Structure and properties of Ni60(Nb100−xTax)34Sn6 bulk metallic glass alloys

Refractory bulk metallic glasses and bulk metallic glass composites are formed in quaternary Ni-Nb-Ta-Sn alloy system. Alloys of composition Ni₆₀(Nb_100−xTa_x)₃₄Sn₆ (x = 20, 40, 60, 80) alloys were prepared by injection-casting the molten alloys into copper molds. Glassy alloys are formed in the thickness of half mm strips. With thicker strips (e.g., 1 mm), Nb₂O₅ and Ni₃Sn phases and the amorphous phase form an in situ composite. Glass transition temperatures, crystallization temperatures, and ΔT_x, defined as T_x1 − T_g (T_x1: first crystallization temperature, T_g: glass transition temperature) of the alloys increase dramatically with increasing Ta contents. These refractory bulk amorphous alloys exhibit high Young’s modulus (155-170 GPa), shear modulus (56-63 GPa), and estimated yield strength (3-3.6 GPa).     

Glass-forming ability and crystallization of bulk metallic glass (HfxZr1−x)52.5Cu17.9Ni14.6Al10Ti5

We have produced a series of bulk metallic glasses of composition (Hf_xZr_1−x)_52.5Cu_17.9Ni_14.6Al₁₀Ti₅ (with x=0-1) by an arc melting/suction casting method. The density of these alloys increases by nearly 67% with increasing Hf content from 6.65 g/cm³ (x=0) to 11.09 g/cm³ (x=1). Over the same composition range the glass-forming ability decreases, as demonstrated by the size of the largest amorphous ingots that can be cast without crystallization. Although both the glass transition temperature and the melting temperature increase linearly with increasing Hf content, the reduced glass transition temperature (T_g/T_m) decreases, from 0.64 (x=0) to 0.62 (x=1), which suggests that the `confusion principle' correlating increased glass-forming ability with increased number of components, does not apply in this case due to the chemical similarity between Zr and Hf. A different crystallization behavior is observed for Zr-based and Hf-based glasses. The final crystalline phases are CuZr₂ and Zr₂Ni for Zr-based alloys, and Al₁₆Hf₆Ni₇ and CuHf₂ for Hf-based alloys.     

Crystallization processes in amorphous Zr54Cu46 alloy

The crystallization of amorphous Zr₅₄Cu₄₆ alloy was investigated by using X-ray diffraction (XRD), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM) techniques. The experimental results show that an endothermic peak in DSC traces for amorphous Zr₅₄Cu₄₆ alloy exists at about 1006 K, indicating following eutectoid reaction occurs, namely, Cu₁₀Zr₇+CuZr₂↔CuZr in amorphous Zr₅₄Cu₄₆ alloy during heating. With increasing the heating rate, the glass transition temperature T_g and onset crystallization temperature T_x of amorphous Zr₅₄Cu₄₆ alloy increase in parallel, and the supercooled liquid region ΔT_x (=T_x−T_g) holds almost constant with an average value of 44 K. Both XRD and TEM results prove that Cu₁₀Zr₇ and CuZr₂ are main crystallization products for amorphous Zr₅₄Cu₄₆ alloy under continuous heating conditions. No CuZr phase is identified because of its small precipitation amount. Finally, the crystallization processes of amorphous Zr₅₄Cu₄₆ alloy were summarized.     

Non-isothermal crystallization kinetics study on new amorphous Ga20Sb5S75 and Ga20Sb40S40 chalcogenide glasses

Bulk glasses of the system Ga₂₀Sb_xS_80−x (x = 5 and 40) were prepared for the first time by the known melt quenching technique. Non-isothermal differential scanning calorimetric (DSC) measurements of as-quenched Ga₂₀Sb_xS_80−x (x = 5 and 40) chalcogenide glasses reveal that the characteristic temperatures e.g. the glass transition temperature (T_g), the temperature corresponding to the maximum crystallization rate (T_p) recorded in the temperature range 400-650 K for x = 5 and 480-660 K for x = 40 are strongly dependent on heating rate and Sb content. Upon heating, these glasses show a single glass transition temperature (T_g) and double crystallization temperatures (T_p1 and T_p2) for x = 5 which overlapped and appear as a single crystallization peak (T_p) for x = 40. The activation energies of crystallization E_c were evaluated by three different methods. The crystallization data were examined in terms of recent analysis developed for non-isothermal conditions. The crystalline phases resulting from (DSC) have been identified using X-ray diffraction.     

Potentiodynamic polarization studies on amorphous Zr46.75Ti8.25Cu7.5Ni10Be27.5, Zr65Cu17.5Ni10Al7.5, Zr67Ni33 and Ti60Ni40 in aqueous HNO3 solutions

Potentiodynamic polarization studies were carried out on virgin specimens of Zr-based bulk amorphous alloys Zr_46.75Ti_8.25Cu_7.5Ni₁₀Be_27.5 and Zr₆₅Cu_17.5Ni₁₀Al_7.5, and conventional-type binary amorphous alloys Zr₆₇Ni₃₃ and Ti₆₀Ni₄₀ in solutions of 0.2 M, 0.5 M and 1.0 M HNO₃ at room temperature. The values of the corrosion current density (I_corr) for the bulk amorphous alloy Zr_46.75Ti_8.25Cu_7.5Ni₁₀Be_27.5 were found to be comparable with those of Zr₆₅Cu_17.5Ni₁₀Al_7.5 in 0.2 M and 0.5 M HNO₃, but the value of I_corr for the former was almost three times more than that of the latter in 1.0 M HNO₃. In the case of conventional binary amorphous alloys, Ti₆₀Ni₄₀ showed lower value of I_corr as compared to Zr₆₇Ni₃₃ in 0.5 M and 1.0 M HNO₃ and a comparable value of I_corr in 0.2 M HNO₃. In general, the binary Ti₆₀Ni₄₀ displayed the best corrosion resistance among all the alloys in all the cases and the corrosion current density (I_corr) for all the alloys was found to increase with the increasing concentration of nitric acid. It is noticed that the bulk amorphous alloys do not possess superior corrosion resistance as compared to conventional binary amorphous alloys in aqueous HNO₃ solutions. The observed differences in their corrosion behavior are attributed to different alloy constituents and composition of the alloys investigated.     

Crystallization behaviour of an amorphous Ti50Be40Zr10 alloy

The crystallization behaviour of an amorphous Ti₅₀Be₄₀Zr₁₀ alloy during a continuous heating mode from room temperature to 973 K and isothermal annealing at temperatures above the glass transition temperature is examined by differential scanning calorimetry (DSC), small-angle X-ray scattering (SAXS) measurement and large-angle X-ray diffractometry (LAXD). DSC indicated two well-defined exothermic peaks, a slight shoulder at the higher temperature side of the second peak and a small heat evolution at higher temperature. The Kissinger plot for the first and the second peak gives a straight line, from which the apparent activation energy is estimated to be 269 and 413 kJ/mol respectively; the enthalpies for the first and second crystallization process are 1.04 kJ/mol and 4.39 kJ/mol for a heating rate of 20 K/min. The SAXS intensities increase sharply after annealing at about 673 K (corresponding to the first peak in the DSC curves); the scattering is due to the formation of fine-scale crystalline Ti particles by the LAXD. The size of the particles does not change significantly while the number of scattering particles increases, indicating that the reaction is almost nucleation controlled and the growth is very limited. Another crystalline phase would appear in addition to the Ti particles on annealing at temperatures above about 753 K (corresponding to the second peak in the DSC curves), where the SAXS intensities decrease compared with those for only the first-stage of crystallization. The crystalline phase might be a metastable cubic phase with the lattice parameter a₀?0.2994 nm.The sequence in the crystallization of the initial non-crystalline material is amorphous → microcrystalline (MS I) → crystalline (MS II; S III), although the structure of crystalline phase in the final stage (S III) was not identified. It is also likely that cold-rolling does not have a perceptible effect on the crystallization behaviour of the present amorphous alloy.     

Length and density changes of amorphous Pd40Cu30Ni10P20 alloys due to structural relaxation

The density changes of bulk amorphous Pd₄₀Cu₃₀Ni₁₀P₂₀ due to structural relaxation under isothermal heat treatment were measured using the buoyancy method. The corresponding length changes of amorphous Pd₄₀Cu₃₀Ni₁₀P₂₀ ribbons applying non-isothermal heat treatment are determined applying dilatometry. The measured density changes Δρ(T=const.,t)/ρ_o as a function of isothermal heat treatment increase close to the glass transition up to 0.18%. The measured density changes as a function of temperature and time are furthermore reversible. The experimental data validate the model predictions of the free volume model for length and density changes of amorphous alloys due to structural relaxation applying isothermal and non-isothermal heat treatment.     

A thermodynamic and kinetic investigation of amorphous (1−x)As2Se3 · xSb2Se3 alloys

The heats of formation of amorphous (1?x)As₂Se₃ · xSb₂Se₃ (x = 0 to 0.4) referred to crystalline As₂Se₃ and Sb₂Se₃ were measured by liquid metal solution calorimetry. The values of heats of formation of amorphous (1?x)As₂Se₃ · xSb₂Se₃ decreased from 1.39 ± 0.03 kcal · (g-at)^?1 at x = 0 to 1.27 ± 0.04 kcal · (g-at)^?1 at x = 0.4.The glass transition temperature and the temperatures of the maximum rates of crystallization and fusion were measured by differential scanning calorimetry. The glass transition temperature increased and the temperatures of the maximum rates of crystallization and fusion decreased with increasing Sb₂Se₃ content.The relaxation process in amorphous (1?x)As₂Se₃ · xSb₂Se (x = 0.3) was investigated by measuring changes in microhardness, small-angle X-ray scattering and heat capacity with time of annealing at several temperatures ranging from room temperature to 413 K. With increasing annealing time the microhardness, the height and the temperature of the glass transition peak increased whereas the intensity of small-angle X-ray scattering decreased. These changes reflect relaxation towards a more stable structure of smaller molecular mobility. The changes in the enthalpy with annealing time and the activation energy spectra for relaxation were derived from the heat capacity data. The effects of temperature and time of annealing on the various properties are explained in terms of structural changes and relaxation kinetics.     

Influence of outphase Cu50Ti50 amorphous alloy addition on microstructural evolution of mechanically alloyed Zr66.7Ni33.3 amorphous alloy

The influence of outphase Cu₅₀Ti₅₀ amorphous alloy addition on microstructural evolution of Zr_66.7Ni_33.3 amorphous alloy has been investigated using a mechanical alloying method. It has been found that the milling induced microstructural evolution is related to the change of peak positions of the first maximum on X-ray diffraction patterns of the as-obtained amorphous alloys. With increasing milling time, the 3 wt.% Cu₅₀Ti₅₀ addition can give rise to the cyclic amorphization transformation of the as-milled alloy. The mechanical stability of the mixing amorphous phase can be greatly enhanced with increasing Cu₅₀Ti₅₀ addition up to 10 wt.%. Moreover, the addition of outphase Cu₅₀Ti₅₀ amorphous alloy not only increases the onset crystallization temperature of Zr_66.7Ni_33.3 amorphous alloy but also alters its crystallization mode. The effect of outphase amorphous addition on the mechanical stability of the Zr_66.7Ni_33.3 amorphous phase has been discussed based upon the bond order theory.     

Stability of Ni-based bulk metallic glasses

Several ternary (Ni_xNb_ySn_z) refractory alloy glasses (RAGs) were studied at elevated temperatures in order to assess the stability of the amorphous state, i.e. devitrification, and to identify subsequent phase transformations in these materials. differential scanning calorimetry (DSC) experiments indicated a complex phase transformation sequence with several distinct crystallization and melting events being recorded above the glass transition temperature, T_g. Below T_g the RAG samples were studied with an in situ environmental X-ray furnace facility, which allowed step-wise isothermal ramping experiments commencing at a temperature below the reduced temperature of T/T_g ≈ 0.80. Distinct crystalline phases were observed when T/T_g ≈ 0.84 for ternary RAG alloys, while similar experiments on Zr-based Vit 106 glass alloys did not reveal any apparent phase separation until T/T_g ≈ 0.96. The phase separation kinetics followed an Arrhenius type of relationship with Ni₃Sn, and Nb₂O₅ being the principle crystalline precipitates.     

Pressure and heating rate dependence of the crystallization temperature for amorphous (Fe65Ni35)75P16B6Al3 and Ti50Be40Zr10

The crystallization temperature, T_x, was determined at constant heating rate, $\text{R =}\text{T}\text{?}\text{? 7}\text{K min}{}^{\mathrm{?1}}$, by monitoring the electrical resistance. Such experiments were carried out under pressures up to 2.5 GPa, and the resulting dT_x/dP was 15.9 K GPa^?1 for (Fe₆₅Ni₃₅)₇₅P₁₆B₆Al₃ and 8.7 K GPa^?1, 8.1 K GPa^?1 for the two crystallization processes in Ti₅₀Be₄₀Zr₁₀. The activation energies of crystallization under atmospheric pressure were obtained from measurements of T_x at rates from 0.05 K min^?1 ?55 K min^?1, analysed by plotting ln(T_x²R^?1) versus T_x^?1.     

Crystallization temperature of amorphous Fe80B20 under pressure

The resistance of rapidly quenched Fe₈₀B₂₀ was recorded versus T at a rate of 7 K/min and various pressures up to 2.5 GPa. The onset of crystallization, T_x, was defined by extrapolation at the sharp change in resistance associated with crystal growth. The resulting slope of T_x is 15 K/GPa. Separate measurements at atmospheric pressure yielded T_x versus rate of temperature increase, R = dT/dt. crystallization times from the literature were recalculated to yield T_x, and the results are compared with our data. Nominally amorphous materials of the same composition show markedly different properties. It is also shown that the variation of T_x with R is mostly due to the change in viscosity.     

Glass formation ability and mechanical properties of Ti40Cu40Zr10Ni10 alloy

Melt-spun ribbon and bulk samples in cylindrical rod form with diameter ranging from 2 mm to 4 mm of Ti₄₀Cu₄₀Zr₁₀Ni₁₀ alloy were prepared by melt-spinning technique and copper mould casting method, respectively. The microstructure, thermal stability and mechanical properties of the bulk samples were investigated. A completely glassy single phase is formed in the 2 mm rod sample. Increasing the diameter of the rod samples resulted in the formation of CuTi crystalline phase in the 3 mm and 4 mm rod samples. The 2 mm single glassy rod sample exhibited a large supercooled liquid region ΔT_x = 58 K and γ = T_x/(T_g + T_l) is 0.390, which indicated that the alloy possessed a good glass-forming ability. The bulk samples also exhibited good mechanical properties. The 2 mm rod sample showed the highest yield strength of about 2086 MPa. The 3 mm rod sample not only showed high yield strength of about 2000 MPa, but also enhanced plastic strain of about 0.71%.     

Crystallization behaviour of Al-based metallic glasses below and above the glass-transition temperature

The present paper aims to report an effect of a supercooled liquid region on crystallization behaviour of the Al₈₅Y_8−xNd_xNi₅Co₂ metallic glasses produced by rapid solidification of the melt. The paper describes the crystallization process at different regimes of heat treatment. It is found that crystallization behaviour of the above-mentioned Al-based metallic glasses above the glass-transition temperature and below it follows different transformation mechanisms. Formation of the primary nanoscale α-Al particles was observed during continuous heating or after isothermal annealing above the glass-transition temperature. During isothermal annealing below the glass-transition temperature an unknown metastable phase is formed conjointly with α-Al. The metastable phase formed in the Nd-free alloy varies from that in the Nd-bearing alloys. Al₈₅Nd₈Ni₅Co₂ amorphous alloy exhibiting no glass transition crystallizes equally during isothermal calorimetry at different temperatures and during continuous heating.     

Structural relaxation of Ti40Zr25Ni8Cu9Be18 bulk metallic glass

Ti₄₀Zr₂₅Ni₈Cu₉Be₁₈ bulk metallic glass has a unique quenched-in nuclei/amorphous matrix structure. The crystallization of quenched-in nuclei, when the experimental isothermal annealing time is within its incubation time, may not disturb the enthalpy relaxation, which makes it have the accordingly common enthalpy relaxation behavior with amorphous materials. The alloy's annealing time dependence of recovery enthalpy follows a stretched exponential function with the mean relaxation time obeying an Arrhenius law. The equilibrium recovery enthalpy ΔH_T^eq, mean relaxation time τ and stretching exponent β are all dependent on the annealing temperature, and generally, a higher annealing temperature comes with a lower value of ΔH_T^eq, τ and a higher value of β. Two parameters, β_g and τ_g, representing the stretching exponent and the mean structural relaxation time at the calorimetric glass transition temperature, respectively, are correlated with glass forming ability and thermal stability, respectively. For Ti₄₀Zr₂₅Ni₈Cu₉Be₁₈ BMG, the high value of β_g, which is much higher than 0.84 and approaches unity, reveals its good glass forming ability, while, on the other hand, the low value of τ_g indicates a worse thermal stability compared with typical BMGs.     

Thermal embrittlement of Fe-based amorphous ribbons

Thermal embrittlement of amorphous Fe_78?xNi_xSi₁₀B₁₂ and Co₇₈Si₁₀B₁₂ alloys has been studied. The majority of Fe-based amorphous alloys became brittle after annealing to temperatures significantly lower than their crystallization temperatures, whereas the non-Fe-based amorphous alloys remained ductile after annealing up to their crystallization temperatures. The present results emphasize on the key difference between the embrittlement behavior of Fe-based and non-Fe-based amorphous alloys. We point out a possible correlation between different phenomena like Invar effect, compositional inhomogenity, and residual stress playing a critical role in the thermal embrittlement of Fe-based amorphous alloys.     

Crystallization of amorphous Cu60Zr40 prepared by magnetron sputter deposition

The crystallization of amorphous Cu₆₀Zr₄₀ prepared by magnetron sputter deposition was studied by differential scanning calorimetry, X-ray diffraction and transmission electron microscopy. Calorimetric results were similar to those reported in the literature for liquid-quenched Cu₆₀Zr₄₀, including the manifestation of a glass transition. Crystallization above and below the glass transition temperature, T_g, occurred by nucleation and growth of the equilibrium phase, Cu₁₀Zr₇. This phase was characterized by convergent beam electron diffraction. With isothermal annealing below T_g, the time scale for crystallization indicated that the vapor-quenched alloy was kinetically more stable than the liquid-quenched alloy. This was interpreted as a difference in the quenched-in structures, produced by the different synthesis methods. During longer anneals, TEM analysis indicated that the structure was being contaminated by oxygen.     

Effect of carbon on the microstructural evolution of Zr66.7−xNi33.3Cx (x = 0, 1, 3) alloys during mechanical alloying

In the present paper, the effect of carbon on the microstructural evolution of Zr_66.7−xNi_33.3C_x (x = 0, 1, 3) alloys during mechanical alloying has been investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that these three alloys undergo similar amorphization and crystallization processes, and the final milling product is a metastable fcc-Zr_66.7−xNi_33.3C_x phase. The carbon addition can shorten the milling time for the complete amorphization reaction and enhance the stability of the formed amorphous alloy, which can suppress the mechanically induced amorphous-crystalline phase transformation with further increasing milling time.     

Crystallization behaviours ofCo100−1(x+y)NbxBy amorphous alloys

The crystallization behaviours of Co_100?1(x+y)Nb_xB_y amorphous alloys were investigated by means of differential thermal analysis and a conventional X-ray diffractometer. The crystallization sequences are discussed in terms of the equilibrium phase diagram of the ternary alloy system.Assuming crystallization occurs as a result of nucleation and growth, the stabilizing effect of eutectic phase separation on the crystallization is shown by introducing the effective free energy of the critical nucleus.     

Structural investigation of amorphous and liquid Ge0.175Te0.825 by neutron scattering

The angular distribution of intensities of 1.003 Å neutrons scattered by an alloy of Ge_0.175Te_0.825 both in the amorphous and in the liquid state have been measured. The bulk amorphous sample, prepared by water quenching of the melt, has been examined at room temperature and just above the crystallization temperature T_x. The liquid sample has been examined at 400, 600 and 800°C. The analysis of the structure factors obtained from the corrected and scaled intensities indicates that the structural features of the amorphous sample are similar to those which would be expected if it were possible to cool the alloy to room temperature, while maintaining it in the liquid state. The analysis of the radical distribution functions, from Fourier inversion of the structure factors, indicates that a change of the coordination number n₁ from 2.43 to 3.25 occurs in passing from the amorphous to the liquid state at 400°C. This result has been interpreted in terms of coordination models. In the liquid state, it has been found that a model with fourfold coordinated Ge and threefold coordinated Te is consistent with n₁=3.25. The internal consistency of this model for the liquid state allows us to make a reasonable choice between the possibility of a 3 or 4 fold coordination for Ge in the glass. We conclude that a model based on four-fold coordinated Ge and twofold coordinated Te seems an appropriate representation for the coordination of the amorphous material.