Identification and determination of mycotoxins and food additives in feed by HPLC–high-resolution time-of-flight mass spectrometry

High-resolution time-of-flight mass spectrometry combined with high performance liquid chromatography is proposed for the detection and determination of 25 mycotoxins and 8 food additives (coccidiostats) in animal feed, using simplified and rapid sample preparation. We developed a procedure for the identification and determination of analytes by the standard addition method. The lower limit of the analytical range is 1 (400) µg/kg for mycotoxins; the analytical range for coccidiostats in feed is 10–200 mg/kg. The relative standard deviation of the results does not exceed 10%. The analysis time is 0.5–1 h.     

Analysis of antimicrobial agents in animal feed

We review current trends in the analysis of antimicrobial agents in animal feeds. After a brief introduction to feed-industry figures and the unavoidable problem of cross-contamination, we provide an overview of the European Union legislative framework for feedingstuffs. We devote the core of the article to analytical methodology developed over the past 10 years for monitoring residues of antibiotics and coccidiostats in feedingstuffs in order to ensure that feeds comply with current legislation and are of high quality and safety for both livestock and consumers. We consider the potential and the limitations of analytical methods and devote special attention to their validation and performance characteristics.     

Development of a five-plex flow cytometric immunoassay for the simultaneous detection of six coccidiostats in feed and eggs

Coccidiostats are the only veterinary drugs still permitted to be used as feed additives to treat poultry for coccidiosis. To protect consumers, maximum levels for their presence in food and feed have been set by the European Union (EU). To monitor these coccidiostats, a rapid and inexpensive screening method would be a useful tool. The development of such a screening method, using a flow cytometry-based immunoassay, is described. The assay uses five sets of colour-coded paramagnetic microspheres for the detection of six selected priority coccidiostats. Different coccidiostats, with and without carrier proteins, were covalently coupled onto different bead sets and tested in combination with polyclonal antisera and with a fluorescent-labelled secondary antibody. The five optimal combinations were selected for this multiplex and a simple-to-use sample extraction method was applied for screening blank and spiked eggs and feed samples. A very good correlation (r ranging from 0.995 to 0.999) was obtained with the responses obtained in two different flow cytometers (Luminex 100 and FLEXMAP 3D). The sensitivities obtained were in accordance with the levels set by the EU as the measured limits of detection for narasin/salinomycin, lasalocid, diclazuril, nicarbazin (4,4'-dinitrocarbanilide) and monensin in eggs were 0.01, 0.1, 0.5, 53 and 0.1 μg/kg and in feed 0.1, 0.2, 0.3, 9 and 1.5 μg/kg, respectively.     

Analysis of fluoroquinolones in animal feeds by liquid chromatography with fluorescence detection

An analytical method for the analysis of six fluoroquinolones (FQs) in animal feeds was developed. The sample treatment consists of a simple and rapid extraction of the analytes by manual shaking with an acetonitrile-water mixture containing hydrochloric acid without further sample cleanup. Matrix effects were minimized by diluting the extract with water. Determination was carried out by liquid chromatography using fluorimetric detection. The method was validated in-house in four different feed matrices (poultry, cow, pig, and lamb feed). Mean recoveries ranging from 80 to 105%, with relative standard deviations below 12%, were achieved from spiked animal feed samples on the 0.2-2.0 μg/g level. No relevant differences were observed between the studied feeds, this ensuring that the method was reliable for a wide variety of feed matrices. Decision limit and detection capability values are below 0.08 and 0.13 mg/kg, respectively, for most FQs. The results obtained demonstrate the feasibility of the analytical method developed for a routine use to control the illegal use of these substances in feeding stuffs.     

Analytical strategies for residue analysis of veterinary drugs and growth-promoting agents in food-producing animals--a review

After a brief introduction into the field of veterinary drugs and growth-promoting agents, the most important EU regulations and directives for the inspection of food-producing animals and animal products regarding the residue control of these substances are presented and discussed. Main attention in the review is on the methods of analysis in use today for the most important classes of veterinary drugs and growth-promoting agents viz. anthelmintics, antibiotics, coccidiostats, hormones, beta-agonists and tranquillizers. Emphasis is given to the potential, and limitations, of state-of-the-art analytical procedures and their performance characteristics. The most obvious conclusion is that, today (reversed-phase) liquid chromatography combined with tandem mass spectrometric detection--either triple-quadrupole or ion-trap multi-stage--is the preferred technique in a large majority of all cases. In the field of sample treatment, the combined use of liquid extraction--i.e., liquid partitioning or liquid-liquid extraction--and liquid-solid extraction--primary on- or off-line solid-phase extraction--is most popular. Finally, while the analytical tools required to meet the demands typically formulated by governments and international organizations today, generally speaking are available, several problems still do exist. To quote three examples, problems are encountered in the area of simultaneously extracting and pre-treating groups of analytes with mutually widely different polarities, with regard to identification-point--based confirmation of analyte identity, and regarding quantification errors caused by ion-suppression effects. Improving the speed of analysis is another aspect that should, and will, receive dedicated interest in the near future.     

A European perspective on progress in moving away from the mouse bioassay for marine-toxin analysis

This review considers the ethical and technical problems currently associated with employing mouse bioassays for marine-toxin analysis and the challenges and the difficulties that alternative methods must overcome before being deemed applicable for implementation into a regulatory monitoring regime. We discuss proposed alternative methods, classified as functional, immunological and analytical, for well-established European toxins as well as emerging toxins in European waters, highlighting their advantages and disadvantages. We also consider emerging tools and technologies for future toxin analysis.Even though regulatory bodies have recently recommended analytical methods for a number of toxins, there is still scope for functional and immunological methods in rapid screening and detecting emerging toxins. Future developments foreseen in the analysis of marine biotoxins are multiplex-based analysis, miniaturization and portability for on-site testing. However, the longstanding lack of reference materials and standards continues to pose a severe limitation on progress in development, validation and therefore implementation of any alternative method based on the criteria stipulated by European Union legislation.     

Performance evaluation on a wide set of matrix-assisted laser desorption ionization matrices for the detection of oligosaccharides in a high-throughput mass spectrometric screening of carbohydrate depolymerizing enzymes

Compared to other analytical methods, matrix-assisted laser desorption ionization mass spectrometry (MALDI-MS) presents several unique advantages for the structural characterization of degradation products of carbohydrates. Our final goal is to implement this technique as a high-throughput platform, with the aim of exploring natural bio-diversity to discover new carbohydrate depolymerizing enzymes. In this approach, a variety of carbohydrates will be used as enzymes substrates and MALDI-MS will be employed to monitor the oligosaccharides produced. One drawback of MALDI, however, is that the choice of the matrix is largely dependent on the chemical properties of the analyte. In this context, our objective in the present work was to find the smallest set of MALDI matrices able to detect chemically heterogeneous oligosaccharides. This was done through the performance evaluation of more than 40 MALDI matrices preparations. Homogeneity of analyte-matrix deposits was considered as a critical feature, especially since the final objective is to fully automate the analyses. Evaluation of the matrices was done by means of a rigorous statistical approach. Amongst all tested compounds, our work proposes the use of the DHB/DMA ionic matrix as the most generic matrix, for rapid detection of a variety of polysaccharides including neutral, anionic, methylated, sulfated, and acetylated compounds. The selected matrices were then used to screen crude bacterial incubation media for the detection of enzymatic degradation products.     

Rapid Methods in Analytical Chemistry

This article presents the most recent research in analytical chemistry concerning the development of rapid methodologies covering the period from 2009 up until today. In this context, different useful analytical methods have been developed based mainly on typical techniques such as gas chromatography, liquid chromatography, mass spectrometry, electrophoresis, electroanalytical chemistry, and biosensors. The analytical features of these methods have allowed the analysis of samples of different natures, such as environmental, food, pharmaceutical, and biological type, in which wide classes of analytes are promptly determined. The main advantages of these methods are included and discussed in this review regarding novelty, rapidity, sensitivity, selectivity, and costs. It is concluded that the development of rapid methods is still a growing trend in analytical chemistry and that gas- and liquid-chromatography mainly coupled to different modes of mass spectrometry are the most common analytical techniques applied today. Regarding the matrices analyzed, most of the methods have been developed for food analysis, followed by biological and environmental matrices.     

LC–MS/MS analysis of coccidiostats in meat supply chain safety

The presence of coccidiostats in meat products represents an important topic because of the animal administration of these substances, authorized as feed additives for targeted species, in order to prevent and inhibit coccidiosis. Coccidiostats include both ionophores and synthetic molecules characterized by different chemical–physical properties such as polarity. Meat is a matrix characterized by many interfering compound groups, such as proteins, phospholipids, and fats. High-performance liquid chromatography (HPLC) coupled to mass spectrometry (MS) analysis allows the required selectivity and sensitivity for discriminating analytes and matrix interferences. For these reasons, an LC–MS/MS method for the analysis of coccidiostats in meat products was developed without SPE purification steps. The correct analyte quantification is allowed by matrix-matched calibration. The method validation was performed by the replicated analysis of spiked meat samples at two different concentration levels (limit of quantification—LOQ—and a 10 times LOQ) in order to evaluate method recovery and repeatability, plus spiked samples at higher concentrations up to 10,000 μg/kg. Moreover, the metrological approach was used for the calculation of method uncertainty. The application of the developed method to real samples evidenced the presence of some non-ionophores coccidiostats in the meat and liver of chicken and rabbit species. Although, the determined concentration was below the established MRLs, the monitoring of coccidiostats in the meat supply chain is confirmed as a good strategy in order to safeguard consumer health.     

Substoichiometeric determination of traces of molybdenum by neutron activation analysis

A rapid, simple activation method for the selective determination of traces of molybdenum is proposed. With substoichiometric reagent addition, the required element need not be isolated in a weighable form and the chemical yield need not be determined. Molybdenum is simultaneously separated not only from metal impurities but also from the bulk of matrices such as germanium     

Single-laboratory validation of a multiplex flow cytometric immunoassay for the simultaneous detection of coccidiostats in eggs and feed

Coccidiostats are authorized in the European Union (EU) to be used as poultry feed additives. Maximum (residue) levels (M(R)Ls) have been set within the EU for consumer and animal protection against unintended carry-over, and monitoring is compulsory. This paper describes the single-laboratory validation of a previously developed multiplex flow cytometric immunoassay (FCIA) as screening method for coccidiostats in eggs and feed and provides and compares different approaches for the calculation of the cut-off levels which are not described in detail within Commission Decision 2002/657/EC. Comparable results were obtained between the statistical (reference) approach and the rapid approaches. With the most rapid approach, the cut-off levels for narasin/salinomycin, lasalocid, diclazuril, nicarbazin (DNC) and monensin in egg, calculated as percentages of inhibition (%B/B0), were 60, 32, 76, 80 and 84, respectively. In feed, the cut-off levels for narasin/salinomycin, lasalocid, nicarbazin (DNC) and monensin were 70, 64, 72 and 78, respectively, and could not be determined for diclazuril. For all analytes, except for diclazuril in feed, the rate of false positives (false non-compliant) in blank samples was lower than 1 %, and the rate of false negatives (false compliant) at the M(R)Ls was below 5 %. Additionally, very good correlations (r ranging from 0.994 to 0.9994) were observed between two different analysers, a sophisticated flow cytometer (FlexMAP 3D^®) and a more cost-efficient and transportable planar imaging detector (MAGPIX^®), hence demonstrating adequate transferability.     

Quality assurance and statistical control

In scientific research laboratories it is rarely possible to use quality assurance schemes, developed for large-scale analysis. Instead methods have been developed to control the quality of modest numbers of analytical results by relying on statistical control: Analysis of precision serves to detect analytical errors by comparing thea priori precision of the analytical results with the actual variability observed among replicates or duplicates. The method relies on the chi-square distribution to detect excess variability and is quite sensitive even for 5–10 results. Interference control serves to detect analytical bias by comparing results obtained by two different analytical methods, each relying on a different detection principle and therefore exhibiting different influence from matrix elements; only 5–10 sets of results are required to establish whether a regression line passes through the origo. Calibration control is an essential link in the traceability of results. Only one or two samples of pure solid or aqueous standards with accurately known content need to be analyzed. Verification is carried out by analyzing certified reference materials from BCR, NIST, or others; their limited accuracy of 5–10% make them less suitable for calibration purposes.     

Mass spectrometry in bioresorbable polymer development,degradation and drug‐release tracking

A detailed characterization of polymeric matrices and appropriate degradation monitoring techniques are required to sustain the development of new materials as well as to enlarge the applications of the old ones. In fact, polymer analysis is essential for the clarification of the intrinsic relationship between structure and properties that ascertains the industrial applications in diverse fields. In bioresorbable and biodegradable polymers, the role of analytical methods is dual since it is pointed both at the polymeric matrices and at degradation tracking. The structural architectures, the mechanical and morphological properties, and the degradation rate, are of outstanding importance for a specific application. In some cases, the complexity of the polymer structure, the processes of decomposition or the low concentration of the degradation products need the concurrent use of different complementary analytical techniques to give detailed information of the reactions taking place. Several analytical methods are used in bioresorbable polymer development and degradation tracking. Among them, mass spectrometry (MS) plays an essential role and it is used to refine polymer syntheses, for its high sensitivity, to highlight degradation mechanism by detecting compounds present in trace amounts, or to track the degradation product profile and to study drug release. In fact, elucidation of reaction mechanisms and polymer structure, attesting to the purity and detecting defects as well as residual catalysts, in biodegradable and bioresorbable polymers, requires sensitive analytical characterization methods that are essential in providing an assurance of safety, efficacy and quality. This review aims to provide an overview of the MS strategies used to support research and development of resorbable polymers as well as to investigate their degradation mechanisms. It is focused on the most significant studies concerning synthetic bioresorbable matrices (polylactide, polyglycolide and their copolymers, polyhydroxybutyrate, etc.), published in the last ten years.     

Determination of nicarbazin and clopidol in poultry feeds by liquid chromatography

A rapid and very effective analytical procedure for the simultaneous liquid chromatographic determination of two coccidiostats, clopidol (CLOP) and nicarbazin (NICA), in poultry feeds was developed and tested. The ground feed samples were extracted using aqueous dimethylformamide after moistening with water. Co-extracted feed constituents were removed with a solid-phase extraction alumina-basic column and the eluates were directly analyzed on an ODS column (250x4.6 mm, 5 microm) with acetonitrile-0.01 M acetate buffer (pH 4.6) as eluent. UV detection of CLOP and the 4,4'-dinitrocarbanilide portion of NICA was carried out at 265 and 345 nm, respectively. The mean recovery from NICA spiked samples was 95% with a RSD of 4% in a concentration range of 2-150 mg/kg while for CLOP it was 98% with a RSD of 5% in a concentration range of 5-150 mg/kg. The limits of detection of NICA and CLOP in feed, based on a detector signal-to-noise ratio of 3, were estimated to be 1 mg/kg and 2.5 mg/kg, respectively, and the lowest levels tested in feeds by this procedure were 2 mg/kg and 5 mg/kg, respectively.     

Validation of the LacTek test applied to spiked extracts of tissue samples: determination of performance characteristics

LacTek tests are competitive enzyme-linked immunosorbent assays intended for rapid detection of antimicrobial residues in bovine milk. In this study, the LacTek test protocol was modified for use with extracts of bovine tissue to detect beta-lactam, tetracycline, and sulfamethazine residues. Test performance characteristics--precision, accuracy, ruggedness, practicability, and analytical specificity and sensitivity--were investigated. Results suggest that LacTek tests can be easily adapted to detect antimicrobial residues in extracts of lean ground beef. However, positive samples may not contain residues at violative concentrations (i.e., Canadian maximum residue limits), and therefore, additional analysis would be required for final confirmation and quantitation (e.g., chromatography).     

Electroanalytical methods based on bimetallic nanomaterials for determination of pesticides: Past,present, and future

The excessive use of pesticides in agricultural or non-agricultural fields causes the emergence of environmental and human health problems. Therefore, there is a need to develop simple, fast, sensitive, selective, and low-cost methods for analyzing pesticides from different matrices. Although many analysis methods have been developed to determine pesticides, nanomaterial-based electroanalytical methods offer numerous advantages such as rapid and low cost of analysis, low sample volume requirement, field deployability, and miniaturization to improve the performance of the developed methods. Among different nanomaterials, bimetallic nanomaterials such as gold, platinum, palladium, nickel, and iron-based nanomaterials in combination with other metals have been extensively used as electrode modification agents due to their electrocatalytic characteristics and the synergistic effect of two metals. In this review, firstly, the basic information of pesticides and bimetallic nanomaterials was summarized. Properties, synthesize, and architectures of bimetallic nanomaterials and their nanocomposites were explained in detail. Current applications and utilization of bimetallic nanomaterials for pesticides detection were reviewed by selected studies with working range, the limit of detection, sensitivity, analytical application, and some experimental conditions. In conclusion, the current challenges and future trends for analyzing pesticides based on electroanalytical methods combined with bimetallic nanomaterials were highlighted.     

Improvements in methylmercury determination prior to the certification of two tuna fish materials

An account is given of a systematic, collaborative investigation to detect problems and sources of error in the determination of methylmercury (MeHg) in biological samples. The work was done by a group of analytical laboratories under the auspices of the Community Bureau of References (BCR) of the Commission of the European Communities (EC). The paper presents the organization of three intercomparisons on organic mercury in solution and solid matrices, and the results obtained by the participants. The different analytical steps of the methods used (extraction, clean-up, separation, final detection) are compared and assessed.     

Optimization of Adsorbent Layer Type and Developing Solvent in Coccidiostats Sample Preparation with Procedure of Solvent Front Position Extraction

Coccidiostats are drugs used against coccidiosis, a common disease among breeding animals. Their widespread application leads to the appearance of their residues in food, which is potentially harmful for human health and life. The European Union has established limits of concentrations of these drugs in premixtures and food. Nowadays, there are many methods for monitoring coccidiostats’ presence in market products, but their frequent weakness is sample preparation. Solvent Front Position Extraction is a planar chromatography-based sample preparation method that allows for effective assay of samples with coccidiostats when coupled with LC-MS/MS. The purpose of this research was to find common conditions for the effective isolation of eight coccidiostats from biological sample components with both lower and higher retention than the substances of interest. The acquired results were used for effective isolation of monensin and salinomycin from the premixture samples and allowed for their quantitative determination. The application of a semi-automatic device for the development of chromatograms positively impacted the results, confirming the effectiveness of the method for determining coccidiostats in biological samples.     

Cattle breeding: A fast screening procedure to control the bovine fodder contamination

The European Commission has adopted a large number of emergency measures to prevent the spread of the Bovine spongiform encephalopathy (BSE) in the Member States, and among them, a European Regulation prohibits the feeding to ruminants of animal protein and animal feed containing such protein. Aim of this work has been to propose the thermal analysis as a new rapid and sensitive screening tool for a preliminary determination of possible contamination in products destined to bovine growth, since the possibility to screen the samples by a rapid and sensitive tool could reduce the time of analysis required by the actual methodology and could allow the systematic surveillance of bovine feeding, with the official EU methods applied only to positive samples.