Photoelectrochemical cells based on nanocrystalline TiO2 synthesized by high temperature hydrolysis of ammonium dihydroxodilactatotitanate(IV)

Photoelectric parameters of dye-sensitized solar cells (DSSC) based on nanocrystaline titanium dioxide synthesized by several methods are studied. The lifetime of charge carriers (electrons) is shown to be 10 ms for DSSC with anodes of TiO₂ synthesized by hydrolysis of ammonium dihydroxodilactatotitanate(IV) (DLTA) and about 7 ms for anodes of commercial titanium dioxide (AEROXIDE®, TiO₂, P 25, Evonik), which points to the lower recombination losses for anodes of DLTA. The transition times for both cell versions are close to one another and equal to 10 ms; under these conditions, the diffusion coefficient of electrons is assessed to be ca. 10^?5 cm² s^?1. The comparable transition times and lifetimes of electrons in DSSCs under study suggest that a part of photogenerated electrons is lost at the diffusion to the conducting substrate.     

Mapping of the Photoinduced Electron Traps in TiO2 by Picosecond X‐ray Absorption Spectroscopy

Titanium dioxide (TiO₂) is the most popular material for applications in solar‐energy conversion and photocatalysis, both of which rely on the creation, transport, and trapping of charges (holes and electrons). The nature and lifetime of electron traps at room temperature have so far not been elucidated. Herein, we use picosecond X‐ray absorption spectroscopy at the Ti K‐edge and the Ru L₃‐edge to address this issue for photoexcited bare and N719‐dye‐sensitized anatase and amorphous TiO₂ nanoparticles. Our results show that 100 ps after photoexcitation, the electrons are trapped deep in the defect‐rich surface shell in the case of anatase TiO₂, whereas they are inside the bulk in the case of amorphous TiO₂. In the case of dye‐sensitized anatase or amorphous TiO₂, the electrons are trapped at the outer surface. Only two traps were identified in all cases, with lifetimes in the range of nanoseconds to tens of nanoseconds.     

Preparation of Cu-doped TiO2 via refluxing of alkoxide solution and its photocatalytic properties

Cu-doped TiO₂ was prepared by the refluxing of a mixture of copper and titanium alkoxides. The refluxing improved the Cu²⁺ dispersion in the TiO₂ and formed effective Ti–O–Cu bonds. The impurity states due to the highly dispersed Cu²⁺ were presumed to trap the electrons in the conduction band of the TiO₂ and prevent charge recombination of the electrons and holes. Consequently, the prolonged charge separation duration was suggested to enhance the photocatalytic activity of the Cu-doped TiO₂. This enhancement was confirmed by the hydroxyl radical generation and organic compound degradation. The Ti–O–Cu bonds and electronic interaction between Cu and Ti should effectively promote the electron trapping. The Cu-doped TiO₂ exhibited a visible light-induced activity due to the transition from the TiO₂ valence band to the Cu²⁺ impurity states.     

Influence of Zn(II) adsorption on the photocatalytic activity and the production of H2O2 over irradiated TiO2

The photocatalytic activity of semiconductor oxides, in particular TiO₂ powders or colloids, is a complex function of bulk (light absorption and scattering, charge carrier mobility and recombination rate) and surface (structure, defects and reconstruction, charge, presence of adsorbate, surface recombination centers) properties. Among surface modifications, the inner sphere surface complexation of metal cations can change the surface charge of the metal oxide, thus changing the surface activity coefficient of ionic substrates, the band edge positions, as well as the mechanism and kinetic of interfacial electron transfer by blocking surface trapping sites for photogenerated carriers (≡Ti?OH). In this work we show that in anatase/water systems under band-gap irradiation, both the organic substrate (formate) oxidation initiated by photogenerated valence band holes and the formation of hydrogen peroxide from O₂ reduction (by conduction band electrons) is strongly influenced by the presence of Zn²⁺ cations. Depending on the pH, the formate oxidation rate can be enhanced or nearly completely inhibited. The observed result can be rationalized by considering the fraction of ≡Ti?OH surface sites blocked by inner sphere complexation of Zn²⁺ as a function of pH. When this fraction is low, the more positive surface charge favors formate oxidation, whereas when the fraction is high the almost complete blockage of ≡Ti?OH surface sites by Zn²⁺ stops almost entirely formate oxidation. Interestingly, the surface complexation of Zn²⁺ is accompanied by an increasing production of H₂O₂ during formate degradation in the presence of O₂. Zn(II) cations are not complexed by peroxide/superoxide species derived from O₂ reduction. When ≡Ti?OH sites are blocked by Zn²⁺, the complexation on the TiO₂ surface of peroxide/superoxide species is inhibited, hindering their further transformation. The results presented demonstrate that the combined effect of pH and surface complexation of redox inert cations greatly influences both the oxidative and reductive processes during the photocatalytic process over TiO₂.     

Separation of titanium, iron and aluminium on a chelating resin with benzoylphenylhydroxylamine group and application to bauxite and clay

Summary A chelating polystyrene based resin containing N-benzoyl-N-phenylhydroxylamine has been sythesized by two methods and characterized. Conditions for quantitative separation of Ti(IV), Fe(III) and Al(III) on the resin have been studied. A method has been developed for the determination of these three metal ions in bauxite or clay samples after their separation on the resin with recoveries of 98.5–99.5% for different metal ions. The maximum sorption values are observed at pH 1, 2.5 and 2.5 for Ti(IV), Fe(III) and Al(III), respectively, which are recovered by successive elution with 1 mol/l H₂SO₄, 2 mol/l HCl and 4 mol/l H₂SO₄ in the above order.     

低温吸附制备Au-TiO2复合薄膜及其光电化学性质

在低温条件下将预先合成的Au溶胶吸附到TiO₂薄膜上以制备纳米Au-TiO₂复合薄膜,以超高分辨率场发射扫描电镜(FESEM)、X射线衍射(XRD)及X射线光电子能谱(XPS)表征Au-TiO₂膜,并在UV辐照下测定了Au-TiO₂薄膜电极的光电化学性质。纳米Au呈金属态,平均粒径为(4.3±1.2) nm,负载量高,均匀地沉积于TiO₂薄膜表面。光电化学测试表明,沉积纳米Au后,TiO₂电极的光生电流提高近5倍,光生电压明显向负值增大,说明纳米Au可增强光生载流子的分离效率,促进电荷在电极与溶液界面间的转移。Au-TiO₂电极的电荷传递法拉第阻抗(R_ct)是TiO₂电极的一半,说明负载的纳米Au粒抑制了光生电子-空穴的复合,提高了电极中载流子浓度。     

Photocatalytic activity of polyaniline/Fe-doped TiO2 composites by in situ polymerization method

This study was focused on the photocatalytic activity of polyaniline (Pani)/iron doped titanium dioxide (Fe–TiO₂) composites for the degradation of methylene blue as a model dye. TiO₂ nanoparticles were doped with iron ions (Fe) using the wet impregnation method and the doped nanoparticles were further combined with Pani via an in situ polymerization method. For comparison purposes, Pani composites were also synthesized in the presence undoped TiO₂. The photocatalyst and the composites were characterized by standard analytical techniques such as FTIR, XRD, SEM, EDX and UV–Vis spectroscopies. Fe–TiO₂ and its composites exhibited enhanced photocatalytic activity under ultraviolet light irradiation. Improved photocatalytic activity of Fe–TiO₂ was attributed to the dopant Fe ions hindering the recombination of the photoinduced charge carriers. Pani/Fe–TiO₂ composite with 30?wt.% of TiO₂ nanoparticles achieved 28% dye removal and the discoloration rate of methylene blue for the sample was 0.0025?min^?1. FTIR, XRD, SEM, EDX and UV–Vis spectroscopies supported the idea that Fe ions integrated into TiO₂ crystal structure and Pani composites were successfully synthesized in the presence of the photocatalyst nanoparticles. The novelty of this study was to investigate the photocatalytic activity of Pani composites, containing iron doped TiO₂ and to compare their results with that of Pani/TiO₂.     

Electrochemical Fabrication and Properties of Highly Ordered Fe‐Doped TiO2 Nanotubes

Highly‐ordered Fe‐doped TiO₂ nanotubes (TiO₂nts) were fabricated by anodization of co‐sputtered Ti–Fe thin films in a glycerol electrolyte containing NH₄F. The as‐sputtered Ti–Fe thin films correspond to a solid solution of Ti and Fe according to X‐ray diffraction. The Fe‐doped TiO₂nts were studied in terms of composition, morphology and structure. The characterization included scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, X‐ray diffraction, UV/Vis spectroscopy, X‐ray photoelectron spectroscopy and Mott–Schottky analysis. As a result of the Fe doping, an indirect bandgap of 3.0 eV was estimated using Tauc’s plot, and this substantial red‐shift extends its photoresponse to visible light. From the Mott–Schottky analysis, the flat‐band potential (E_fb) and the charge carrier concentration (N_D) were determined to be ?0.95 V vs Ag/AgCl and 5.0 ×10¹⁹ cm^?3 respectively for the Fe‐doped TiO₂nts, whilst for the undoped TiO₂nts, E_fb of ?0.85 V vs Ag/AgCl and N_D of 6.5×10¹⁹ cm^?3 were obtained.     

Cooperative effect of Fe and Ti species over Fe–Ti–Ox catalysts on the catalytic hydrolysis performance of hydrogen cyanide

FeO_x, TiO₂, and Fe–Ti–O_x catalysts were synthesized and used in the catalytic hydrolysis of hydrogen cyanide (HCN). Nearly 100% HCN conversion was achieved at 250 °C over the Fe–Ti–O_x catalyst. TiO₂ rutile was detected over TiO₂, but not over Fe–Ti–O_x, which suggested that the interaction between Fe and Ti species could inhibit the TiO₂ phase transition. Furthermore, the interaction between Fe and Ti species over Fe–Ti–O_x could promote the selectivity of NH₃ and CO. The mechanism of hydrolysis of HCN over FeO_x, TiO₂, and Fe–Ti–O_x can be given as follows: HCN + H₂O → methanamide → ammonium formate → formic acid → H₂O + CO.     

Electrochemical amination. Functionalization of anisole in solutions of 4.0–6.0 M H<Subscript>2</Subscript>SO<Subscript>4</Subscript> and acetic acid

The electrochemical amination of anisole in 4.0–6.0 M H₂SO₄ solutions containing CH₃COOH and small amounts of water is studied with the use of the Ti(IV)/Ti(III)-NH₂OH system. Under these conditions, the products of radical substitution are para- and ortho-anisidines. Their total current efficiency and yield by hydroxylamine are 82.0% at a complete conversion of the source of amine radicals. Owing to the chain mechanism, the electrochemical process is terminated upon consumption of no more than 0.5 electrons per NH₂OH molecule. At a small charge passed through the electrolyte, the anisidines current efficiency can exceed 380%.     

A comparative study of high-spin manganese and iron complexes

Different metal complexes of the general form M(OH) _n (H₂O)_{6– n} have been studied for manganese and iron. Oxidation states considered for manganese are Mn(III), Mn(IV) and Mn(V) and for iron Fe(II), Fe(III) and Fe(IV). Oxygen containing ligands are used throughout with varying numbers of hydroxyl and water ligands. Some metal-oxo and some charged complexes were also studied. Large Jahn-Teller distortions were found for the Mn(III) and Fe(IV) complexes. Consequences of these distortions are that water ligands have to be placed along the weak JT-axis and that five-coordination by a loss of one of these water ligands is quite competitive with six-coordination in particular for manganese. For Fe(II) and Fe(III) lower coordinations than six are preferred due to the presence of two repulsive e _g electrons. For the metal-oxo complexes five-coordination is also preferred due to the strong trans effect from the oxo ligand. All complexes studied have high-spin ground states. An interesting effect is that the spin is much more delocalized on the ligands for the iron complexes than for the manganese complexes. This effect, which is chemically important for certain iron enzymes, is rationalized by the large number of 3d electrons on iron. For manganese with only five 3d electrons no spin delocalization is needed to obtain the proper high-spin states. Received: 4 February 1997 / Accepted: 24 February 1997     

Suppressing Interfacial Charge Recombination in Electron-Transport-Layer-Free Perovskite Solar Cells to Give an Efficiency Exceeding 21 %

The performances of electron-transport-layer (ETL)-free perovskite solar cells (PSCs) are still inferior to ETL-containing devices. This is mainly due to severe interfacial charge recombination occurring at the transparent conducting oxide (TCO)/perovskite interface, where the photo-injected electrons in the TCO can travel back to recombine with holes in the perovskite layer. Herein, we demonstrate for the first time that a non-annealed, insulating, amorphous metal oxyhydroxide, atomic-scale thin interlayer (ca. 3 nm) between the TCO and perovskite facilitates electron tunneling and suppresses the interfacial charge recombination. This largely reduced the interfacial charge recombination loss and achieved a record efficiency of 21.1 % for n-i-p structured ETL-free PSCs, outperforming their ETL-containing metal oxide counterparts (18.7 %), as well as narrowing the efficiency gap with high-efficiency PSCs employing highly crystalline TiO₂ ETLs.     

Review on Undoped/Doped TiO2 Nanomaterial; Synthesis and Photocatalytic and Antimicrobial Activity

This review covers the various synthetic methods of doped and undoped TiO₂ nanomaterials, ranging from single‐doped and co‐doped to multidoped with transition‐metal ions, rare earth metal ions, and other metals and nonmetals ions. The effects of doping on the physiochemical propertiesas well as the photocatalytic and antimicrobial activities of TiO₂ nanomaterial are discussed. The results from the literature show that doping of TiO₂ shifts the absorption edge to the visible region as a result of the decrease in the bandgap due to the formation of new energy levels in the bandgap. The dopent also acts as a trapping center for electrons and holes, thereby reducing the recombination rate of charge carriers and increasing the photocatalytic and antimicrobial activity of TiO₂ nanomaterials. All multidoped TiO₂ nanomaterials show higher activity than their undoped, single‐doped, and co‐doped counterparts.     

Preparation of TiO<Subscript>2</Subscript>/activated carbon with Fe ions doping photocatalyst and its application to photocatalytic degradation of reactive brilliant red K2G

Titanium dioxide coated on activated carbon (AC) with Fe ions doping (Fe-TiO₂/AC) composite was prepared by an improved sol-gel method. The photocatalytic activities were tested by photocatalytic degradation of reactive brilliant red K2G in solution. The results show that in comparison with the agglomeration of pure TiO₂, the TiO₂ nanoparticles are well dispersed in the AC matrix, of which sizes are decreased with Fe ions doping. Additionally, the iron species on TiO₂ of composite are Fe₂O₃ and FeO, which do not affect the crystalline structures of TiO₂ nanoparticles. The AC matrix and iron doping content influence the fluorescence intensity of composite due to their effects on recombination probability of hole-electron pairs. Compared with TiO₂, 0.3% Fe-TiO₂, TiO₂/AC, 0.5% Fe-TiO₂/AC and 0.1% Fe-TiO₂/AC, the 0.3% Fe-TiO₂/AC shows the highest photoactivity with the complete mineralization of K2G for finite time due to the optimum Fe ions content and AC matrix. Furthermore, the kinetic constant (k = 0.0229 min⁻¹) of 0.3% Fe-TiO₂/AC composite is more than the sum of both TiO₂/AC (0.0154 min⁻¹) and 0.3% Fe-TiO₂ (0.0057 min⁻¹) because coexistence of the AC and Fe ions has an enlarging effect on improving the photoactivity of TiO₂. Supported by the Education Department Foundation of Hunan Province (Grant No. 08B063) and Science and Natural Science Foundation of Hunan Province (Grant No. 09JJ6101)     

Enhancing photocatalytic activity of titanium dioxide through incorporation of MIL‐53(Fe) toward degradation of organic dye

Photocatalytic activity of titanium(IV) oxide (TiO₂) can be enhanced through modification of its surface‐active sites. Here, iron(III) carboxylate [MIL‐53[Fe]]‐incorporated TiO₂ (as MIL‐53(Fe)/TiO₂) was prepared using a hydrothermal method. This material was then calcined at 500°C to obtain a MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ photocatalyst. A photocatalytic study of MIL‐53(Fe)/TiO₂ and MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ toward cationic methylene blue (MB) and anionic methyl orange (MO) showed that MIL‐53(Fe)/TiO₂ (0.25 wt%) and MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ (0.75 wt%) resulted the best degree of dye degradation. The MIL‐53(Fe)‐derived γ‐Fe₂O₃/TiO₂ (0.75 wt%) composite for instance is capable of degrading almost 100% of 20‐ppm MB and MO, respectively, within 6 hr. Photocatalytic degradation of MB and MO was well fitted to the Langmuir‐Hinshelwood pseudo‐first order kinetics model, which indicates physisorption as the key partway that facilitates dye decomposition on the surface of a photocatalyst under UV‐A irradiation. This study provides new insights into the exploration of MILs/TiO₂ materials for the environmental remediation and pollution control.     

Synthesis and Characterization of Photocatalytic Porous Fe3+/TiO2 Layers on Glass

Wet chemical synthesis and preliminary photocatalytical characteristics of titania and Fe(III)-containing TiO₂ layers are presented. A highly stable coating colloids could be prepared under base- as well as acid-catalyzed condensation conditions. Structural properties of the as-prepared wet gels and sintered films were investigated using SEM, TEM, XRD as well as optical absorption spectroscopy, DTA-TG analysis and photomineralisation studies. X-ray amorphous wet titania gel layers start to crystallize at 500°C forming the characteristic anatase phase. In the presence of iron ions (Fe/Ti = 1), nanocrystalline FeTiO₃ ilmenite phase forms. Both TiO₂ and Fe-containing TiO₂ films demonstrate a photocatalytic activity in the process of the photomineralization of dichloroacetic acid.     

掺杂纳米金粒子的火焰氧化TiO2膜的光电化学性质的研究

A nano-Au modified TiO2 electrode was prepared via the oxidation of Ti sheet in flame and subsequent modification with gold nanoparticles. The results of SEM and TEM measurements show that the Au nanoparticles are well dispersed on TiO2 surface. A near 2-fold enhancement in photocurrent was achieved upon the modification with Au nanoparticles. From the results of photocurrent and electrochemical impedance experiments it was found that the flatband potential of nano-Au/TiO2 electrode negatively shifted about 100 mV in 0.5 mol/L Na2SO4 solutions compared with that of bare TiO2 electrode. The improvement of photoelectrochemical performance was explained by the inhibition for charge recombination of photo-induced electrons and holes, and the promotion for interracial charge-transfer kinetics at nano-Au/TiO2 composite film. Such nanometal-semiconductor composite films have the potential application in improving the performance of photoelectrochemical solar cells.     

A Rutile TiO2 Electron Transport Layer for the Enhancement of Charge Collection for Efficient Perovskite Solar Cells

Interfacial charge collection efficiency has demonstrated significant effects on the power conversion efficiency (PCE) of perovskite solar cells (PSCs). Herein, crystalline phase‐dependent charge collection is investigated by using rutile and anatase TiO₂ electron transport layer (ETL) to fabricate PSCs. The results show that rutile TiO₂ ETL enhances the extraction and transportation of electrons to FTO and reduces the recombination, thanks to its better conductivity and improved interface with the CH₃NH₃PbI₃ (MAPbI₃) layer. Moreover, this may be also attributed to the fact that rutile TiO₂ has better match with perovskite grains, and less trap density. As a result, comparing with anatase TiO₂ ETL, MAPbI₃ PSCs with rutile TiO₂ ETL delivers significantly enhanced performance with a champion PCE of 20.9 % and a large open circuit voltage (V_OC) of 1.17 V.     

SrTiO3/TiO2 Hybridstructure as Photoanode in Dye‐Sensitized Solar Cell

In dye‐sensitized solar cells (DSSCs), the charge recombination at the TiO₂/dye/electrolyte interface greatly influences the photoelectron conversion efficiency. Hybrid semiconductor materials with matched band potentials are designed to reduce the charge recombination. In this study, SrTiO₃/TiO₂ hybridstructure was synthesized by using TiO₂ nanoparticles as template in a hydrothermal, showing a negative shift in the flat band potential. The DSSC with the SrTiO₃/TiO₂ anode exhibits an increased photovoltage and a reduced photocurrent. The suppression of charge recombination at the TiO₂/dye/electrolyte interface was observed in the electrochemical impedance spectroscopy, causing an improvement in the photovoltage. However, the SrTiO₃/TiO₂ system shows an obstructed electrons injection from the dye to SrTiO₃/TiO₂, limiting the photocurrent performance. The photoelectrochemical properties of the SrTiO₃/TiO₂ system are discussed in detail herein.     

Synthesis and properties of titanomagnetite (Fe3−xTixO4) nanoparticles: A tunable solid-state Fe(II/III) redox system

Titanomagnetite (Fe_3−xTi_xO₄) nanoparticles were synthesized by room temperature aqueous precipitation, in which Ti(IV) replaces Fe(III) and is charge compensated by conversion of Fe(III) to Fe(II) in the unit cell. A comprehensive suite of tools was used to probe composition, structure, and magnetic properties down to site-occupancy level, emphasizing distribution and accessibility of Fe(II) as a function of x. Synthesis of nanoparticles in the range 0 ? x ? 0.6 was attempted; Ti, total Fe and Fe(II) content were verified by chemical analysis. TEM indicated homogeneous spherical 9-12 nm particles. μ-XRD and Mössbauer spectroscopy on anoxic aqueous suspensions verified the inverse spinel structure and Ti(IV) incorporation in the unit cell up to x ? 0.38, based on Fe(II)/Fe(III) ratio deduced from the unit cell edge and Mössbauer spectra. Nanoparticles with a higher value of x possessed a minor amorphous secondary Fe(II)/Ti(IV) phase. XANES/EXAFS indicated Ti(IV) incorporation in the octahedral sublattice (B-site) and proportional increases in Fe(II)/Fe(III) ratio. XA/XMCD indicated that increases arise from increasing B-site Fe(II), and that these charge-balancing equivalents segregate to those B-sites near particle surfaces. Dissolution studies showed that this segregation persists after release of Fe(II) into solution, in amounts systematically proportional to x and thus the Fe(II)/Fe(III) ratio. A mechanistic reaction model was developed entailing mobile B-site Fe(II) supplying a highly interactive surface phase that undergoes interfacial electron transfer with oxidants in solution, sustained by outward Fe(II) migration from particle interiors and concurrent inward migration of charge-balancing cationic vacancies in a ratio of 3:1.