Investigations on the Thermal and Elastic Properties of ZnO-Incorporated Phosphate Glasses and Glass Ceramics

Abstract

Glasses of the 45P₂O₅-(40-x)CaO-15Na₂O-xZnO system with increasing zinc oxide (ZnO) concentrations within the ranges of 3 ≤ x ≤ 12 mol% were obtained by employing the melt-quench technique. ZnO inclusions in the phosphate glass network lead to increases in its density and, conversely, a decrease in its molar volume. On the basis of the obtained thermal analysis data, the glasses underwent thermal treatment, which helped to derive their glass ceramic equivalents. The evaluations of structural and elastic properties of glasses before and after thermal treatments were made using X-ray diffraction (XRD) studies and ultrasonic nondestructive testing. The differential thermal analysis data show the reduction in the crystallization tendency and increase in thermal properties, such as crystallization temperature (T _P), thermal stability

(T _c – T _g) (where T_c is crystallization onset temperature and T _g is glass transition temperature), thermal stability parameter (S), and degree of glassification (D _g) of phosphate glasses against the progressive additions of ZnO. The XRD of glass ceramics confirmed the dominance of metaphosphate, pyrophosphate, and ZnO-related crystalline features. The measured elastic moduli, such as longitudinal (L), shear (G), Young's (Y), and bulk (K), and Vicker's microhardness values increased in both glass and glass ceramics with an increase in ZnO incorporation.     

Characterisation of the surface structure and bioactivity of glass and glass ceramics using surface topography

The present paper reports the results of the relationship between the surface topography, microstructure and the in vitro bioactivity of samples with and without fluorapatite content in simulated body fluid. Glasses and glass ceramics belonging to the Li₂O-SiO₂-CaO-P₂O₅-CaF₂ system were prepared by using conventional melting technique following by heat treatment to obtain glass ceramics. This current study demonstrates the benefits of combining two microscopic methods for better investigation of the surface structure. The formation of apatite layer on the surface and the increase in surface roughness proved that the glasses and glass ceramics with bioactive fluorapatite content could satisfy to the requirements for biomaterial applications. The results also showed that the roughness of apatite layer formed after immersion in body fluid on the surface of glasses with fluorapatite was more pronounced than that of equivalent glass ceramic samples cured under the same conditions.      

Preparation of polypyrrole (PPy)-derived polymer/ZrO2 nanocomposites

New polypyrrole (PPy)-derived polymer/ZrO₂ nanocomposite materials are prepared by single-step oxidative polymerization of pyrrole (Py) and/or N-methylpyrrole (mPy) in the presence of HCl-functionalized ZrO₂ nanoparticles and ammonium persulfate. The physicochemical features of the PPy–ZrO₂, poly(Py-co-mPy)–ZrO₂ and PmPy–ZrO₂ hybrids were analyzed by XPS, FTIR, XRD and UV–Vis techniques. To explore the advantages of these nanocomposites for potential applications, their thermal, conductive and electrochemical properties were investigated. The characterization reveals that a chemical bonding, based on electrostatic interactions, is established between the polymers and the ZrO₂ nanoparticles. Interestingly, it is found that the growth of polymer on the surface of Cl-functionalized ZrO₂ becomes more significant as the Py moiety (–NH– species) content in the polymer increases. The thermal stability and conductivity of the polymers increase by hybridization with the ZrO₂ nanoparticles. This is assigned to the affective interaction of the polymers with the ZrO₂ nanoparticles. Particularly, the resulting nanocomposites keep high conductivities, ranging between 0.323 and 0.929 S cm⁻¹. Finally, voltammetric characterization shows that the PPy–ZrO₂ and poly(Py-co-mPy)–ZrO₂ nanocomposites are electroactive, thus demonstrating their capability for electrochemical applications. These results highlight the great influence of the nanoparticle interface and the nature of monomer on the nanocomposite formation and properties.

     

Influence of composition on corroding process of Na<Subscript>2</Subscript>O-K<Subscript>2</Subscript>O-CaO-ZrO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> glasses

The corroding process of six glasses of the Na₂O-K₂O-CaO-ZrO₂-SiO₂ system with ZrO₂content 0–2.13 mass % by water was observed during static tests at 121°C and pressure of 0.25 MPa in steam sterilizer. Significant increase of Na⁺ and K⁺ content in leachates was observed after the addition of ZrO₂ into glass. Further increase of the content of ZrO₂ in glasses slowed down the rate of Na⁺ and K⁺ leaching. The leaching process of SiO₂ as well as Na⁺, K⁺, and Ca²⁺ ions was evaluated on the basis of comparison with model leaching processes. Variation of the concentrations of Na⁺, K⁺, Ca²⁺, and SiO₂ in leachates with time was described by empirical equation. Observed changes in the initial leaching rates of Na⁺, K⁺, Ca²⁺, and SiO₂ can be ascribed to the content of ZrO₂ in glasses. The presence of ZrO₂ in glasses reduced the overall rate of glass dissolution.     

Red luminescence in MgO-GeO<Subscript>2</Subscript> gel glasses and glass ceramics doped with Mn ions prepared by sol-gel method

To obtain red luminants, MgO-GeO₂ gel glasses and glass ceramics doped with manganese ions were prepared by a sol-gel method and their properties were investigated by measuring X-ray diffraction (XRD), electron spin resonance (ESR), and luminescence and excitation spectra. Under UV irradiation at 254 nm, the gel glasses and glass ceramics showed red luminescence at 620–665 nm, the intensity of which became strong with increasing the heat-treatment temperature. A glass ceramic with the composition 1.0MnO-25MgO-75GeO₂ heat treated at 1000°C exhibited the strongest red luminescence at 661 nm. From the results of XRD and ESR, this luminescence is found to be due to the transition from the ⁴T_1g to the ⁶A_1g state of octahedrally coordinated Mn²⁺ ions located in MgGeO₃ polycrystals. The luminescence wavelength of the glass ceramics (∼665 nm) is long compared with Eu³⁺-containing phosphors (612 nm), therefore the glass ceramics can be expected for red luminants.     

Photocatalytic activity of ZrO2 nanoparticles prepared by electrical arc discharge method in water

ZrO₂ nanoparticles were synthesized through arc discharge of zirconium electrodes in deionized (DI) water. X-ray diffraction (XRD) analysis of the as prepared nanoparticles indicates formation a mixture of nanocrystalline ZrO₂ monoclinic and tetragonal phase structures. Transmission electron microscopy (TEM) images illustrate spherical ZrO₂ nanoparticles with 7–30 nm diameter range, which were formed during the discharge process with 10 A arc current. The average particle size was found to increase with the increasing arc current. X-ray photoelectron spectroscopy (XPS) analysis confirms formation of ZrO₂ at the surface of the nanoparticles. Surface area of the sample prepared at 10 A arc current, measured by BET analysis, was 44 m²/g. Photodegradation of Rhodamine B (Rh. B) shows that the prepared samples at lower currents have a higher photocatalytic activity due to larger surface area and smaller particle size.     

The Non-Isothermal Devitrification of Potassium Germanate Glasses

The devitrification behaviour of the glasses K₂O·xGeO₂ with x=4, 7 or 8 was examined by means of differential thermal analysis (DTA), the Fourier transformation infrared (FTIR) transmittance spectra and X-ray diffraction (XRD). The glass transition temperatures were related to the molar ratio GeO₄/GeO₆. For the glass with x=4, metastable K₄Ge₉O₂₀> crystals are initially formed and then converted at higher temperatures into stable K₂Ge₄O₉ crystals. The glasses with x=7 or 8 both devitrify into K₂Ge₇O₁₅> crystals. The effects of the specific surface area of the samples on the devitrification mechanisms were established. Bulk nucleation predominates in the glass with x=4, while the glasses with x=7 or 8 crystallize from the surface. The activation energies for crystal growth were evaluated from the DTA curves. This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis of glycerol carbonate with high surface area ZrO2–KOH catalyst

High surface area ZrO₂–KOH sample was prepared and used the catalyst for the synthesis of glycerol carbonate (GC) from dimethyl carbonate (DMC) and glycerol. The structure properties of ZrO₂–KOH were characterized by XRD, BET, CO₂-TPD, XPS, and ICP-OES. It was found that the strong basicity of ZrO₂–KOH might be attributed to the oxygen vacancies as well as the big surface area. Experiments were developed to evaluate the effects of catalysis loading, proportion of reactants, temperature and reaction time on the conversion of glycerol to GC. The consequences showed that ZrO₂–KOH was a highly efficient basic catalyst for synthesis of GC from glycerol. The catalytic performance of ZrO₂–KOH is much better than that of ZrO₂–KOH–CP, ZrO₂–NH₄OH, and some reported heterogeneous catalysts. And the higher performance of ZrO₂–KOH was ascribed to the strong basicity. 99.43% conversion was obtained in a particular situation of catalyst/glycerol weight ratio of 3 wt%, DMC/glycerol molar ratio of 3:1, reaction temperature of 80 °C, and reaction time of 2 h. The plausible reaction mechanism for the transesterification on the strong basic active sites was discussed.

     

Glass forming ability and thermal stability of oxyfluoride glasses

New oxyfluoride glasses based on the system ZrO₂-Pr₂O₃-ZrF₄-BaF₂ were obtained, and the glass forming ability of this system was evaluated. The effects of glass composition on both thermal stability and the crystalline phases formed upon heat treatment were determined by the DSC and XRD methods, respectively. The composition with higher thermal stability and better glass forming ability contained 2 mol% of oxides.     

Copper ion-selective chalcogenide glass electrodes: Analytical characteristics and sensing mechanism

New copper ion-selective electrodes based on chalcogenide glasses, Cu_xAg_25?xAs_37.5Se_37.5, display high copper(II) ion sensitivity with Nernstian response in the range pCu 1–6, short response time, high selectivity, potential stability and reproducibility. These electrodes are 10–30 times more sensitive in strongly acidic media than crystalline copper ion-selective sensors and are superior to the copper(I) selenide electrode in selectivity and resistance to acids and oxidation. A model is proposed to explain the ion sensitivity of these chalcogenide glass sensors. The sensitivity depends on direct exchange of copper(II) ions between solution and the modified surface layer of the glass. The modified surface layer is formed as a result of partial destruction of the glass network on soaking in solution; its atomic density is 2.0–2.5 times less than that of the original glass. The structural defects and hollows make fast copper(II) ion migration within the modified surface layer possible. Exchange sites in this layer can be formed by both disproportionation and oxidation of copper(I) in the glass network, as well as by diffusion of copper(II) ion from solution in the case of glasses with low copper content. Experimental confirmation of this model is provided by x-ray, photo-electron and scanning Auger electron spectroscopy.     

Improved photocatalytic degradation of reactive blue 81 using NiO-doped ZnO–ZrO2 nanoparticles

In this study, the photocatalytic degradation of Reactive Blue 81 (RB81) using synthesized NiO-doped ZnO–ZrO₂ nanoparticles under UV irradiation was investigated. Then, the products were characterized by Scanning electron microscope (SEM), X-ray diffraction (XRD), and diffuse reflectance spectroscopy (DRS). The removal rate of RB81 using ZnO–ZrO₂ after 180?min of irradiation was 96.7%. Nickel oxide (NiO) was used as an additive to ZnO–ZrO₂ for improvement of RB81 degradation via photocatalysis process. Photodegradation of RB81 was achieved to 100% using ZnO–ZrO₂–NiO nanoparticles with ratio of 1:2:0.3 after 180?min of irradiation. There was a red shift in absorption bands (from 410?nm to 435?nm) observed in increasing of NiO to ZnO–ZrO₂ nanoparticle, that it might lead to a higher photocatalytic activity under visible light. Response surface methodology (RSM) was used for optimization of experimental and these results were obtained: solution pH = 3, ZnO–ZrO₂–NiO dosage = 15?mg/L, and the initial RB81 concentration = 5?mg/L. The photodegredation of RB81 followed pseudo-first order kinetic according to the Langmuir–Hinshelwood model.     

Facile synthesis and characterization of monocrystalline cubic ZrO2 nanoparticles

Crystalline ZrO₂ nanoparticles were prepared from zirconium isopropoxide by slow hydrolysis and subsequent hydrothermal treatment of solutions containing various amounts of sodium hydroxide at 180 °C. Whereas moderately basic solutions lead to the formation of nanoparticles of monoclinic ZrO₂ with plate-like morphology, and nanoparticles of the cubic ZrO₂ high-temperature polymorph with diameters of approx. 5 nm were obtained from strongly basic solutions. The morphology, structure and properties of as-synthesized nanoparticles were characterized using HRTEM, XRD, Raman spectroscopy, UV–vis, PL spectroscopy and BET measurements. The formation of both, the monoclinic and the cubic polymorph, was confirmed by electron microscopy and Raman spectroscopy. The crystallinity and morphology of the resulting ZrO₂ nanoparticles can be adjusted by the choice of the reaction conditions. The cubic ZrO₂ nanoparticles have a high surface area (300 m²/g) and exhibit a strong photoluminescence in the UV region.     

Structural characterization and photocatalytic activity of hollow binary ZrO2/TiO2 oxide fibers

The formation of hollow binary ZrO₂/TiO₂ oxide fibers using mixed precursor solutions was achieved by activated carbon fibers templating technique combined with solvothermal process. The samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), N₂ adsorption, X-ray photoelectron spectroscopy (XPS), UV-vis, and infrared (IR) spectroscopy. The binary oxide system shows the anatase-type TiO₂ and tetragonal phase of ZrO₂, and the introduction of ZrO₂ notably inhibits the growth of TiO₂ nanocrystallites. Although calcined at 575 °C, all hollow ZrO₂/TiO₂ fibers exhibit higher surface areas (>113 m²/g) than pure TiO₂ hollow fibers. The Pyridine adsorption on ZrO₂/TiO₂ sample indicates the presence of stronger surface acid sites. Such properties bring about that the binary oxide system possesses higher efficiency and durable activity stability for photodegradation of gaseous ethylene and trichloromethane than P25 TiO₂. In addition, the macroscopic felt form for the resulting materials is more beneficial for practical applications than traditional catalysts forms.     

Transparent oxyfluoride glass ceramics co-doped with Er and Yb - Crystallization and upconversion spectroscopy

Transparent glass ceramics in the system SiO₂-B₂O₃-PbO-CdO-PbF₂-CdF₂-YbF₃-ErF₃ showing infrared to visible anti-Stokes (upconversion) luminescence are studied in the present work. The glass compositions have been optimized in order to reduce the melting temperature and, hence, to obtain laboratory scale samples with good optical quality. Erbium-doped nanoscale Pb₄Yb₃F₁₇ crystals are precipitated in the precursor glasses during annealing at temperatures 30-40 K above T_g. A kinetically self-constrained growth explains the nano sizes of the crystals. Both the Stokes and anti-Stokes luminescence spectra of glasses could be explained with clustering of the Yb³⁺ and Er³⁺ ions in fluorine-rich regions. At the annealing temperature these regions act as nucleation precursors. The crystal growth further enhances the local concentration of these ions. Consequently, a series of energy transfer and energy cross relaxation processes occurs between adjacent rare earth ions leading to the observed luminescence spectra of the glass ceramics studied.     

Synthesis of Glass-Ceramics in Mixed Fluorozirconate–Phosphate Systems

Fluorozirconate-phosphate glasses of the ZrF₄–BaF₂–NaPO₃(LiPO₃) and ZrF₄–BaF₂–LaF₃–AlF₃–LiPO₃ systems doped with EuF₃, ErF₃, and NdF₃ were studied by the differential-thermal (DTA) and X-ray diffraction (XRD) analysis, luminescence spectroscopy, scanning and transmission electron microscopy (SEM and TEM) methods. Addition of the phosphate component up to 20 mol % decreases the glass transition temperature and increases the glass stability to crystallization. Heat treatment in the range >T_g–T_c1 of glass transition and first maxima of crystallization temperatures causes crystallization of nanosized β-BaZrF₆ particles. At LiPO₃ (NaPO₃) concentrations of more than 80 mol %, glasses containing a crystalline phase are formed during the synthesis process.

     

Nanostructured NiO based all solid state electrochromic device

A nickel oxide film with a thickness of 445 nm was deposited from nickel acetate precursor using the sol–gel dip coating method. The NiO films exhibit optical transmission of 84% at 550 nm and direct energy gap (E _gd) value is 3.64 eV. The FTIR spectrum of the films confirms the formation of Ni–O bond. XRD spectrum reveals the formation of nano crystallites along (111) and (200) planes with a particle size of 17 nm. The electrochromic properties have been studied using cyclic voltammetric (CV) technique. The optical transmission of a glass/FTO/NiO/ZrO₂/FTO/glass EC device is reported.     

Correlation between glass transition effect and structural changes in multicomponent iron phosphate-silicate glasses

Iron phosphate-silicate glasses from P₂O₅–SiO₂–K₂O–MgO–CaO–Fe₂O₃ system were subjected to the thermal and spectroscopic studies in order to gain information about their structure and thermal behavior in the range of glass transition effect. Research includes results obtained via DSC, MIR and DRIFT spectroscopy. Designated values of glass transition temperature and specific heat change slightly increases with Fe₂O₃ incorporation. Spectra collected during thermal treatment of glasses containing 2 and 30 mol% Fe₂O₃ exhibited various changes. Fe₂O₃ addition affected the glass structure by its reinforcement and led to its preservation during thermal treatment. The connection between density, molar volume, oxygen packing density and the chemical composition’s alteration were also established because of the direct dependence of physical properties and the structure. Obtained results supported thermal and spectroscopic studies. Conducted research is considered as a contribution to the knowledge about the family of iron phosphate glasses, which are known from their interesting properties and widely used applications.

     

Effect of fuel choice on conductivity and morphological properties of samarium doped ceria electrolytes for IT-SOFC

The present investigation is emphasized on the effect of various combustion agents on the crystal properties, surface microstructure, and oxygen ion conductivity of 20% mole-Sm doped ceria (Ce_0.80Sm_0.20O_1.90/SDC20) ceramics as solid electrolyte for IT-SOFCs. The most widely used combustion agents for engineering ceramic production as ethylene glycol, diethylene glycol, triethylene glycol, L-alanine, L-valine, glycine, citric acid monohydrate, urea, and EDTA-citric acid were compared in terms of SDC20 properties. X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and electrochemical impedance spectroscopy (EIS) were used to determine the microstructure properties, crystal structure and ionic conductivity of SDC20 powder. XRD pattern of the ceramics revealed the formation of single-phase fluorite structure. According to the results of electrochemical analysis, the maximum total ionic conductivity was observed in SDC20 electrolyte synthesized using triethylene glycol as the fuel among all the synthesized electrolytes (5.72 x 10^–2 S.cm^–1).     

Effect of hydrofluoric acid treatment on the crystallisation behaviour of Zr–Ti–Cu–Al–Ni metallic glass

The surface of the metallic glass Zr₅₉Ti₃Cu₂₀Al₁₀Ni₈ has been modified by hydrofluoric acid (HF) etching treatment. The devitrification and crystallisation process has been mainly studied by isothermal differential scanning calorimetry (DSC), X-ray diffractometry (XRD) and scanning electron microscopy (SEM). The nucleation-growth process is the mechanism of crystallisation; nevertheless the JMA-model is not applicable in every situation. Alternative methods are used to interpret the data. Results show the devitrification process is strongly affected by surface nucleation, which depends on the surface topology. Zr₃Al₂ is the first phase formed on the concave areas whereas the quasicrystalline and Zr₂Ni-based phases appears in the flatter ones. Nevertheless, the presence of an oxide surface layer acts upon the surface nucleation and dwarfs the consequences of such topological differences. Moreover, the quasicrystalline formation appears also to be in competition with the parallel formation of ZrO₂ due to thermal re-oxidation during the DSC experiments.     

Mechanical property and corrosion resistance of zirconia/polydopamine nanocomposite multilayer films fabricated via a novel non‐electrostatic layer‐by‐layer assembly technique

Zirconia/polydopamine (ZrO₂/PDA) nanocomposite multilayer films were constructed on Si substrate via a novel nonelectrostatic layer‐by‐layer (NELBL) assembly technique. The building block of this technique is the newly reported dopamine molecule, which can be attached to almost all material surfaces and undergo oxidation‐polymerization to form PDA layers; more importantly, the outer hydroxyl groups of the PDA layer can chelated with certain inorganic oxide nanoparticles to generate oxide films. Thus, ZrO₂/PDA nanocomposite multilayer films were fabricated by sequential NELBL deposition of PDA and ZrO₂ nanoparticles. The formation of the ZrO₂/PDA nanocomposite multilayer films was monitored by the water contact angle (WCA) and ellipsometric thickness measurements, while the microstructure of the fabricated films was analyzed by means of atomic force microscope (AFM), field emission scanning electron microscope (FESEM), X‐ray photoelectron spectrum (XPS), and X‐ray diffraction (XRD) analysis. The mechanical and anticorrosion behaviors of the annealed ZrO₂/PDA nanocomposite multilayers were found to be greatly enhanced as compared with that of the annealed homogeneous ZrO₂ film. The better mechanical and anticorrosion behaviors of the annealed ZrO₂/PDA nanocomposite multilayers than the annealed homogeneous ZrO₂ film may be closely related to their special microstructure. Namely, the organic–inorganic hybrid microstructure of the annealed ZrO₂/PDA nanocomposite multilayers may largely account for the increased nanohardness and corrosion resistance. Copyright © 2010 John Wiley & Sons, Ltd.