Separation of gold, palladium and platinum from metallurgical samples using an amberlite XAD-7 resin column prior to their atomic absorption spectrometric determinations.

A simple and sensitive method for the separation and preconcentration of gold, palladium and platinum has been established prior to their atomic absorption spectrometric determinations. Analytes from 0.5 mol dm(-3) KI in a 2 mol dm(-3) HCl solution were recovered using an Amberlite XAD-7 column as halogeno complexes. The effects of some analytical parameters, including reagent amounts, sample volume and flow rates, on the quantitative recoveries of gold, palladium and platinum were investigated. The influences of some diverse ions were also studied. The proposed method has been applied for the preconcentration and separation of analytes from pure copper and anodic slime samples with satisfactory results (recoveries > 95%, relative standard deviations < 9.0%, relative error < or = 5%).     

Amberlite XAD resin solid-phase extraction coupled on-line to a flow injection approach for the rapid enrichment and determination of phenols in water and waste waters

A novel and expeditious approach for direct determination of phenols in water and waste waters based on solid-phase extraction coupled on-line to a flow injection analysis (FIA) manifold is described. The method employs on-line preconcentration of the phenols in an acidified sample (pH=2.0) onto a 3 cmx3 mm column packed with Amberlite XAD-4 resin. The phenols are subsequently eluted from the resin into a flowing system with an alkaline solution (pH=13) by actuating a switching valve; the eluted analytes were then quantified spectrophotometrically as the products of reaction with 4-aminoantipyrine (4-AAP) and potassium ferricyanide on passing through the flow-cell of a detector. The proposed method has a linear calibration range 0.01-1 mug ml(-1) of phenol, with a detection limit of 0.004 mug ml(-1) (S/N=3) and a sample throughput of 12 h(-1), investigated with a 4.4 ml sample volume. The relative standard deviation is 2.4% for 0.2 mug ml(-1) of the analyte. The sensitivity offered by the procedure was higher by a factor of 13 than that provided by a conventional flow injection analysis method. The analytical scheme of the proposed system is much simpler than its conventional manual counterpart due to the fact that it combines trace enrichment, sample clean-up, derivation and detection in one analytical set-up. The high speed, ease of use and automation, selectivity, and relative freedom from random contamination by sample handling make this method ideal for the phenols monitoring in water and waste waters.     

Flame atomic absorption spectrometric determination of silver after preconcentration on Amberlite XAD-16 resin from thiocyanate solution

A method of silver preconcentration by using a column containing Amberlite XAD-16 resin and this future determination by a flame AAS after elution is proposed. The effect of the factors such as pH, the nature of complexing agent, sample volume, flow rate, the type and concentration of elution solution on the preconcentration efficiency have been investigated. The influence of some matrix elements on the recovery of silver were also examined. It was found, that the quantitative recovery of thiocyanate complex of silver was obtained from nitric acid solution (pH 2) as 99.20+/-0.07% at the 95% confidence level. A preconcentration factor up to 75 could be obtained. The detection limit of silver was 0.047 mg l(-1). The adsorption of silver onto Amberlite XAD-16 can be formally described by a Langmuir equation with maximum adsorption capacity 4.66 mg g(-1) (0.043 mmol g(-1)). The proposed method was applied to determination of silver in standard alloy with relative error 6.25%.     

Speciation of Cr(III) and Cr(VI) in water after preconcentration of its 1,5-diphenylcarbazone complex on amberlite XAD-16 resin and determination by FAAS

A simple and sensitive method for the speciation, separation and preconcentration of Cr(VI) and Cr(III) in tap water was developed. Cr(VI) has been separated from Cr(III) and preconcentrated as its 1,5-diphenylcarbazone complex by using a column containing Amberlite XAD-16 resin and determined by FAAS. Total chromium has also been determined by FAAS after conversion of Cr(III) to Cr(VI) by oxidation with KMnO₄. Then, Cr(III) has been calculated by subtracting Cr(VI) from the total. The effect of acidity, amount of adsorbent, eluent type and flow rate of the sample solution on to the preconcentration procedure has been investigated. The retained Cr(VI) complex was eluated with 10 ml of 0.05 mol l⁻¹ H₂SO₄ solution in methanol. The recovery of Cr(VI) was 99.7±0.7 at 95% confidence level. The highest preconcentration factor was 25 for a 250 ml sample volume. The detection limit of Cr(VI) was found as 45 μg l⁻¹. The adsorption capacity of the resin was found as 0.4 mg g⁻¹ for Cr (VI). The effect of interfering ions has also been studied. The proposed method was applied to tap water samples and chromium species have been determined with the relative error <3%.     

A novel method for the simultaneous determination of Pb (II), Cd (II) and Zn (II) in environmental water samples

A novel UV-VIS spectrophotometric method was developed in this study by using solid phase extraction procedure for the simultaneous preconcentration, separation and determination of trace levels of Pb (II), Cd (II) and Zn (II) ions in various water samples by using Amberlite N,N-bis(salicylidene)cyclohexanediamine (SCHD) resin. This study presents the results of experimental procedures carried out like the adsorption of analytes to the resin, influences of some analytical parameters that effect the recovery such as pH, sample volume, sample flow rate, eluent type and concentration, eluent volume, eluent flow rate and the effects of alkaline metals, earth alkaline metals and some other transition metals. The analytes in the samples with the adjusted pH range of 4–7 were adsorbed on XAD-4-SCHD resin and eluted by using 1.0 mol L^?1 nitric acid. The amounts of ions were determined by using UV-VIS spectrometer. The limits of detection were 0.03, 0.07 and 0.05 µg mL^?1 for Pb (II), Cd (II) and Zn (II), respectively. The accuracy of the method was assured by the analysis of the certified standard water sample NW-TMDA-70.2 and the observed recoveries were above 93%. Different environmental water samples that contain trace amounts of Pb (II), Cd (II) and Zn (II) were analysed by using the method developed in this study. Same samples were also analysed by ICP-MS for comparison and almost the similar results were observed. The method developed in this study was successfully applied to the various environmental water samples to determine the trace levels of Pb (II), Cd (II) and Zn (II) ions.     

Method for the simultaneous determination of traces of atrazine,pyrazon and lindane for monitoring potable water supplies

When groundwater reservoirs situated in agriculturally used areas are assigned as future potable water supplies, it has to be provided that traces of plant protection agents used in this area can be monitored in this groundwater. A method is described for the simultaneous quantitative determination of atrazine, pyrazon and lindane in potable water at the (sub-)ppb level. An adsorption column filled with Amberlite XAD-2 microporous resin advantageously replaces other preconcentration techniques. The concentrated eluate is analyzed by capillary gas chromatography without further purification. The recovery is 80% for atrazine and lindane at the 0.1 ppb level and 40% for pyrazon (1 ppb). The method was tested using tap water from the public water supply network. The complete procedure including sample preparation, preconcentration by adsorption on a macroporous resin, elution with diethyl ether, evaporation to dryness, addition of internal standard solution and capillary gas Chromatographic analysis is carried out in less than three hours (sample volume: 11).     

Determination of Triazine Herbicides and Metabolites by Solid Phase Extraction with HPLC Analysis

An efficient solid phase extractive preconcentration/separation method was developed for the trace determination of herbicides in aqueous samples using Amberlite XAD-4 resin as the adsorbent. The retained herbicides were eluted with methanol at a flow rate of 1.0 mL min^?1 and determined by HPLC-DAD (wavelength of 220 nm) using water (pH:4.7, phosphoric acid) and methanol (ratio 35:65) as the mobile phase with a flow rate of 1.0 mL min^?1. Quantitative recoveries of simazine, atrazine and its metabolities were achieved at optimized analysis conditions that included 0.75 g of resin; a pH of 3.0; an eluent volume of 3.0 mL; an eluent flow rate of 1.0 mL min^?1; and a sample flow rate of 4.0 mL min^?1. The limits of detection, preconcentration factor, and linear ranges for the herbicides were 0.084–0.121 µgL^?1, 1000, and 0.5–20 mg L^?1, respectively. The performance of the method was evaluated by analysis of spiked water samples. The recoveries of simazine, atrazine and their metabolities were found to be quantitative (99.6–104.8%) with RSDs of 2.2–4.8% and 2.8–4.7% for intra-day and inter-day precision, respectively. The proposed method was successfully applied for trace determination of studied analytes in waste water, apple juice, and red wine samples.     

Silica Gel Coated with Schiff's Base: Synthesis and Application as an Adsorbent for Cadmium, Copper, Zinc, and Nickel Determination after Preconcentration by Flame Atomic Absorption Spectrometry

A method for the preconcentration of Cd(II), Cu(II), Zn(II), and Ni(II) is proposed using a minicolumn filled with silica gel modified by Schiff's base. The retained analytes on the ligand-coated silica gel were recovered with a small volume of HNO₃ (nitric acid). The metal ions in the eluent were determined by flame atomic absorption spectrometer (FAAS). Different factors, including the pH of the sample solution, the sample volume, the amount of silica gel, eluent volume and matrix effects for preconcentration were examined. The recoveries for the analytes under optimum working conditions were higher than 95%. The relative standard deviations of the determination were 1.50, 2.10, 2.40, 3.43% for Cu(II), Cd(II), Zn(II) and Ni(II). The limits of detection (3s, n = 10) for Cd(II), Cu(II), Zn(II), and Ni(II) were found to be 3, 5, 5 and 4.7 ngL^–1. The proposed method was applied to the analysis of some natural water samples and standard reference aluminum alloy material (NBS SRM 85b).     

Solid-Phase Extraction and Spectrophotometric Determination of Molybdenum(VI) in Soil and Plant Samples as a Mo(V)-Thiocyanate Complex

A method for the preconcentration and determination of molybdenum(VI) in soil and plant samples using Amberlite XAD-7 resin and spectrophotometry is proposed. Molybdenum was preconcentrated as its Mo(V)-thiocyanate complex using a column containing Amberlite XAD-7 resin and determined spectrophotometrically at 461.0nm in acetone after elution. We investigated several parameters that affect the recovery of molybdenum, such as acidity, amount of reducing and complexing agents, flow rates, volume of sample solution, type and amount of eluent, and the presence of diverse ions. The limit of detection of the proposed method was 38µgL^–1 of molybdenum. The recovery of molybdenum was 98.25±0.05 at 95% confidence level. The highest preconcentration factor was 100 for 250mL of sample volume. The proposed method was applied to soil and plant samples, and molybdenum was determined with a relative error of <3.5%.     

Column solid-phase extraction with Chromosorb-102 resin and determination of trace elements in water and sediment samples by flame atomic absorption spectrometry

A column, solid-phase extraction (SPE), preconcentration method was developed for determination of Bi, Cd, Co, Cu, Fe, Ni and Pb ions in drinking water, sea water and sediment samples by flame atomic absorption spectrometry. The procedure is based on retention of analytes in the form of pyrrolidine dithiocarbamate complexes on a short column of Chromosorb-102 resin from buffered sample solution and then their elution from the resin column with acetone. Several parameters, such as pH of the sample solution, amount of Chromosorb-102 resin, amount of ligand, volume of sample and eluent, type of eluent, flow rates of sample and eluent, governing the efficiency and throughput of the method were evaluated. The effects of divers ions on the preconcentration were also investigated. The recoveries were >95%. The developed method was applied to the determination of trace metal ions in drinking water, sea water and sediment samples, with satisfactory results. The 3σ detection limits for Cd, Cu, Fe, Ni and Pb and were found to be as 0.10, 0.44, 11, 3.6, and 10 μg l⁻¹, respectively. The relative standard deviation of the determination was <10%. The procedure was validated by the analysis of a standard reference material sediment (GBW 07309) and by use of a method based on coprecipitation.     

Nickel determination in saline matrices by ICP-AES after sorption on Amberlite XAD-2 loaded with PAN

In the present paper, a solid phase extraction system for separation and preconcentration of nickel (ng g⁻¹) in saline matrices is proposed. It is based on the adsorption of nickel(II) ions onto an Amberlite XAD-2 resin loaded with 1-(2-pyridylazo)-2-naphthol (PAN) reagent. Parameters such as the pH effect on the nickel extraction, the effect of flow rate and sample volume on the extraction, the sorption capacity of the loaded resin, the nickel desorption from the resin and the analytical characteristics of the procedure were studied. The results demonstrate that nickel(II) ions, in the concentration range 0.10–275 μg l⁻¹, and pH 6.0–11.5, contained in a sample volume of 25–250 ml, can be extracted by using 1 g Amberlite XAD-2 resin loaded with PAN reagent. The adsorbed nickel was eluted from the resin by using 5 ml 1 M hydrochloric acid solution. The extractor system has a sorption capacity of 1.87 μmol nickel per g of Amberlite XAD-2 resin loaded with PAN. The precision of the method, evaluated as the R.S.D. obtained after analyzing a series of seven replicates, was 3.9% for nickel in a concentration of 0.20 μg ml⁻¹. The proposed procedure was used for nickel determination in alkaline salts of analytical grade and table salt, using an inductively coupled plasma atomic emission spectroscopy technique (ICP-AES). The standard addition technique was used and the recoveries obtained revealed that the proposed procedure shows good accuracy.     

Use of Escherichia coli immobilized on amberlite XAD-4 as a solid-phase extractor for metal preconcentration and determination by atomic absorption spectrometry.

A sensitive solid-phase extraction technique (SPE) for the enrichment of Fe(III), Co(II), Mn(II) and Cr(III) prior to atomic absorption spectrometric analysis is described. Escherichia coli immobilized on Amberlite XAD-4 was used as a solid-phase extractor. The effects of the pH, amount of solid-phase, eluent type and volume of the sample solution on the recovery of the metal ions were investigated. The effect of diverse ions was also investigated. The recoveries of Fe(III), Co(II), Mn(II) and Cr(III) under the optimum conditions were found to be 99 +/- 2, 99 +/- 3, 98 +/- 2, 98 +/- 3%, respectively, at the 95% confidence level. The detection limits of the metal ions were found as to be 2.4, 3.8, 1.3 and 1.7 ng ml(-1) for Fe(II), Co(II), Mn(II) and Cr(III) respectively, by applying a preconcentration factor of 25. The proposed enrichment method was applied to the determination of analytes in Atatürk Dam water samples, and alloy samples (RSD < 5%). The accuracy of the method was verified on certified alloy samples (NBS SRM 85b and NBS SRM 59a). The analytes were determined with a relative error lower than 5% in water and alloy samples.     

Determination of copper(II) in various samples by flame atomic absorption spectrophotometry after column preconcentration onto pulverized Amberlite XAD-4 loaded with N-benzoylphenylhydroxylamine

A sensitive technique for the determination of trace Cu(II) in various samples after column preconcentration by adsorbing onto pulverized Amberlite XAD-4 loaded with N-benzoylphenylhydroxylamine (BPHA) was developed. Several experimental conditions, such as the size of XAD-4, adsorption flow rate, pH of sample solution, and so forth, were optimized. The interfering effects of diverse concomitant ions were investigated. Al(III), Fe(III), Ni(II), and Co(II) interfered, but the interference by these ions was completely eliminated by adjusting the amount of XAD-4-BPHA resin to 0.30 g. The dynamic range, the correlation coefficient (R₂), and the detection limit obtained by the proposed technique were 1.0–60, 0.9953, and 0.83 ng/mL, respectively. For validating the technique, the aqueous samples (stream water, reservoir water, and wastewater), the diluted brass sample, and the plastic sample were used as real samples. Recovery yields of 94–102% were obtained. These measured data were not different from ICP-MS data at the 95% confidence level. This method was also validated by rice flour CRM (normal, fortified) samples. Based on the results of the experiment, it has been found that the proposed technique can be applied to the determination of Cu(II) in various real samples. The text was submitted by the authors in English.     

Ionic liquid-based microwave-assisted dispersive liquid-liquid microextraction and derivatization of sulfonamides in river water, honey, milk, and animal plasma

The ionic liquid-based microwave-assisted dispersive liquid-liquid microextraction (IL-based MADLLME) and derivatization was applied for the pretreatment of six sulfonamides (SAs) prior to the determination by high-performance liquid chromatography (HPLC). By adding methanol (disperser), fluorescamine solution (derivatization reagent) and ionic liquid (extraction solvent) into sample, extraction, derivatization, and preconcentration were continuously performed. Several experimental parameters, such as the type and volume of extraction solvent, the type and volume of disperser, amount of derivatization reagent, microwave power, microwave irradiation time, pH of sample solution, and ionic strength were investigated and optimized. When the microwave power was 240 W, the analytes could be derivatized and extracted simultaneously within 90 s. The proposed method was applied to the analysis of river water, honey, milk, and pig plasma samples, and the recoveries of analytes obtained were in the range of 95.0-110.8, 95.4-106.3, 95.0-108.3, and 95.7-107.7, respectively. The relative standard deviations varied between 1.5% and 7.3% (n=5). The results showed that the proposed method was a rapid, convenient and feasible method for the determination of SAs in liquid samples.     

Determination of gold in ore by flame atomic absorption spectrometry with flow-injection on-line sorbent extraction preconcentration

Gold in ores was determined by flame atomic absorption spectrometry following on-line preconcentration by sorbent extraction in a flow-injection system. The medium polarity adsorption resin Amberlite XAD-8 packed in a 220-μl micro-column was used to collect gold(III) from hydrochloric acid sample solutions for 40 s at 7.6 ml/min. Ethanol was used to elute the adsorbed analytes into the nebulizer. Optimization studies were made on sample loading rate, elution rate and sample acidity. Some possible interferences on the determination are discussed. A 35-fold enrichment was achieved at a sampling frequency of 60 h^?1 and with an RSD of 1.4%. The detection limit (3σ) and 2 μg l^?1. Results for gold in ore samples showed good agreement with those obtained using activated carbon adsorption preconcentration. The recoveries were 97–108%.     

Determination of europium(III) in environmental samples using a flow injection analysis system with on-line preconcentration and spectrophotometric detection

A simple and accurate flow injection analysis system coupled with spectrophotometric detector was developed for preconcentration and determination of europium(III) in aqueous samples. The developed flow system includes a europium preconcentration step in a column packed with Amberlite XAD-4 resin impregnated with nalidixic acid at pH 7.0. The europium complex was desorbed from the resin by 0.1 mol L^?1 HCl and mixed with arsenazo-III solution (0.05 % solution in 0.1 mol L^?1 HCl) and taken to the flow through cell of spectrophotometer where its absorbance was measured at 661 nm. The optimum preconcentration system, chemical and FIA variables were investigated. The preconcentration factors obtained were 115 and 500, detection limits of 0.43 and 0.1 μg L^?1, sample throughputs of 40 and 10 were obtained for preconcentration time of 60 and 300 s respectively. The proposed system showed good precision and accuracy with relative standard deviation of 1.5 %. The method has been applied to the determination of europium(III) in real water samples and certified reference material IAEA-SL-1 (Lake sediment).     

Development of an Efficient Procedure for Determination of Copper,Zinc and Iron after Solid Phase Extraction on 3‐(1‐(1‐H‐Indol‐3‐yl)‐3‐Phenylallyl)‐1H‐Indole Loaded on Duolite XAD 761

A method for the simultaneous preconcentration of Cu²⁺,Zn²⁺ and Fe³⁺ ions, in some food samples has been reported. The method is based on the adsorption of 3‐(1‐(1‐H‐indol‐3‐yl)‐3‐phenylallyl)‐1H‐indole (IPAI) loaded on Duolite XAD 761. The metal ions adsorbed on the modified solid phase resin are eluted using 6 mL of 4 mol L^?1 nitric acid. The influences of the analytical parameters including pH and amount of ligand and solid phase and type and amount of surfactant and sample volume on the metal ions recoveries were investigated. The effects of matrix ions on the retentions of the analytes were also examined. The recoveries of analytes were generally higher than 95% with a RSD lower than 5%. The method has been successfully applied for these metals content evaluation in some real samples.     

Determination of seven polyphenols in water by high performance liquid chromatography combined with preconcentration

A method for determination of seven polyphenols (chlorogenic acid, esculetin, caffeic acid, scopoletin, rutin, quercetin hydrate, kaempferol) by reversed-phase high performance liquid chromatography (RP-HPLC) combined with preconcentration was developed. The preconcentration was accomplished by adsorption-desorption method with a styrene-divinylbenzene resin (XAD-4), and the analytes were desorbed by methanol. The parameters of adsorption and desorption, such as the amounts of resin, adsorption time, pH of the adsorption solution, and the volume of methanol for desorption were optimized. RP-HPLC with photodiode array detector (PAD) was employed for the qualitative and quantitative analysis. Methanol and acetic-water (1:99, v/v) solution were used as the mobile phase, and a gradient program was established for separation. Calibration curves of the seven analytes were obtained in the range of 0.8-3 mg L⁻¹, with correlation coefficients (R) higher than 0.9990. With standard samples, the recoveries for the preconcentration step under optimal conditions were 93-99%, and the relative standard deviations were 0.2-2.0% (n = 5). Polyphenols in simulated tobacco-polluted water were analyzed with the optimized conditions. Chlorogenic acid and rutin were found and determined, whose concentrations were 32.8 and 19.2 μg L⁻¹, respectively. The spiked recoveries of the polyphenols were 83-95% except quercetin hydrate (63%), the relative standard deviations were less than 3.5% (n = 5).     

Spectrophotometric determination of trace amounts of tungsten in geological samples after preconcentration on Amberlite XAD-1180

A method for the preconcentration of trace amounts of tungsten as its thiocyanate complex, using a column filled with Amberlite XAD-1180 resin, is proposed. After elution with a small volume of acetone, the analyte was determined spectrophotometrically with potassium thiocyanate and stannous chloride. The influence of several ions, as interferents, is discussed. The proposed method was applied to the determination of tungsten in geological samples with good analytical results, such as recoveries of 95% or above, relative standard deviations of 6% or below (n = 10) and a detection limit of 12 mugl(-1).     

Studies on synthesis and application of XAD-4-salen chelate resin for separation and determination of trace elements by solid phase extraction

The use of chemically modified XAD-4-salen chelating resin had been studied for the separative concentration of metal ions from an aqueous solution. XAD-4-salen was synthesized by diazonium coupling reaction of salen[N,N′-bis(salicylidene)ethylenediamine] and Amberlite XAD-4 resin. The distribution coefficient at various pH values and adsorption capacities were obtained with respect to Cu(II), Pb(II) and Bi(III). Trace elements were pre-concentrated on the synthesized XAD-4-salen by batch method for atomic absorption spectrometric determination. Some conditions, such as the pH of aqueous solution, amount of XAD-4-salen, kinds and concentration of acids were optimized for the analytical application of XAD-4-salen. For the pre-concentration of metal ions, the pH of the aqueous solution was adjusted to approximately 5.5, and then it was stirred 30 min after the addition of 50 mg of pulverized XAD-4-salen. The adsorbed metal ions were desorbed by 10 mL of 1.0 M HNO₃. The desorption efficiency of Bi(III) was enhanced by the addition of 30 mg/L of Pd(II). The addition of Pd(II) as a matrix modifier could improve the reproducibility and sensitivity in the Atomic Absorption Spectroscopy (AAS) determination of volatile lead and bismuth. In the present study, this procedure has been applied for the determination of Cu(II), Pb(II) and Bi(III) in real samples of five kinds of river water, using a standard calibration curve method. Recoveries of 85–120% were obtained in the spiked samples in which given amount of analytes were added.