Modification and Application of Poly(Ethylene Terephethalate) Nonwoven Fiber Using Octadecyl Acrylate and Acrylic Acid as Oil Sorbers

Three series of crosslinked octadecyl acrylate and acrylic acid copolymers were prepared through suspension copolymerization based on acrylic acid content (10, 30, 50%wt. ratio). Divinyl benzene (DVB) was used as a crosslinker with different weight ratios (1, 4 and 10%). Isopropyl alcohol or dioctyl phthalate and methyl benzoate were used as two different reaction solvents in the presence of ABIN as initiator. The prepared crosslinked copolymers were characterized by SEM, TGA and FTIR spectroscopic analyses. The prepared polymers were coated onto poly(ethylene terephethalate) nonwoven fiber (NWPET). The effect of copolymerization feed composition, crosslinker wt% and reaction media or solvent on swelling properties of crosslinked polymers were studied through the oil absorption tests in toluene and 10% of diluted crude oil with toluene. It was noticed that the maximum swelling of crosslinked copolymers was increased from 30 to 100 g/g after grafting of copolymers onto NWPET.     

Dispersion copolymerization of styrene and divinylbenzene: Synthesis of monodisperse,uniformly crosslinked particles

Monodisperse, crosslinked polystyrene latexes were prepared by the dispersion technique. Some general observations regarding the effect of initial reagent concentrations on final particle size and size distribution are offered, in addition to a detailed discussion concerning the problems encountered with the use of the crosslinker divinylbenzene (DVB) in latex preparation. Particles synthesized in very polar media were found to reach their growth plateau sooner than those made in less polar surroundings. This trend was proposed to be the result of more effective nucleation in polar environments, which increases available surface area, thereby allowing the rapid replacement of monomer consumed within the particle phase during the polymerization. Attempts to favorably influence the growth rate and size distribution of particles during the reaction were unsuccessful, underlining the importance of the nucleation period in defining particle size characteristics. Up to 1% DVB was successfully incorporated in the synthesis of coagulum-free, monodisperse, 5 μm beads, by controlling the entry of the crosslinker into the particle phase during the major particle growth period. Latex stability is proposed to be largely dependent on the mobility of the adsorbed steric stabilizer. © 1995 John Wiley & Sons, Inc.     

Preparation of a novel polymeric fluorescent nanoparticle

A new type of narrowly dispersed fluorescent crosslinked polystyrene (PS) nanoparticles (20-50 nm) was synthesized via a modified microemulsion copolymerization of styrene, crosslinker divinyl benzene (DVB) and a hydrophilic comonomer amino ethyl methacrylate hydrochloride (AEMH), in the presence of pyrene. Characterized by steady-state fluorescence spectra, these nanoparticles show high luminescent intensity and the embedded pyrene has a negligible desorption from the nanoparticles. The emission intensity I₁ of the pyrene in the crosslinked nanoparticles is 40 times higher than that of pyrene in toluene or styrene solution with the same concentration. The fluorescence emission intensity can be varied by the amount of the monomer, crosslinker and pyrene, but is influenced little by the amount of AEMH in the range of investigation. The surface of the nanoparticles is modified by amino and amidino functional groups introduced by the comonomer and the initiator 2, 2'-azobis(2-amidinopropane) dihydrochloride (V₅₀), which controls the zeta potential on the particle surface.     

Synthesis of crosslinked poly(butyl methacrylate‐co‐pentaerythritol triacrylate) gel by single electron transfer‐living radical polymerization and its oil‐absorbing properties

A novel high oil‐absorbing crosslinked gel was synthesized by copolymerization of butyl methacrylate (BMA) with a small amount of pentaerythritol triacrylate (PETA) crosslinker using single electron transfer‐living radical polymerization (SET–LRP) initiated with carbon tetrachloride (CCl₄) and catalyzed by Cu(0)/hexamethylenetetramine (HMTA) in N, N‐dimethylformamide (DMF). The polymerization followed first‐order kinetics as indicated by linear increase of monomer concentration with reaction time. Effects of reaction temperature, crosslinker, initiator, and catalyst on the oil‐absorbing properties of the crosslinked gel were investigated in detail. The oil absorptions of the crosslinked gel to chloroform, toluene could reach 51.9, 34.5 g/g, respectively. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Poly(N,N‐diethylacrylamide) microspheres by dispersion polymerization

Poly(N,N‐diethylacrylamide)‐based microspheres were prepared by ammonium persulfate (APS)‐initiated and poly(vinylpyrrolidone) (PVP)‐stabilized dispersion polymerization. The effects of various polymerization parameters, including concentration of N,N′‐methylenebisacrylamide (MBAAm) crosslinker, monomer, initiator, stabilizer and polymerization temperature on their properties were elucidated. The hydrogel microspheres were described in terms of their size and size distribution and morphological and temperature‐induced swelling properties. While scanning electron microscopy was used to characterize the morphology of the microspheres, the temperature sensitivity of the microspheres was demonstrated by dynamic light scattering. The hydrodynamic particle diameter decreased sharply as the temperature reached a critical temperature ～ 30 °C. A decrease in the particle size was observed with increasing concentration of both the APS initiator and the PVP stabilizer. The microspheres crosslinked with 2–15 wt % of MBAAm had a fairly narrow size distribution. It was found that the higher the content of the crosslinking agent, the lower the swelling ratio. High concentration of the crosslinker gave unstable dispersions. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6263–6271, 2008     

Highly monodisperse crosslinked polymethylmethacrylate microparticles by dispersion polymerization

Highly monodisperse polymethylmethacrylate (PMMA) microparticles crosslinked with carboxylic group-containing urethane acrylates (CUA) were produced by simple dispersion polymerization in methanol solution. In contrast to conventional crosslinkers, the CUA employed as a crosslinker was excellent for maintaining the monodispersity of PMMA microparticles even at moderate crosslinker concentrations (to about 5 wt%). It was believed that the CUA helped form the monomer-swellable surface of primary particles, because of the structurally long tetramethylene oxide groups in the molecule. Carboxylic groups in the molecular backbone resulted in larger primary particles by increasing the solubility of the monomer mixture in the medium. Owing to these larger primary particles, the crosslinked PMMA particles showed lower polymerization rates than the linear ones during particle growth. However, at high CUA concentrations (about 10 wt%), bimodal distributions were observed. This was attributed to the high crosslinking density of the primary particle surfaces. Therefore, monomer diffusion toward the polymer phase was restricted, resulting in more favorable secondary nucleation in the medium. Received: 12 May 1998 Accepted: 19 August 1998     

Precipitation polymerization in acetonitrile and 1‐propanol mixture: synthesis of monodisperse poly(styrene‐co‐divinylbenzene) microspheres with clean and smooth surface

Precipitation polymerization of styrene (St)–divinylbenzene (DVB) has been carried out using acetonitrile/1‐propanol mixture as the reaction media and 2,2′‐azobisisobutyronitrile (AIBN) as initiator. Monodisperse micron‐sized poly(St‐co‐DVB) microspheres with clean and smooth surface were synthesized in the absence of any stabilizing agent such as surfactants or steric stabilizers. The effects of various polymerization parameters such as 1‐propanol fraction in the reaction media, initiator and total monomer concentration, DVB content, polymerization time and polymerization temperature on the morphology, particle size and size distribution were investigated. It was found that smoothly shaped stable particles were obtained when less than 70 vol% of 1‐propanol was used in the media. The particle size increased with the AIBN concentration, whereas the change of uniformity was less obvious. Monodisperse microspheres were obtained when the total monomers loading ranged from 0.5 to 3 vol%. The particle diameter ranged from 2.73 to 1.87 µm with an increasing DVB content and the uniformity was enhanced. In addition, the yield of microspheres increased with the increasing total monomer, initiator, and DVB concentration and polymerization time. Copyright © 2010 John Wiley & Sons, Ltd.     

Heterogeneous polymerization with polyaspartate macromonomer having vinyl pendant groups. II. Control of particle diameter and diameter distribution in dispersion copolymerization

To control particle diameter and particle diameter distribution in dispersion copolymerization of styrene and sodium polyaspartate macromonomer containing vinylbenzyl pendant groups, effects of some polymerization parameters, water contents, initiator concentration, styrene monomer concentration, reaction temperature, and type of initiator on the particle diameter and the diameter distribution were investigated. Variation of the water contents from 20 to 80 vol % controls the resultant particle diameter from 0.066 to 0.47 μm. The diameter increased with increasing initiator concentration. This tendency is similar to dispersion polymerization system using a nonpolymerizable stabilizer. Particle diameter distribution broadened with increasing styrene monomer concentration. This trend was attributed to the increase of a period of particle formation. This result indicated that the period of particle formation affected the resultant particle diameter distribution. Particle diameter distribution was successfully improved (CV = 9.1 from 23.6%) by shortening of decomposition time of initiator. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2281–2288, 2009     

Preparation of monodisperse poly(St‐co‐PETEA) microspheres by precipitation polymerization using ethanol as solvent

Precipitation polymerization of styrene (St) was carried out with pentaerythritol tetraacrylate (PETEA) to produce monodisperse crosslinked microspheres. A much safer ethanol replaced acetonitrile as a solvent in precipitation polymerization of monodisperse crosslinked poly(St‐co‐PETEA) microspheres. Monodisperse crosslinked microspheres with high monomer conversion were achieved within 4 hr. Uniform and well‐separated monodisperse were obtained in ethanol when PETEA concentration varied from 30 vol% to 90 vol% and the particle diameter decreased from 0.75 to 0.58 µm. The particle yield increased from 36.51 to 64.38% by increase in the initiator loading from 1 to 8 wt%. No coagulum occurred between particles when the polymerization time varied from 2 to 10 hr. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation of poly(N-isopropylmethacrylamide) latexes kinetic studies and characterization

Thermosensitive crosslinked polymer latexes have been synthesized by precipitation polymerization of N-isopropylmethacrylamide (NIPMAM) as a main monomer, methylene bis-acrylamide (MBA) as a crosslinker, and potassium persulfate (KPS) as the initiator. Polymerizations kinetics were first investigated by studying both the influence of crosslinker (MBA) and initiator (KPS) concentrations and temperature effects on the polymerization conversion, the particle size, and water-soluble polymer (WSP) as a function of time. Particle size analysis by Scanning Electron Microscopy (SEM) showed that a short nucleation step afforded the synthesis of highly monodispersed latexes. In addition, a strong dependence of WSP formation on MBA and KPS concentration and polymerization temperature was found, as well. Comparison of particle size by SEM and quasielastic light scattering clearly evidenced the dramatic effect of temperature on particle size. Lower critical solubility temperatures (LCST) of latexes were determined and compared. Finally, based on these results, the mechanism of particle formation in this polymerization process is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1823–1837, 1999     

粒径可控的聚乙烯醇交联微球VA/DVB的制备

以醋酸乙烯酯(VAc)为主单体,二乙烯基苯(DVB)为交联剂,聚乙烯醇(PVA)为分散剂,采用悬浮聚合法制备了交联微球VAe/DVB.重点考察了分散剂用量、搅拌速率、油水两相比例、NaCl用量等因素对交联微球的形成及其粒度的影响.使用甲醇对微球VAc/DVB进行醇解反应,制得了聚乙烯醇交联微球VA/DVB.结果表明:交联微球VA/DVB的物理形态决定于前驱体微球VAc/DVB的形貌与粒径.在悬浮聚合体系中,分散剂用量、搅拌速率与油水两相比是影响交联微球制备的主要因素,当分散剂用量太少(<0.3%)、搅拌速率太慢(<200 r/min)与油水两相体积比太大(>l:4)时,共聚合体系中均不能发生成球过程.控制悬浮聚合的反应条件,可以制备出球形度好、粒径可调控的交联微球VA/DVB.影响醇解反应的主要因素是反应温度,适宜的温度是40℃,反应15 h醇解度可达92%.     

Synthesis of hollow crosslinked miktoarm polymer using miniemulsion as templates

Hollow crosslinked polymers (HCPs) were synthesized using arm first method via atom transfer radical polymerization. The polymerization process was performed in miniemulsion system, in which the macroinitiator, PEG‐Br, was in the water phase, whereas the vinyl‐monomer, 4‐vinylpyridine (4VP), and the crosslinker, DVB, were in the butanone phase. TEM images and light scattering characterization showed that the resultant polymer contained a hollow space, and the volume of the hollow space could be adjusted by changing the ratio of water to butanone. Also, hollow crosslinked Miktoarm polymers (HCMPs) were synthesized through this method when two different macroinitiators, PEG‐Br and PNIPAM‐Br, were used to coinitiate the polymerization of the vinyl‐monomer, 4VP and DVB. The ¹H NMR spectra showed that the hollow polymers contained both PEG arms and PNIPAM arms. The hollow morphologies of the resultant Miktoarm polymers were the same as the HCPs. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1651–1660, 2009     

Phosphate‐Loaded Hydrogel Nanoparticles for Sepsis Prevention Prepared via Inverse Miniemulsion Polymerization

Local depletion of intestinal phosphate triggers changes in bacterial phenotypes that adversely affect the health of the host. This article describes a process for encapsulating phosphates in crosslinked poly(ethylene glycol) diacrylate (PEGDA) nanoparticles using inverse miniemulsion polymerization as a drug delivery approach for sustained release of phosphates to the intestinal epithelium. The effects of crosslinker, PEGDA co‐monomer, N‐vinyl pyrrolidone, (NVP) and surfactant concentrations on the nanoparticle size distribution, swelling ratio and monomer conversion are investigated. Increased surfactant and PEGDA concentrations result in smaller particle size and swelling ratio. A copolymerization model of crosslinking is used to predict conversion and gelation dynamics as a function of polymerization conditions. The model assumes that bulk polymerization can be used to approximate inverse miniemulsion polymerization with an aqueous‐phase initiator. The initiator efficiency is used as an adjustable parameter to simulate the conversion dynamics, thus accounting for radical confinement effects and interaction with emulsifier molecules.     

Highly crosslinked micron-range polymer microspheres by dispersion polymerization of divinylbenzene

Narrow disperse microparticles are formed by dispersion polymerization of commercial divinylbenzene in acetonitrile or ethanol solution in the presence of 2,2′-azobis(2-methylpropionitrile) initiator and polyvinylpyrrolidone stabilizer. The particles have average diameters between 1 and 9 μm depending on monomer concentration, solvent, and temperature. While the smaller particles are relatively smooth, surface texture increases with diameter to give popcorn shapes at 9 μm diameter. High crosslinker concentration is shown to be essential for particle formation. © 1993 John Wiley & Sons, Inc.     

Stabilizer-free precipitation copolymerization of renewable bio-based α-methylene-γ-butyrolactone and styrene

Stabilizer-free precipitation copolymerization of α-methylene-γ-butyrolactone (MBL) and styrene (St) was carried out in isoamyl acetate with BPO as initiator at 80°C. The influence of monomer feed ratio, initiator concentration and reaction time on the size and morphology of the obtained polymer particle was investigated in details. It was found that the monomer feed ratio play an important role on the particle formation process. When the monomer feed ratio of MBL to St was 1:2, narrow size distributed spherical polymer particles were formed with number average diameters in the range of 785–2620 nm. The formation process of polymer particle was studied to get a deep insight into the polymerization process of this reaction system. It was found that the formation mechanism of the poly(MBL-co-St) particles was similar to that of conventional precipitation polymerization. After a short nucleation stage (10 min), the amount of polymer particles remained constant and the particle growth mainly came from the capturing of newly formed polymer chains. The chemical composition and thermal property of the poly(MBL-co-St) were fully characterized by FTIR, ¹H-NMR spectra, and DSC.     

交联苯乙烯/丙烯酰胺共聚微球的制备及其C_(60)功能化初探

以二乙烯基苯 (DVB)为交联剂 ,利用一次投料分散共聚合的方法合成了交联的苯乙烯 (St) /丙烯酰胺 (Am )共聚微球 .实验发现 ,共聚单体Am的投料量和介质的极性对微球的形态有着显著的影响 .在反应过程中交联PS链段和PAm链段发生相分离 ,使粒子产生异形 .随后 ,通过微球上的酰胺基团与C60 的反应 ,将C60 引入微球表面 .初步的光电导性能测试表明 ,带有C60 的微球具有较好的光电导性能     

分散共聚合制备PSt-AA-EGDMA功能性单分散微米级交联微球的研究

以苯乙烯(St)为主单体,丙烯酸(AA)为功能单体,乙二醇二甲基双丙烯酸酯(EGDMA)为交联单体,聚乙烯吡咯烷酮(PVP)为稳定剂,偶氮二异丁腈(AIBN)为引发剂,乙醇/水混合溶剂为分散介质,用分散聚合法一步合成了功能性单分散大粒径(10～20μm)交联聚苯乙烯微球.研究了PSt-AA-EGDMA三元分散共聚合体系的动力学,由转化率-时间关联得到动力学方程;R_p=k[I]^0.13([St]^1.87+[AA]^0.13+[EGDMA]^0.2)·(1+[PVP]^0.2)exp(-E/RT).详细讨论了AA,EGDMA,PVP的浓度和溶剂极性对羧基分布的影响,阐述了AA和EGDMA对粒子形态、粒径及粒径分布的影响.     

Synthesis of narrowly distributed polystyrene-encapsulated silica nanoparticles via emulsion polymerization

Polystyrene (PS)-encapsulated silica nanoparticles were successfully synthesized by conventional emulsion polymerization for solving the aggregation matter of nanoscaled silica. The grafting coupling agents and PS on the silica surface were detected by Fourier Transform Infrared (FTIR) spectroscopy. The influence of silica and monomer to water ratios and initiator concentration on particle size distribution of the nanocomposite latex was investigated. The particle size distribution firstly narrowed and then broadened with the increase of silica and monomer to water ratios and initiator concentration. The narrow distribution could be controlled in an appropriate silica and monomer to water ratio and an initiator concentration of 1/15 and 2 wt%, respectively. From the evaluation of transmission electron microscopy (TEM) micrographs and dynamic light scattering (DLS) measurement, it was proved that the nanocomposite latex did not have all sphere-like shape, but contained tiny amounts of irregular bodies. The formation mechanism of PS-encapsulated silica nanoparticles was also discussed.     

蒸馏沉淀聚合过程中交联度对单分散聚合物微球形成的影响书

以苯乙烯为单体、二乙烯基苯（DVB）为交联剂，过氧化二苯甲酰（BPO）为引发剂研究了蒸馏沉淀聚合法制备聚合物微球过程中交联单体二乙烯苯的用量对单分散聚合物微球成球的影响。结果表明，增加二乙烯基苯的比例，即提高交联度有利于形成单分散的聚合物微球。