Evaluation of denuder sampling for a mixture of three common gaseous diisocyanates

A denuder sampler has been evaluated for a mixture of three gaseous diisocyanates, i.e. toluene diisocyanate (TDI), hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI). Sampling was performed at a total concentration of diisocyanates close to the Swedish occupational exposure limit (OEL), which is 10 ppbv (69-92 microg m(-3)), for a 5-min period. The denuder tube was coated with a chemosorptive stationary phase consisting of SE-30 (polydimethylsiloxane) and the derivatising reagent dibutylamine (DBA). It was shown that the denuder has a collection efficiency for HDI and IPDI comparable to that of an impinger method, while sampling of TDI resulted in an 8% lower concentration. Both short-term (15 min) and long-term (8 h) sampling periods were shown to yield reproducible results. For 8-h measurements, a sampling flow rate of 5 mL min(-1) was shown to be suitable for the investigated concentration range, i.e. 10-100 ppbv (69-921 microg m(-3)). A flow rate of 25 mL min(-1) or higher resulted in breakthrough after 8 h due to chromatography of the compounds in the adsorbent. The limit of detection (LOD) for the air sampling method is nearly 500 times lower than the OEL. The denuder tubes can be prepared at least 10 days prior to sampling without degradation of performance. Furthermore, they can be stored up to 6 days in a freezer after sampling without significant loss of analytes.     

Exposure to 2,4- and 2,6-toluene diisocyanate (TDI) during production of flexible foam: determination of airborne TDI and urinary 2,4- and 2,6-toluenediamine (TDA)

Occupational exposure to 2,4- and 2,6-toluene diisocyanate (2,4- and 2,6-TDI) was measured during the production of flexible foam. The usefulness of urinalysis of the TDI-derived amines, 2,4- and 2,6-toluenediamine (2,4- and 2,6-TDA), for exposure assessment was compared with air monitoring. Urine samples were collected from 17 employees at two plants. The workers' personal exposure was measured using 1-(2-methoxyphenyl)-piperazine (2MP)-impregnated glass fibre filters for sampling and high-performance liquid chromatography (HPLC) with ultraviolet (UV) and electrochemical (EC) detection for quantification. The limit of detection (LOD) of 2,4- and 2,6-TDI was 0.01 microtg ml(-1) for a 20 microl injection. The precision of sample preparation, expressed as the relative standard deviation (RSD), was 0.6% with UV detection and 0.8% with EC detection at a 2,4-TDI concentration of 0.2 microg ml(-1) (n = 6). For 2,6-TDI, the corresponding RSDs were 0.5% and 0.8%. The urinary 2,4- and 2,6-TDA metabolites were determined after acid hydrolysis as heptafluorobutyric anhydride derivatives by gas chromatography-mass spectrometry. The LOD in urine was 0.35 nmol l(-1) for 2,4-TDA and 0.04 nmol l(-1) for 2,6-TDA. The precision (RSD) of six analyses of human urine spiked to a concentration of 100 nmol l(-1) was 3.7% for 2,4-TDA and 3.6% for 2,6-TDA. There was a trend for linear correlation between urinary TDA concentration and the product of airborne TDI concentration and sampling time. Urinalysis of TDA is proposed as a practical method for assessing personal exposures in workers exposed intermittently to TDI.     

Determination of unreacted 2,4-toluene diisocyanate (2,4TDI) and 2,6-toluene diisocyanate (2,6TDI) in foams at ultratrace level by using HPLC-CIS-MS-MS

Isocyanates can cause occupational asthma. By using available HPLC-UVF methods, isocyanates can be quantified only at levels above 1% of the Permissible Exposure Limits (PEL). Once sensitized, workers can react to concentrations below these limits of detection (LOD) making these methods insufficiently sensitive to adequately evaluate trace amounts of isocyanates present in air or in materials at safe levels for sensitized workers. This article describes a novel method for isocyanate analysis allowing the quantification of 2,4TDI and 2,6TDI monomers at very low concentrations using HPLC-CIS-MS-MS. The method's sensitivity increases with a decrease in the alkali radius. The LOD is 0.039 ng mL(-1) for 2,4TDI and 0.100 ng mL(-1) for 2,6TDI in solution when lithium is the alkali adduct, which is 20 times more sensitive than HPLC-UVF method. This new method allows determination in foam at levels of 0.078 ng g(-1) for 2,4TDI and 0.200 ng g(-1) for 2,6TDI respectively, for a 0.5 g foam sample. This is more than 100 times more sensitive than other methods for determining free monomers in solid materials. Analytical reproducibility and precision are better than 92% and 93% for both diisocyanate monomers. The use of HPLC-UVF conventional method failed to detect unreacted isocyanates in foam samples, but TDI monomers were quantified by HPLC-CIS-MS-MS.     

Condenser-type diffusion denuders for the collection of sulfur dioxide in a cleanroom

High-efficiency condenser-type diffusion denuders of cylindrical and planar geometries are described. The film condensation of water vapor onto a cooled denuder surface can be used as a method for collecting water-soluble gases. By using SO(2) as the test gas, the planar design offers quantitative collection efficiency at air sampling rates up to 5 L min(-1). Coupled to ion chromatography, the limit of detection (LOD) for SO(2) is 0.014 ppbv with a 30-min successive analysis sequence. The method has been successfully applied to the analysis of temperature- and humidity-controlled cleanroom air.     

Determination of nitric acid in ambient air using diffusion denuder tubes

A method has been developed for the determination of gaseous nitric acid in air based on its separation from particulate nitrate aerosol using diffusion denuder tubes. An integrated value of nitric acid concentration in air is obtained. The experimentally derived absorption efficiencies of the diffusion denuder tubes ranged from 87.6 to 96.9%. The standard deviation of the method was calculated as 0.10 mug/m(3) for nitric acid concentrations in the range 0.54-1.72 mug/m(3). A correction procedure, using two diffusion denuders in series, should be applied if measurements are made in the presence of high levels of nitrogen oxides.     

涂布2,4-二硝基苯肼的环形溶蚀器/滤膜系统和高效液相色谱法检测大气中二羰基化合物

建立了环形溶蚀器/滤膜系统(Annular denuder/filter pack system)和2,4-二硝基苯肼(DNPH)-高效液相色谱法(HPLC)采集和检测大气中气相和颗粒相二羰基化合物的方法。DNPH作为吸附剂分别涂布在环形溶蚀器的内壁和3层滤膜上,当大气样品经过环形溶蚀器时,含有气相二羰基化合物的气体吸附到环形溶蚀管内壁上与DN-PH发生反应,而颗粒相部分穿过环形溶蚀管,采集到滤膜上。样品经乙腈洗脱、浓缩后,采用HPLC进行分析。根据不同的采样流速、采样时间和DNPH的涂布量采集到的二羰基化合物的浓度,确定的最佳采样条件为:采样流速4 L/min,采样时间4~5 h,DNPH浓度0.47 g/L。使用Tedlar bag验证环形溶蚀器乙二醛和甲基乙二醛的采集效率(分别为82%和85%)。利用此方法对实际大气中的二羰基化合物进行了检测。     

A solvent-free sampling method for airborne toluene diisocyanate

Summary A useful method of sampling and measurement of toluene diisocyanate concentration in atmosphere is described. The sampler consists of glass-fibre filters impregnated with the reagent 1-(2-methoxyphenyl)piperazine¹ so that the 2,4 and 2,6 isomers of TDI react to form urea derivatives which are analysed by high performance liquid chromatography in isocratic mode on cyan-amino and C₁₈ bonded phases. A dynamic system was used to generate standard atmospheres of TDI and to validate the sampling method within the humidity range of 0% to 75%. A coated filter, a bubbling solution and an impregnated silica gel were compared as samplers requiring the piperazine reagent in performance experiments.     

Prediction of gas collection efficiency and particle collection artifact for atmospheric semivolatile organic compounds in multicapillary denuders

A modeling approach is presented to predict the sorptive sampling collection efficiency of gaseous semivolatile organic compounds (SOCs) and the artifact caused by collection of particle-associated SOCs in multicapillary diffusion denuders containing polydimethylsiloxane (PDMS) stationary phase. Approaches are presented to estimate the equilibrium PDMS–gas partition coefficient (K_pdms) from a solvation parameter model for any compound, and, for nonpolar compounds, from the octanol–air partition coefficient (K_oa) if measured K_pdms values are not available. These estimated K_pdms values are compared with K_pdms measured by gas chromatography. Breakthrough fraction was measured for SOCs collected from ambient air using high-flow (300 L min⁻¹) and low-flow (13 L min⁻¹) denuders under a range of sampling conditions (−10 to 25 °C; 11–100% relative humidity). Measured breakthrough fraction agreed with predictions based on frontal chromatography theory using K_pdms and equations of Golay, Lövkvist and Jönsson within measurement precision. Analytes included hexachlorobenzene, 144 polychlorinated biphenyl congeners, and polybrominated diphenyl ethers 47 and 99. Atmospheric particle transmission efficiency was measured for the high-flow denuder (0.037–6.3 μm diameter), and low-flow denuder (0.015–3.1 μm diameter). Particle transmission predicted using equations of Gormley and Kennedy, Pich, and a modified filter model, agreed within measurement precision (high-flow denuder) or were slightly greater than (low-flow denuder) measured particle transmission. As an example application of the model, breakthrough volume and particle collection artifact for the two denuder designs were predicted as a function of K_oa for nonpolar SOCs. The modeling approach is a necessary tool for the design and use of denuders for sorptive sampling with PDMS stationary phase.     

Performance of a 2,4-DNPH coated annular denuder/HPLC system for formaldehyde monitoring in air

Summary The performance of annular denuders coated with 2,4-dinitrophenylhydrazine for collection of atmospheric HCHO has been evaluated by HPLC/UV analysis of samples coming from laboratory tests and field experiments. A number of parameters, such as collection efficiency at varying air humidity, detection limit, operative capacity and temporal self-consistency have been investigated to optimize the denuder behaviour under different weather conditions and to obtain short-term concentration profiles of HCHO. Deviations between measurements made simultaneously by the DNPH denuder method and differential optical absorption spectrometry (DOAS) have been found to average approximately 30% in the 0–5 ppb HCHO concentration range.     

Trace analysis of airborne aromatic isocyanates and related aminoisocyanates and diamines using high-performance liquid chromatography with ultraviolet and electrochemical detection

A high-performance liquid chromatographic method was developed for trace analysis of complex air mixtures containing 2,6- and 2,4-toluenediisocyanates and related aminoisocyanates and diamines. The accuracy was tested at isocyanate concentrations of 2-1000 microg/m3 in air. The method is based on derivatization in the sampling step of isocyanate functions to corresponding urethane groups, with alkaline ethanol as the sampling and reacting medium. The derivatives formed, toluenediurethanes and tolueneaminourethanes, and unreacted diamines were detected by UV or electrochemically, the electrochemical detection being one order of magnitude more sensitive. Using an enrichment column, detection limits of ca. 0.05 pg/microl were obtained with electrochemical detection at a potential of 950 mV, which corresponds to air concentrations of 0.1 microg/m3 with 5 min sampling time at a rate of 11/min. The precision in the measurements were ca. 4% at concentrations of 6 microg/m3. A field measurement was performed concerning flame lamination of toluenediisocyanate-based polyurethane and cloth. Isocyanates, aminoisocyanates and diamines were found at air concentrations of 1-100 microg/m3.     

Study of slabstock flexible polyurethane foams based on varied toluene diisocyanate isomer ratios

The morphological features of three flexible slabstock polyurethane foams based on varied contents of 2,4 and 2,6 toluene diisocyanate (TDI) isomers are investigated. The three commercially available TDI mixtures, that is, 65:35 2,4/2,6 TDI, 80:20 2,4/2,6 TDI, and 100:0 2,4/2,6 TDI were used. The foams were characterized at different length scales with several techniques. Differences in the cellular structure of the foams were noted with scanning electron microscopy. Small‐angle X‐ray scattering was used to demonstrate that all three foams were microphase‐separated and possessed similar interdomain spacings. Transmission electron microscopy revealed that the aggregation of the urea phase into large urea‐rich regions decreased systematically on increasing the asymmetric TDI isomer content. Fourier transform infrared spectroscopy showed that the level of bidentate hydrogen bonding of the hard segments increased with the 2,6 TDI isomer content. Differential scanning calorimetry and dynamic mechanical analysis (DMA) were used to note changes in the soft‐segment glass‐transition temperature of the foams on varying the diisocyanate ratios and suggested that the perfection of microphase separation was enhanced on increasing the 2,6 TDI isomer content. The preceding observations were used to explain why the foam containing the highest content of the symmetric 2,6 TDI isomer exhibited the highest rubbery storage modulus, as measured by DMA. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 258–268, 2003     

Investigation of a cylindrical chemosorptive denuder for sampling and phase separation of toluene diisocyanate aerosols

A cylindrical chemosorptive denuder in series with a glass fibre filter has been evaluated for sampling toluene diisocyanate (TDI) aerosols. The sampler is designed for measuring personal exposure to diisocyanates. Several denuder coatings and derivatising reagents were investigated. Dimethylpolysiloxane (SE-30) and 5% phenyl dimethylpolysiloxane (SE-54) with either dibutylamine (DBA) or dipentylamine (DPeA) as derivatising reagents yielded the lowest vapour breakthrough (the amount (%) of the vapour that passes through the denuder), close to values predicted by theory. Immobilisation of the SE-30 denuder coating by in-situ cross-linking yielded comparable results. With an SE-30/DBA-coated denuder operating within an airflow range of 100–500 mL min^–1, the phase separation was shown to be consistent with theoretical predictions derived by use of the Gormley–Kennedy equation. This provides a means of calculating the vapour breakthrough and correcting experimentally obtained values with regard to vapour–particulate phase distribution, suggesting that the denuder can provide accurate phase-distribution measurements. The SE-30/DBA denuder can be used over a concentration range spanning nearly six orders of magnitude. Its capacity is sufficient to perform 15-min exposure measurements of a TDI aerosol with air concentrations as high as 1,700 g m^–3, 40 times higher than the Swedish occupational exposure limit (OEL). At the other end of the range, the estimated limit of detection (LOD) was less than 2 ng m^–3 for both the vapour and the aerosol phases when LC–ESI–MS–MS was used for chemical analysis.Electronic Supplementary Material Supplementary material for this article is available at     

Simultaneous measurements of formaldehyde and ozone in air by annular denuder-HPLC techniques

Summary A denuder sampling method combined with HPLC analysis for the simultaneous determination of formaldehyde and ozone in ambient air is described. It is based on the reactions of CH₂O and O₃ with 2,4-dinitrophenylhydrazine (DNPH) and 4-allyl-2-methoxyphenol (eugenol)_respectively, both acting as coatings of two annular denuders connected in series. Formaldehyde released from the ozonolysis of eugenol is quantitatively collected on a third downstream DNPH-coated denuder. The two DNPH denuders are then extracted and analyzed as hydrazone derivative by HPLC with UV absorbance detection.The stoichiometric factor of the eugenol-ozone reaction was found to be 2.0±0.1 moles of O₃ per mole of CH₂O. The limits of detection are 0.8gm^–3 CH₂O and 3gm^–3 O₃ for 100l air sampled, corresponding to 1-h sampling at 1.7l min^–1.     

Gas collection efficiency of annular denuders: A spreadsheet-based calculator

Denuders are widely used for atmospheric analysis. Annular denuders are especially well-suited for preconcentration of trace gases compared to simpler single tube designs. While traditionally coated annular denuders have both bounding surfaces that behave as sinks, annular denuders/membrane-based scrubbers with the same basic geometric design and with only one of the annular surfaces functioning as sink (e.g., a membrane tube whose outer surface behaves as a sink disposed within an inert jacket tube) have become common. However, the gas collection efficiency of such devices cannot be expressed as a simple equation with fixed constants and there is no presently available tool to a priori determine the denuder performance or to design denuders with specific removal efficiencies at specific sampling rates. This paper presents a simple to use “spreadsheet calculator” for concentric annular denuders of any dimension based on known solutions to analogous heat transfer problems. The results from the present spreadsheet calculator are compared with results from a commercial computational fluid dynamics package (Fluent™; this takes significant expertise and development effort to run)—the two approaches produce essentially the same results. The present spreadsheet calculator can be used easily and simply without training and will be a useful tool for denuder users and designers.     

Critical evaluation of adsorption-based sampling of vaporized metal species in flue gases

Diffusion-controlled sampling techniques, i.e. diffusion screens and diffusion tubes (= denuders), can be used in the collection of several vaporized heavy metal species in clean gases (pure N₂ atmosphere) at elevated temperatures. Collection efficiencies obtained for Hg, HgCl₂, Cd, CdCl₂ and ZnCl₂ were over 90% using adsorption on Au-coated diffusion screens and Ag-coated denuders. However, the collection efficiencies for Zn and PbCl₂ were significantly lower. In field measurements performed at a hazardous waste incineration plant and in a power plant equipped with a circulating fluidized-bed boiler, collection efficiencies seemed to vary noticeably depending on the sampling conditions and metal species to be sampled. Best collection efficiencies were obtained for mercury with both Ag coated denuders and Au coated screens whereas cadmium showed significantly poorer results in field measurements than in the laboratory. Sampling of zinc and lead species seemed to be problematic in all cases. Of the two sampling techniques, the denuder technique is more recommendable than the screen technique for sampling in relatively clean gases. However, neither of these techniques should be used in flue gases without further understanding of the collection mechanisms. Received: 6 November 1996 / Revised: 3 July 1996 / Accepted: 14 July 1996     

Determination of tocopherols,tocopherolquinones and tocopherolhydroquinones by gas chromatography-mass spectrometry and preseparation with lipophilic gel chromatography

A method has been developed for the simultaneous determination of a range of aromatic amines using cation-exchange chromatography performed on a standard ion chromatography column using d.c. amperometric detection. The analytes separated were 2,4- and 2,6-toluenediamine (2,4- and 2,6-TDA), aniline, o-toluidine, benzidine, p-chloroaniline, 4,4'-diaminodiphenyl (4,4'-DDP), m-nitroaniline and 1-naphthylamine. A Dionex CS12 column was used with gradient elution from an initial eluent of 5% CH3CN+35 mM H2SO4 to 27% CH3CN+35 mM H2SO4 (at 35 min). Detection limits in the range 2.6-22.6 microg/l were observed for all analytes except m-nitroaniline, for which the detection limit was 201 microg/l. Linear calibrations and good precision were observed and the method was applied to the determination of benzidine, p-chloroaniline and 1-naphthylamine in wastewater samples. Further, the separation was also used (after some modification of the eluent conditions) for the determination of 2,4- and 2,6-toluene diisocyanate (2,4- and 2,6-TDI) and 4,4'-methylenediphenyl diisocyanate (4,4'-MDI) after their hydrolysis to 2,4-TDA, 2,6-TDA and 4,4'-DDP. Detection limits for 2,6- and 2,4-TDI and 4,4'-MDI were 3.8, 8.2, and 11.2 microg/l, respectively. The method was applied to the determination of diisocyanates in air.     

Improved determination of gaseous divalent mercury in ambient air using KCl coated denuders

An improved method for the determination of gaseous divalent mercury (GDM) in ambient air using KCl coated denuders has been developed and tested. GDM collected in the KCl coated denuders can be quantitatively desorbed at 450 degrees C in 10 min. After being complete thermally reduced to Hg0 at 900 degrees C, all mercury released from the denuder is pre-concentrated on the analytical Au trap, and detected by cold vapor atomic fluorescence spectrometry (CVAFS). The absolute detection limit of the method is less than 3 pg. Preliminary data of GDM concentration in ambient air from different sampling stations show that GDM concentrations in the urban air of G?teborg are much higher than in rural air (R?rvik and Sasetta), which indicates the anthropogenic origin of GDM.     

Improved determination of gaseous divalent mercury in ambient air using KCl coated denuders

An improved method for the determination of gaseous divalent mercury (GDM) in ambient air using KCl coated denuders has been developed and tested. GDM collected in the KCl coated denuders can be quantitatively desorbed at 450?°C in 10 min. After being complete thermally reduced to Hg⁰ at 900?°C, all mercury released from the denuder is pre-concentrated on the analytical Au trap, and detected by cold vapor atomic fluorescence spectrometry (CVAFS). The absolute detection limit of the method is less than 3 pg. Preliminary data of GDM concentration in ambient air from different sampling stations show that GDM concentrations in the urban air of Göteborg are much higher than in rural air (Rörvik and Sasetta), which indicates the anthropogenic origin of GDM.     

Determination of gaseous toluene diisocyanate by use of solid-phase microextraction with on-fibre derivatisation

An SPME method was developed for sampling gaseous 2,4-toluene diisocyanate (2,4-TDI) involving derivatisation of the isocyanate by reacting with dibutylamine (DBA). The TDI-DBA derivative thus formed was determined by LC-MS-MS utilising atmospheric pressure chemical ionisation (APCI). As a first step, DBA was loaded onto a poly(dimethylsiloxane)/divinylbenzene (PDMS-DVB) fibre coating by direct vapour-phase extraction of a highly concentrated diethyl ether solution of DBA. The DBA-loaded fibre was then exposed to an artificially generated atmosphere of gaseous 2,4-TDI. The linearity of the method ranged from 52.8 to 3100 microg m(-3) (6.8 to 400 ppbv) with a sampling time of 60 min. The proposed method has been applied to 2,4-TDI determination in an artificially generated dynamic standard atmosphere, yielding an approximate method detection limit (MDL) of 2 microg m(-3) (0.25 ppbv). This concentration is one twentieth of the Occupational Safety and Health Administration (OSHA) 8-hour time-weighted average (TWA) exposure limit. The sampler with the PDMS-DVB-DBA coating was found to be stable and retains the required amount of DBA for at least 10 days, an important feature for sampling systems with potential in-situ applications.     

Direct thermal desorption of semivolatile organic compounds from diffusion denuders and gas chromatographic analysis for trace concentration measurement

A novel method for collection and analysis of vapor-phase semivolatile organic compounds (SOCs) in ambient air is presented. The method utilizes thermal desorption of SOCs trapped in diffusion denuders coupled with cryogenic preconcentration on Tenax-TA and analysis by high resolution gas chromatography (GC)-electron-capture detection (ECD). The sampling and analysis methods employ custom-fabricated multicapillary diffusion denuders, a hot gas spike (HGS) apparatus to load known quantities of thermally stable standards into diffusion denuders prior to sample collection, a custom-fabricated oven to thermally desorb SOCs from the diffusion denuder, and a programmable temperature vaporization (PTV) inlet containing a liner packed with Tenax-TA for effective preconcentration of the analytes and water management. High flow rates into the PTV inlet of 750mLmin(-1)during thermal desorption are ca. a factor of ten greater than typically used. To improve resolution and retention time stability, the thermal desorption and PTV inlet programming procedure includes three steps to prevent water from entering the analytic column while effectively transferring the analytes into the GC system. The instrumentation and procedures provide virtually complete and consistent transfer of analytes collected from ambient air into the GC evidenced by recovery of seven replicates of four internal standards of 90.7+/-4.0-120+/-23% (mean+/-95% confidence interval, CI). Retention time based compound identification is facilitated by low retention time variability with an average 95% CI of 0.024min for sixteen replicates of eight standards. Procedure details and performance metrics as well as ambient sampling results are presented.