Improved adsorption performance of nanostructured composite by ultrasonic wave: Optimization through response surface methodology,isotherm and kinetic studies

In this work, ultrasound-assisted adsorption of an anionic dye, sunset yellow (SY) and cationic dyes, malachite green (MG), methylene blue (MB) and their ternary dye solutions onto Cu@ Mn-ZnS-NPs-AC from water aqueous was optimized by response surface methodology (RSM) using the central composite design (CCD). The adsorbent was characterized using Field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDX) and EDX mapping images. The effects of various parameters such as pH, sonication time, adsorbent mass and initial concentrations of SY, MG and MB were examined. A total 33 experiments were conducted to establish a quadratic model. Cu@ Mn-ZnS-NPs-AC has the maximum adsorption efficiency (>99.5%) when the pH, sonication time, adsorbent mass and initial concentrations of SY, MG and MB were optimally set as 6.0, 5 min, 0.02 g, 9, 12 and 12 mg L⁻¹, respectively. Sonication time has a statistically significant effect on the selected responses. Langmuir isotherm model was found to be best fitted to adsorption and adsorption capacities were 67.5 mg g⁻¹ for SY, 74.6 mg g⁻¹ for MG and 72.9 mg g⁻¹ for MB. Four kinetic models (pseudo-first order, pseudo-second order, Weber–Morris intraparticle diffusion rate and Elovich) were tested to correlate the experimental data and the sorption was fitted well with the pseudo-second order kinetic model.     

Exposure to indoor radon and natural gamma radiation in public workplaces in north-western Greece

Measurements of indoor radon levels and gamma dose rates were performed in 42 workplaces in Ioannina, north-western Greece. Radon concentrations followed a log-normal distribution with an arithmetic mean of 95 ± 51 Bq m^?3. In all cases, radon levels were below 400 Bq m^?3, which is the action level implemented by the Greek Regulation for Radiation Protection, in accordance with the European Commission recommendation. Comparing summer and winter measurements, no statistically significant seasonal variation was established. However, radon concentrations measured in basement and ground floor workplaces were significantly higher (p < 0.01) than those measured in the first and upper floors. Annual effective dose rates from inhalation of radon and its decay products were estimated to be in the range from 0.13 to 1.36 mSv y^?1 with a mean value of 0.62 mSv y^?1. Indoor exposure to natural gamma radiation entailed an average effective dose rate of 0.13 mSv y^?1, of which approximately 62% was due to terrestrial and the rest due to cosmic sources. The reported data contribute to the assessment of radon distribution and dose estimate at the national level.     

Ultrasonically assisted removal of Congo Red,Phloxine B and Fast green FCF in ternary mixture using novel nanocomposite following their simultaneous analysis by derivative spectrophotometry

In this study dependency of simultaneous adsorption of Congo Red (CR), Phloxine B (BP) and Fast green FCF (FG) onto CuS/ZnS nanocomposites loaded on activated carbon (CuS/ZnS-NCs-AC) to pH, adsorbent mass, sonication time and initial dyes concentration were modeled and optimized, while CuS/ZnS-NCs-AC was identified by XRD, FESEM and EDS analysis. CR, PB and FG concentration determination were undertaken by first and second order derivative spectrophotometry in ternary mixture. According to central composite design (CCD) based on desirability function (DF), the best experimental conditions was set as pH 6.0, 0.02 g CuS/ZnS-NCs-AC, 5 min sonication time, 15 mg L⁻¹ for PB and 10 mg L⁻¹ for other dyes. Conduction of experiments to above conditions lead to highest dyes removal efficiency of 99.72, 98.8 and 98.17 for CR, PB and FG, respectively. The adsorption data efficiently fitted by Langmuir isotherm model, while the order of maximum adsorption capacity (Q_max) for PB (128.21 mg g⁻¹) > CR (88.57 mg g⁻¹) > FG (73.40 mg g⁻¹) is related to their different structure and charges. Kinetics of process was efficiently explained according to pseudo-second-order kinetic in cooperation of Weber and Morris based on intraparticle diffusion.     

Application of ZnO nanorods loaded on activated carbon for ultrasonic assisted dyes removal: Experimental design and derivative spectrophotometry method

A method based on application of ZnO nanorods loaded on activated carbon (ZnO-NRs-AC) for adsorption of Bromocresol Green (BCG) and Eosin Y (EY) accelerated by ultrasound was described. The present material was synthesized under ultrasound assisted wet-chemical method and subsequently was characterized by FE-SEM, TEM, BET and XRD analysis. The extent of contribution of conventional variables like pH (2.0–10.0), BCG concentration (4–20 mg L⁻¹), EY concentration (3–23 mg L⁻¹), adsorbent dosage (0.01–0.03 g), sonication time (1–5 min) and centrifuge time (2–6 min) as main and interaction part were investigated by central composite design under response surface methodology. Analysis of variance (ANOVA) was adapted to experimental data and guide the best operational conditions mass by set at 6.0, 9 mg L⁻¹, 10 mg L⁻¹, 0.02 g, 4 and 4 min for pH, BCG concentration, EY concentration, adsorbent dosage, sonication and centrifuge time, respectively. At these specified conditions dye adsorption efficiency was higher than 99.5%. The suitability and well prediction of optimum point was tested by conducting five experiments and respective results revel that RSD% was lower than 3% and high quality of fitting was confirmed by t-test. The experimental data were best fitted in Langmuir isotherm equation and the removal followed pseudo second order kinetics. The experimentally obtained maximum adsorption capacities were estimated as 57.80 and 61.73 mg g⁻¹ of ZnO-NRs-AC for BCG and EY respectively from binary dye solutions. The mechanism of removal was explained by boundary layer diffusion via intraparticle diffusion.     

Optimization of simultaneous ultrasound assisted toxic dyes adsorption conditions from single and multi-components using central composite design: Application of derivative spectrophotometry and evaluation of the kinetics and isotherms

Present study is devoted on the efficient application of Sn (O, S)-NPs -AC for simultaneous sonicated accelerated adsorption of some dyes from single and multi-components systems. Sn (O, S) nanoparticles characterization by FESEM, EDX, EDX mapping and XRD revel its nano size structure with high purity of good crystallinity. Present adsorbent due to its nano spherical shape particles with approximate diameter of 40–60 nm seems to be highly effective in this regard. The effects of five variables viz. pH (3.5–9.5), 0.010–0.028 g of adsorbent and 0.5–6.5 min mixing by sonication is good and practical conditions for well and expected adsorption of MB and CV over concentration range of 3–15 mg L⁻¹. Combination of response surface methodology (RSM) based on central composite design (CCD) and subsequent of analysis of variance (ANOVA) and t-test statistics were used to test the significance of the independent variables and their interactions. Regression analysis reveal that experimental data with high repeatability and efficiency well represented by second-order polynomial model with coefficient of determination value of 0.9988 and 0.9976 for MB and CV, respectively following conditions like pH 8.0, 0.016 g adsorbent, 15 mg L⁻¹ of both dyes 4 min sonication time is proportional with achievement of experimental removal percentage of 99.80% of MB and 99.87% of CV in batch experiment. Evaluation and estimation of adsorption data with Langmuir and Freundlich isotherm well justify the results based on their correlation coefficient and error analysis confirm that Langmuir model is good model with adsorption capacity of 109.17 and 115.34 mg g⁻¹ in single system and 95.69 and 102.99 mg g⁻¹ in binary system for MB and CV, respectively. MB and CV kinetic and rate of adsorption well fitted by pseudo-second order equation both in single and binary systems and experimental results denote more and favorable adsorption of CV than respective value in single system. The pseudo-second-order rate constant k₂ in binary system larger than single system.     

A study on the ignition characteristics for dust explosion of industrial wastes

Paying attention to accidents related to recycling, the authors investigated factors related to the dust explosions. The minimum explosive concentrations were 30–40 g/m³ (polyurethane and plastic dusts) and 70 g/m³ (toner); the explosibility was reduced by about 40% when combustible gas (cyclopentane) existed together with the dust; ignition temperature of a dust cloud was around 500 °C; and the minimum ignition energy was about 11 mJ (polyurethane). Ignition energy was the minimum when the spark duration was about 0.2 ms or more; the explosion probability was the maximum when the spark gap was 5–10 mm; and the ignition energy was the minimum when the electrode tip angle was around 30 °C (polyurethane). From these findings, the dusts produced in the recycling process can be easily evaluated so as to know whether dust explosion is likely to occur.     

Preparation and electrochemical properties of mesoporous Co3O4 crater-like microspheres as supercapacitor electrode materials

Mesoporous Co₃O₄ microspheres with unique crater-like morphology were obtained by utilizing the mesoporous silica material MCM-41 as a template. The analysis results of N₂ adsorption–desorption measurement indicate that the product has a large Brunauer–Emmett–Teller (BET) surface area of 60 m² g⁻¹ and a narrow pore size distribution centering around 3.7 nm. Its electrochemical properties were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements. The findings reveal that this novel morphology material has a smaller inner resistance of about 0.4 Ω and a higher onset frequency of 550 Hz. This material can provide a high specific capacitance of 102 F g⁻¹ and a large capacity retention of 74% in 500 continuous cycles test at a sweep rate of 3 mV s⁻¹. More significantly, the mass loading of electroactive species can reach as large as 2 mg cm⁻², which is one order of magnitude larger than common amount used.     

Ultrasonic enhancement of the simultaneous removal of quaternary toxic organic dyes by CuO nanoparticles loaded on activated carbon: Central composite design,kinetic and isotherm study

Copper oxide nanoparticles loaded on activated carbon (CuO-NPs-AC) were prepared and fully analyzed and characterized with FE-SEM, XRD and FT-IR. Subsequently, this novel material was used for simultaneous ultrasound-assisted adsorption of brilliant green (BG), auramine O (AO), methylene blue (MB) and eosin yellow (EY) dyes. Problems regard to dyes spectra overlap in quaternary solution of this dyes were omitted by derivative spectrophotometric method. The best pH in quaternary system was studied by using one at a time method to achieved maximum dyes removal percentage. Subsequently, sonication time, adsorbent dosage and initial dyes concentrations influence on dyes removal was optimized by central composite design (CCD) combined with desirability function approach (DFA). Desirability score of 0.978 show optimum conditions set at sonication time (4.2 min), adsorbent mass (0.029 g), initial dyes concentration (4.5 mg L⁻¹). Under this optimum condition the removal percentage for MB, AO, EY and BG dyes 97.58, 94.66, 96.22 and 94.93, respectively. The adsorption rate well fitted by pseudo second-order while adsorption capacity according to the Langmuir model as best equilibrium isotherm model for BG, MB, AO and EY was 20.48, 21.26, 22.34 and 21.29 mg g⁻¹, respectively.     

Soil radioactivity levels and radiation hazard assessment in the highlands of northern Jordan

Determination of the natural radioactivity has been carried out, by means of gamma-ray spectrometry system, in surface soil samples collected from various geological formations in urban areas of the northern highlands of Jordan. These highlands, extending from Yarmouk River in the north to Wadi Wala in the south, form the agriculturally important regions of Jordan. Soils of the study region, at which about 70% of the total population of the country are living, mainly originated from limestones that are locally used in construction materials, making the evaluation of environmental radioactivity and estimating the current radiation hazards to the population an interesting issue. The total average concentrations of radionuclides ²²⁶Ra, ²³⁸U, ²³²Th, and ⁴⁰K were 42.5, 49.9, 26.7, and 291.1 Bq kg⁻¹, respectively. Correlations made among these radionuclides prove the existence of secular equilibrium in the investigated soils. The total average absorbed dose rate in the study areas is found to be 51.5 nGy h⁻¹, whereas the annual effective dose equivalent has an average value of 63.2 μSv y⁻¹. The external and internal hazard indices, the radium equivalent activity, and the annual gonadal dose equivalent associated with the investigated soils do not exceed the permissible limits except for soils originated from phosphate rocks. Moreover, the radio-elemental concentrations of uranium, thorium and potassium, evaluated for the various geological features in the study areas were calculated to indicate whether relative depletion/enrichment of radioisotopes had occurred. The results of the present study were discussed and compared with internationally recommended values.     

Synthesis and characterization of ZnS:Ni-NPs loaded on AC derived from apple tree wood and their applicability for the ultrasound assisted comparative adsorption of cationic dyes based on the experimental design

The applicability of ZnS:Ni nanoparticles loaded on activated carbon derived from apple tree wood (ZnS:Ni-NPs-ACATW) for the adsorption of Methylene Blue (MB) and Janus Green B (JGB) dyes in single system from water solution has been described. The synthesized adsorbent characterized and identified by UV–Vis, FE-SEM, EDX, TEM, FTIR and XRD. The influences of operation parameters including initial MB or JGB concentration (9.0–33.0 mg L⁻¹), pH (4.0–10.0), extent of adsorbent (0.08–0.12 g) and sonication time (4.0–8.0 min) investigated and subsequently best operational condition optimized by central composite design (CCD) combined with response surface methodology (RSM) and desirability function (DF) using STATISTICA 10.0 software. At optimum conditions, maximum MB and JSB adsorption onto ZnS:Ni-NPs-ACATW, i.e. 99.57% ± 1.34 and 98.70% ± 2.01, respectively was achieved pH of 7.0, 0.11 g adsorbent, 14 and 28 mg L⁻¹ of MB and JSB concentration respectively and 8 min sonication time. Experimental data were modelled by Langmuir, Freundlich, Temkin and Dubinin-Radushkevich (D-R) isotherms. Langmuir isotherm and monolayer adsorption capacity of MB and JSB was found to be 21.79 and 28.01 mg g⁻¹ respectively. The regression results strongly support more contribution of pseudo-second-order model for more accurate and repeatable representation of kinetic data. These results reveal that ZnS:Ni-NPs-ACATW could be useful as agents to efficiently remove dyes (JGB and MB) from contaminated water and can be very well recommended for wastewater remediation and control of environmental pollution.     

Thermoluminescence,photoluminescence and EPR studies on Mn2+ activated yttrium aluminate (YAlO3) perovskite

Thermoluminescence (TL) measurements were carried out on undoped and Mn²⁺ doped (0.1 mol%) yttrium aluminate (YAlO₃) nanopowders using gamma irradiation in the dose range 1–5 kGy. These phosphors have been prepared at furnace temperatures as low as 400 °C by using the combustion route. Powder X-ray diffraction confirms the orthorhombic phase. SEM micrographs show that the powders are spherical in shape, porous with fused state and the size of the particles appeared to be in the range 50–150 nm. Electron Paramagnetic Resonance (EPR) studies reveal that Mn ions occupy the yttrium site and the valency of manganese remains as Mn²⁺. The photoluminescence spectrum shows a typical orange-to-red emission at 595 nm and suggests that Mn²⁺ ions are in strong crystalline environment. It is observed that TL intensity increases with gamma dose in both undoped and Mn doped samples. Four shouldered TL peaks at 126, 240, 288 and 350 °C along with relatively resolved glow peak at 180 °C were observed in undoped sample. However, the Mn doped samples show a shouldered peak at 115 °C along with two well defined peaks at ～215 and 275 °C. It is observed that TL glow peaks were shifted in Mn doped samples. The kinetic parameters namely activation energy (E), order of kinetics (b), frequency factor (s) of undoped, and Mn doped samples were determined at different gamma doses using the Chens glow peak shape method and the results are discussed in detail.     

Adsorption of naphthalene onto sonicated talc from aqueous solutions

The adsorption behavior of naphthalene onto naturally hydrophobic talc from aqueous solution was investigated in this study. The natural talc was first pretreated by sonication to improve the surface characteristics and enhance the uptake capacity by increasing the specific surface area (SSA) of talc. The naphthalene uptake of talc was found as 276 mg g^?1 and increased to 359 mg g^?1 after the sonication. Adsorption studies also showed that the adsorption of naphthalene onto the sonicated talc was not affected by changes in pH suggesting that the main driving forces for naphthalene adsorption onto talc was hydrophobic bonding rather than electrostatic force. The pseudo-first and pseudo-second orders and intraparticle diffusion equation were used to evaluate the kinetic data and the constants were determined. Adsorption process of naphthalene onto talc followed the pseudo-second-order rate expression for different initial naphthalene concentrations. The Langmuir and Freundlich isotherm models were used to model the isotherm data for their applicability. The Freundlich isotherm best fitted for the adsorption of naphthalene onto talc.     

Radiological impacts of natural radioactivity from phosphogypsum piles in Huelva (Spain)

The activity concentrations of ²²⁶Ra, ²³²Th and ⁴⁰K have been measured by gamma spectroscopy in samples of soil collected from the different zones of around Huelva (Spain). The average activity concentrations of ²²⁶Ra (Bq kg^?1) in the active phosphogypsum (PG) stacks, unrestored and restored zones were 647, 573 and 83 respectively. The corresponding values for ²³²Th and ⁴⁰K (Bq kg^?1) were 8, 10 and 25 and 33, 47 and 225 respectively. As a measure of radiation hazard to the occupational workers and public, the Ra equivalent activities, representative level index and dose rates due to natural radionuclides at 1 m above the ground surface were estimated. The average of absorbed dose rates due to ²²⁶Ra, ²³²Th and ⁴⁰K (nGy/h) from active PG stacks, unrestored and restored zones are 284, 255 and 55.The calculated external γ-radiation average dose (mSv/y) received by the workers of the phosphogypsum piles are estimated to be 0.293, 0.262 and 0.057 which is far below the international agreed dose limit of 20 mSv/y (ICRP-60, 1990) for workers. Also, the radiation dose to a member of the public resulting from the use of PG is negligible compared to the average annual effective dose from natural sources (2.4 mSv/y).     

Highly efficient simultaneous ultrasonic-assisted adsorption of Pb(II), Cd(II), Ni(II) and Cu (II) ions from aqueous solutions by graphene oxide modified with 2,2′-dipyridylamine: Central composite design optimization

In present work, a graphene oxide chemically modified with 2,2′-dipyridylamine (GO-DPA), was synthesized by simple, fast and low-cost process for the simultaneous adsorption of four toxic heavy metals, Pb(II), Cd(II), Ni(II) and Cu(II), from aqueous solutions. The synthesized adsorbent was characterized by FT-IR, XRD, XPS, SEM and AFM measurements. The effects of variables such as pH solution, initial ion concentrations, adsorbent dosage and sonicating time were investigated on adsorption efficiency by rotatable central composite design. The optimum conditions, specified as 8 mg of adsorbent, 20 mg L⁻¹ of each ion at pH 5 and short time of 4 min led to the achievement of a high adsorption capacities. Ultrasonic power had important role in shortening the adsorption time of ions by enhancing the dispersion of adsorbent in solution. The adsorption kinetic studies and equilibrium isotherms for evaluating the mechanism of adsorption process showed a good fit to the pseudo-second order and Langmuir model, respectively. The maximum adsorption capacities (Q_m) of this adsorbent were 369.749, 257.201, 180.893 and 358.824 mg g⁻¹ for lead, cadmium, nickel and copper ions, respectively. The removal performance of adsorbent on the real wastewater samples also showed the feasibility of adsorbent for applying in industrial purposes.     

Dephenolization,dearomatization and detoxification of olive mill wastewater with sonication combined with additives and radical scavengers

In this study, the effects of some additives [manganese (III) oxide (Mn₃O₄), Cu⁺², Fe⁰ and potassium iodate (KIO₃)] and some radical scavengers [sodium carbonate (Na₂CO₃), perfluorohexane (C₆F₁₄) and t-butyl alcohol (C₄H₁₀O)] on the sonication of olive mill effluent wastewater (OMW) were investigated since the wastewaters of this industry are removed with low efficiencies. The maximum total phenol and total aromatic amines (TAAs) removal efficiencies were 88% and 79%, respectively, at 60 °C with only 150 min sonication. The maximum phenol removal was found as 98% with 19 mg L⁻¹ perfluorohexane and 5 mg L⁻¹ Fe⁰ while the maximum TAAs removal was 99% with 16 mg L⁻¹ KIO₃. Catechol, tyrosol, quercetin, caffeic acid, 4-methyl catechol, 2-phenylphenol (2-PHE) and 3-phenyl phenol (3-PHE) were detected as phenol intermediates while trimethlyaniline, aniline, o-toluidine, o-anisidine, dimethylaniline, ethylbenzene and durene were identified as TAAs in the OMW. The maximum acute toxicity removals were 96% and 99% in Vibrio fischeri and Daphnia magna, respectively. Total phenol, TAAs and the toxicity in an OMW were removed efficiently and cost-effectively through sonication.     

Rapid and high-capacity ultrasonic assisted adsorption of ternary toxic anionic dyes onto MOF-5-activated carbon: Artificial neural networks,partial least squares,desirability function and isotherm and kinetic study

The present paper focused on the ultrasonic assisted simultaneous removal of fast green (FG), eosin Y (EY) and quinine yellow (QY) from aqueous media following using MOF-5 as a metal organic framework and activated carbon hybrid (AC-MOF-5). The structure and morphology of AC-MOF-5 was identified by SEM, FTIR and XRD analysis. The interactive and main effects of variables such as pH, initial dyes concentration (mg L⁻¹), adsorbent dosage (mg) and sonication time (min) on removal percentage were studied by central composite design (CCD), subsequent desirability function (DF) permit to achieved real variable experimental condition. Optimized values were found 7.06, 5.68, 7.59 and 5.04 mg L⁻¹, 0.02 g and 2.55 min for pH, FG, EY and QY concentration, adsorbent dosage and sonication time, respectively. Under this conditions removal percentage were obtained 98.1%, 98.1% and 91.91% for FG, EY and QY, respectively. Two models, namely partial least squares (PLS) and multi-layer artificial neural network (ANN) model were used for building up to construct an empirical model to predict the dyes under study removal behavior. The obtained results show that ANN and PLS model is a powerful tool for prediction of under-study dyes adsorption by AC-MOF-5. The evaluation and estimation of equilibrium data from traditional isotherm models display that the Langmuir model indicated the best fit to the equilibrium data with maximum adsorption capacity of 21.230, 20.242 and 18.621 mg g⁻¹, for FG, EY and QY, respectively, while the adsorption rate efficiently follows the pseudo-second-order model.     

Determination of terrestrial gamma, 238U, 232Th and 40K in soil along fracture zones

²³⁸U, ²³²Th and ⁴⁰K concentrations in 72 soil samples from two major fault systems (North and East Anatolian Active Fault Sytems) in Turkey have been studied. However, terrestrial gamma radiation dose originated by natural radionuclides in soil was measured and compared with other measurements in literature for different countries. This extensive survey regarding U, Th and K radionuclide and terrestrial gamma dose measurement was carried out by means of NaI(TI) gamma spectroscopic system and a dose rate meter, respectively. The mean concentration of ²³⁸U, ²³²Th and ⁴⁰K in soil samples in NAFS is higher than determined in EAFS. The measured and calculated mean gamma dose rates in two fault systems are found to be higher than 57 nGyh⁻¹.     

Sonochemical preparation of SbSeI gel

A novel sonochemical method for direct preparation of nanocrystalline antimony selenoiodide (SbSeI) has been established. The SbSeI gel was synthesized using elemental Sb, Se, and I in the presence of ethanol under ultrasonic irradiation (35 kHz, 2 W/cm²) at 50 °C for 2 h. The product was characterized by using techniques such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and optical diffuse reflection spectroscopy (DRS). The SEM and HRTEM investigations exhibit that the as-prepared samples are made up of large quantity nanowires with lateral dimensions of about 20–50 nm and lengths reaching up to several micrometers and single crystalline in nature.     

Synergistic effects of combining ultrasound with the Fenton process in the degradation of Reactive Blue 19

The decoloration of reactive dye C.I. Reactive Blue 19 (RB 19) using combined ultrasound with the Fenton process has been investigated. The effect of varying the concentrations of hydrogen peroxide and iron sulfate, initial pH, ultrasonic power, initial dye concentration and dissolved gas on the decoloration and degradation efficiencies was measured. Calibration of the ultrasound systems was performed using calorimetric measurements and oxidative species monitoring using the Fricke dosimeter and degradations were carried out with a 20 kHz probe type transducer at 2, 4, 6 and 8 W cm⁻² of acoustic intensity at 15, 25, 50 and 75 mg L⁻¹ initial dye concentrations. First order rate kinetics was observed. It was found that while the degradation rate due to ultrasound alone was slow, sonication significantly accelerated the Fenton reaction. While the results were similar to those reported for other dyes, the effects occurred at lower concentrations. The rate and extent of decoloration of RB 19 increased with rising hydrogen peroxide concentration, ultrasonic powers and iron sulfate concentration but decreased with increasing dye concentration. An optimum pH value of pH = 3.5 was found. The rate of decoloration was higher when dissolved oxygen was present as compared with nitrogen and argon confirming the solution phase mechanism of the degradation.     

Ultrasonically assisted hydrothermal synthesis of activated carbon–HKUST-1-MOF hybrid for efficient simultaneous ultrasound-assisted removal of ternary organic dyes and antibacterial investigation: Taguchi optimization

Activated carbon (AC) composite with HKUST-1 metal organic framework (AC–HKUST-1 MOF) was prepared by ultrasonically assisted hydrothermal method and characterized by FTIR, SEM and XRD analysis and laterally was applied for the simultaneous ultrasound-assisted removal of crystal violet (CV), disulfine blue (DSB) and quinoline yellow (QY) dyes in their ternary solution. In addition, this material, was screened in vitro for their antibacterial actively against Methicillin-resistant Staphylococcus aureus (MRSA) and Pseudomonas aeruginosa (PAO1) bacteria. In dyes removal process, the effects of important variables such as initial concentration of dyes, adsorbent mass, pH and sonication time on adsorption process optimized by Taguchi approach. Optimum values of 4, 0.02 g, 4 min, 10 mg L⁻¹ were obtained for pH, AC–HKUST-1 MOF mass, sonication time and the concentration of each dye, respectively. At the optimized condition, the removal percentages of CV, DSB and QY were found to be 99.76%, 91.10%, and 90.75%, respectively, with desirability of 0.989. Kinetics of adsorption processes follow pseudo-second-order model. The Langmuir model as best method with high applicability for representation of experimental data, while maximum mono layer adsorption capacity for CV, DSB and QY on AC–HKUST-1 estimated to be 133.33, 129.87 and 65.37 mg g⁻¹ which significantly were higher than HKUST-1 as sole material with Q_m to equate 59.45, 57.14 and 38.80 mg g⁻¹, respectively.