, Fe, Ni and Zn, respectively. The tolerance limits of electrolytes, NaCl, NaF, NaI, NaNO3, Na2SO4 and of cations, Mg2+ and Ca2+ in the sorption of the six metal ions are reported. The preconcentration factor was between 50 and 200. The t1/2 values for sorption are found to be 5.3, 2.9, 3.2, 3.3, 2.5 and 2.6 min for the six metals, respectively. The recoveries are between 96.0 and 100.0% for the different metals at preconcentration limits between 10 to 40 ng mL(-1). The preconcentration method has been applied to determine the six metal ions in river water samples after destroying the organic matter (if present in very large amount) with concentrated nitric acid (RSD < or = 8%, except for Cd for which it is upto 12.6%) and cobalt content of vitamin tablets with RSD of approximately 3.0%.     

Quinoline-8-ol-immobilized Amberlite XAD-4: synthesis,characterization, and uranyl ion uptake properties suitable for analytical applications

Amberlite XAD-4 has been functionalized by coupling it with 5-aminoquinoline-8-ol after acetylation. The resulting resin has been characterized by elemental analysis and IR spectra and has been used for preconcentrating uranyl ions prior to its determination by spectrophotometry. The optimum pH value for quantitative sorption is 4-6, and desorption can be achieved by using 5 mL of 1 mol L(-1) HCl. The sorption capacity of the resin is 11.5 mmol g(-1). The effect of various cations and anions on the preconcentration of uranium in conjunction with the determination procedure has been studied and we have found that none of the ions interfere except thorium. The enrichment factor for preconcentration of uranium was found to be 200. Ten replicate determinations of 40 micro g of uranium present in 1 L of sample gave a mean absorbance of 0.185 with a relative standard deviation of 2.64%. The detection limit corresponding to three times the standard deviation of the bank was found to be 2 micro g L(-1). The validation of the developed preconcentration procedure was carried out by successfully analyzing standard marine sediment reference material. The uranyl content of sediment and soils is estimated by spectrophotometry after its preconcentration with the above chelating resin.     

Applicability of multisyringe chromatography coupled to on-line solid-phase extraction to the simultaneous determination of dicamba, 2,4-D, and atrazine

Simultaneous determination of three herbicides (dicamba, 2,4-D, and atrazine) has been achieved by on-line solid-phase extraction (SPE) coupled to multisyringe chromatography (MSC) with UV detection. The preconcentration conditions were optimized; a preconcentration flow rate of 0.5 mL min(-1) and elution at 0.8 mL min(-1) were the optimum conditions. A C(18) (8 mm i.d.) membrane extraction disk conditioned with 0.3 mol L(-1) HCl in 0.5% MeOH was used. A 3-mL sample was preconcentrated, then eluted with 0.43 mL 40:60 water-MeOH. A C(18) monolithic column (25 mm × 4.6 mm) was used for chromatographic separation. Separation of the three compounds was achieved in 10 min by use of 0.01% aqueous acetic acid-MeOH (60:40) as mobile phase at a flow rate of 0.8 mL min(-1). The limits of detection (LOD) were 13, 57, and 22 μg L(-1) for dicamba, 2,4-D, and atrazine, respectively. The sampling frequency was three analyses per hour, and each analysis consumed only 7.3 mL solvent. The method was applied to spiked water samples, and recovery between 85 and 112% was obtained. Recovery was significantly better than in the conventional HPLC-UV method. These results indicated the reliability and accuracy of this flow-based method. This is the first time this family of herbicides has been simultaneously analyzed by on-line SPE-MSC using a monolithic column.     

离子印迹壳聚糖/凹土分离富集-火焰原子吸收光谱测定中药材中痕量Cd(Ⅱ)的研究

建立了离子印迹壳聚糖/凹凸棒石(IICA)分离富集-火焰原子吸收光谱(FAAS)测定中药材中痕量Cd(Ⅱ)的新方法。在动态吸附条件下,系统研究了溶液pH值、流速、洗脱条件和干扰离子对痕量Cd(Ⅱ)分离富集的影响。研究表明,在pH为4.5,上样流速为0.60mL/min条件下,Cd(Ⅱ)能被IICA定量富集;吸附的Cd(Ⅱ)可用1.0mol/L HCl-0.1mol/L甲基异丁酮的乙醇溶液,在流速为0.96mL/min条件下完全洗脱。优化条件下,IICA对Cd(Ⅱ)的动态吸附容量为56.45mg/g。线性范围为0.00097～1.28mg/L,r=0.9994,检出限(3σ,n=11)为0.97μg/L,相对标准偏差为1.32%(n=6,c=0.08mg/L),回收率在96.5%～106.4%之间。该方法操作简便,灵敏度和精密度高,可应用于实际中药材样品中痕量镉的测定。     

Determination of trace cadmium in waters by flame atomic absorption spectrophotometry after preconcentration with 1-nitroso-2-naphthol-3,6-disulfonic acid on Ambersorb 572

A procedure for the determination of trace amount of cadmium after adsorption of its 1-nitroso-2-naphthol-3,6-disulfonic acid chelate on Ambersorb 572 has been proposed. This chelate is adsorbed on the adsorbent in the pH range 3-8 from large volumes of aqueous solution of water samples with a preconcentration factor of 200. After being sorbed, cadmium was eluted by 5 mL of 2.0 mol L(-1) nitric acid solution and determined directly by flame atomic absorption spectrophotometery (FAAS). The detection limit (3sigma) of cadmium was 0.32 microg L(-1). The precision of the proposed procedure, calculated as the relative standard deviation of recovery in sample solution (100 mL) containing 5 microg of cadmium was satisfactory (1.9%). The adsorption of cadmium onto adsorbent can formally be described by a Langmuir equation with a maximum adsorption capacity of 19.6 mg g(-1) and a binding constant of 6.5 x 10(-3) L mg(-1). Various parameters, such as the effect of pH and the interference of a number of metal ions on the determination of cadmium, have been studied in detail to optimize the conditions for the preconcentration and determination of cadmium in water samples. This procedure was applied to the determination of cadmium in tap and river water samples.     

Determination of trace indium in urine after preconcentration with a chelating-resin-packed minicolumn

A simple and rapid chelating-resin-packed column has been developed for preconcentration of trace indium in biological samples. A large-sized urine sample was pumped through a minicolumn at a flow rate of 1.0 mL/min by using a peristaltic pump, and the eluents were analyzed using graphite furnace atomic absorption spectrometry (GFAAS). Four commercially available chelating resins including Chelex-100, Amberlite IRC-50, Duolite GT-73, and Celite 545-AW were studied for evaluating the indium sorption performance. Several parameters, such as pH, resin amount, eluent volume, eluent flow rate, and the volume of sample, were investigated and optimized. A 100-200 mL of the sample was loaded into a column containing 1.2 g of wet Chelex-100 and subjected to the ion-exchange procedure. The retained analytes were eluted with 5.0 mL of 0.1 M HNO(3) and quantified by GFAAS. The correlation coefficient in the range 10-250 ng/mL was of 0.9994. The limit of detection of the proposed method was 2.75 ng/mL. The method developed was successfully applied to analysis of spiked urine samples with good recoveries of 93-103% (n = 6) and reproducibility (relative standard deviation < 4.9%). The accuracy of procedure was confirmed by indium determination in spiked certified reference materials.     

Field preconcentration of cadmium from seawater by using a minicolumn packed with Amberlite XAD-4/4-(2-pyridylazo) resorcinol and its flow-injection-flame atomic absorption spectrometric determination at the ng L(-1) Level

A flow injection analysis-flame atomic absorption spectrometric method for the determination of cadmium in seawater was developed with the aim of yielding a sensitive assay with a low detection limit. The method employs a field flow preconcentration technique involving a minicolumn containing Amberlite XAD-4 impregnated with the complexing agent 4-(2-pyridylazo) resorcinol. A Plackett-Burman 2(7)x3/32 design for seven factors (sample pH, sample flow rate, eluent volume, eluent concentration, eluent flow rate, ethanol percentage in the eluent and minicolumn diameter) was carried out in order to find the significant variables affecting the field continuous preconcentration system (FCPS) and the flow injection elution manifold for cadmium determination in seawater samples by flame atomic absorption spectrometry. Cadmium can be preconcentrated with an enrichment factor of 1053 for a sample volume of 200 mL and a preconcentration time of 57 min. In these experimental conditions, the method provides a linear relationship between absorbance and cadmium concentration in the range from 22-1900 ng L(-1), with a detection limit (3SD) of 6 ng L(-1). The precision (expressed as relative standard deviation) for eleven independent determinations reached values of 8.9-0.8% in cadmium solutions of 50-700 ng L(-1). Analysis of certified reference materials (SLEW-3 and NASS-5) showed good agreement with the certified value. This procedure was applied to the determination of cadmium in seawater from Galicia (Spain).     

Determination of ultratrace elements in natural waters by solid-phase extraction and atomic spectrometry methods

A study was carried out on the preconcentration of ultratrace amounts of cadmium, lead, manganese, copper and iron from high-salinity aqueous samples and determination by atomic spectrometry methods. Sample volume, amount of resin, loading flow rate, and elution volume were optimized in order to obtain the simultaneous preconcentration of all the analytes. Quantitative recoveries were obtained by using 200 mg of iminodiacetic resin with a loading flow rate of 2 mL min(-1), elution volume of 3 mL and sample volume of 50-450 mL. Only copper in seawater samples was not completely retained by the resin (60-70% recovery), due to unfavorable competition of iminodiacetic-active groups with organically bound metal.To quantify the metals in the eluates, two atomic spectrometry techniques were compared: electrothermal atomization atomic absorption spectrometry (ETAAS) and inductively coupled plasma-optical emission spectrometry (ICP-OES) with simultaneous CCD detection system. Both techniques are suitable for sample analysis with detection limits of 1.0, 4.7, 3.3, 6.8, and 53 ng L(-1) using ETAAS and 12, 122, 3.4, 17, and 21 ng L(-1) using ICP-OES for Cd, Pb, Mn, Cu, and Fe, respectively. Relative standard deviations of the procedures ranged from 1.7 to 14% at the sub-microg L(-1) concentration level. The accuracy of both methods was verified by analyzing various certified reference materials (river water, estuarine water, coastal and off-shore seawater).     

Atomic absorption spectrometric determination of trace amounts of copper and zinc after simultaneous solid-phase extraction and preconcentration onto modified natrolite zeolite.

This work assesses the use of modified natural natrolite zeolite as an adsorptive material for the separation and preconcentration of trace amounts of ions. In this work we investigated the potential of modified natural natrolite zeolite for the simultaneous separation and preconcentration of trace amounts of copper and zinc ions. We have developed a simple, rapid, selective, sensitive and economical method for the simultaneous separation and preconcentration of trace amounts of copper and zinc in an aqueous medium using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) as an analytical reagent. The sorption was quantitative in the pH range 7.5 - 9.5, whereas quantitative desorption occurred instantaneously with 5.0 mL of 2 mol L(-1) nitric acid. Linearity was maintained between 0.05 - 6.0 microg mL(-1) for copper and 0.02 - 1.5 microg mL(-1) for zinc in the final solution. Ten replicate determinations of 1.0 microg mL(-1) copper and 0.5 microg mL(-1) zinc in a mixture gave mean absorbances of 0.1687 and 0.2788 with relative standard deviations of +/-1.2% and +/-1.3%, respectively. The detection limits were 0.03 ng mL(-1) for Cu(II) and 0.006 ng mL(-1) for Zn(II) in the original solution (3 sigma(bl)/m). Different parameters, such as the effect of the pH, flow rate, breakthrough volume and interference of a large number of anions and cations, were studied and the proposed method was used for the determination of these metal ions in water as well as standard samples (e.g. Nippon Keikinzoku Kogyo (NKK) CRM, No. 916 and No. 920 aluminum alloy, National Institute for Environment Studies (NIES) No. 1 pepperbush and NIES No. 2 pond sediment). The determination of these metal ions in standard samples showed that the proposed method has good accuracy (recovery > 97%).     

直接衍生离子液体富集高效液相色谱分析水基胶中脂肪族醛酮

建立了以2,4-二硝基苯肼(DNPH)直接衍生,1-丁基-3-甲基咪唑六氟磷酸盐(［BMIM］PF6)萃取富集,高效液相色谱(HPLC)分析水基胶中痕量脂肪族醛酮的方法。分散的水基胶乳液用80 mg/L DNPH衍生化试剂(含0.44 mol/L磷酸)于40 ℃衍生18 min。取离心后的上层衍生液,加入0.5 mL ［BMIM］PF6于30 ℃萃取富集,离子液体相过滤后进行HPLC分析。采用Dionex Acclaim Explosives E2色谱柱(250 mm×4.6 mm, 5 μm),以水-乙腈为流动相在流速1.2 mL/min进行梯度洗脱,色谱柱温度为35 ℃,检测波长为365 nm。结果表明,8种脂肪族醛酮的检出限为0.022～0.221 mg/kg,定量限为0.073～0.738 mg/kg,相对标准偏差为3.5%～7.3%,回收率为84.0%～102.5%。与溶剂萃取法相比,该法具有检出限和定量限低、稳定性高、测定更准确的优势。     

Preconcentration of phenols on a polymethacrylate sorbent for their gas-chromatographic determination in water

The preconcentration of phenol and its homologues by sorption on a polymethacrylate sorbent followed by capillary gas-chromatographic determination is studied. The optimal sorption conditions are the following: the sorbent mass, 400 mg; the volume of aqueous solution with pH 3, 150 mL; the flow rate of solution, 3–4 mL/min; and the volume of ethylacetate for elution, 3 mL. The detection limit is 0.7–1.0 μg/mL.