Matrix‐grafted multiwalled carbon nanotubes/poly(methyl methacrylate) nanocomposites synthesized by in situ RAFT polymerization: A kinetic study

A new approach was developed to functionalize multiwalled carbon nanotubes (MWCNTs) with a polymerizable methyl methacrylate (MMA) groups, and the structure of functionalized MWCNTs were characterized by FTIR, Raman, XPS, and TEM. Using the strategy of “grafting through,” poly(methyl methacrylate) (PMMA) chains were grafted onto the surface of MWCNTs during the in situ synthesis of MWCNT/PMMA nanocomposites over reversible addition‐fragmentation chain transfer (RAFT) polymerization. Kinetics of RAFT‐mediated polymerization of MMA in the presence of MMA‐grafted MWCNTs was studied by using gas chromatography and gel permeation chromatography. To further study, attached polymers were detached and their molecular characteristics were compared to freely formed chains. Results of kinetic studies showed that the utilized commercial chain transfer agent strictly reduced the rate of polymerization as well as relatively controlled molecular weights and narrow molecular weight distributions of free chains. MWCNTs showed a radical activity, retarding the polymerization and reducing the rate of reaction. The effect of MWCNTs concentrations on molecular weights and polydispersity indexes (PDI) was different at the surface and in the bulk. The molecular weights of free chains increased, and the PDI was decreased with increasing MWCNTs. © 2012 Wiley Periodicals, Inc. Int J Chem Kinet 44: 555–569, 2012     

Synthesis of Poly(methyl acrylate) Grafted onto Silica Particles by Z-supported RAFT Polymerization

RAFT polymerization of methyl acrylate (MA) mediated by silica-supported 3-(methoxycarbonyl-phenyl-methylsulfanylthiocarbonylsulfanyl) propionic acid (Si- MPPA) and 3-(benzylsulfanylthiocarbonylsulfanyl) propionic acid (Si-BSPA) was investigated. The molecular weight and polydispersity of grafted polymeric chains and the grafted chain transfer agent (CTA) efficiency (G_e) were strongly dependent on the types and loading of Si-CTAs and free CTA used in solution. Under similar reaction conditions, the graft polymerization mediated by Si-MPPA was better controlled than that using Si-BSPA. The introduction of a free CTA in solution during Si-MPPA mediated polymerization could significantly decrease the polydispersity of free and grafted polymeric chains and enhance the grafted CTA efficiency, and longer polymeric chains could be grafted onto silica support when Si-MPPA with a higher CTA loading was used to mediate the polymerization. In all cases, the RAFT polymerization using 2-(2-cyanopropyl) dithiobenzoate (CPDB) as a free CTA could afford well-defined grafted PMA and significantly increased G_e value, while the polymerization rate was also decreased.     

Macromolecular brushes synthesized by “grafting from” approach based on “click chemistry” and RAFT polymerization

Well‐defined macromolecular brushes with poly(N‐isopropyl acrylamide) (PNIPAM) side chains on random copolymer backbones were synthesized by “grafting from” approach based on click chemistry and reversible addition‐fragmentation chain transfer (RAFT) polymerization. To prepare macromolecular brushes, two linear random copolymers of 2‐(trimethylsilyloxy)ethyl methacrylate (HEMA‐TMS) and methyl methacrylate (MMA) (poly(MMA‐co‐HEMA‐TMS)) were synthesized by atom transfer radical polymerization and were subsequently derivated to azide‐containing polymers. Novel alkyne‐terminated RAFT chain transfer agent (CTA) was grafted to polymer backbones by copper‐catalyzed 1,3‐dipolar cycloaddition (azide‐alkyne click chemistry), and macro‐RAFT CTAs were obtained. PNIPAM side chains were prepared by RAFT polymerization. The macromolecular brushes have well‐defined structures, controlled molecular weights, and molecular weight distributions (M_w/M_n ≦ 1.23). The RAFT polymerization of NIPAM exhibited pseudo‐first‐order kinetics and a linear molecular weight dependence on monomer conversion, and no detectable termination was observed in the polymerization. The macromolecular brushes can self‐assemble into micelles in aqueous solution. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 443–453, 2010     

Preparation of poly(methyl methacrylate) grafted hydroxyapatite nanoparticles via reverse ATRP

Surface-initiated reverse atom transfer radical polymerization (reverse ATRP) technical was successfully employed to modify hydroxyapatite (HAP) nanoparticles with poly(methyl methacrylate) (PMMA). The peroxide initiator moiety for reverse ATRP was covalently attached to the HAP surface through the surface hydroxyl groups. Reverse ATRP of methyl methacrylate (MMA) from the initiator-functionalized HAP was carried out, and the end bromide groups of grafted PMMA initiated ATRP of MMA subsequently. Fourier transformation infrared (FTIR) spectroscopy, thermal gravimetric analysis (TGA) and transmission electron microscopy (TEM) were employed to confirm the grafting and to characterize the nanoparticle structure. The grafted PMMA gave HAP nanoparticles excellent dispersibility in MMA monomer. As the amount of grafted PMMA increased, the dispersibility of surface-grafted HAP and the compressive strength of HAP/PMMA composites were improved.     

Controlled grafting from poly(vinylidene fluoride) films by surface‐initiated reversible addition–fragmentation chain transfer polymerization

A reversible addition–fragmentation chain transfer (RAFT) polymerization technique was applied to graft polymerize brushes of poly(methyl methacrylate) (PMMA) and poly(poly(ethylene glycol) monomethacrylate) (PPEGMA) from poly(vinylidene fluoride) (PVDF) surfaces. PVDF surfaces were exposed to aqueous LiOH, followed by successive reductions with NaBH₄ and DIBAL‐H to obtain hydroxyl functionality. Azo‐functionalities, as surface initiators for grafting, were immobilized on the PVDF surfaces by esterification of 4,4′‐azobis(4‐cyanopentanoic acid) and the surface hydroxyl groups. The chemical composition and surface topography of the graft‐functionalized PVDF surfaces were characterized by X‐ray photoelectron spectroscopy, attenuated total reflectance‐FTIR spectroscopy, and atomic force microscopy. Kinetics studies revealed a linear increase in the graft concentration of PMMA and PPEGMA with the reaction time, indicating that the chain growth from the surface was consistent with a “controlled” or “living” process. The living chain ends were used as the macroinitiator for the synthesis of diblock copolymer brushes. Water contact angles on PVDF films were reduced by surface grafting of PEGMA and MMA. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3071–3082, 2006     

Click chemistry meets polymerization: Controlled incorporation of an easily accessible ruthenium(II) complex into a PMMA backbone via RAFT copolymerization

The copper(I)-catalyzed azide-alkyne cycloaddition provided an easy and efficient access to a functionalized heteroleptic ruthenium(II) complex monomer. A grafted copolymer with the heteroleptic ruthenium(II) complex and methyl methacrylate (MMA) as comonomer was synthesized by reversible addition fragmentation chain transfer (RAFT) polymerization. The product was characterized by means of ¹H NMR spectroscopy, UV/vis spectroscopy and size exclusion chromatography coupled with a photodiode array detector. The RAFT process itself led to a grafted copolymer with a low polydispersity index.     

Synthesis of poly(vinyl acetate) block copolymers by successive RAFT and ATRP with a bromoxanthate iniferter

Poly(vinyl acetate)-b-polystyrene, poly(vinyl acetate)-b-poly(methyl acrylate) and poly(vinyl acetate)-b-poly(methyl methacrylate) block copolymers with low polydispersity (M(w)/M(n) < 1.25) were prepared by successive reversible addition-fragmentation chain transfer (RAFT) polymerization and atom transfer radical polymerization (ATRP) employing a bromoxanthate iniferter (initiator-transfer agent-terminator).     

RAFT‐mediated synthesis of poly[(oligoethylene glycol) methyl ether acrylate] brushes for biological functions

The synthesis of poly[(oligoethylene glycol) methyl ether acrylate] [poly(OEGA)] brushes was achieved via reversible addition‐fragmentation chain transfer (RAFT) polymerization and used to selectively immobilize streptavidin proteins. Initially, gold surfaces were modified with a trithiocarbonate‐based RAFT chain transfer agent (CTA) by using an ester reaction involving a gold substrate modified with 11‐mercapto‐1‐undecanol and bis(2‐butyric acid)trithiocarbonate. poly(OEGA) brushes were then prepared via RAFT‐mediated polymerization from the surface‐immobilized CTA. The immobilization of CTA on the gold surface and the subsequent polymer formation were followed by ellipsometry, X‐ray photoelectron spectroscopy, grazing angle‐Fourier transform infrared spectroscopy, atomic force microscopy, and water contact‐angle measurements. RAFT‐mediated polymerization method gave CTA groups to grafted poly(OEGA) termini, which can be converted to various biofunctional groups. The terminal carboxylic acid groups of poly(OEGA) chains were functionalized with amine‐functionalized biotin units to provide selective attachment points for streptavidin proteins. Fluorescence microscopy measurements confirmed the successful immobilization of streptavidin molecules on the polymer brushes. It is demonstrated that this fabrication method may be successfully applied for specific protein recognition and immobilization. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and Characterization of Poly(methyl methacrylate)-b-Polystyrene/TiO2 Nanocomposites Via Reversible Addition-Fragmentation Chain Transfer Polymerization

A diblock copolymer, poly(methyl methacrylate)-b-polystyrene (PMMA-b-PS), was grafted onto the surface of nano-titania (nano-TiO₂) successfully via reversible addition-fragmentation chain transfer (RAFT) polymerization. The surface of TiO₂ nanoparticles was modified initially by attaching dithioester groups to the surface using silane coupling agent 3-(chloropropyl)triethoxy silane and sodium ethyl xanthate. The polymerization of methyl methacrylate and styrene were then initiated and propagated on the TiO₂ surface by RAFT polymerization. The resulting composite nanoparticles were characterized by means of XPS, FT-IR, ¹H NMR and TGA. The results confirmed the successful grafting of poly(methyl methacrylate) (PMMA) and diblock copolymer chains onto the surface of TiO₂. The amount of PMMA grafted onto the TiO₂ surface increased with the polymerization time. Moreover, the kinetic studies revealed that the ln([M]₀/[M]), where [M]₀ is the initial and [M] is the time dependent monomer concentrations, increased linearly with the polymerization time, indicating the living characteristics of the RAFT polymerization.     

Properties of matrix-grafted multi-walled carbon nanotube/poly(methyl methacrylate) nanocomposites synthesized by in situ reversible addition-fragmentation chain transfer polymerization

Multi-walled carbon nanotubes (MWCNT)/poly(methyl methacrylate) (PMMA) nanocomposites were synthesized by the in situ reversible addition-fragmentation chain transfer (RAFT) polymerization of methyl methacrylate (MMA) in the presence of MWCNTs, at which the bulk polymer was grafted onto the surface of nanotubes through the ??grafting through?? strategy. For this purpose, MWCNTs were formerly functionalized with polymerizable MMA groups. MMA and PMMA-grafted MWCNTs were characterized by Fourier-transform infrared spectroscopy, Raman, X-ray photoelectron spectroscopy, transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). Dissolution of nanotubes was examined in chloroform solvent and studied by UV?Cvis spectroscopy. Thermogravimetric and degradation behavior of prepared nanocomposites was investigated by TGA. MWCNTs had a noticeable boosting effect on the thermal stability of nanocomposites. TGA thermograms showed a two-step weight loss pattern for the degradation of MWCNT-PMMA/PMMA nanocomposites which is contrast with neat PMMA. Introduction of MWCNTs also improved the dynamic mechanical behavior and electrical conductivity of nanocomposites. TEM micrograph of nanocomposite revealed that the applied methods for functionalization of nanotubes and in situ synthesis of nanocomposites were comparatively successful in dispersing the MWCNTs in PMMA matrix.     

Synthesis of graft copolymer by ATRP of MMA from poly(phenylacetylene)

The present report describes the synthesis of a densely grafted copolymer consisting of a rigid main chain and flexible side chains by the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) from an ATRP initiator‐bearing poly(phenylacetylene) [poly(BrPA)]. Poly(BrPA) was obtained by the polymerization of 4‐ethynylbenzyl‐2‐bromoisobutyrate using [Rh(NBD)Cl]₂ in the presence of Et₃N. The ¹H NMR spectrum showed that poly(BrPA) was in the cis‐transoid form. Upon heating at 30 °C for 24 h the cis‐transoid form was maintained. ATRP of MMA from the poly(BrPA) was carried out at 30 °C using CuX (X = Br, Cl) as the catalyst and N,N,N′,N′,N′‐pentamethyldiethylenetriamine as the ligand, and the resulting graft copolymers were investigated with ¹H NMR and SEC. To analyze the graft structure in more detail, the graft copolymers were hydrolyzed with KOH and the resultant poly(MMA) part was investigated with ¹H NMR and SEC. The polydispersity indexes of 1.25–1.45 indicated that the graft copolymers have well‐controlled side chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6697–6707, 2006     

Effect of chain transfer agent on the radiation grafting of methyl methacrylate onto chromium(III) crosslinked collagen

Thioglycolic acid is an efficient agent for controlling the lengths of poly(methyl methacrylate) (PMMA) chains grafted onto collagen. The addition of 0.006 mol of thioglycolic acid per one mol of methyl methacrylate (MMA) has no effect on the yield of grafting, but brings about a decrease in the molecular weight of grafted PMMA by about 50%. The mechanism of the grafting reaction in the presence of the chain transfer agent thioglycolic acid is discussed on the basis of the results.     

High density cationic polymer brushes from combined “click chemistry” and RAFT‐mediated polymerization

A simple method for preparing cationic poly[(ar‐vinylbenzyl)trimethylammonium chloride)] [poly(VBTAC)] brushes was used by combined technology of “click chemistry” and reversible addition‐fragmentation chain transfer (RAFT) polymerization. Initially, silicon surfaces were modified with RAFT chain transfer agent by using a click reaction involving an azide‐modified silicon wafer and alkyne‐terminated 4‐cyanopentanoic acid dithiobenzoate (CPAD). A series of poly(VBTAC) brushes on silicon surface with different molecular weights, thicknesses, and grafting densities were then synthesized by RAFT‐mediated polymerization from the surface immobilized CPAD. The immobilization of CPAD on the silicon wafer and the subsequent polymer formation were characterized by X‐ray photoelectron spectroscopy, water contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, atomic force microscopy, and ellipsometry analysis. The addition of free CPAD was required for the formation of well‐defined polymer brushes, which subsequently resulted in the presence of free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. In addition, by varying the polymerization time, we were able to obtain poly(VBTAC) brushes with grafting density up to 0.78 chains/nm² with homogeneous distributions of apparent needle‐like structures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermo- and pH-responsive polypropylene microporous membrane prepared by the photoinduced RAFT-mediated graft copolymerization

Thermo- and pH-responsive polypropylene microporous membrane prepared by photoinduced reversible addition–fragmentation chain transfer (RAFT) graft copolymerization of acrylic acid and N-isopropyl acrylamide by using dibenzyltrithiocarbonate as a RAFT agent. Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR), X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FE-SEM) were used to characterize the structural and morphological changes on the membrane surface. Results of ATR/FT-IR and XPS clearly indicated that poly(acrylic acid) (PAAc) and poly(N-isopropyl acrylamide) (PNIPAAm) were successfully grafted onto the membrane surface. The grafting chain length of PAAc on the membrane surface increased with the increase of UV irradiation time, and decreased with the increase of the concentration of chain transfer agent. The PAAc grafted membranes containing macro-chain transfer agents, or the living membrane surfaces were further functionalized via surface-initiated block copolymerization with N-isopropyl acrylamide in the presence of free radical initiator, 2,2′-azobisisobutyronitrile. It was found that PNIPAAm can be grafted onto the PAAc grafted membrane surface. The results demonstrated that polymerization of AAc and NIPAAm by the RAFT method could be accomplished under UV irradiation and the process possessing the living character. The PPMMs with PAAc and PNIPAAm grafting chains exhibited both pH- and temperature-dependent permeability to aqueous media.     

Synthesis of poly(methyl acrylate) loops grafted onto silica nanoparticles via reversible addition‐fragmentation chain transfer polymerization

Reversible addition‐fragmentation chain transfer (RAFT) polymerization was used to produce poly(methyl acrylate) (pMA) loops grafted onto silica nanoparticles using doubly anchored bifunctional RAFT agents 1,4‐bis(3′‐trimethoxysilylpropyltrithiocarbonylmethyl)benzene (Z‐group approach) and 1,6‐bis(o,p‐2′‐trimethoxysilylethylbenzyltrithiocarbonyl)hexane (R‐group approach) as mediators. In both cases, molecular weights of the resulting surface‐confined polymer loops increased with monomer conversion, whereas the grafting density was significantly higher in the case of the R‐group supported RAFT polymerization due to mechanistic differences of the RAFT process at the surface. This result was evident from thermogravimetric analysis and supported by scanning electron microscopy. Polymer loops with molecular weights up to 53,000 g mol^?1 were accessible with polydispersities of about 2.0 without and 1.5 with the addition of free RAFT agent. UV signals of the detached pMA loops measured via size exclusion chromatography were shifted to higher molecular weights compared with the corresponding RI signals, indicating branching reactions caused by the close proximity of growing radicals and polymer at the surface of the silica nanoparticles. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7656–7666, 2008     

β-CD存在下MMA细乳液体系的RAFT聚合

近年来，活性自由基聚合已成为高分子合成领域中的一个热门课题．Rizzardo研究小组提出了一种新型活性自由基聚合反应，即RAFT(Reversible addition-fragmentation chain transfer)聚合．RAFT反应在传统的自由基聚合中加入了具有高链转移常数和特定结构的链转移剂——双硫酯类化合物．当链转移剂的浓度足够大时，链转移反应由不可逆变为可逆，聚合反应也随之发生质的变化，由不可控     

Polymer Architectures via Reversible Addition Fragmentation Chain Transfer (RAFT) Polymerization

Various versatile chain transfer agents (CTAs) have been synthesized for reversible addition fragmentation chain transfer (RAFT) polymerzation. Such CTAs have been used to modify hydroxyl containing materials and produce well-controlled molecular architectures such as amphiphilic copolymer from poly (ethylene glycol), AB block copolymer consisting of a biodegradable segment, poly (l-lactic acid) (PLLA) and grafted copolymers of poly (styrene), poly (methyl methacrylate) and poly (methyl acrylate) from cellulose.     

Study on reversible addition-fragmentation chain transfer (RAFT) polymerization of MMA in the presence of 2-cyanoprop-2-yl 1-dithiophenanthrenate (CPDPA)

The RAFT polymerization of methyl methacrylate (MMA) was carried out in the presence of 2-cyanoprop-2-yl 1-dithiophenanthrenate (CPDPA). The results exhibit controlled polymerization characters: well-controlled molecular weight with narrow polydispersity (minimal value: 1.04) molecular weight linearly increasing with conversion and first-order kinetics of polymerization. The resulting polymer can be used to synthesize methyl methacrylate-styrene copolymer with narrow polydispersity. The effect of molar ratio among MMA/CPDPA/AIBN on polymerization was investigated.     

Imparting antifouling properties of poly(2-hydroxyethyl methacrylate) hydrogels by grafting poly(oligoethylene glycol methyl ether acrylate)

The antifouling properties of poly(2-hydroxyethyl methacrylate- co-methyl methacrylate) hydrogels were improved by the surface grafting of a brush of poly(oligoethylene glycol methyl ether acrylate) [poly(OEGA)]. The atom-transfer radical polymerization (ATRP) of OEGA (degree of polymerization = 8) was initiated from the preactivated surface of the hydrogel under mild conditions, thus in water at 25 degrees C. The catalytic system was optimized on the basis of two ligands [1,1,4,7,10,10-hexamethyl-triethylenetetramine (HMTETA) or tris[2-(dimethylamino)ethyl]amine (Me6TREN)] and two copper salts (CuIBr or CuICl). Faster polymerization was observed for the Me 6TREN/CuIBr combination. The chemical composition and morphology of the coated surface were analyzed by X-ray photoelectron spectroscopy, attenuated total reflectance Fourier transform infrared spectroscopy, contact angle measurements by the water droplet and captive bubble methods, scanning electron microscopy, and environmental scanning electron microscopy. The hydrophilicity of the surface increased with the molar mass of the grafted poly(OEGA) chains, and the surface modifications were reported in parallel. The antifouling properties of the coatings were tested by in vitro protein adsorption and cell adhesion tests, with green fluorescent protein, beta-lactamase, and lens epithelial cells, as model proteins and model cells, respectively. The grafted poly(OEGA) brush decreased the nonspecific protein adsorption and imparted high cell repellency to the hydrogel surface.     

Grafting of hyperbranched poly(amidoamine) onto waste tire rubber powder and its potential application as the curing agent for epoxy resin

To realize the high‐valued application of waste tire rubber (WTR), hyperbranched poly(amidoamine) (PAMAM) were synthesized from the surface of WTR powders to endow its chemical reactivity. The hyperbranched PAMAM‐grafted WTR powders containing a large amount of amine groups on their surface were obtained through “divergent procedure.” First, methyl methacrylate‐grafted WTR powders (MMA‐g‐WTR) were prepared by ozone‐induced grafting polymerization. Afterwards, Michael reaction and subsequent amidation reactions were carried out repetitively to obtain hyperbranched PAMAM chains grafted from the surface of the MMA‐g‐WTR powders. The resulting hyperbranched PAMAM‐grafted WTR powders exhibit good dispersibility in water. Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, and thermogravimetric analysis demonstrate the successful grafting of hyperbranched PAMAM on WTR surface. The hyperbranched PAMAM‐grafted WTR powder could be utilize as curing agent and potential toughener for epoxy resin due to abundant amine groups and elastomeric feature of WTR. Differential scanning calorimetry shows that the hyperbranched PAMAM‐grafted WTR powders can be used as effective curing agent for epoxy resin. Copyright © 2011 John Wiley & Sons, Ltd.