Surface functionalization with phosphazene substrates—part VII. Silicon‐based materials functionalized with hexachlorocyclophosphazene

This paper investigates by means of XPS analysis the surface functionalization of soda‐lime and fused quartz glass substrates with hexachlorocyclophosphazene (HCCP), obtained by simple immersion in solutions of phosphazene in anhydrous solvents. Several experimental parameters like reaction solvent, temperature and treatment duration were studied, together with the influence of physisorbed water on the surface of the substrates. Phosphazene‐derived deposits resistant to tetrahydrofuran (THF) washing and vacuum drying were obtained. They presented P:N:Cl stoichiometric ratios close to 1:1:1 when the reaction and the final drying of the samples were performed at room temperature; use of higher temperatures resulted in lower nitrogen and chlorine content. The chemical nature of the films was studied by XPS peaks deconvolution which enabled us to propose a possible, temperature‐enhanced hydrolytical degradation mechanism. Copyright © 2008 John Wiley & Sons, Ltd.     

Surface analysis of the solid electrolyte interface formed by additives on graphite electrodes in Li‐ion batteries using XPS,FE‐AES,and XHR‐SEM techniques

We investigate the formation and distribution of the solid electrolyte interface (SEI) layer on a graphite anode with two additives [vinylethylene carbonate (VEC) and vinylene carbonate (VC)] in a formation process using XPS, field emission AES, and extreme high‐resolution SEM (XHR‐SEM) techniques, and we studied what factors play an important role in determining the formation of the SEI layer. The VEC‐derived SEI behaviors (morphology, thickness, compound, and balance over electrode position) on a graphite anode largely depend on the elevated temperature. The VC‐derived SEI layer is mostly formed in the initial charging step, showing simple growth (formation) behavior. It is suggested that the properties of the additives are important for SEI bonding configurations at the nanoscale film surface, and to achieve the stable SEI layer, there appears to be an effective formation process for the additive properties. This research highlights the challenges of developing a stable SEI layer with additives in the formation process for electric vehicle batteries and would make a contribution to the understanding of how formation conditions affect an SEI layer with respect to additive properties. Copyright © 2014 John Wiley & Sons, Ltd.     

Optimization of cryo‐XPS analyses for the study of thin films of a block copolymer (PS‐PEO)

The water‐induced surface reorganization of a thin film of a block copolymer [polystyrene‐b‐poly(ethylene oxide), PS‐PEO], was studied by cryogenic X‐ray photoelectron spectroscopy (cryo‐XPS). Experimental parameters were examined with a view to optimize the analysis. The absence of artifacts due to the low temperature of analysis was checked, and the influence of the procedure used for sample hydration before analysis was investigated. Adequate timing of the different steps of the analysis and temperature program was also established. With this optimized protocol, an important reorganization of the block copolymer was detected, showing more pronounced exposure of the PEO block at the outermost surface in hydrated compared to dry environment. As this type of polymer surface is prone to be used for biomedical applications, an accurate knowledge of the chemical composition of the outermost surface in aqueous environments is crucial. The development of this technique is therefore promising for related systems. Copyright © 2011 John Wiley & Sons, Ltd.     

In‐depth diffusion of oxygen into LDPE exposed to an Ar–O2 atmospheric post‐discharge: a complementary approach between AR‐XPS and Tof‐SIMS techniques

The in‐depth oxygen diffusion into a low density polyethylene film is performed in the post‐discharge of an atmospheric plasma torch, supplied in argon as carrier gas and with or without oxygen as reactive gas. The chemical and structural properties of the polymer surface and bulk are studied in terms of plasma parameters (treatment time, power, and reactive gas flow rate). A good correlation between XPS and Fourier transform infrared spectroscopy analyses is demonstrated. The penetration depth of oxygen into the bulk of the polymer is investigated by angle resolved‐XPS and time‐of‐flight SIMS. It is shown that, depending on the plasma conditions, oxygen could penetrate up to 20–40 nm into the low density polyethylene during the atmospheric plasma treatment. Copyright © 2014 John Wiley & Sons, Ltd.     

The distribution of hydroxyl ions at the surface of anodic alumina

Barrier‐type anodic films 3–15 nm thick have been formed on electropolished 99.999% aluminium. Variable‐angle XPS has been used to identify a significant proportion of hydroxyl ions at the surface of the relatively compact alumina films. The location of an oxygen‐rich region at the outer surface of the oxide has been confirmed by medium‐energy ion scattering (MEIS). Combining the information from these two techniques leads to the conclusion that a hydroxyl‐containing surface region is responsible for this oxygen‐rich surface layer, MEIS revealing an approximately linear relationship between the total oxide thickness and the thickness of the hydroxyl‐rich surface region. From consideration of the mechanisms of amorphous alumina formation by ionic transport, with incorporation of electrolyte‐derived species into the thickening film, the generation of the hydroxyl‐rich outermost region is considered to result from the formation of gel‐like material at the film/electrolyte interface. Copyright © 2003 John Wiley & Sons, Ltd.     

Surface properties of polypropylene following a novel industrial surface‐treatment process

Polypropylene (PP) is used in many automotive applications where good paint adhesion is of primary importance. PP is widely known for its low surface energy which impacts negatively on its adhesion strength. PP surfaces were modified using a new industrial surface‐treatment process known as the Accelerated Thermo‐molecular adhesion Process (ATmaP). ATmaP grafts functional groups to the polymer surface derived from an atomised and vapourised nitrogen‐containing coupling agent. The surface properties and adhesion performance of PP samples treated using the ATmaP process and two different flame processes were compared using XPS, time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) and mechanical testing (pull‐up tests). The latter showed that ATmaP improved adhesion strength significantly in comparison with conventional flame treatments. XPS showed an increase in oxygen and nitrogen concentration on the surface of ATmaP‐treated samples compared with untreated and flame‐treated samples. Principal components analysis (PCA) of the ToF‐SIMS data revealed the major phenomena occurring during the surface treatment of PP samples. Early stage events, including the chain scission of the PP backbone chain and the subsequent reaction of these chains with the surrounding air, are captured by the first principal component (PC1). The increase in the concentration of NO surface functional groups resulting from ATmaP treatment is captured by the second principal component (PC2). Copyright © 2008 John Wiley & Sons, Ltd.     

Monte‐Carlo simulation of x‐ray photoelectron emission from silver

Silver 3d x‐ray photoelectron spectroscopy (XPS) spectra were simulated with the Monte‐Carlo method using an effective energy‐loss function that was derived from a reflected electron energy‐loss spectroscopy (REELS) analysis based on an extended Landau approach. After confirming that Monte‐Carlo simulation based on the use of the effective energy‐loss function can successfully describe the experimental REELS spectrum and Ag 3d XPS spectrum, we applied Monte‐Carlo simulation to predict the angular distribution of Ag 3d x‐ray photoelectrons for different x‐ray incidence angles and different photoelectron take‐off angles. The experimental photoelectron emission microscope that we are constructing was confirmed as being close to the optimum configuration, in which the x‐ray incident angle as measured from the surface normal direction is 74° and the photoelectron take‐off angle is set normal to the surface. The depth distribution functions of the Ag 3d X‐ray photoelectrons for different energy windows suggest that the photoelectron emission microscope will exhibit greater surface sensitivity for narrower photoelectron energy windows. Copyright © 2003 John Wiley & Sons, Ltd.     

Summary of ISO/TC 201 Standard: ISO 16129‐:2012 – Surface chemical analysis — Procedures to assess the day‐to‐day performance of an X‐ray photoelectron spectrometer

This International Standard is designed to allow the user to simply assess, on a routine basis, several key parameters of an X‐ray photoelectron spectrometer. It is not intended to provide an exhaustive performance check but instead provides a rapid set of tests that may be conducted frequently. Aspects of instrument behaviour covered by this document include the vacuum, measurements of spectra of conductive or non‐conductive samples and the current state of the X‐ray source. Other important aspects of the instrument performance (e.g. lateral resolution) fall outside the scope of this standard. The standard is intended for use with commercial X‐ray photoelectron spectrometers equipped with a monochromated Al Kα X‐ray source or with a unmonochromated Al or Mg Kα X‐ray source. Copyright © 2012 John Wiley & Sons, Ltd.     

Surface characterization of pre‐formed alginate fibres incorporated with a protein by a novel entrapment process

A novel physical entrapment process has been explored as an approach to surface incorporation of proteins within pre‐formed alginate fibres under mild conditions. Entrapment of the protein of choice was achieved by exposing the alginate fibres to a Na⁺‐rich NaCl/CaCl₂ mixture solution, which caused the formation of a moderate dissociation layer into which the protein could diffuse. Subsequent addition of a large excess of multi‐valent cations led to the collapse of the surface and entrapment of the protein within the surface. Bovine serum albumin (BSA) was used as a model protein to investigate the effect of process parameters on the entrapment efficiency. Scanning electron microscopy revealed that there was an increase in the surface roughness and a slight increase in the average diameter of the fibres after protein entrapment. The presence of the protein at the surface of alginates after the entrapment process was confirmed by means of confocal laser‐scanning microscopy, X‐ray photoelectron spectroscopy (XPS) and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS). The ion exchanges at the surface were evident, as detected by XPS and ToF‐SIMS. It was found that under fixed pre‐swelling conditions, the entrapment efficiency increased with increasing treatment time and, particularly, with protein concentration in the exposure solution. Copyright © 2005 John Wiley & Sons, Ltd.     

Effects of elastic scattering and analyzer‐acceptance angle on the analysis of angle‐resolved X‐ray photoelectron spectroscopy data

We have made calculations of N 1s, O 1s, Si(oxide) 2p, Hf 4f, and Si(substrate) 2p photoelectron intensities at selected emission angles for films of SiO_1.6N_0.4 and HfO_1.9N_0.1 of various thicknesses on silicon. These calculations were made with the National Institute of Standards and Technology (NIST) Database for Simulation of Electron Spectra for Surface Analysis (SESSA) to investigate effects of elastic scattering and analyzer‐acceptance angle that could be relevant in the analysis of angle‐resolved X‐ray photoelectron spectroscopy (ARXPS) experiments. The simulations were made for an XPS configuration with a fixed angle between the X‐ray source (i.e. for the sample‐tilting mode of ARXPS) and with Al and Cu Kα X‐ray sources. The no‐loss intensities changed appreciably as elastic scattering was switched ‘on’ and ‘off’, but changing the analyzer‐acceptance angle had a smaller effect. Ratios of intensities for each line from the overlayer film for the least realistic model condition (elastic scattering switched ‘off’, small analyzer‐acceptance angle) to those from the most realistic model condition (elastic scattering switched ‘on’, finite analyzer‐acceptance angle) changed relatively slowly with emission angle, but the corresponding intensity ratio for the Si(substrate) 2p line changed appreciably with emission angle. The latter changes, in particular, indicate that neglect of elastic‐scattering effects can lead to erroneous results in the analysis of measured ARXPS data. The elastic‐scattering effects were larger in HfO_1.9N_0.1 than in SiO_1.6N_0.4 (due to the larger average atomic number in the former compound) and were larger with the Al Kα X‐ray source than with the Cu Kα source because of the larger cross sections for elastic scattering at the lower photoelectron energies. Copyright © 2010 John Wiley & Sons, Ltd.     

Numerical approximation of AR‐XPS spectra for rough surfaces considering the effect of electron shadowing

A computational scheme is presented that takes into account the topography, i.e. the shadowing and hence the local emission angle of the electrons when evaluating AR‐XPS data of macroscopic rough surfaces. The topography of the sample surface is supposed to be recorded by atomic force microscopy and/or optical microscopy. The emitted photoelectrons are simulated based on an extension of the Beer–Lambert law that includes the shadowing, the current local emission angle, and the geometrical instrument setup. The obtained angle‐resolved XPS spectra are optimized in accordance with experimental ones via a self‐consistent minimization algorithm that also allows one to determine the layer thicknesses of the corrugated sample. In order to validate the proposed numerical scheme, the simulation program simulation of electron spectra for surface analysis is used. An additional analysis is then performed considering only experimental data. The numerical scheme gives good agreement in simulation–simulation as well as simulation–experiment comparisons and permits a comprehensible interpretation of the measured data. Copyright © 2014 John Wiley & Sons, Ltd.     

Extracting information on the surface monomer unit distribution of PLGA by ToF‐SIMS

The surface chemistry of a range of random poly l‐lactide‐co‐glycolide (PLGA) materials has been investigated using XPS, static secondary ion mass spectrometry (SSIMS) and gentle secondary ion mass spectrometry (G‐SIMS). The estimated mole fraction of lactide units provided by SSIMS was in good agreement with bulk composition and appeared not to have been affected by contamination. Conversely, XPS assessment of lactide compositions was unreliable due to hydrocarbon contamination contributions. In this study, we propose a novel model to demonstrate that by using SSIMS it is possible to infer the degree of trans‐esterification for PLGA co‐polymers synthesised from a mixture of lactide and glycolide homo‐dimers. This was determined by introducing two independent parameters, the ratio of trans‐esterified bonds to the total number of ester bonds, P_T, and the lactide composition. The model has indicated that, for this set of polymers, P_T was approximately 0.25. Furthermore, we have demonstrated that G‐SIMS successfully identified the structurally important key fragments leading to direct identification. Analysis by G‐SIMS showed that the glycolic acid units from all PLGA compositions are emitted in a lower energy‐fragmentation process than lactic acid units. Copyright © 2008 John Wiley & Sons, Ltd.     

Cryo‐XPS study of xanthate adsorption on pyrite

The adsorption of xanthate on pyrite has been extensively studied. However, the adsorption mechanisms remain a subject of controversy. Formation of both dixanthogen and metal‐xanthate complexes has been suggested. In this study, both room temperature X‐ray photoelectron spectroscopy (XPS) (RT‐XPS) and liquid nitrogen temperature XPS (Cryo‐XPS) were used to study interactions between pyrite and xanthate. While dixanthogen was not detected by RT‐XPS, it was successfully identified through C1s and S 2p peaks using Cryo‐XPS. The impact of pH and copper activation on adsorption of xanthate on pyrite was also investigated. It was found that at low pH, dixanthogen is the dominant species of xanthate adsorption on pyrite. At high pH, metal‐xanthate complexes were found to be prevalent on pyrite surfaces, which are responsible for the surface hydrophobicity. Copper activation showed a significant effect on xanthate adsorption on Cu‐activated pyrite, resulting in mostly the formation of Cu‐xanthate complexes rather than dixanthogen, mainly in the form of Cu(I)‐isopropyl xanthate complex (CuIPX). Copyright © 2012 John Wiley & Sons, Ltd.     

Quantitative analysis of an organic thin film by XPS,AFM and FT‐IR

We report the characterization of Firpic (iridium(III)bis[4,6‐di‐fluorophenyl]‐pyridinato‐N,C²,]picolinate) organic thin film prepared by vacuum deposition to provide a systematic route to organic film quantification. To analyze the characteristics of thin Firpic films on a Si substrate, various techniques such as XPS, Fourier transform infra‐red (FT‐IR) spectrometer, and atomic force microscopy (AFM) are utilized. The Firpic films remain stable without surface morphological or compositional change during deposition and after exposure to X‐ray irradiation or atmospheric environment, for which qualities these films are believed to be an ideal platform as a pure organic thin film. The monotonic increases in FT‐IR and XPS intensities with film thickness are matching well with each other. In particular, from the XPS intensity analysis, the relative atomic sensitivity factors of the present system, electron attenuation length, and molecular density in the organic thin film can be evaluated. Copyright © 2011 John Wiley & Sons, Ltd.     

Analysis of oxidation behavior under dry air of neat and Ta‐alloyed furan‐resin‐derived carbons heat treated at 3000 °C

Oxidation behavior and structural changes of furan‐resin‐derived carbons heat treated at 3000 °C were investigated at 500 and 700 °C under dry air. Thermogravimetric analysis (TGA), Raman spectroscopy and X‐ray photoelectron spectroscopy (XPS) were employed to detect and understand this behavior and the changes. Effect of tantalum on antioxidation property of Ta‐alloyed carbon was also analyzed. The neat and Ta‐alloyed carbons had insignificant weight losses even after being kept at 500 °C for 12 h, while the Ta‐alloyed carbon had weight loss lower than that of the neat carbon after being kept at 700 °C for 6 h. It has been found by XPS that oxidation involves oxygen in internal area as well as on external surface of the carbons. It was also inferred that the carbon stored with oxygen in deeper internal area was easily oxidized. Ta alloying leads to change of the state of the Fermi energy on the specimens, which may cause the antioxidation property. Copyright © 2005 John Wiley & Sons, Ltd.     

A two‐stage surface treatment for the long‐term stability of hydrophilic SU‐8

The use of SU‐8 photoresist as a structuring material for portable capillary‐flow cytometry devices has been restricted by the near‐hydrophobic nature of the SU‐8 surface. In this work, we evaluate the use of chemical and plasma treatments to render the SU‐8 surface hydrophilic and characterise the resulting surface utilising a combination of techniques including contact angle goniometry, atomic force microscopy and X‐ray photoelectron spectroscopy. In particular, for low‐power plasma treatments, we find that the chemistry of the plasma used to modify the SU‐8 surface and the incorporation of O₂ on that modified surface are paramount for improved surface wettability, whilst plasma‐induced surface roughness is not a necessary requirement. We demonstrate a technique to obtain a hydrophilic SU‐8 surface with contact angle as low as 7° whilst controlling and significantly reducing the level of surface roughness generated via the applied plasma. An additional chemical treatment step is found to be essential to stabilise the activated SU‐8 surface, and incubation of the samples with ethanolamine is demonstrated as an effective second‐stage treatment. Application of the optimised two‐stage surface treatment to cross‐linked SU‐8 is shown to result in a smooth hydrophilic surface that remains stable for over 3 months. Copyright © 2015 The Authors Surface and Interface Analysis Published by John Wiley & Sons Ltd.     

Kinetics and Mechanism of Oxidation of 1‐Methoxy‐2‐propanol and 1‐Ethoxy‐2‐propanol by Ditelluratocuprate(III) in Alkaline Medium

The kinetics of oxidation of 1‐methoxy‐2‐propanol and 1‐ethoxy‐2‐propanol by ditelluratocuprate(III) (DTC) in alkaline liquids has been studied spectrophotometrically in the temperature range of 293.2–313.2 K. The reaction rate showed first order dependence in DTC and fractional order with respect to 1‐methoxy‐2‐propanol or 1‐ethoxy‐2‐propanol. It was found that the pseudo‐first order rate constant k_obs increased with an increase in concentration of OH^? and a decrease in concentration of TeO₄^2?. There is a negative salt effect. A plausible mechanism involving a pre‐equilibrium of a adduct formation between the complex and 1‐methoxy‐2‐propanol or 1‐ethoxy‐2‐propanol was proposed. The rate equations derived from mechanism can explain all experimental observations. The activation parameters along with the rate constants of the rate‐determining step were calculated.     

QuickFF: A program for a quick and easy derivation of force fields for metal‐organic frameworks from ab initio input

QuickFF is a software package to derive accurate force fields for isolated and complex molecular systems in a quick and easy manner. Apart from its general applicability, the program has been designed to generate force fields for metal‐organic frameworks in an automated fashion. The force field parameters for the covalent interaction are derived from ab initio data. The mathematical expression of the covalent energy is kept simple to ensure robustness and to avoid fitting deficiencies as much as possible. The user needs to produce an equilibrium structure and a Hessian matrix for one or more building units. Afterward, a force field is generated for the system using a three‐step method implemented in QuickFF. The first two steps of the methodology are designed to minimize correlations among the force field parameters. In the last step, the parameters are refined by imposing the force field parameters to reproduce the ab initio Hessian matrix in Cartesian coordinate space as accurate as possible. The method is applied on a set of 1000 organic molecules to show the easiness of the software protocol. To illustrate its application to metal‐organic frameworks (MOFs), QuickFF is used to determine force fields for MIL‐53(Al) and MOF‐5. For both materials, accurate force fields were already generated in literature but they requested a lot of manual interventions. QuickFF is a tool that can easily be used by anyone with a basic knowledge of performing ab initio calculations. As a result, accurate force fields are generated with minimal effort. © 2015 Wiley Periodicals, Inc.