Sonochemical synthesis of cobalt aluminate nanoparticles under various preparation parameters

Cobalt aluminate (CoAl₂O₄) nanoparticles were synthesized using a precursor method with the aid of ultrasound irradiation under various preparation parameters. The effects of the preparation parameters, such as the sonochemical reaction time and temperature, precipitation agents, calcination temperature and time on the formation of CoAl₂O₄ were investigated. The precursor on heating yields nanosized CoAl₂O₄ particles and both these nanoparticles and the precursor were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM). The use of ultrasound irradiation during the homogeneous precipitation of the precursor reduces the duration of the precipitation reaction. The mechanism of the formation of cobalt aluminate was investigated by means of Fourier transformation infrared spectroscopy (FT-IR) and EDX (energy dispersive X-ray). The thermal decomposition process and kinetics of the precursor of nanosized CoAl₂O₄ were investigated by means of differential scanning calorimetry (DSC) and thermogravimetry (TG). The apparent activation energy (E) and the pre-exponential constant (A) were 304.26 kJ/mol and 6.441 × 10¹⁴ s^?1, respectively. Specific surface area was investigated by means of Brunauer Emmett Teller (BET) surface area measurements.     

Ultrasound-assisted mineralization of organic contaminants using a recyclable LaFeO3 and Fe3+/persulfate Fenton-like system

A recyclable heterogeneous catalyst has been successfully developed for application in a Fenton-type advanced oxidation process without adding external H₂O₂. LaFeO₃ was prepared from Fe(NO₃)₃·9H₂O and La(NO₃)·6H₂O by a simple sol-gel method and its catalytic efficiency was evaluated for mineralization of 4-chlorophenol using a Fenton-like process. The mineralization process was carried out under ultrasonication in presence of heterogeneous LaFeO₃ catalyst with H₂O₂ that was produced during ultrasonication. The mineralization process was monitored through total organic carbon (TOC) analysis. Very importantly, utmost 5-fold synergism was evidenced by the ultrasound mediated LaFeO₃-catalyzed system. Besides, more than twofold synergism was observed by combining the ultrasound assisted LaFeO₃ catalytic process and potassium persulfate (KPS) assisted advanced oxidation process. It is worth to mention that complete mineralization (∼96%) of 4-chlorophenol (initial concentration of 1.25 × 10⁻⁴ M) was observed within 1 h in the presence of LaFeO₃ (0.5 g L⁻¹) and KPS (1.0 mmol) under ultrasonication (40 kHz). Even after four cycles, the activity of LaFeO₃ remained intact which proved its recyclability. Extremely reusable heterogeneous LaFeO₃ catalyst makes the system more interesting from both economic and environmental points of view.     

Effect of reaction temperature on the size and morphology of scorodite synthesized using ultrasound irradiation

Synthesis of scorodite (FeAsO₄·2H₂O) using dynamic action agglomeration and the oxidation effect from ultrasound irradiation was investigated. The effect of different reaction temperatures (90, 70, 50, and 30 °C) on the size and morphology of scorodite particles synthesized under O₂ gas flow and ultrasound irradiation was explored because the generation of fine bubbles depends on the solution temperature. At 90 °C, the size of scorodite particles was non-homogeneous (from fine particles (<1 μm) to large particles (>10 μm)). The oxidation–reduction potential (ORP) and yield at 90 °C showed lower values than those at 70 °C. The scorodite particles, including fine and non-homogeneous particles, were generated by a decrease in the oxidation of Fe(II) to Fe(III) and promotion of dissolution caused by the generation of radicals and jet flow from ultrasound irradiation. Using ultrasound irradiation in the synthesis of scorodite at low temperature (30 °C) resulted in the appearance of scorodite peaks in the X-ray diffraction (XRD) pattern after a reaction time of 3 h. The peaks became more intense with a reaction temperature of 50 °C and crystalline scorodite was obtained. Therefore, ultrasound irradiation can enable the synthesis of scorodite at 30 °C as well as the synthesis of large particles (>10 μm) at higher temperature. Oxide radicals and jet flow generated by ultrasound irradiation contributed significantly to the synthesis and crystal growth of scorodite.     

Structural evolution,growth mechanism and photoluminescence properties of CuWO4 nanocrystals

Copper tungstate (CuWO₄) crystals were synthesized by the sonochemistry (SC) method, and then, heat treated in a conventional furnace at different temperatures for 1 h. The structural evolution, growth mechanism and photoluminescence (PL) properties of these crystals were thoroughly investigated. X-ray diffraction patterns, micro-Raman spectra and Fourier transformed infrared spectra indicated that crystals heat treated and 100 °C and 200 °C have water molecules in their lattice (copper tungstate dihydrate (CuWO₄·2H₂O) with monoclinic structure), when the crystals are calcinated at 300 °C have the presence of two phase (CuWO₄·2H₂O and CuWO₄), while the others heat treated at 400 °C and 500 °C have a single CuWO₄ triclinic structure. Field emission scanning electron microscopy revealed a change in the morphological features of these crystals with the increase of the heat treatment temperature. Transmission electron microscopy (TEM), high resolution-TEM images and selected area electron diffraction were employed to examine the shape, size and structure of these crystals. Ultraviolet–Visible spectra evidenced a decrease of band gap values with the increase of the temperature, which were correlated with the reduction of intermediary energy levels within the band gap. The intense photoluminescence (PL) emission was detected for the sample heat treat at 300 °C for 1 h, which have a mixture of CuWO₄·2H₂O and CuWO₄ phases. Therefore, there is a synergic effect between the intermediary energy levels arising from these two phases during the electronic transitions responsible for PL emissions.     

Preparation via solid-state reaction at room temperature and characterization of layered nanocrystalline NH4MnPO4·H2O

The layered nanocrystalline NH₄MnPO₄·H₂O was obtained by grinding MnSO₄·H₂O and (NH₄)₃PO₄·3H₂O in the presence of surfactant PEG-400 via a solid-state reaction at room temperature, maintaining the mixture at room temperature for 12 h, washing the mixture with water, and drying at 60 °C. The resulting NH₄MnPO₄·H₂O and its products of thermal decomposition were characterized using thermogravimetry and differential thermal analyses (TG/DTA), IR, X-ray powder diffraction (XRD), scanning electron microscopy (SEM), UV–vis, and magnetic susceptibility. The data showed that when dried at 60 °C for 5 h, highly crystallized orthorhombic NH₄MnPO₄·H₂O (space group Pmnm(59)) was obtained with an average particle size of 45 nm and an average interlayer distance of 0.8701 nm. On the other hand, monoclinic nanocrystalline Mn₂P₂O₇ with space group C2/m(12) was obtained when the product was calcined at 600 °C for 3 h. Magnetic susceptibility measurements from room temperature to 2.5 K point to ferrimagnetic ordering at T_N～17 K.     

Sonochemical synthesis of a new nano-sized cerium(III) supramolecular compound; Precursor for nanoceria

Using a sonochemical method, nanoparticles of a new Ce(III) supramolecular compound, (NAMH⁺)₂[Ce₄(pydc)₆(pydcH)₂(H₂O)₈]·8H₂O (1), (H₂pydc = 2,6-pyridinedicarboxylic acid, NAM = nicotinamide), have been synthesized. Compound 1 was characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRPD), FT-IR spectroscopy and elemental analyses, and its structure was determined by X-ray crystallography. It has been revealed that its structure consists of tetra-nuclear building units that extend to a 3D supramolecular network via non-covalent interactions mainly hydrogen bonding. The thermal stability of complex 1 both for its crystals and nanostructures has been studied by the thermal gravimetric (TG) method and compared with each other. The role of ultrasound irradiation power and the concentration of initial reactants on the size and morphology of the nano-structured complex 1, has been investigated. Ceria nanoparticles were obtained upon the calcination of complex 1 at 800 °C under atmospheric air. Furthermore, the fluorescent properties of complex 1 at room temperature were studied.     

Synthesis of nanoparticles of CoxFe(3−x)O4 by combustion reaction method

Nanocrystalline magnetic particles of Co_xFe_(3−x)O₄, with x ranging from 0.79 to 1.15, has been synthesised by combustion reaction method using iron nitrate Fe(NO₃)₃.9H₂O, cobalt nitrate Co(NO₃)₂·6H₂O, and urea CO(NH₂)₂ as fuel without template and subsequent heat treatment. The process is quite simple and inexpensive since it does not involve intermediate decomposition and/or calcining steps. The maximum reaction temperature ranged from 850 to 1010 °C and combustion lasted less then 30 s for all systems. X-ray diffraction patterns of all systems showed broad peaks consistent with cubic inverse spinel structure of CoFe₂O₄. The absence of extra reflections in the diffraction patterns of as-prepared materials ensures phase purity. The average crystallite sizes determined from the prominent (3 1 1) peak of the diffraction using Scherre's equation and TEM micrographs consisted of ca. 27 nm in spherical morphology. FTIR spectra of the as-prepared material showed traces of organic and metallic salts byproducts. However, when the same material was washed with deionised water the byproducts were rinsed off, resulting in pure materials. Magnetic properties such as saturation magnetisation, remanence magnetisation and coercivity field measured at room temperature were 48 emu/g, 15 emu/g and 900 Oe, respectively.     

Sonochemical synthesis and characterization of new nanostructures cobalt(II) metal-organic complexes derived from the azo-coupling reaction of 4-amino benzoic acid with anthranilic acid,salicylaldehyde and 2-naphtol

Nanostructures of three new cobalt(II) complexes, (CoL₁)·0.5DMF·1.5MeOH (1), [H₂L₁ = 5-(4-Carboxy phenyl azo) anthranilic acid], (Co(L₂)₂)·1.5MeOH (2), [HL₂ = 5-(4-Carboxy phenyl azo) salicylaldehyde] and (Co(L₃)₂)·0.5 DMF·0.5MeOH (3), [HL₃ = 1-(4-Carboxy phenyl azo) 2-naphtol], have been synthesized by the reaction of H₂L₁, HL₂ and HL₃ with Co(OAc)₂·4H₂O through sonochemical process. Calcination of the nano-sized compounds 1–3 yield Co₃O₄ nanoparticles at 450 °C under air atmosphere. These nanostructures were characterized by X-ray powder diffraction (XRD) and Scanning Electron Microscopy (SEM). Thermal stability of compounds 1–3 was studied by thermogravimetric (TG) and differential thermal analyses (DTA).     

Preparation of superparamagnetic magnetite nanoparticles by reverse precipitation method: Contribution of sonochemically generated oxidants

Magnetic iron oxide nanoparticles were successfully prepared by a novel reverse precipitation method with the irradiation of ultrasound. TEM, XRD and SQUID analyses showed that the formed particles were magnetite (Fe₃O₄) with about 10 nm in their diameter. The magnetite nanoparticles exhibited superparamagnetism above 200 K, and the saturation magnetization was 32.8 emu/g at 300 K. The sizes and size distributions could be controlled by the feeding conditions of FeSO₄ · 7H₂O aqueous solution, and slower feeding rate and lower concentration lead to smaller and more uniform magnetite nanoparticles. The mechanisms of sonochemical oxidation were also discussed. The analyses of sonochemically produced oxidants in the presence of various gases suggested that besides sonochemically formed hydrogen peroxide, nitrite and nitrate ions contributed to Fe(II) ion oxidation.     

Estimation of the solubility product of hydrocalumite–hydroxide,a layered double hydroxide with the formula of [Ca2Al(OH)6]OH·nH2O

From aqueous NaOH/Ca(OH)₂/NaAl(OH)₄ mixtures, after allowing short reaction times we observed the precipitation of Ca(OH)₂(s) at lower, and a mixture of Ca(OH)₂(s) and a layered double hydroxide, hydrocalumite (HC) at higher aluminate concentrations. From the maximum aluminate concentration, at which the equilibrium solid phase is still portlandite (i.e., further increase in the aluminate concentration results in HC appearing in the precipitate beside the portlandite), the concentration based solubility products of two polymorphs of HC with the formula of [Ca₂Al(OH)₆]OH·nH₂O (differing in n) has been estimated and was found to be log L_HC=−11.4 at 25 °C and −12.1 at 75 °C, respectively (where L_HC=[Ca²⁺]²[Al(OH)₄⁻][OH⁻]³) and at constant ionic strength (I=1 M NaCl). To the best of our knowledge, this is the first published estimate for the solubility product of hydrocalumite. Additionally, from the composition obtained for NaOH/Ca(OH)₂/NaAl(OH)₄ mother liquors in equilibrium with Ca(OH)₂(s), attempts were made to extract the formation constant of the ion pair CaAl(OH)₄⁺. It was found, that the effects caused by the supposed formation of this solution species are too small to be reliably determined, which allowed an upper estimate for its formation constant, K, to be suggested in the temperature range of 25–75 °C (K<200 and 40 M⁻¹ at 25 and 75 °C, respectively).     

Sonochemical synthesis of Dy2(CO3)3 nanoparticles,Dy(OH)3 nanotubes and their conversion to Dy2O3 nanoparticles

Dysprosium carbonates nanoparticles were synthesized by the reaction of dysprosium acetate and NaHCO₃ by a sonochemical method. Dysprosium oxide nanoparticles with average size about 17 nm were prepared from calcination of Dy₂(CO₃)₃·1.7H₂O nanoparticles. Dy(OH)₃ nanotubes were synthesized by sonication of Dy(OAC)₃·6H₂O and N₂H₄. The as-synthesized nanostructures were characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and Fourier transform infrared spectroscopy (FT-IR). Photoluminescence measurement shows that the nanoparticles have two emission peaks around 17,540 cm^?1 and 20,700 cm^?1, which should come from the electron transition from ⁴F_9/2 → ⁶H_15/2 levels and ⁴F_9/2 → ⁶H_13/2 levels, respectively. The effect of calcination temperature and sonication time was investigated on the morphology and particle size of the products. The sizes could be controlled by the feeding rate of the precipitating agent (NaHCO₃ and N₂H₄) and slower feeding rate lead to smaller nanoparticles.     

Obtaining Ca(H2PO4)2·H2O,monocalcium phosphate monohydrate,via monetite from brushite by using sonication

Brushite was synthesized by precipitation of calcium chloride (CaCl₂) and sodium phosphate monobasic (Na₂HPO₄) dried in vacuum and monetite was obtained from this brushite by sonication with a frequency of 90 kHz at 500 W for 90 min. Monetite itself was also transformed in Ca(H₂PO₄)₂·H₂O, monocalcium phosphate monohydrate (MCPM), by sonication with a frequency of 90 kHz at 500 W for 60 min followed by lyophilization. The MCPM was sonicated and lyophilized by three times more until reach over 240 min, but any other phase transformation was observed. All these phase transformations were analyzed by X-ray diffraction (XRD) and infrared spectroscopy (FTIR). Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicated a grain size of about 200 nm in all the samples. The morphology observed was a corn-flake-like grain for brushite, a pseudo-needle-like grains for monetite, and lamellar-like grains for MCPM.     

Proton conductivity of Al(H2PO4)3–H3PO4 composites at intermediate temperature

Composites of Al(H₂PO₄)₃ and H₃PO₄ were synthesised by soft chemical methods with different Al/P ratios. The Al(H₂PO₄)₃ obtained was found to have a hexagonal symmetry with parameter a = 13.687(3)Å, c = 9.1328(1)Å. The conductivity of this material was measured by a.c. impedance spectroscopy between 100 °C and 200 °C in different atmospheres. The conductivity of pure Al(H₂PO₄)₃ in air is in the order of 10^? 6–10^? 7 S/cm between 100 and 200 °C. For samples containing small excess of H₃PO₄, much higher conductivity was observed. The impedance responses of the composites were found to be similar with AlH₂P₃O₁₀·nH₂O under different relative humidity. The conductivity of Al(H₂PO₄)₃–H₃PO₄ composite with Al/P = 1/3.5 reached 6.6 mS/cm at 200 °C in wet 5% H₂. The extra acid is found to play a key role in enhancing the conductivity of Al(H₂PO₄)₃–H₃PO₄ composite at the surface region of the Al(H₂PO₄)₃ in a core shell type behaviour. 0.7% excess of H₃PO₄ can increase the conductivity by three orders of magnitude. These composites might be alternative electrolytes for intermediate temperature fuel cells and other electrochemical devices. Conductivity (9.5 mS/cm) changed little, when the sample was held at 175 °C for over 100 h as the conductivity stabilised.     

Electrical conductivity of fully densified nano CaZr0.90In0.10O3 − δ ceramics prepared by a water-based gel precipitation method

Water-based gel precipitation method was first applied to synthesize high purity nano CaZr_0.90In_0.10O_3 ? δ powders suitable for fabricating dense ceramics at lower temperature. By using CaCO₃, Zr(NO₃)₄ and In(NO₃)₃ as raw materials, PEG as dispersant, CaZr_0.90In_0.10O_3 ? δ with an average particle size of about 40 nm was obtained at 850 °C, which was nearly 350 °C lower than that of traditional solid-state reaction method. Fully densified ceramics with an average grain size of 200–300 nm were obtained at 1350 °C, a temperature about 250 °C lower than that of traditional sintering techniques. Experimental results showed that the flexure stress, total, bulk and grain boundary protonic conductivities of the ceramics were more favorable than those of the ceramics fabricated at 1500 °C and 1600 °C from the powders synthesized by solid-state reaction method.     

Synthesis and characterisation of nanohydroxyapatite using an ultrasound assisted method

Nanostructured hydroxyapatite (HAP) was prepared by a wet precipitation method using Ca(NO₃) and KH₂PO₄ as the main material and NH₃ as the precipitator under ultrasonic irradiation. The Ca/P ratio was set at 1.67 and the pH maintained at a minimum of 9. The temperature conditions and ultrasound influences were investigated using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FT-IR). The results showed that Nano-HAP can be obtained by this method and the particles were achieved to around 30 nm.     

Facile synthesis of calcium silicate hydrate using sodium dodecyl sulfate as a surfactant assisted by ultrasonic irradiation

Calcium silicate hydrate (CSH) consisting of nanosheets has been successfully synthesized assisted by a tip ultrasonic irradiation (UI) method using calcium nitrate (Ca(NO₃)·4H₂O), sodium silicate (Na₂SiO₃·9H₂O) and sodium dodecyl sulfate (SDS) in water. Systematic studies found that reaction time of ultrasonic irradiation and concentrations of surfactant (SDS) in the system were important factors to control the crystallite size and morphologies. The products were characterized by X-ray power diffraction (XRD), field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectrometry (FTIR). The size–strain plot (SSP) method was used to study the individual contributions of crystallite sizes and lattice strain on the peak broadening of the CSH. These characterization techniques revealed the successful formation of a crystalline phase with an average crystallite size of about 13 nm and nanosheet morphology at a reaction time of 10 min UI with 0.2 g SDS in solvent which were found to be optimum time and concentrations of SDS for the synthesis of CSH powders.     

Ultrasound-induced emulsification of subcritical carbon dioxide/water with and without surfactant as a strategy for enhanced mass transport

Pulsed ultrasound was used to disperse a biphasic mixture of CO₂/H₂O in a 1 dm³ high-pressure reactor at 30 °C/80 bar. A view cell positioned in-line with the sonic vessel allowed observation of a turbid emulsion which lasted approximately 30 min after ceasing sonication. Within the ultrasound reactor, simultaneous CO₂-continuous and H₂O-continuous environments were identified. The hydrolysis of benzoyl chloride was employed to show that at similar power intensities, comparable initial rates (1.6 ± 0.3 × 10^–3 s^–1 at 95 W cm^–2) were obtained with those reported for a 87 cm³ reactor (1.8 ± 0.2 × 10^–3 s^–1 at 105 W cm^–2), demonstrating the conservation of the physical effects of ultrasound in high-pressure systems (emulsification induced by the action of acoustic forces near an interface). A comparison of benzoyl chloride hydrolysis rates and benzaldehyde mass transport relative to the non-sonicated, ‘silent’ cases confirmed that the application of ultrasound achieved reaction rates which were over 200 times faster, by reducing the mass transport resistance between CO₂ and H₂O. The versatility of the system was further demonstrated by ultrasound-induced hydrolysis in the presence of the polysorbate surfactant, Tween, which formed a more uniform CO₂/H₂O emulsion that significantly increased benzoyl chloride hydrolysis rates. Finally, pulse rate was employed as a means of slowing down the rate of hydrolysis, further illustrating how ultrasound can be used as a valuable tool for controlling reactions in CO₂/H₂O solvent mixtures.     

Facile synthesis of nanostructured CuO for low temperature NO2 sensing

Detection of environmental pollutant and health hazardous, nitrogen dioxide (NO₂) is reported using nanostructured CuO particulates (NPs). Powder X-ray diffraction and field emission scanning electron microscopy were used to probe crystalline phase and morphological details, respectively. Small crystallites of ∼10–12 nm and a strain of 4% were found in the leafy structure of CuO. Raman studies further supported the presence of nanosized CuO phase. This is the first instance of utilizing CuO NPs to detect 5 ppm of NO₂ even at a low operating temperature of 50 °C. The highest sensitivity for NO₂ was observed at 150 °C, for the first time, in CuO NPs. A low activation energy of 0.18 eV was found for sensing process. The CuO NPs sensor responded to NO₂ within a few seconds and recovered totally under a minute. The kinetics of the NO₂ gas adsorption on the CuO film surface was described following the Elovich model.     

Hydrothermal growth and characterization of La(OH)3 nanorods and nanocables with Ni(OH)2 coating

La(OH)₃/Ni(OH)₂ nanocables and La(OH)₃ nanorods were synthesized by the reaction of KOH with La(NO₃)₃ and Ni(NO₃)₂ at 180 °C under a hydrothermal conditions. X-ray diffraction, transmission electron microscopy and thermal analyses indicated that the nanocable consists of La(OH)₃ core and Ni(OH)₂ outer shell. The diameters of the La(OH)₃ nanorods range from 20 to 30 nm and the lengths range from 150 to 1000 nm. The thickness of the Ni(OH)₂ coating ranges from 10 to 20 nm. The formation mechanism of the nanocables is discussed.     

Mechanistic study on ultrasound assisted pretreatment of sugarcane bagasse using metal salt with hydrogen peroxide for bioethanol production

This study presents the ultrasound assisted pretreatment of sugarcane bagasse (SCB) using metal salt with hydrogen peroxide for bioethanol production. Among the different metal salts used, maximum holocellulose recovery and delignification were achieved with ultrasound assisted titanium dioxide (TiO₂) pretreatment (UATP) system. At optimum conditions (1% H₂O₂, 4 g SCB dosage, 60 min sonication time, 2:100 M ratio of metal salt and H₂O₂, 75 °C, 50% ultrasound amplitude and 70% ultrasound duty cycle), 94.98 ± 1.11% holocellulose recovery and 78.72 ± 0.86% delignification were observed. The pretreated SCB was subjected to dilute acid hydrolysis using 0.25% H₂SO₄ and maximum xylose, glucose and arabinose concentration obtained were 10.94 ± 0.35 g/L, 14.86 ± 0.12 g/L and 2.52 ± 0.27 g/L, respectively. The inhibitors production was found to be very less (0.93 ± 0.11 g/L furfural and 0.76 ± 0.62 g/L acetic acid) and the maximum theoretical yield of glucose and hemicellulose conversion attained were 85.8% and 77%, respectively. The fermentation was carried out using Saccharomyces cerevisiae and at the end of 72 h, 0.468 g bioethanol/g holocellulose was achieved. Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) analysis of pretreated SCB was made and its morphology was studied using scanning electron microscopy (SEM). The compounds formed during the pretreatment were identified using gas chromatography–mass spectrometry (GC–MS) analysis.