Magnetic and magnetostrictive behavior of Dy3+ doped CoFe2O4 single crystals grown by flux method

We studied the effect of Dy³⁺ content on the magnetic properties of cobalt ferrite single crystal. The single crystals of CoFe_1.9Dy_0.1O₄ were grown by the flux method using Na₂B₄O₇.10 H₂O (Borax) as a solvent (flux). The black and shiny single crystals were obtained as a product. The X-ray diffraction analysis at room temperature confirmed the spinel cubic structure with lattice constant a=8.42 Å of the single crystals. The compositional analysis endorses the presence of constituents Co, Fe and Dy elements after sintering at 1300 °C within the final structure. The magnetic hysteresis measurements at various temperatures viz. 10 K, 100 K, 200 K and 300 K reveal the soft ferrimagnetic nature of the single crystal than that of for pure CoFe₂O₄. The observed saturation magnetization (M_s) and coercivity (H_c) are found to be lower than that of pure CoFe₂O₄ single crystal. The magnetostriction (λ) measurement was carried out along the [001] direction. The magnetic measurements lead to conclude that the present single crystals can be used for magneto-optic recording media.     

Nitridation of SiO2–B2O3 aerogels

SiO₂–B₂O₃ aerogels have been prepared by drying wet gels at a supercritical condition for ethanol in an autoclave. Aerogels have been nitrided for 6 h in flowing ammonia at the temperature of 1200 °C. It has been found that the amount of nitrogen incorporated in these aerogels always exceeds 20 wt%. This is a much higher value compared with the amount of nitrogen incorporated in a pure silica aerogel nitrided at the same conditions. The specific surface area of SiO₂–B₂O₃ aerogels has been between 312 and 359 m²/g. After nitridation some shrinkage of aerogels has been observed and the surface area decreases about 20%. In FTIR spectra of SiO₂–B₂O₃ aerogels a typical bands for SiO₂ are observed. After nitridation a shift and broadening of 1100 cm^?1 band to lower wavenumbers indicates that Si–N and B–N bonds are formed in nitrided aerogels.     

Ultrafine Co1−xZnxFe2O4 particles synthesized by hydrolysis: Effect of thermal treatment and its relationship with magnetic properties

Co_1−xZn_xFe₂O₄ (x = 0, 0.2 and 0.4) fine powders with particles size of 3 nm were prepared by hydrolysis method. The powders were annealed at 500 °C for 3 h. With heat treatment, the average particles size increased to 12 nm with corresponding increase in blocking temperature, saturation magnetization and reduced remanence. A significant increase in coercive field was found only for the pure CoFe₂O₄.     

The effect of calcination temperature on the crystallinity of TiO2 nanopowders

TiO₂ nanopowders have been prepared using 0.1 M titanium tetraisopropoxide (TTIP) in varied pH aqueous solution containing TMC and NP-204 surfactants. Only the powder acquired from a solution of pH=2 has a regular particle size distribution. Anatase phase powders are obtained by calcination in nitrogen in the 250–500°C temperature range. When calcined at 400°C, the diameter of the nanoparticles is approximately 10 nm with a specific surface area of 106.9 m²/g. As the calcination temperature is increased, the particle size increases. Rutile phase powders are formed at calcination temperatures above 600°C.     

Improvement in optical transmission of the ambient pressure dried hydrophobic nanostructured silica aerogels with mixed silylating agents

The experimental results on the preparation of transparent and hydrophobic silica aerogels based on ion exchanged sodium silicate (Na₂SiO₃) using mixed silylating agents of trimethylchlorosilane (TMCS), hexamethyldisiloxane (HMDSO) and hexamethyldisilazane (HMDZ) are reported. Hydrogels were prepared with ion exchanged Na₂Si0₃ of 1.10 specific gravity with 1 N ammonium hydroxide (NH₄OH). The resulted gels were exchanged with methanol solvent followed by silylation using HMDZ + HMDSO or TMCS + HMDZ or TMCS + HMDSO mixture in methanol and hexane and dried the gels at room temperature for 24 h, at 50 and 200 °C for 1 h each. It has been observed that the percentage of the silylating agent in the mixture, time interval of addition of one agent followed by another and volume of silylating mixture have an effect on density, % of optical transmission, % of porosity, porevolume, thermalconductivity and refractive index of the aerogels. Hydrophobicity of the aerogels was studied by contact angle measurements. The TMCS + HMDSO aerogels have been found more hydrophobic (contact angle > 150°) than the other aerogels. Further, aerogels have been characterized by pore size distribution, Fourier Transform Infra Red Spectroscopy (FTIR), Transmission Electron Microscopy (TEM) and thermogravimetric analysis and differential thermal analysis (TGA–DTA) techniques. It has been found that the weight increase is the highest (325%) for HMDSO + HMDZ aerogels and lowest (1.2%) for HMDSO + TMCS aerogels by keeping the aerogels in the atmosphere over a period of 18 months. Low density (0.042 g/cc) transparent (85%), low thermal conductive (0.047 W/m K), low refractive index (1.0088) and hydrophobic (152°) silica aerogels were obtained with equivolume TMCS + HMDSO mixture of 10 ml, time interval of addition of 12 h between the two reagents prior addition of TMCS followed by HMDSO for 24 h of silylation period. It was found from the TGA–DTA of the aerogels that hydrophobicity of the aerogels remained up to the temperature of 425 °C.     

Investigation of the effective parameters on the synthesis of Ni-ferrite nanocrystalline powders by coprecipitation method

In this work, synthesis of nanostructured NiFe₂O₄ powders by coprecipitation method using novel precursors, followed by calcination was investigated for the first time. The synthesis was started by dissolving Fe and Ni chlorides and ammonium ferrous sulfate in deionized water. After stirring, the precipitating agent of NaOH was added to the solution and after 1 h aging, the resultant precipitates were washed with deionized water and acetone. Then the powder was characterized and the effects of different parameters such as molarity of precipitant, calcination temperature and the molar ratio of Ni²⁺ ion to the total iron ions were studied. It is concluded that an increase in molarity of precipitant can decrease the calcination temperature. The best conditions giving a single phase Ni-ferrite were using of 2.2 molar NaOH, calcination temperature of 900 °C and the molar ratio of nickel to iron as 0.5. The crystallite size of resulting ferrites was below 50 nm.     

Thermal expansion of glass–ceramics in the system BaO/Al2O3/B2O3

Glasses in the system BaO/Al₂O₃/B₂O₃ with and without the addition of platinum were melted. In one sample series, the BaO-concentration was varied while the ratio [Al₂O₃]/[B₂O₃] was kept constant. In another sample series, the [BaO]/[Al₂O₃]-ratio (= 0.9) was kept constant and the B₂O₃ concentration was varied. The samples were thermally treated at 720 °C for 24 h and subsequently at 780 °C for 4 h. In most thermally treated samples, the crystalline phase BaO · Al₂O₃ · B₂O₃ occurred. At some compositions, the platinum-doped samples showed larger concentrations of the crystalline phases. The most remarkable property of the obtained glass–ceramics is their zero or negative thermal expansion coefficient. Here, notable differences were observed: samples with fine grained microstructures showed thermal expansion coefficients approximately zero up to temperatures of around 80 °C. By contrast, samples with coarser microstructures and large spheroidal crystals exhibit negative expansion coefficients up to temperatures of around 280–375 °C. The thermal expansions of these samples were close to those of the mean thermal expansion of the unit cell of the BaO · Al₂O₃ · B₂O₃ phase. The thermal expansion of the fine grained samples was approximately equal to that of the crystallographic a-axis of the BaO · Al₂O₃ · B₂O₃ phase.     

Structural investigations of nitrided Nb2O5 and Nb2O5–SiO2 sol–gel derived films

Sol–gel derived xNb₂O₅–(100 ? x)SiO₂ films (where x = 100, 80, 60, 50, 40, 20, 0 mol%) were nitrided at various temperatures (800 °C, 900 °C, 1000 °C, 1100 °C and 1200 °C). The structural transformations occurring in the films as a result of ammonolysis were studied using X-ray diffraction (XRD), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The XRD results have shown that the temperatures below 1100 °C were too low to obtain a pure NbN phase in the samples. The AFM observations indicate that the formation of the NbN phase and the size of NbN grains are related to the silica content in the layer. NbN grains become more regular and larger as the niobium content increases. The maximum grain size of about 100 nm was observed for x = 100. Preparation of the Nb₂O₅–SiO₂ sol–gel derived layers and the subsequent nitridation is a promising method of inducing crystalline NbN in amorphous matrices. It follows from the XPS results that a small amount of Nb₂O₅ remains in the films after nitridation at 1200 °C and that nitrogen reacted not only with Nb₂O₅ but also with SiO₂.     

Comparative study on photoluminescence of amorphous and nano-crystalline YAG:Tb phosphors prepared by a combustion method

Amorphous and nano-crystalline Y₃Al₅O₁₂:Tb phosphor samples were obtained via a facile combustion method by calcination at various temperatures, using yttrium oxide and aluminum nitrite as starting materials and citric acid as fuel. XRD, FT-IR and TEM results showed that the products were amorphous if prepared at 750 °C, well-crystalline when treated above 850 °C. In addition, partially crystalline YAG phase was observed at 800 °C (in air). The excitation spectra of the samples calcined at 750 °C and 800 °C exhibited some difference in the 230–255 nm range in comparison to those of nano-crystalline YAG:Tb, i.e. an extra band centered at 250 nm was detected via Gaussian curve-fitting. Furthermore, the photoluminescence intensity of as-synthesized samples decreased obviously with increasing the crystallinity under 250 nm excitation. Contrary, it increased monotonously when altering the excitation wavelength to 323 nm. The concentration-dependent emission spectra of samples calcined at 800 °C revealed that the strongest intensity could be obtained with 10% Tb doping. Red-shifts indicated changes of the inter-atomic distances within the Tb³⁺ coordination polyhedron with increasing Tb concentration. The low temperature photoluminescence of partially crystalline YAG:10% Tb was also investigated, displaying good-resolution but reduced intensity compared to the room-temperature photoluminescence.     

Performance investigation of Li2O–Al2O3–4SiO2 based glass–ceramics with B2O3, Na3AlF6 and Na2O fluxes

Influence of single fluxes (10 wt.% B₂O₃), bi-component fluxes (4 wt.% B₂O₃ + 6 wt.% Na₃AlF₆), and complex fluxes (4 wt.% B₂O₃ + 4 wt.% Na₃AlF₆ + 2 wt.% Na₂O) on the thermal kinetic parameters, microstructure, flexural strength and coefficient of thermal expansion (CTE) of Li₂O–Al₂O₃–4SiO₂ (LAS) glass–ceramics was investigated through differential thermal analysis (DTA), X-ray diffraction (XRD), and scanning electron microscope (SEM). The results showed that complex fluxes could efficiently decrease transition temperature (T_g) and crystallization temperature (T_p), and accelerate the formation of needle-like β-spodumene crystals which benefit high flexural strength. The homogeneous LAS glass–ceramic (sample C₃) which has a high strength of 132.4 MPa and low CTE (100–650 °C) of 2.74 × 10^? 6/°C is obtained by doping of the initial LAS glass by complex fluxes of 4 wt.% B₂O₃, 4 wt.% Na₃AlF₆, and 2 wt.% Na₂O, nucleating at 630 °C/120 min and then crystallized at 780 °C/120 min. It is worthy of further investigation as a bonder of diamond composite material due to its outstanding prosperities.     

Phase evolution on heat treatment of sodium silicate water glass

Heat treatment of sodium silicate water glass of the nominal composition Na₂O/SiO₂ = 1:3 was carried out from 100 °C up to 800 °C and the advancement of the resulting phases was followed up by powder X-ray diffraction, scanning electron microscopy and thermogravimetry along with differential thermal analysis. The water glass, initially being an amorphous solid, starts to form crystals of β-Na₂Si₂O₅ at about 400 °C and crystallizes the SiO₂ modification cristobalite at about 600 °C that coexists along with β-Na₂Si₂O₅ up to 700 °C. At 750 °C Na₆Si₈O₁₉ appears as a separate phase and beyond 800 °C, the system turns into a liquid.     

Synthesis of magnesium borates using sodium borate and magnesium sulfate

Synthesis conditions of magnesium borate compounds in aqueous medium using Na₂B₄O₇ · 10H₂O and MgSO₄ · 7H₂O were determined. The effects of B/Mg mole ratio, pH, reaction time and precipitation temperature on the reaction performed at 90 °C were examined. 0.04Na₂O · MgO · 1.23B₂O₃ · 3.42H₂O and 0.06Na₂O · MgO · 1.65B₂O₃ · 3.34H₂O were synthesized at optimum B/Mg mole ratios of 3.60 and 4.80 by precipitation at 5 °C and the amorphous compounds formed were identified by B, Mg, Na and XRD analyses and some physical tests.     

Synthesis and characterization of CoFe2O4–PVP nanocomposites

Cobalt ferrite–poly(N-vinyl-2-pyrrolidone) nanocomposites were prepared by drying a dispersion of cobalt ferrite (CoFe₂O₄) nanoparticles and poly(N-vinyl-2-pyrrolidone). Magnetic measurements indicate a superparamagnetic behavior. Zero-field-cooling magnetization experiments at 100 Oe show different trends depending on the CoFe₂O₄ nanoparticles size. For the smaller ones (3.9 nm), the blocking temperatures shift to lower temperatures with increasing concentration; however, this shift is not observed for the larger ones (6.6 nm). These differences can be related to the anisotropy constant of the CoFe₂O₄ nanoparticles and the interparticle dipolar interactions.     

Crystal growth of ZrW2O8 and its optical and mechanical characterization

ZrW₂O₈ is known for its isotropic negative thermal expansion over a wide of range of temperature from ?272 to 777 °C. However, ZrW₂O₈ melts incongruently at 1257 °C and is stable only over a short temperature interval between 1105 and 1257 °C. This makes the growth of single crystals a formidable challenge. In order to study the intrinsic properties of this compound, a repeatable, viable single crystal growth strategy is required. Here we report a simple, self-seeding, self-fluxing single crystal growth process which resulted in single crystals of ZrW₂O₈ up to about 4 mm in size. Grown crystals were characterized by X-ray diffraction (XRD), Raman spectroscopy and Fourier transform infrared (FTIR) spectroscopy. Mechanical properties of the crystals were studied using nanoindentation.     

Incorporation of B2O3 in CaO-SiO2-P2O5 bioactive glass system for improving strength of low-temperature co-fired porous glass ceramics

Bioactive glass ceramics (BGCs) have different rates of biodegradation and mechanical properties depending on their chemical compositions and sintering temperatures. The present study was aimed to develop the boron-rich, phosphorus-low CaO–SiO₂–P₂O₅–B₂O₃ bioactive glasses (BG-B_x, X = 0, 10, 20) potentially for improving the mechanical properties of BGCs via low-temperature co-fired process. The B₂O₃-free BG-B₀ shrunk well at ~ 726 °C and melted at over 1050 °C, while the onset shrinking and melting temperatures of the 20 mol% B₂O₃-doped BG-B₂₀ was lowered to ~ 648 °C and ~ 952 °C, respectively. The BG-B₂₀ thermally treated at 850–950 °C was transformed into wollastonite and calcium borate, and crystallization decreased the kinetics but did not inhibit the development of hydroxyapatite on their powder and disc surface when immersed in simulated body fluid. The in vitro degradation in Tris buffer confirmed that the degradation rate markedly increased with increasing boron content in BG-B_x. The compressive strength and flexural strength of the 10% BG-B₂₀-reinforced 45S5 porous BGC sintered at 850 °C was nearly four times than that of 45S5 porous constructs. These studies suggest that the boron-rich, phosphorus-low CaO–SiO₂–P₂O₅–B₂O₃ system is a promising biomaterial and potential low temperature co-fired aid for improving the mechanical and biological properties of porous BGCs.     

Fabrication of Cr4+,Nd3+:YAG transparent ceramics for self-Q-switched laser

Transparent 0.1 at.%Cr,1.0 at.%Nd:YAG (Y₃Al₅O₁₂) ceramics were fabricated by a solid-state reaction and vacuum sintering with CaO as a charge compensator and tetraethyl orthosilicate (TEOS) as a sintering aid using high-purity powders of Al₂O₃, Y₂O₃, Nd₂O₃ and Cr₂O₃. The mixed powder compacts were sintered at 1800 °C for 5 h and 30 h under vacuum. The optical transmittance of the Cr,Nd:YAG ceramics sintered at 1800 °C for 5 h and 30 h is ∼63% and ∼78% in the infrared wavelengths, respectively. The two samples exhibit pore-free structures and the average grain size is about 10 and 20 μm. For the sample sintered at 1800 °C for 5 h, the dominant fracture mechanism is the transgranular fracture. With increase of holding time up to 30 h, the ratio of intergranular fracture surfaces increase and more Cr³⁺ ions in the Cr,Nd:YAG ceramic transform to Cr⁴⁺. High-quality Cr⁴⁺,Nd³⁺:YAG transparent ceramics may be a potential self-Q-switched laser material.     

Ultra-high thermal expansion glass–ceramics in the system MgO/Al2O3/TiO2/ZrO2/SiO2 by volume crystallization of cristobalite

Glasses in the system MgO/Al₂O₃/TiO₂/ZrO₂/SiO₂ with and without the addition of As₂O₃ and Sb₂O₃ were thermally treated. Up to a temperature of 950 °C, this resulted in the formation of ZrTiO₄, sapphirine and high quartz solid solution. Annealing at higher temperatures led to the formation of low quartz solid solutions, ZrTiO₄ and sapphirine. This resulted in a continuous increase of density, hardness, fracture toughness and thermal expansivity. In the glass doped with As₂O₅ and Sb₂O₅ annealing temperatures >1000 °C resulted in the formation of cristobalite instead of quartz. Then the density, hardness and strength decreased again, while the fracture toughness (up to 2.8 MPa m^1/2) and the thermal expansion coefficient increased strongly. In the dilatometric curves, a steep increase in expansion is observed in the temperature range from 100 to 200 °C, which is attributed to the transformation of low cristobalite to high cristobalite. The mean linear thermal expansion coefficient (25–200 °C) is 20 × 10^?6 K^?1 and the largest up to now reported in the literature for alkali-free silicate glass–ceramics.     

Mechanism of crystallization of fast fired mullite-based glass–ceramic glazes for floor-tiles

The mechanism of crystallization from a B₂O₃-containing glass, with composition based in the CaO–MgO–Al₂O₃–SiO₂ system, to a glass–ceramic glaze was studied by different techniques. Glass powder pellets were fast heated, simulating current industrial tile processing methods, at several temperatures from 700 to 1200 °C with a 5 min hold. Microstructural study by field emission scanning electron microscopy revealed that a phase separation phenomenon occurred in the glass, which promoted the onset of mullite crystallization at 900 °C. The amount of mullite in the glass heated between 1100 and 1200 °C was around 20 wt%, as determined by Rietveld refinement. The microstructure of the glass–ceramic glaze heated at 1160 °C consisted of interlocked, well-shaped, acicular mullite crystals longer than 4 μm, immersed in a residual glassy phase.     

An alumina mat with a nano microstructure prepared by centrifugal spinning method

Ceramic fiber products specially alumina mat because of low thermal conductivity and high melting point are used as high temperature insulating materials. Alumina has so high melting point (T_m > 2040 °C) that its mat can be produced through sol–gel method. In this research alumina mat has been manufactured by sol–gel spinning method using our laboratory-designed centrifugal spinneret. The desired viscosity of sol for spinning is 150 P. Phase transformation of the product begins at 600 °C and there is not any amorphous phase at 800 °C and theta alumina (θ-Al₂O₃) is the main phase. In this work, transformation of transitional phase to alpha alumina (α-Al₂O₃) takes place from 1000 °C to 1200 °C. The optimum percent of silica in alumina mat is 4 wt%. Fibers constitute network structure that their average diameter is about 10 μm and contains very fine grains (100 nm). The silica percent concerning the limits of this study (<10 wt%) does not effect on fiber diameter, but grain size decreases from about 200 nm to less than 100 nm while increasing silica percent.     

Precipitation of zinc ferrite nanoparticles in the Fe2O3–ZnO–SiO2 glass system

Glass materials in the ZnO–Fe₂O₃–SiO₂ system, containing zinc ferrite nanoparticles, were prepared by the sol–gel method and characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), Mössbauer spectroscopy, AC- and DC-magnetization techniques. The gel samples, dried at 130 °C, were further heat treated in air at 500 and 800 °C. At 500 °C zinc ferrite and hematite nanoparticles, with an average size of approximately 24 nm, were precipitated in the brown and opaque 10ZnO–10Fe₂O₃–80SiO₂ and in the ruby colored transparent 5ZnO–5Fe₂O₃–90SiO₂ and 2.5ZnO–2.5Fe₂O₃–95SiO₂ glass matrices. In the 5ZnO–5Fe₂O₃–90SiO₂ sample the nanoparticles exhibited ferro or ferrimagnetic interactions combined with superparamagnetism with a blocking temperature of approximately 14 K. Heating at 800 °C seems to cause partial dissolution of the zinc ferrite and hematite particles in all the investigated compositions. Accordingly at 800 °C the 5ZnO–5Fe₂O₃–90SiO₂ glass shows a paramagnetic behavior down to 2 K.