工艺参数对飞秒激光沉积硅基ZnO大面积均匀薄膜性能的影响

研究了衬底温度、真空度、激光能量、激光脉冲频率及退火处理对飞秒激光制备硅基ZnO大面积均匀薄膜的结构和性能的影响.结果表明,当激光能量为1.5mJ、脉冲频率为400 Hz、真空度为1.0 mPa、衬底温度为80℃时,所制备的薄膜质量最佳.薄膜呈高度c-轴取向,为典型的六方纤锌矿结构,晶粒沿垂直于衬底表面的方向生长;当衬底温度高于80℃时,随着温度的升高,c-轴取向度降低.80℃制备的薄膜在可见紫外区域透过率达98;,电阻率随温度升高而减小,退火后薄膜的透过率增大、电阻率升高.     

热壁外延制备InAs/Si(211)薄膜及其电学性能研究

采用热壁外延(Hot Wall Epitaxy,HWE)沉积系统在单晶Si(211)衬底表面制备了InAs薄膜,研究了不同生长温度(300℃、350℃、400℃、450℃和500℃)对薄膜材料结构及其电学性能的影响.通过X射线衍射(XRD)、扫描电子显微镜(SEM)、原子力显微镜(AFM)、霍尔(Hall)测试等,对InAs/Si(211)薄膜的晶体结构、表面形貌及电学参数进行了测试分析.结果表明:采用HWE技术在Si(211)衬底表面成功制备了InAs薄膜,薄膜具有闪锌矿结构并沿(111)方向择优生长.随着生长温度从300℃升高到500℃,全峰半高宽(FWHM)先减小后增大,生长温度为400℃时薄膜的晶粒尺寸最大为73.4 nm,载流子浓度达到1022 cm-3,霍尔迁移率数值约为102 cm2/(V·s),说明优化生长温度能够降低InAs薄膜的缺陷复合,使薄膜结晶质量和电学性能得到提高.SEM及AFM的测试结果显示由于较高的晶格失配及Si衬底斜切面(211)的特殊取向,在Si(211)衬底上生长的InAs薄膜主要为三维层加岛状(S-K)生长模式,表面粗糙度(Ra)随温度的升高先减小后增大,400℃时薄膜的平均表面粗糙度Ra为48.37 nm.     

衬底温度对共蒸发制备GaSb多晶薄膜性质的影响

采用共蒸发的方法在玻璃衬底上制备出GaSb多晶薄膜材料.研究了薄膜生长速率与衬底温度、Ga源温度和Sb源温度的关系.通过XRD、UV-Vis、Hall效应和AFM等测试方法,研究了衬底温度对于GaSb薄膜的结构特性、光电性质以及表面形貌的影响.GaSb多晶薄膜具有(111)择优取向,薄膜的吸收系数达到105 cm-1,晶粒尺寸随衬底温度升高逐渐增大;衬底温度为540℃时,薄膜的迁移率达到127 cm2/V·s,空穴浓度为3×1017 cm-3.GaSb薄膜的表面粗糙度随温度增加而增加.     

Ge覆盖层诱导晶化多晶Si薄膜的晶化特性研究

采用电子束蒸发技术在衬底温度为180℃条件下生长具有Ge覆盖层的非晶Si薄膜,并于500℃、600℃、700℃真空退火5h.采用Raman散射、X射线衍射(XRD)、全自动数字式显微镜等对所制备薄膜的晶化特性进行研究.结果表明,Ge覆盖层具有诱导非晶Si薄膜晶化的作用,且随着退火温度的升高a-Si薄膜晶化越显著.具有Ge覆盖层非晶薄膜经500℃退火5h沿Si(400)方向开始晶化,对应晶粒尺寸约为4.9 nm.将退火温度升高到700℃时,非晶硅薄膜几乎全部晶化,晶化多晶Si薄膜在Si(400)方向表现出很强的择优取向特性,晶粒尺寸高达23.3μm.与相同条件下制备的无Ge覆盖层的非晶Si薄膜相比,晶化温度降低了300℃.     

基于直流磁控溅射室温制备ZnO薄膜研究

采用直流磁控溅射法在P型<100>晶向单晶硅衬底上室温制备ZnO薄膜,对室温制备的ZnO薄膜分别在500℃、600℃、700℃进行高温退火,通过采用X射线衍射(XRD)、拉曼光谱和场发射扫描电子显微镜(SEM)、HP4145B型半导体参数测试仪分析不同退火温度对室温生长ZnO薄膜微结构、表面形貌和,Ⅰ-Ⅴ特性影响.实验结果表明,室温生长的ZnO薄膜为非晶态,随退火温度增加,ZnO薄膜出现(002)、(100)、(101)晶面衍射峰且逐渐增强,晶粒大小相对增加,在700℃退火后,呈高度c轴择优取向,晶粒间界明显,拉曼光谱E2模增强.     

衬底温度对电子束蒸发ZnS薄膜结构和光学特性的影响

采用电子束蒸发法在不同衬底温度下,150℃、200℃、250℃和300℃,制备了ZnS薄膜;用X射线衍射仪、原子力显微镜、膜厚仪和紫外-可见光-近红外分光光度计分别表征ZnS薄膜的晶体结构、表面形貌和光学特性;并分析了不同衬底温度对薄膜的结构和光学特性的影响.结果表明:在硅衬底上制备的ZnS都为多晶薄膜,具有闪锌矿β-ZnS结构;随衬底温度升高呈(111)晶面高度择优取向,平均晶粒尺寸有所增大,内应力、位错密度、折射率和吸收系数有所减小,禁带宽度随之增大;衬底温度为300℃时制备的薄膜表面均匀致密,呈现较优的结构和光学性能.     

退火温度对Co掺杂CeO2稀磁氧化物薄膜的结构和铁磁性能的影响

采用溶胶-凝胶法,在Si(100)和石英玻璃衬底上制备了3;Co掺杂CeO2稀磁氧化物薄膜,研究了不同退火温度(500 ℃, 600 ℃和700 ℃)对薄膜结构和铁磁性能的影响.XRD 和拉曼光谱结果表明,随着退火温度的升高,薄膜晶化度明显提高.不同退火温度下的3;Co掺杂CeO2薄膜为多晶薄膜,且未破坏CeO2原有的结构.随着退火温度的升高, 晶粒尺寸逐渐增大.另外,3;Co掺杂CeO2薄膜在可见光范围内都有很好的透射率,其室温下的光学带隙Eg随退火温度增加而减小.超导量子干涉磁强计(SQUID)测量表明所有样品都表现出室温铁磁性,随着退火温度的升高,饱和磁化强度和矫顽力增大,700 ℃退火的薄膜具有最大的饱和磁化强度和最大的矫顽力.不同退火温度导致样品的磁性有了明显的变化,这源于磁性产生的不同机理.可见薄膜的结构最终影响了其铁磁性能.     

衬底温度对Ba2FeMoO6薄膜生长的影响及磁性质研究

利用自制的Ba2 FeMoO6陶瓷靶材,采用脉冲激光沉积技术,在钛酸锶SrTiO3 (100)衬底上,于衬底温度分别为700℃、800℃、900℃下制备出了厚度为100 nm的双钙钛矿型氧化物Ba2 FeMoO6薄膜.分别采用XRD、AFM和VSM表征了样品的结构、表面形貌和磁性质.结果表明,在衬底温度为900℃时沿c轴择优取向生长效果最佳、成膜质量最好,从生长过程角度解释了原因;样品M-H曲线表明在衬底温度不同时生长出的各样品均具有铁磁性,其磁性随衬底温度的升高而增加,分子饱和磁矩在700℃到800℃时变化显著,在800℃到900℃时变化不是很大.     

衬底温度对含硅量子点的SiCx薄膜结构及其光学特性的影响

采用磁控共溅射沉积法,以Si靶和SiC靶为靶材,单晶Si(100)和石英为衬底,在不同衬底温度下沉积了富硅SiCx薄膜.在氮气氛下于1100 ℃退火,得到包含硅量子点的SiCx薄膜.采用傅立叶变换红外吸收光谱、拉曼光谱、掠入射X射线衍射和吸收谱对退火后的SiCx薄膜进行了表征.结果表明:当衬底温度从室温(25℃)升至300℃时,薄膜的晶化率增至71.3;,硅量子点尺寸增至8.9 nm,而光学带隙则减至2.42 eV;随着衬底温度进一步升高,薄膜的晶化率降至63.1;,硅量子点尺寸减小至7.3 nm,而光学带隙却增加至2.57 eV;当衬底温度从室温(25℃)升至400℃时,薄膜的吸收系数呈先增大后减小趋势.在本实验条件下,最佳衬底温度为300℃.     

热退火对电子束蒸镀方法制备的ZnO:Al薄膜光电性质的影响

采用电子束蒸镀方法在Si(100)衬底上沉积了ZnO:Al(ZAO)薄膜.在氧气气氛下对ZnO:Al薄膜进行了退火处理,退火温度的范围为400～800℃.X射线衍射(XRD)图样表明所制备的ZnO:Al薄膜具有六方结构,为c轴(002)择优取向的多晶薄膜.用Van der Pauw法测量了ZAO薄膜的电学特性,结果显示其电导率在500℃达到最大值.测量了ZAO薄膜的室温微区光致发光和变温发光光谱,观测到了ZnO自由激子、束缚在中性施主中心(D0)上的束缚激子以及束缚在离化施主中心(D+0)上的束缚激子发射.     

CsI-LiCl共晶材料的坩埚下降法生长与闪烁性能研究

本文采用坩埚下降法,在真空密封的石英坩埚中成功生长出CsI-LiCl与CsI-LiCl:Na共晶闪烁体。通过扫描电子显微镜(SEM)观察晶体微结构表明该共晶中LiCl相与CsI相存在周期性的层状排列,CsI相的厚度在5 μm左右。共晶样品的X射线激发发射谱显示在CsI-LiCl和CsI-LiCl:Na共晶样品存在缺陷发光,在CsI-LiCl样品中还观察到了纯CsI的自陷激子(STE)发光。CsI-LiCl样品在α粒子激发下的多道能谱中观察到明显的全能峰,这一结果证明CsI-LiCl共晶可用于热中子探测的潜力。     

静电纺丝法制备CeO2微纳米纤维及其除氟性能

以聚丙烯腈(PAN)为载体,六水合硝酸铈[Ce(NO₃)₃·6H₂O]为原料,采用静电纺丝法制备了Ce(NO₃)₃/PAN纤维,在空气中热处理得到CeO₂微纳米纤维,通过XRD、BET和SEM对CeO₂微纳米纤维进行表征。采用静态吸附实验探讨了CeO₂微纳米纤维去除水溶液中氟离子的性能,考察了溶液pH值、初始氟离子浓度及共存阴离子等对吸附性能的影响。结果表明,pH=3时,CeO₂微纳米纤维对F^-的吸附性能最佳,CeO₂吸附量随着F^-浓度的增大呈上升趋势。CeO₂微纳米纤维对F^-的吸附等温线遵循Langmuir模型,二级动力学模型能很好地描述CeO₂微纳米纤维对F^-的吸附过程。CeO₂微纳米纤维的除氟性能优良,可为其实际应用提供理论参考。     

Crystal structures of the cis and trans isomers of a tetrathia[3.3.3.3]cyclophane

Both the cis and trans isomers of 3,11,18,26-tetrathiatricyclo[26.2.2.1^5,9.2^13,16.1^20,24] hexatriaconta-5,7,9,20,22,24-hexene have been prepared and structurally characterized. Each of these centrosymmetric tetrathia dimers includes two cyclohexane rings in chair conformations with either 1,4-cis or 1,4-trans bonding and two meta-substituted benzene rings. The cis isomer packs into the monoclinic space group P2₁/a with a = 10.485(3)Å, b = 10.3956(18)Å, c = 14.1343(10)Å, = 105.200(13)°, Z = 2 and refined to an R factor of 0.046. The trans isomer crystallizes in the monoclinic space group P2₁/c with a = 10.7217(12)Å, b = 5.6797(7)Å, c = 25.415(5)Å, = 96.001(12)°, Z = 2 and refined to an R factor of 0.043. In the cis structure each benzene ring faces a cyclohexane ring while in the trans structure the cyclohexane rings face one another.     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

电沉积法制备ZnO纳米棒阵列及其发光特性

本文以掺F的SnO2导电玻璃为基板,以硝酸锌水溶液为电解液,采用三电极恒电位体系电沉积制备ZnO纳米棒阵列,系统考察了硝酸锌浓度和沉积电位等工艺参数对ZnO纳米棒阵列的微观形貌及其发光性能的影响规律.结果表明,硝酸锌浓度和沉积电位对纳米棒阵列的形貌有显著影响,控制适宜的工艺条件可以制备出直径分布均匀、结晶性好且纯度高的六方纤锌矿ZnO纳米棒阵列.荧光光谱分析表明,电沉积制备出的ZnO纳米棒阵列在385 nm附近有一个强荧光发射峰,且发光性能稳定、对纳米棒阵列微观形貌的细微变化不敏感,使其在发光二极管和激光器等领域具有广阔的应用前景.     

Phase Properties of Hexanedioldiacrylate/E7 Blends

Abstract

Equilibrium phase diagrams of uncured and UV-cured difunctional hexanedioldiacrylate and the eutectic mixture of low molecular weight liquid crystals E7 are established by polarized optical microscopy and differential scanning calorimetry. Data are analyzed using the Maier-Saupe model of nematic order. In the case of the uncured system the Flory-Huggins free energy of isotropic mixing is applied while for the cured system, the Flory-Rehner elastic free energy model is used. A good correlation between experimental and theoretical phase diagrams is found in both systems.     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

C–H...O,C–H...π and π–π stacking interactions in 3-(2,4-dimethylphenyloxymethyl)-3,4-dihydroisocoumarin

3-(2,4-Dimethylphenyloxymethyl)-3,4-dihydroisocoumarin (C₁₈H₁₈O₃) was prepared by the alkylation of o-lithio N-methyl benzamide with 2-(2,4-dimethylphenoxy)methyl oxirane, followed by alkaline hydrolysis. The compound crystallizes in the orthorhombic space group Pbca with unit cell parameters : a = 8.239(2) Å, b = 14.918(5) Å, c = 24.831(9) Å, Z = 8. The crystal structure was solved by direct methods and refined to R = 0.0514 for 1564 observed reflections. The heterocyclic ring adopts a distorted half-chair conformation. Molecules are connected by π–π interactions between phenyl rings of the isocoumarin nucleus forming dimers. Dimers are connected via C–H...O hydrogen bonds forming chains. Further intermolecular C–H...π hydrogen bonds link the dimer chains to form supramolecular structure.     

A new method for the investigation of orientation relationships in meteoritic plessite

The orientation relationship (OR) between the bcc and fcc phase in the plessite microstructure of the iron meteorites Watson, Agpalilik and Gibeon has been analysed in a scanning electron microscope using electron back‐scattered diffraction (EBSD). A very strong OR exists, independently on the analysed plessite type and the observed spreading of single orientation data. The agreement between the experimental orientation distribution and existing models varies for each meteorite. The black plessite in the Agpalilik corresponds to the Nishiyama‐Wassermann model whereas the duplex plessite of the Gibeon meteorite shows an OR close to the Kurdjumov‐Sachs model. The Watson meteorite is strongly deformed so that a general OR is difficult to determine due to the blurred experimental orientation distribution. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

X-ray analysis of sideroxol from <Emphasis Type="Italic">Sideritis leptoclada</Emphasis>

Sideroxol (1), a kaurane diterpene which has the ent-7α,18-dihydroxy-15β,16β-epoxykaurane structure (MW = 320.47, C₂₀H₃₂O₃) was obtained from the acetone extract of Sideritis leptoclada plant as well as from some other Sideritis species. It crystallizes in the orthorhombic space group P2₁, 2₁, 2₁ with a = 10.967(3), b = 24.555(5), c = 6.372(4) Å, Dc = 1.240 g cm⁻³, Z = 4, and refines to R = 0.065 for 721 independent reflections. The skeleton consists of three fused six-membered rings and a five-membered ring with fused epoxide. The six membered rings exhibited slightly distorted chair conformation. In addition to sideroxol, two kaurane and five kaurene diterpenes were isolated from the hexane and acetone extracts of the studied plant.