Synthesis and luminescence properties of hybrid organic-inorganic transparent titania thin film activated by in-situ formed lanthanide complexes

Stable transparent titania thin films were fabricated at room temperature by combining thenoyltrifluoroacetone (TTFA)-modified titanium precursors with amphiphilic triblock poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO, P123) copolymers. The obtained transparent titania thin films were systematically investigated by IR spectroscopy, PL emission and excitation spectroscopy and transmission electron microscopy. IR spectroscopy indicates that TTFA coordinates the titanium center during the process of hydrolysis and condensation. Luminescence spectroscopy confirms the in-situ formation of lanthanide complexes in the transparent titania thin film. TEM image shows that the in-situ formed lanthanide complexes were homogeneously distributed throughout the whole thin film. The quantum yield and the number of water coordinated to lanthanide metal center have been theoretically determined based on the luminescence data.     

Electrically conductive composite prepared by template polymerization of pyrrole into a complexed polymer

Electrically conducting polymer composite films have been synthesized by the exposure of poly(4-vinylpyridine) complexed with cupric ions to pyrrole and water vapor. To immobilize a stoichiometric amount of the oxidant inside the polymer matrix, the ratio of poly(4-vinylpyridine)/cupric ion = 1.8 was chosen. Polypyrrole was formed in this tailored structure by a template polymerization process. Opaque polymer composite films with electrical conductivity up to 60 (Ω cm)^?1 have been obtained by this method, However, slightly colored transparent composite thin films with a conductivity as high as 50 (Ω cm)^?1 were also produced. The electrically conducting polymer composite films and the metal-polymer complex have been characterized by XPS and IR spectroscopy, elemental analysis, EDX, and scanning electron microscopy. The polymerization process was also followed by use of a quartz crystal microbalance. © 1994 John Wiley & Sons, Inc.     

杂多化合物催化性能的研究——第四周期过渡金属钼磷三元杂多化合物的合成及表征

本文用改进的方法成功地合成了以第四周期二价过渡金属离子取代12-钼磷杂多酸中的一个钼,并保持Keggin结构的五个新化合物:Na_5[PZ(H_2O)Mo_(11)O_(39)·5H_2O,其中Z分别为Mn、Co、Ni、Cu、Zn,并利用红外光谱及热分析等手段对合成产物的结构及热稳定性作了系统的研究,结果表明,合成产物与12-钼磷杂多化合物具有类似的结构,但合成产物的热稳定性明显低于12-钼磷杂多化合物。     

Langmuir-Blodgett thin films of quantum dots: synthesis, surface modification, and fluorescence resonance energy transfer (FRET) studies

We describe herein studies on as-prepared hydrophobic ZnS-CdSe quantum dots (QDs) at the air-water interface. Surface pressure-area (pi-A) isotherms have been used to study the monolayer behavior. Uniform, lamellar multilayer thin films of QDs were deposited by the Langmuir-Blodgett (LB) technique. The role of two different surfactant systems commonly employed in the synthesis of these QDs (trioctylphosphine oxide-octadecylamine (TOPO-ODA) system and trioctylphosphine oxide-tetradecylphosphonic acid (TOPO-TDPA) system) on the monolayer behavior and the quality of thin films produced has been investigated. The thin films were characterized by quartz crystal microgravimetry (QCM), contact angle measurements, fluorescence spectroscopy, and transmission electron microscopy (TEM). These QD films were further modified by an amphiphilic polymer, poly(maleic anhydride-alt-1-tetradecene) (PMA). The hydrophobic interaction between the polymers and the surfactants attached to the QDs drove the self-assembly process. The carboxylic acid functional groups in the polymer were also used to immobilize avidin. We have demonstrated a proof of concept for the biosensing strategy wherein the avidin-coated QD films attracted biotinylated gold nanoparticles, resulting in fluorescence resonance energy transfer (FRET) quenching of the thin films.     

Evaporated thin films of insulating poly-(tetrabromo-p-phenylenediselenide)

It has been shown that thin insulating film at the interface transparent conductive oxide/organic electroluminescent film could improve the performance of organic electroluminescent diodes (OLED). Such insulating film can be inorganic or organic. Poly-(tetrabromo-p-phenylenediselenide) (PBrPDSe) has been proved to be an efficient insulating film in OLED. The properties of these evaporated PBrPDSe thin films have been systematically studied by IR absorption, X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, electron spin resonance and optical transmission measurements. It is shown that, when the deposition temperature is kept below the decomposition temperature of the polymer, tetrabromo-p-phenylenediselenide molecule is preserved during the deposition process. However the polymer, which is insoluble in powder form, becomes soluble after deposition. It can be concluded that films are mainly composed of oligomers of tetrabromo-p-phenylenediselenide.The electrical properties of SnO₂/PBrPDSe/Al thin films structures have been studied. The current-voltage characteristics exhibit a rectifying behaviour with a forward direction corresponding to a positive bias of the transparent conductive oxide film, the SnO₂.     

IR spectra and structure of poly(vinylamide) complexes with hydrogen peroxide

The IR spectra of anhydrous thin films of hydrogen peroxide complexes with cyclic and aliphatic poly(N-vinylamides) have been studied. Splitting of a band due to stretching vibrations of C=O groups in the IR spectra of the poly(vinylcaprolactam) complex is accounted for by the resonance interaction of v _C=O vibrations of two monomer units linked by a hydrogen peroxide molecule. The formation of a N-H···O=C intramolecular hydrogen bond between neighboring polymer units is responsible for the observed low absorption of hydrogen peroxide by N-vinylamide polymers and copolymers. The energy E _H of hydrogen bonds formed between hydrogen peroxide and polymer chain fragments has been estimated by quantum-mechanical calculations. Depending on the complex structure, the value of E _H varies from 13 to 29 kJ/mol.     

Photochromism of novel molybdate/alkylamine composite thin films.

Novel inorganic/organic composite films of molybdates with photochromic properties have been prepared by self-assembly using alkylammonium ions as a supramolecular template. Both 1-hexadecylammonium/polyoxomolybdate (C16-Mo) and 1-octadecylammonium/polyoxomolybdate (C18-Mo) composite films have been successfully fabricated. The elemental analysis and thermal gravimetric analysis show that the main product in the C16-Mo film was (C16H33NH3)4Mo8O26. The X-ray diffraction (XRD) results indicate that the composite films were lamellar in nature. The IR, Raman and X-ray photoelectron spectroscopy (XPS) results show that the polyoxomolybdate anions present as MoO6 octahedra and that the Mo species exists as Mo6+ in the freshly prepared films. The alkyl chains in the 1-hexadecylammonium chains were linear and the alkyl groups are an all-trans configuration. Upon UV irradiation of the C16-Mo films, some Mo6+ was reduced to Mo5+, some -NH3+ became -NH2 with a concomitant increase in the concentration of -OH groups on the molybdate moieties, and the films were colored. Thus, the photochromism of the films involves the reduction of Mo6+ to Mo5+, coupled with a proton transfer from 1-hexadecylammonium ions to an oxygen atom at the Mo site. In contrast to thin films of transition-metal oxides, which all show photochromism in the blue region of the electromagnetic spectrum, these composite films show photochromism in the violet region with the greatest absorbance change at 472 nm.     

Structural properties of lithium thio-germanate thin film electrolytes grown by radio frequency sputtering

In this study, lithium thio-germanate thin film electrolytes have been successfully prepared by radio frequency (RF) magnetron sputtering deposition in Ar gas atmospheres. The targets for RF sputtering were prepared by milling and pressing appropriate amounts of the melt-quenched starting materials in the nLi(2)S + GeS(2) (n = 1, 2, and 3) binary system. Approximately 1 μm thin films were grown on Ni coated Si (Ni/Si) substrates and pressed CsI pellets using 50 W power and 25 mtorr (～3.3 Pa) Ar gas pressures to prepare samples for Raman and Infrared (IR) spectroscopy, respectively. To improve the adhesion between the silicon substrate and the thin film electrolyte, a sputtered Ni layer (～120 nm) was used. The surface morphologies and thickness of the thin films were determined by field emission scanning electron microscopy (FE-SEM). The structural properties of the starting materials, target materials, and the grown thin films were examined by X-ray diffraction (XRD), Raman, and IR spectroscopy.     

杂多化合物催化性能的研究——第四周期过渡金属钼磷三元杂多化合物的合成及表征

本文用改进的方法成功地合成了以第四周期二价过渡金属离子取代12-钼磷杂多酸中的一个钼,并保持Keggin结构的五个新化合物:Na₅[PZ(H₂O)Mo₁₁O₃₉·5H₂O,其中Z分别为Mn、Co、Ni、Cu、Zn,并利用红外光谱及热分析等手段对合成产物的结构及热稳定性作了系统的研究,结果表明,合成产物与12-钼磷杂多化合物具有类似的结构,但合成产物的热稳定性明显低于12-钼磷杂多化合物。     

Structural and thermal behavior of polystyrene thin films using ATR–FTIR–NanoDSC measurements

Most studies report a depression of the glass transition temperature in thin polymer films. To gain insight into this behavior, we have simultaneously investigated the structure of materials and their thermal behavior by developing an ATR–FTIR–nano-differential scanning calorimeter (nanoDSC) hybrid instrument consisting of a ZnSe ATR crystal upon which the sample and a DSC-on-a-chip rests. FTIR spectra showed property changes with film thickness; nanoDSC did not. The relative absorbance of an IR peak at 797 cm⁻¹ was found to correlate with aging time in thin films, suggesting that conformational structure of thin films is critical to their thermal behavior.     

Effect of precipitants on polymer film porosity

IR spectroscopy and electron microscopy have been employed to study the effect of precipitants on the formation of porous structures in poly(vinyl alcohol)-based and modified polyacrylonitrile-based polymer films prepared by the wet casting method. Conditions for formation of porous structures in the polymer films are established as depending on parameters of solubility and pH of precipitants. The spectral method is tested for studying porosity of polymer materials in near and medium IR regions.     

Preparation and characterization of plasma-polymerized N-vinyl-2-pyrrolidone films

Thin films (< 1 μm) of plasma polymerized N-vinyl-2-pyrrolidone (PPNVP) have been prepared, using an inductively coupled RF glow discharge in a flow-through reactor system. PPNVP films were hydrophilic, smooth, and appeared morphologically homogeneous. The polymer deposition rate was found to increase linearly with NVP flow rate, and to decrease with the distance from the induction coil. ATR–FT–IR spectral studies suggested a highly branched polymer structure and included absorptions at 2150 and 1540 cm^?1 which were unique to the plasma polymer and derived from lactam ring opening/breaking reactions. ESCA studies demonstrated that, under a given set of plasma reaction conditions, the surface composition was consistent throughout the reactor. However, polymer composition was influenced by larger changes in the plasma energy, since the nitrogen content was found to decrease with increasing W/FM. This corresponded to concomitant increases in the advancing water contact angles and to small but reproducible changes in the IR spectrum.     

Dispersion of functional tetraphenylporphyrin-ligated metal into ultra-thin flexible acrylate films. 1. Preparation of thin films

As functional metal complexes, copper phthalocyanine (CuPc) and Cobalt (II) meso-tetraphenylporphyrin (CoTPP) were chosen to prepare metal complex/polymer hybrid thin films which were prepared by metal complex sublimation and reactive monomer evaporation onto the glass substrate in the bell jar reactor in vacuum conditions. The polarized transmission micrograph images show that the film deposited at 80 °C contains uniformly dispersed tiny grains and the film deposited at 30 °C is amorphous and homogeneous. As the deposition rate increases, the crystalline clusters were found and were dispersed uniformly. Those crystalline clusters are not to be developed by recrystallization process. Deposited metal complex/acrylate hybrid thin films were in situ photopolymerized. The kinetics of photopolymerization was investigated by attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR). The thickness of the films was about 200 nm. The reactive monomer acts as a solvent to avoid the recrystallization of metal complexes and to have two-compositional continuous phase. The percent of metal complex can be adjusted up to 60% by controlling the metal complex sublimation rate. A good achievement in the uniformity and continuity of the film matrix has been made and the recrystallization of metal complex in the hybrid films has not been observed.     

Plasma polymerization and deposition of glycidyl methacrylate on Si(100) surface for adhesion improvement with polyimide

Thin polymer films were deposited on Si(100) surfaces by plasma polymerization of glycidyl methacrylate (GMA) under different glow discharge conditions. The FT‐IR, X‐ray photoelectron spectroscopy (XPS), and amine treatment results suggested that the epoxide functional groups of the deposited films had been preserved to various extents, depending on the plasma deposition conditions. The use of a low radio frequency power (～ 5 W) and a relatively high system pressure (100–400 Pa) readily resulted in the deposition of thin films having nearly the same composition of the epoxide functional groups as that of the GMA homopolymer. The plasma‐polymerized GMA (PP‐GMA) thin films deposited on the Ar plasma‐pretreated Si(100) surfaces were retained to a large extent after acetone extraction, suggesting the presence of covalent bonding between the PP‐GMA layer and the Si surface. Thermal imidization of the poly(amic acid) precursor of polyimide on the GMA plasma‐polymerized Si(100) surface resulted in a strongly adhered polyimide film. The adhesion results further suggested that the GMA polymer had been grafted on the Si(100) surface and the epoxide functional groups had undergone reactive interaction (curing) with the carboxylic and amine groups of the poly(amic acid) during thermal imidization. Copyright © 2001 John Wiley & Sons, Ltd.     

MgCl2/R'nAl(OR)3-n: an excellent activator/support for transition-metal complexes for olefin polymerization

A new and effective method for the activation, and simultaneously, immobilization of bis(phenoxyimine) early-transition-metal complexes for olefin polymerization (known as FI catalysts), which makes use of MgCl(2)/R'(n)Al(OR)(3-n) as an activator/support, has been developed. Ti-, Zr-, and V-FI catalysts combined with this MgCl(2)-based compound can form highly active MgCl(2)-supported single-site catalysts capable of demonstrating superior catalytic properties, compared to the corresponding homogeneous methylaluminoxane- (Ti- and Zr-FI catalysts) or alkylaluminum-activation systems (V-FI catalysts), in terms of their catalytic activity, molecular weight, stereoselectivity, and comonomer incorporation. Additionally, these new catalysts can produce polymers of significant morphology with high efficiency. Notably, the MgCl(2)-based compounds can also effectively activate and immobilize the early-to-late transition-metal complexes that have emerged recently. Thus, the application of MgCl(2)-based compounds as activators/supports for transition-metal complexes for olefin polymerization provides a conceptually new strategy for the development of methylaluminoxane- and borate-free, high-performance, single-site catalysts capable of controlling polymer morphology.     

钨磷酸(钨硅酸)/聚乙烯醇复合物的制备和光、电性质研究

Kessin型的杂多酸及其盐是多酸化学中研究得最多的物种[1],近年来,以Keggin型的钨磷酸、钨硅酸为代表的多种杂多酸在固体和材料化学领域受到人们的关注[2],并在固体修饰电极、光（电）致变色材料、离子选择性电极和传感器等方面得到了广泛应用[3-5]．本文报道了Keggin型的钨磷酸、钨硅酸／聚乙烯醇复合物的合成、表征、光致变色性质及导电性．1实验方法技文献[6]方法制备H4[SiW12O40]·mH2O和H2［PW12O40］·nH对晶体,含水量用热重分析测得．将聚合度为1800士100的聚乙烯酸（PVA）0．5g溶于200mL沸水中,在65C,搅拌条件下分批…     

Self‐organization and luminescent properties of nanostructured europium (III)–block copolymer complex thin films

We introduce a simple method to create nanosized, ordered, and highly luminescent thin film of Eu (III)–block copolymer complex. Micelles of polystyrene–block‐poly(4‐vinylpyridine) (PS‐b‐P4VP) in P4VP‐selective solvents (ethanol/N,N‐dimethylformamide (DMF) mixture) serve as nanoreactors for the synthesis of Eu(III)–block copolymer complex with the presence of 1,10‐phenanthroline (Phen) as cooperative ligand. The resulted quaternary complexes were characterized by FT‐IR spectra, ¹⁵N NMR spectra, and elemental analysis, indicative of a composition of Eu(III)–(PS‐b‐P4VP)–Phen–5DMF. Atomic force microscopy and transmission electron microscopy investigations reveal that the Eu(III)–(PS‐b‐P4VP)–Phen–5DMF complex can self‐organize into hexagonally ordered thin films when dip‐coated from the solution onto silicon or silica glass substrates. Such ordered thin films can emit red fluorescence of Eu³⁺ with strong intensity and long lifetime. This method can be easily extended to prepare other ordered luminescent rare earth–polymer complexes thin films. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2181–2189, 2005     

Electrochemical preparation and structural characterization of Co thin films and their anomalous IR properties

Nanometer scale cobalt thin films of different structures and thicknesses supported on glassy carbon were prepared by electrochemical deposition under cyclic voltammetric conditions (denoted nm-Co/GC(n)). The thickness of Co thin films was altered systematically by varying the number (n) of potential cycling within a defined potential range in electrodeposition. Electrochemical in situ scanning tunneling microscopy (STM) and ex situ scanning electron microscopy (SEM) were employed to characterize the surface structure of Co thin films. It has been illustrated that the Co thin films were uniformly composed of Co nanoparticles, whose structure and size varied with increasing n. The structure of nanoparticles inside the Co thin films underwent a transition from bearded nanoparticles to multiform nanoparticles and finally to hexagonal nanosheets, accompanying with an increase of average size. In situ FTIR reflection spectroscopic studies employing CO adsorption as probe reaction revealed that the Co thin films all exhibited anomalous IR properties; that is, along with their different nanostructures they presented abnormal IR effects, Fano-like IR effects, and surface-enhanced IR absorption effects. CO adsorbed on Co thin films dominated by bearded nanoparticles yielded abnormal IR absorption bands; that is, the direction of the bands is inverted completely, with enhanced intensity in comparison with those of CO adsorbed on a bulk Co electrode. The enhancement of abnormal IR absorption has reached a maximal value of 26.2 on the nm-Co/GC(2) electrode. Fano-like IR features, which describe the bipolar IR bands with their positive-going peak on the low wavenumbers side, were observed in cases of CO adsorbed on Co thin films composed mainly of multiform nanoparticles, typically on the nm-Co/GC(8) electrode. IR features were finally changed into surface-enhanced IR absorption as CO adsorbed on the nm-Co/GC(30) electrode, on which the Co thin film is dominated by Co hexagonal nanosheets.     

Lanthanide radii controlled one-dimensional polymer and dinuclear complexes and their fluorescent properties

A bi-phosphonate ligand tetraethyl-(2,3,5,6-tetramethyl-1,4-phenylene) bis(methylene)diphosphonate has been designed and synthesized. The bi-phosphonate as a bridging ligand reacts with lanthanide nitrates forming four different types of 1D coordination complexes: ribbon polymer (type I), semi-ribbon polymer (type II), zigzag polymer (type III), and dinuclear-triligand short chain (type IV), which changed according to the decrease of the radius of the lanthanide. They have been characterized by IR spectroscopy, elemental analysis, and X-ray diffraction spectroscopy. The photophysical properties of Sm(3+), Eu(3+), Tb(3+) and Dy(3+) complexes at room temperature were also investigated. They exhibit strong fluorescence by excitation of the Ln(3+) ion absorption bands and the quantum yield values of Eu(3+) and Tb(3+) complexes are no less than 20%.     

Processing-induced chromism in thin films of polythiophene derivatives

Langmuir-Blodgett films of amphiphilic poly[3-oligo(oxyethylene)-4-methylthiophene] have been obtained. The resulting thin films are poorly conjugated, with a maximum of absorption at 405 nm which remains almost constant upon heating or cooling. In contrast, cast thin films of this polymer exhibit a maximum of absorption at 550 nm and show interesting thermochromic effects. These results to indicate that the method of preparation of thin films can have a significant influence on the conformational structure of the polymer at room temperature and, consequently, on its thermochromic behaviour.