Generation of tunable and narrow linewidth continuous-wave yellow laser by sum–frequency mixing of diode-pumped solid-state Nd:YAG ring lasers

We report a tunable, narrow linewidth and high beam quality continuous-wave (CW) yellow laser system at 589 nm. The system is an all solid-state design employing single-pass sum–frequency generation in a KTP crystal by mixing the 1064 nm with 1319 nm lines of two side-pumped Nd:YAG enforcing unidirectional ring lasers. With this method, a CW yellow laser at 589.159 nm with an output power of 0.8 W, a linewidth less than 1.5 GHz and a beam quality M² = 1.29 is obtained. The wavelength of the laser also can be precisely tuned from 589.112 to 589.181 nm in step-length of about 0.22 pm.     

Comparison of the higher diffraction order images in methyl-red-doped liquid crystal films

We investigate the change of higher diffraction order images in holographic image storage and reconstruction process. In experiments, an s-polarized Ar⁺ laser (488.0 nm) was used to record permanent grating in the dye-doped liquid crystal, 4,4′-n-entylcyanobiphenyl (5CB) doped with 1 wt% methyl-red (MR), at a small incident angle. Higher diffraction order images were observed when the signal beam was focused in front of and behind the film. Then the film was illuminated by an s-polarized He–Ne laser (632.8 nm) in the direction perpendicular to the surface. The higher diffraction order images were reconstructed. A theory about the change of higher diffraction order images is developed, which is in good agreement with experimental results. The results show that the higher diffraction order provides a useful method for optical information processing.     

Electrical and optical characteristics of a Si-doped (Al)GaInAs digital alloy/AlInAs-distributed Bragg mirrors on InP

We report electrical and optical characteristics of a Si-doped (Al)GaInAs digital alloy/AlInAs Bragg mirror lattice matched to InP grown by molecular beam epitaxy. A 98.2% reflectivity with a 107 nm stop band width centred at 1.54 μ m is obtained. An average voltage drop of 16 mV per period at a current density of 1 KA cm ^− 2is observed for a mean electron concentration of about 5.5  ×  10¹⁸cm ^− 3. The influence of structural and intrinsic properties of the heterostructure on the electrical resistivity and optical reflectivity is analysed.     

Synthesis of Ag-deionized water nanofluids using multi-beam laser ablation in liquids

Multi-pulse laser ablation of silver in deionized water was studied. The laser beams were arranged in a cross-beam configuration. In our experiments, two single-mode, Q-switched Nd-Yag lasers operating at 1064 nm, pulse duration of 5.5 ns and 10 Hz rep rate were used. The laser fluence of the second beam was 0.265 J/cm² for all tests. Two levels of the laser fluences were used for the ablating beam: 0.09 and 0.265 J/cm² (11,014 and 33,042 J/cm² at the focal point, respectively). The silver target was at 50 mm from the cell window and 10 mm deep. The second beam was aligned parallelly with the silver target and focused at 2 mm in front of the focal point of the ablating beam. For all cases, the delay time between the ablating beam and the cross-beam was 40 μs. In general, the ablated particles were almost all spherical. For fluence of 0.09 J/cm ² and single-beam approach, the mean particle size was about 29 nm. The majority of the particles, however, were in 19–35 nm range and there were some big ones as large as 50–60 nm in size. For double-beam approach, the particles were smaller with the average size of about 18 nm and the majority of the particles were in 9–21 nm range with few big one as large as 40 nm. For the beam fluence of 0.265 J/cm² and single-beam configuration, the particle sizes were smaller, the mean particles size was about 18 nm and the majority of the particles were in the range of 10–22 nm with some big one as large as 40 nm. For double-beam approach, the mean particle size was larger (24.2 nm) and the majority of the particle were distributed from 14 to 35 nm with some big particles can be found with sizes as big as 70 nm. Preliminary measurements of the thermal conductivity and viscosity of the produced samples showed that the thermal conductivity increased about 3–5% and the viscosity increased 3.7% above the base fluid viscosity even with the particle volume concentration as low as 0.01%.     

Synthesis,characterization and magnetic properties of lightly doped La2−xSrxCuO4 (x = 0.04) nanoparticles

Lightly doped La_2−xSr_xCuO₄ (x = 0.04) nanoparticles with different particle sizes have been successfully prepared by a sol–gel method and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), infrared transmission (IR) spectra and superconducting quantum interference device (SQUID) magnetometer. All samples are single phase and have an orthorhombic unit cell. As the particle size reduces, it is found that the IR band at around 685 cm⁻¹ corresponding to the in-plane Cu–O asymmetrical stretching mode shifts to higher frequency and the magnetization exhibits a large enhancement at low temperature. The magnetic susceptibility of all samples follows a modulated Curie law between ∼20 K and ∼100 K and the Curie constant displays a strong dependence on the particle size. It is suggested that as the particle size decreases surface effects should play an important role in the magnetic properties of the nanoparticles.     

Diffraction patterns and nonlinear optical properties of gold nanoparticles

Stable gold nanoparticles have been prepared by using soluble starch as both the reducing and stabilizing agents; this reaction was carried out at 40 °C for 5 h. The obtained gold nanoparticles were characterized by UV–Vis absorption spectroscopy, transmission electron microscopy (TEM) and z-scan technique. The size of these nanoparticles was found to be in the range of 12–22 nm as analyzed using transmission electron micrographs. The optical properties of gold nanoparticles have been measured showing the surface plasmon resonance. The second-order nonlinear optical (NLO) properties were investigated by using a continuous-wave (CW) He–Ne laser beam with a wavelength of 632.8 nm at three different incident intensities by means of single beam techniques. The nonlinear refractive indices of gold nanoparticles were obtained from close aperture z-scan in order of 10^?7 cm²/W. Then, they were compared with diffraction patterns observed in far-field. The nonlinear absorption of these nanoparticles was obtained from open aperture z-scan technique. The values of nonlinear absorption coefficient are obtained in order of 10^?1 cm/W.     

Thermodynamics and kinetics of CO and benzene adsorption on Pt(111) studied with pulsed molecular beams and microcalorimetry

The adsorption and desorption of the system CO/Pt(111) and C₆H₆/Pt(111) at 300 K has been investigated with a pulsed molecular beam method in combination with a microcalorimeter. For benzene the sticking probability has been measured in dependence of the coverage θ. For coverages θ > 0.8 transient adsorption is observed. From an analysis of the time-dependence of the molecular beam pulses the rate constant for desorption is determined to be 5.6 s^? 1. With a precursor-mediated kinetic adsorption model this allows to obtain also the hopping rate constant of 95.5 s^? 1. The measured adsorption enthalpies could be best described by (199 ? 77θ ? 51θ²) kJ/mol, in good agreement with the literature values. For CO on Pt(111) also transient adsorption has been observed for θ > 0.95 at 300 K. The kinetic analysis yields rate constants for desorption and hopping of 20 s^?1 and 51 s^?1, respectively. The heats of adsorption show a linear dependence on coverage (131 ? 38θ) kJ/mol between 0 ≤ θ ≤ 0.3, which is consistent with the desorption data from the literature. For higher coverage (up to θ = 0.9ML) a slope of ?63 kJ/mol describes the decrease of the differential heat of adsorption best. This result is only compatible with desorption experiments, if the pre-exponential factor decreases strongly at higher coverage. We found good agreement with recent quantum chemical calculations made for (θ = 0.5ML).     

Ferromagnetic order and spin-glass behavior in multi-metallic compound Ni1.125Co0.375[Fe(CN)6] · 6.8H2O

Multi-metallic Prussian blue compound Ni_1.125Co_0.375[Fe(CN)₆] · 6.8H₂O has been synthesized. The Mössbauer spectroscopy at room temperature and IR spectra study revealed that the metal ions are bonded through cyanide ligand and the presence of low spin Fe^III(S = 1/2) and high spin Fe^III(S = 5/2) ions, as showed in these structure: Fe^III(S = 1/2)-CN-(Co^II/Ni^II)(96%) and Fe^III(S = 5/2)-NC-(Co^II/Ni^II) (4%). The Curie constant of C = 3.00 cm³ K mol⁻¹ and Weiss paramagnetic Curie temperature of θ = 16.43 K were observed in fitting according to Curie–Weiss law. These results indicate that there existed a ferromagnetic exchange interaction in the complexes. The observed value of coercive field (H_c) and remanent magnetization (M_r) at 4 K for the compound are 497 Oe and 1.03 Nβ. The presence of spin-glass behaviours in the compound is ascribed mainly to domain mobility or domain growth under different cooling conditions.     

Investigation of optimum condition in oxygen gas-assisted laser cutting

Laser cutting characteristics including power level and cutting gas pressure are investigated in order to obtain an optimum kerf width. The kerf width is investigated for a laser power range of 50–170 W and a gas pressure of 1–6 bar for steel and mild steel materials. Variation of sample thickness, material type, gas pressure and laser power on the average cut width and slot quality are investigated. Optimum conditions for the steel and mild steel materials with a thickness range of 1–2 mm are obtained. The optimum condition for the steel cutting results in a minimum average kerf width of 0.2 mm at a laser power of 67 W, cutting rate of 7.1 mm/s and an oxygen pressure of 4 bar. A similar investigation for the mild steel cutting results in a minimum average kerf width of 0.3 mm at the same laser power of 67 W, cutting rate of 9.5 mm/s, and an oxygen pressure of 1 bar. The experimental average kerf is about 0.3 mm, which is approximately equal to the estimated focused beam diameter of 0.27 mm for our focusing lens (f=4 cm and 100 W power). This beam size leads to a laser intensity of about 1.74×10⁹ W/m² at the workpiece surface. The estimated cutting rate from theoretical calculation is about 8.07 mm/s (1.0 mm thickness and 100 W power), which agrees with the experimental results that is 7.1 mm/s for 1.0 mm thickness of mild steel at the laser power of 88 W.     

Spectroscopy and efficient laser emission of Yb3+: LuAG single crystal grown by μ-PD

A LuAG shaped rod crystal, doped with Yb³⁺, has been grown by μ-PD technique. The crystal diameter was about 3 mm and the length around 130 mm. A complete spectroscopic investigation in the temperature range 10–300 K is reported and data has been utilized to model the laser behavior. In the laser experiment the Yb:LuAG sample was placed in an X cavity and pumped longitudinally obtaining an efficient CW laser emission. The Yb:LuAG laser yielded a maximum output power of 23 mW with a slope efficiency of 32% and a threshold around 35 mW, at lasing wavelength of 1030 nm. No significant depolarization effects were observed, indicating a crystal growth with negligible stress. The output beam profile was investigated, yielding M² ≈ 1.0 in both directions, further confirming the good optical quality of the sample.     

Photodiode properties of molecular beam epitaxial InSb on a heavily doped substrate

Photodiodes of InSb were fabricated on an epitaxial layer grown using molecular beam epitaxy (MBE). Thermal cleaning of the InSb (0 0 1) substrate surface, 2° towards the (1 1 1) B plane, was performed to remove the oxide. Photodiode properties of МВЕ-formed epitaxial InSb were demonstrated. Zero-bias resistance area product (R₀A) measurements were taken at 80 K under room temperature background for a pixel size of 100 μm × 100 μm. Values were as high as 4.36 × 10⁴ Ω/cm², and the average value of R₀A was 1.66 × 10⁴ Ω/cm². The peak response was 2.44 (A/W). The epitaxial InSb photodiodes were fabricated using the same process as bulk crystal InSb diodes with the exception of the junction formation method. These values are comparable to the properties of bulk crystal InSb photodiodes.     

Synthesis and electrical properties of nanocrystalline Ca1 − xEuxMnO3 ± δ (0.1 ≤ x ≤ 0.4) powders prepared at low temperature using citrate gel method

Nanopowders of Ca_1 − xEu_xMnO₃ (0.1 ≤ x ≤ 0.4) manganites were synthesized as a single phase using the auto gel-combustion method. The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation or contamination. The Ca_1 − xEu_xMnO₃ system has been synthesized at 800 °C during 18 h, against the conventional method of mixing oxides used to obtain these materials at higher temperatures of synthesis. The formation reaction was monitored by X-ray diffraction (XRD) analysis and an infrared absorption technique (FTIR). The polycrystalline powders are characterised by nanometric particle size, ∼ 48 nm as determined from X-ray line broadening analysis using the Scherrer equation. Morphological analysis of the powders, using the scanning electron microscope (SEM), revealed that all phases are homogeneous and the europium-substituted samples exhibit a significant decrease in the grain size when compared with the undoped samples. The structure refinement by using the Rietveld method indicates that the partial calcium substitution by europium (for x ≥ 0.3) modifies the orthorhombic structure of the CaMnO₃ perovskite towards a monoclinic phase. All manganites show two active IR vibrational modes around 400 and 600 cm^− 1. The high temperature dependence of electrical resistivity (between 25 and 600 °C) allows us to conclude that all the samples exhibit a semiconductor behaviour and the europium causes a decrease in the electrical resistivity by more than one order of magnitude. The results can be well attributed to the Mn⁴⁺/Mn³⁺ ratio.     

Thermal cis–trans isomerization of triazo-benzene

1,3,5-Hydroxy-triazo-benzene (H-TAB) was synthesized through a coupling-oxidation protocol. Temperature-controlled UV, IR, and ab initio calculation were carried out to investigate the cis–trans thermal isomerization of H-TAB. In temperature-controlled UV experiments, λ_max of the π–π¹ band and for the trans conformation at 335 nm and that for the cis form at 282 nm are shifted by increased temperature; band intensities of the π–π¹ transition decrease and λ_max of the π–π¹ band is shifted toward the high-energy region. The maximum peak at 2922 cm⁻¹ is shifted to 2926 cm⁻¹, and that at 2852 cm⁻¹ is shifted to 2856 cm⁻¹ at increased temperature in the temperature-controlled IR experiment. Ab initio calculation reveals that the cis conformation of H-TAB is more stable than the trans form because the cis form has less spatial repulsion. Therefore, the ground-state energy difference induced by steric repulsion of the benzene unit is the driving force of the blue shift in the thermal IR and UV spectra for the triazo-benzene.     

Theoretical study of optoelectronic properties of GaAs1−xBix alloys using valence band anticrossing model

The (12 × 12) and (14 × 14) valence band anticrossing (V-BAC) models were applied to calculate the electronic band structure of GaAs_1−xBi_x dilute alloys along Δ-, Λ- and Σ-directions at room temperature. A comparative study based on these models was performed in terms of energy levels, optical transitions, spin–orbit splitting and effective mass. We found a significant reduction of the band-gap energy E_g by roughly 81 meV/%Bi accompanied by an increase in the spin–orbit splitting Δ_so+ by about 56 meV/%Bi. Furthermore, Δ_so+ does come into resonance with E_g at ∼12%Bi for resonance energy equal to 0.73 eV. An excellent agreement has occurred between the (14 × 14) V-BAC model predictions and experimental results reported in the literature. In addition, we have investigated the Bi composition and k-directions dependence of the effective mass at Γ point. A slight increase of the holes effective mass with x can affect the holes transport properties of GaAsBi. The intrinsic carrier density increases with both x and the temperature T, but it remains below 10¹⁰ cm⁻³ for x ⩽ 5% and T ⩽ 300 K.     

Synchrotron quantification of ultrasound cavitation and bubble dynamics in Al–10Cu melts

Knowledge of the kinetics of gas bubble formation and evolution under cavitation conditions in molten alloys is important for the control casting defects such as porosity and dissolved hydrogen. Using in situ synchrotron X-ray radiography, we studied the dynamic behaviour of ultrasonic cavitation gas bubbles in a molten Al–10 wt% Cu alloy. The size distribution, average radius and growth rate of cavitation gas bubbles were quantified under an acoustic intensity of 800 W/cm² and a maximum acoustic pressure of 4.5 MPa (45 atm). Bubbles exhibited a log-normal size distribution with an average radius of 15.3 ± 0.5 μm. Under applied sonication conditions the growth rate of bubble radius, R(t), followed a power law with a form of R(t) = αt^β, and α = 0.0021 & β = 0.89. The observed tendencies were discussed in relation to bubble growth mechanisms of Al alloy melts.     

Thermoluminescence,infrared reflectivity and electron paramagnetic resonance properties of hemimorphite

Silicate mineral hemimorphite has been investigated concerning its TL, IR and EPR properties. A broad TL peak around 180 °C and a weaker and narrower peak around 360 °C were found in a sample annealed at 600 °C for 1 h and then irradiated. The deconvolution using the CGCD method revealed peaks around 132, 169, 222 and 367 °C. The reflectivity measurements showed several bands in the NIR region due to H₂O, OH and Al–OH complexes. No band was observed in the visible region. The thermal treatments were carried out from ∼110 to 940 °C and dehydration was observed, first causing a diminishing optical absorption in general and the disappearance of water and hydroxyl absorption bands. The EPR spectrum of natural hemimorphite, presented Cu²⁺ signals at g = 2.4 and g = 2.1 plus E₁′ signal superposed to Fe³⁺ signal around g = 2.0.     

InGaAsP/InP photodetectors targeting on 1.06 μm wavelength detection

InP-based InGaAsP photodetectors targeting on 1.06 μm wavelength detection have been grown by gas source molecular beam epitaxy and demonstrated. For the detector with 200 μm mesa diameter, the dark current at 10 mV reverse bias and R₀A are 8.89 pA (2.2 × 10⁻⁸ A/cm²) and 3.9 × 10⁵ Ω cm² at room temperature. The responsivity and detectivity of the InGaAsP detector are 0.30 A/W and 1.45 × 10¹² cm Hz^1/2 W⁻¹ at 1.06 μm wavelength. Comparing to the reference In_0.53Ga_0.47As detector, the dark current of this InGaAsP detector is about 570 times lower and the detectivity is more than ten times higher, which agrees well with the theoretical estimation.     

Nanostructures on GaAs surfaces due to 60 keV Ar+-ion beam sputtering

The effect of 60 keV Ar⁺-ion beam sputtering on the surface topography of p-type GaAs(1 0 0) was investigated by varying angle of incidence of the ion (0–60°) with respect to substrate normal and the ion fluence (2 × 10¹⁷–3 × 10¹⁸ ions/cm²) at an ion flux of 3.75 × 10¹³ ions/cm²-s. For normal incidence and at a fluence of 2 × 10¹⁷ ions/cm², holes and islands are observed with the former having an average size and density of 31 nm and 4.9 × 10⁹ holes/cm², respectively. For 30° and 45° off-normal incidence, in general, a smooth surface appears which is unaffected by increase of fluence. At 60° off-normal incidence dots are observed while for the highest fluence of 3 × 10¹⁸ ions/cm² early stage of ripple formation along with dots is observed with amplitude of 4 nm. The applicability and limitations of the existing theories of ion induced pattern formation to account for the observed surface topographies are discussed.     

Infrared transmission of chalcohalide glasses in the Ge–Se–Te–I system

Infrared (IR) transmission spectra in the range from 4000 to 400 cm^?1 have been measured at ambient temperature for the prepared, (Ge₂₂Se₁₄Te₆₄)_100?xI_x, glasses where x = 0, 4, 6, 8 and 10 at.%. The effects of both iodine content and the annealing of glasses at different temperatures on the transmittance and observed absorption peaks have been evaluated. Scanning electron microscope (SEM) micrographs were performed to insure the effect of annealing on the obtained IR transmission spectra.     

DFT study of carbon monoxide adsorption on α-Al2O3(0001)

The adsorption of CO on α-Al₂O₃(0001) was studied using the DFT-GGA computational method and on α-Al₂O₃ powder experimentally by Infra red spectroscopy. The core and valence level regions of α-Al₂O₃(0001) single crystal surface were also studied experimentally. Ar ions sputtering of the surface results in a slight but reproducible decrease in the XPS O2p lines in the valence band regions due to preferential removal of surface (and near surface) O atoms. Core level XPS O1s and Al2p further confirmed oxygen depletion with an associated surface stoichiometry close to Al₂O_2.9. The adsorption energy of CO was computed and found equal to 0.52 eV for θ = 0.25, it decreased to 0.42 eV at θ = 1. The IR frequency of νCO was also computed and in all cases it was blue shifted with respect to gas phase CO. The shift, Δν, decreased with increasing coverage where it was found equal to 56 cm^? 1 for θ = 0.25 and decreased to 30 cm^? 1 for θ = 1. Structural analyses indicated that the change in the adsorption energy and the associated frequency shift is due to surface relaxation upon adsorption. Experimentally the adsorption of CO gave rise to one main IR peak at 2154 cm^? 1 at 0.3 Torr and above. Two far smaller peaks are also seen at lower pressures of 0.03–0.2 Torr at 2189 and 2178 cm^? 1. The isosteric heat of adsorption was computed for the IR band at 2154 cm^? 1 and was found equal to 0.2 eV which did not change with coverage in the investigated range up to θ = 0.6.