Effects of top confinement and diluents on morphology in crystallization of poly(l‐lactic acid) interacting with poly(ethylene oxide)

Effects of top confinement and diluent poly(ethylene oxide) (PEO) on poly(l ‐lactic acid) (PLLA) crystal morphology have been investigated. When crystallized at 120 °C, uncovered neat PLLA sample exhibits higher growth rate ringless spherulites; while the covered sample exhibits lower growth rate ring‐banded spherulites. As PEO is introduced into PLLA, the morphology also undergoes significant changes. For the same T_c,PLLA = 120 °C, the PEO/PLLA blend with PEO composition greater than 25% exhibits ring‐banded patterns even in uncovered sample. However, in much greater PEO composition (>80 wt %), uncovered samples exhibit ring bands diverging into dendritic patterns, while top covered samples tend to maintain the spiral ring‐band patterns. Both PEO inclusion in PLLA and top cover on films impose growth kinetic alterations. Additionally, the top glass cover tends to prevent the lower surface tension PLLA to be accumulated on the surface, resulting in the formation of ring‐band pattern. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1160–1170     

The morphology of poly(vinylidene fluoride) crystallized from blends of poly(vinylidene fluoride) and poly(ethyl acrylate)

A combined optical and electron microscopical study has been carried out of the crystallization habits of poly(vinylidene fluoride) (PVF₂) when it is crystallized from blends with noncrystallizable poly(ethyl acrylate) (PEA). The PVF₂/PEA weight ratios were 0.5/99.5,5/95, and 15/85. Isothermal crystallization upon cooling the blends from the single-phase liquid region was carried out in the range 135–155°C, in which the polymer crystallizes in the α-orthorhombic unit cell form. The 0.5/99.5 blend yielded multilayered and planar lamellar crystals. The lamellae formed at low undercoolings were lozenge shaped and bounded laterally by {110} faces. This habit is prototypical of the dendritic lateral habits exhibited by the crystals grown from the same blend at high undercoolings as well as by the constituent lamellae in the incipient spherulitic aggregates and banded spherulites that formed from the 5/95 and the 15/85 blends, respectively. In contrast with the planar crystals grown from the 0.5/99.5 blend, the formation of the aggregates grown from the 5/95 blend is governed by a conformationally complex motif of dendritic lamellar growth and proliferation. The development of these aggregates is characterized by the twisting of the orientation of lamellae about their preferential b-axis direction of growth, coupled with a fan-like splaying or spreading of lamellae about that axis. The radial growth in the banded spherulites formed from the 15/85 blend is governed by a radially periodic repetition of a similar lamellar twisting/fan-like spreading growth motif whose recurrence corresponds to the extinction band spacing. This motif differs in its fan-like splaying component from banding due to just a helicoidal twisting of lamellae about the radial direction. © 1993 John Wiley & Sons, Inc.     

Periodic extinction bands composed of all flat‐on lamellae in poly(dodecamethylene terephthalate) thin films crystallized at high temperatures

Using in‐house synthesized poly(dodecamethylene terephthalate) (P12T) as a model, periodic extinction‐banded spherulites melt‐crystallized at high T_cs (100–115 °C) are expounded in terms of growth mechanism. The extinction‐banded spherulites wildly differing from the usual blue/orange double ring‐banded spherulites are composed of all flat‐on discrete single‐crystalline lamellae packed like roof shingles (or fish scales) along the circularly curved bands and the lamellae in the extinction bands are flat with a lozenge shape with no continuous twisting at all. For P12T films of more than 10 µm crystallized at T_c = 105–115 °C, no periodic bands were seen, and all spherulites were ringless, where periodic growth precipitation of crystals to extinction does not occur until impingement. Extinction bands in the P12T spherulites with the inter‐ring spacing steadily decrease with decreasing film thickness, because for thinner films (submicrons to 2 µm), draining or depletion of available molten species takes place more frequently, leading to bands of smaller inter‐ring spacing. The petal‐like extinction bands are discussed and analyzed in detail using 3D AFM imaging. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 601–611     

Effects of miscible diluent of poly(ether imide) on ring-banded morphology of poly(trimethylene terephthalate)

The melting, crystallization, and self-packed ring patterns in the spherulites of miscible blends comprising poly(trimethylene terephthalate) (PTT) and poly(ether imide) (PEI) were revealed by optical, scanning electron microscopies (PLM and SEM) and differential scanning calorimetry (DSC). Morphology and melting behavior of the miscible PTT/PEI blends were compared with the neat PTT. Ringed spherulites appeared in the miscible PTT/PEI blends at all crystallization temperatures up to 220 °C, whereas at this high temperature no rings were seen in the neat PTT. A postulation was proposed, and interrelations between rings in spherulites and the multiple lamellae distributions were investigated. The specific interactions and the segregation of amorphous PEI were discussed for interpreting the morphological changes of 220 °C-melt-crystallized PTT/PEI samples. Interlamellar segregation of PEI might be associated with multiple lamellae in the spherulites of PTT/PEI blends; therefore, rings were more easily formed in the PTT/PEI blends at all crystallization temperatures. A postulated model of uneven lamellar growth, coupled with periodical spiraling, more properly describes the possible origin of ring bands from combined effects of both interactions and segregation between the amorphous PEI and PTT in blends.     

Crystallization behavior and hydrophilicity of poly (vinylidene fluoride) (PVDF)/poly (styrene-<Emphasis Type="Italic">co</Emphasis>-acrylonitrile) (SAN) blends

Poly (styrene-co-acrylonitrile) (SAN) is a hydrophilic non-crystalline copolymer, which is initially used in this paper to improve the hydrophilicity of poly (vinylidene fluoride) (PVDF). Investigation of the crystallization behavior of PVDF/SAN blends showed that the samples presented only α phase regardless of SAN content as cooling from the melt. A double-melting phenomenon was related to the perfection or crystal size of PVDF crystals. As the SAN content is increasing, crystallization of PVDF was limited, leading to a decreased crystallinity and lamellar growth. Besides, the hydrophilicity of PVDF was improved by blending with SAN. The sample containing 70 wt.% SAN performed a similar surface property of the neat SAN owing to the besieging of the PVDF phase by SAN. Observed from the cross section of the blends, PVDF/SAN blends were partially miscible with less than 50 wt.% SAN addition. As the SAN content was more than 50 wt.%, the crystalline PVDF particles clearly dispersed in the amorphous matrix.     

Synthesis,morphology, and nonisothermal crystallization behavior of poly(trimethylene terephthalate)/poly(propylene glycol) segmented random copolymers

Poly(trimethylene terephthalate)/poly(propylene glycol) (PTT/PPG) segmented random copolymers were synthesized by melt copolycondensation. The weight fraction of PPG blocks was ranged from 12.1 to 33.4 wt%, which was confirmed by ¹H NMR spectroscopy. The result of wide‐angle X‐ray diffractometer indicated that all copolymers had the same crystal structure of PTT homopolymer at room temperature. At a determined crystallization temperature, ring‐banded spherulites could be observed in all copolymers samples, and the band spacing increased with the increase of PPG content. Morphologies of copolymers after nonisothermal crystallization process were strongly depended on the cooling rate. Well‐defined ring‐banded spherulites can be observed only at moderate cooling (20°C/min), while it was really hard to be observed at too low (2.5°C/min) or too high (by air‐quenching) cooling rate. Moreover, the size of spherulites decreased with the increase of cooling rate. Finally, different nonisothermal crystallization kinetics were adopt to analyze this copolymer system, and only the Mo method was suitable to describe this copolymer system. Copyright © 2016 John Wiley & Sons, Ltd.     

Crystallization kinetics of poly(ethylene oxide) confined in semicrystalline poly(vinylidene) fluoride

Polymer blends based on poly(vinylidene fluoride) (PVDF) and poly(ethylene oxide) (PEO) have been prepared to analyze the crystallization kinetics of poly(ethylene oxide) confined in semicrystalline PVDF with different ratios of both polymers. Both blend components were dissolved in a common solvent, dimethyl formamide. Blend films were obtained by casting from the solution at 70 °C. Thus, PVDF crystals are formed by crystallization from the solution while PEO (which is in the liquid state during the whole process) is confined between PVDF crystallites. The kinetics of crystallization of the confined PEO phase was studied by isothermal and nonisothermal experiments. Fitting of Avrami model to the experimental DSC traces allows a quantitative comparison of the influence of the PVDF/PEO ratio in the blend on the crystallization behavior. The effect of melting and further recrystallization of the PVDF matrix on PEO confinement is also studied. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 588–597     

Rhythmic growth of ring‐banded spherulites in blends of liquid crystalline methoxy‐poly(aryl ether ketone) and poly(aryl ether ether ketone)

Rhythmic growth of ring‐banded spherulites in blends of liquid crystalline methoxy‐poly(aryl ether ketone) (M‐PAEK) and poly(aryl ether ether ketone) (PEEK) has been investigated by means of differential scanning calorimetry (DSC), polarized light microscopy (PLM), and scanning electron microscopy (SEM) techniques. The measurements reveal that the formation of the rhythmically grown ring‐banded spherulites in the M‐PAEK/PEEK blends is strongly dependent on the blend composition. In the M‐PAEK‐rich blends, upon cooling, an unusual ring‐banded spherulite is formed, which is ascribed to structural discontinuity caused by a rhythmic radial growth. For the 50:50 M‐PAEK/PEEK blend, ring‐banded spherulites and individual PEEK spherulites coexist in the system. In the blends with PEEK as the predominant component, M‐PAEK is rejected into the boundary of PEEK spherulites. The cooling rate and crystallization temperature have great effect on the phase behavior, especially the ring‐banded spherulite formation in the blends. In addition, the effects of M‐PAEK phase transition rate and phase separation rate on banded spherulite formation is discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3011–3024, 2007     

Analysis of multiple melting behavior of spherulites comprising ring‐band shell/ringless core in polymorphic poly(butylene adipate)

In‐depth interpretation of ring‐banded spherulitic morphology, crystals, polymorphism, and complex melting behavior in poly(1,4‐butylene adipate) (PBA) were analyzed via a procedure of designing composite core‐shell spherulites, in which two lamellar patterns (ring‐band vs. ringless) were packed by subjecting to crystallization at two‐step temperature schemes with specific temperatures and times. By heating to 52 °C and holding at that temperature for 30 min annealing, the core can be stripped off by melting, and analysis specifically on the ring‐shell portion (with the ringless core stripped by controlled melting) proves that the highest melting peak (P₄ at 55–57 °C) is likely associated with melting of the ring‐band lamellae. Furthermore, the unusually complex multiple melting in PBA can be attributed to all three widely proposed mechanisms: (1) multiple types of lamellae preexisting in crystallized PBA, (2) scan/heating induced remelting/reorganization, and (3) polymorphism of dual crystal cells. In addition, this study evidently shows that the extinction rings within the ring‐banded shell, regardless of alternate edge‐on and flat‐on mechanism or alternative origins, can be of all singly α‐crystal form, either initially or upon postheating temperature‐induced transformation. Thus, the type of crystal forms (α or β) in polymorphic PBA is mainly associated with temperature of crystallization (T_c = 28 or 35 °C), and not likely with lamellar orientation (flat‐on or edge‐on). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 892–899, 2008     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride) (PVDF)/poly(methylmethacrylate) (PMMA)/poly(styrene-<Emphasis Type="Italic">co</Emphasis>-acrylonitrile) (SAN) ternary blends

Compatibilization of the partially miscible poly(vinylidene fluoride) (PVDF)/poly(styrene-co-acrylonitrile) (SAN) pair by a third homopolymer, i.e., poly(methyl methacrylate) (PMMA), was investigated in relation to cross section morphology, crystallization behaviors and hydrophilicity of the polyblends. Scanning electron microscopy showed a more regular and homogeneous morphology when more than 15 wt.% PMMA was incorporated. The samples presented only α phase regardless of PMMA content in the blend. As the PMMA content increased in the blends, the interactions between each component were enhanced, and the crystallization of PVDF was limited, leading to a decreasing of the crystallinity and the crystallite thickness. Besides, the hydrophilicity of PVDF was further improved by PMMA addition. The sample containing 15 wt.% PMMA showed a more hydrophilic property due to the more polar part of surface tension induced by PMMA addition. Observed from the cross section of the blends, the miscibility of partially miscible PVDF/SAN blends were efficiently improved by PMMA incorporation.     

Effect of small amount of poly(ethylene naphthalate) on isothermal crystallization and spherulitic morphology of poly(trimethylene terephthalate)

The effect of a small amount of poly(ethylene naphthalate) (PEN) in its blends with poly(trimethylene terephthalate) (PTT) on isothermal melt-crystallization kinetics and spherulitic morphology of the blends was thoroughly investigated. The maximum PEN content in the blends was 9 wt%. Due to the single composition-dependent glass transition temperature (T_g) that was observed for each blend, these blends appeared to be miscible in the amorphous state. After isothermal crystallization from the melt state, the neat PTT and its blends with PEN exhibited either double or triple melting endotherms. The triple endothermic peaks were observed in both the neat PTT and the blends when being crystallized at crystallization temperatures (T_c) of less than or equal to 195 °C. The equilibrium melting temperature () for the neat PTT was determined based on the linear Hoffman–Weeks extrapolative method to be 248 °C. Such values for the blends were found to decrease with the addition and increasing amount of PEN. Both the neat PTT and the blends were isothermally crystallized over the T_c range of 190–205 °C. At a given T_c, the 97PTT/3PEN blend exhibited a half-time of crystallization (t_0.5) value that was lower, while it exhibited reciprocal half-time (), Avrami rate constant (K_A), and spherulitic growth rate (G) values that were greater, than those of the neat PTT. With further increase in the PEN content, the t_0.5 value increased, while the , K_A, and G values decreased. Analysis of the G values based on the Lauritzen–Hoffman's (LH) secondary nucleation theory showed that the neat PTT and the 91PTT/9PEN blend exhibited a regime II→III transition at 194 °C (467.2 K), while no regime transition was observed for the other two blends. The lateral and the fold surface free energies (σ and σ_e) and the work of chain folding (q) for the neat PTT and the blends were 19.4, 30.2–46.3 erg cm⁻², and 2.4–3.6 kcal mol⁻¹, respectively. Lastly, the effect of both the T_c and the PEN content on morphology and texture of the PTT spherulites was also investigated and the results showed that the texture of the spherulites became coarser with increasing T_c and PEN content.     

Linear versus nonlinear determinations of equilibrium melting temperatures of poly(trimethylene terephthalate) and miscible blend with poly(ether imide) exhibiting multiple melting peaks

Multiple melting peaks in some semicrystalline polymers such as poly(trimethylene terephthalate) (PTT) have caused some difficulty in estimating accurately the equilibrium melting points. PTT forms a miscible blend with amorphous poly(ether imide) (PEI); for comparison purposes, a miscible system of a fixed composition (PTT/PEI of weight ratio = 9/1) was determined. PTT and its miscible blend both exhibited dual melting peaks (labeled as low and high peaks: T_m,L, T_m,H), and the first peaks (T_m,L), not the second peak (T_m,H), should be used for extrapolation. The equilibrium melting temperatures (T) of neat PTT and its blend PTT/PEI (9/1) were 245.2 and 242.4 °C, respectively, by the linear Hoffman–Weeks treatment using the corrected values of T_m,L (i.e., values obtained using a heating rate close to zero). Linear and nonlinear treatments led to a significant difference in estimated T, and the relative validity of these two methods is discussed. The nonlinear estimate yielded a higher value by about 27.3 °C for neat PTT and 23.1 °C for the PTT/PEI (9/1) blend, respectively (also the correction in T_m,L at the same condition mentioned previously). Results showed melting depression in miscible PTT/PEI (9/1). In addition, the T value of neat PTT was higher than that of PTT/PEI (9/1) owing to much thicker and more‐perfect crystals in neat PTT. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1571–1581, 2002     

Conformation of poly(L-glutamic acid) in aqueous solutions of linear amphiphiles with a cationic group at both ends

The conformations of poly(l-glutamic acid) [P(Glu)] in solutions of the bipolar amphiphile 1,20-icosanediylbis(alkylammonium chloride) [C20(RA)₂], where RA includes trimethylammonium (TMA), dimethylammonium (DMA), or methylammonium (MA), were investigated with measurements of the circular dichroism spectra at 10–35 °C. All C20(RA)₂ induced an α-helix of P(Glu) in the aqueous solutions. The residue molar ellipticity at 222 nm showed a similar dependence on the amphiphile concentration (C _s) below 0.5 of the ratio of 2C _s to the residue concentration (C _p) of P(Glu), but it separated into three directions at 2C _s/C _p>0.5. C20(MA)₂ induced an α-helix of P(Glu) at 2C _s/C _p<0.5 followed by a helix aggregate at 2C _s/C _p>0.5. C20(DMA)₂ and C20(TMA)₂ also induced an α-helix, but a helix aggregate. C20(TMA)₂ indicated a strong temperature dependence and did not induce a complete α-helix at 35 °C. Received: 20 June 2001 Accepted: 6 September 2001     

Effect of poly(vinyl acetate) (PVAc) on thermal behavior and mechanical properties of poly(3-hydroxybutyrate)/poly(propylene carbonate) (PHB/PPC) blends

To assess the compatibility of blends of synthetic poly(propylene carbonate) (PPC), with a natural bacterial poly(3-hydroxybutyrate) (PHB), a simple casting procedure of blend was used. poly(3-hydroxybutyrate)/poly(propylene carbonate) blends are found to be incompatible according to DSC and DMA analysis. In order to improve the compatibility and mechanical properties of PHB/PPC blends, poly(vinyl acetate) (PVAc) was added as a compatibilizer. The effects of PVAc on the thermal behavior, morphology, and mechanical properties of 70PHB/30PPC blend were investigated. The results show that the melting point and the crystallization temperature of PHB in blends decrease with the increase of PVAc content in blends, the loss factor changes from two separate peaks of 70PHB/30PPC blend to one peak of 70PHB/30PPC/12PVAc blend. It is also found that adding PVAc into 70PHB/30PPC blend can decrease the size of dispersed phase from morphology analysis. The result of tensile properties shows that PVAc can increase the tensile strength and Young’s modulus of 70PHB/30PPC blend, and both the elongation at break and the tensile toughness increase significantly with PVAc added into 70PHB/30PPC.     

Effect of poly(butylene succinate) crystals on spherulitic growth of poly(ethylene oxide) in binary blends of the two substances

The effects of the lamellar growth direction, extinction rings, and spherulitic boundaries of poly(butylene succinate) (PBSU) on the spherulitic growth of poly(ethylene oxide) (PEO) were investigated in miscible blends of the two crystalline polymers. In the crystallization process from a homogeneous melt, PBSU first developed volume‐filling spherulites, and then PEO spherulites nucleated and grew inside the PBSU spherulites. The lamellar growth direction of PEO was identical with that of PBSU even when the PBSU content was about 5 wt %. PEO, which intrinsically does not exhibit banded spherulites, showed apparent extinction rings inside the banded spherulites of PBSU. The growth rate of a PEO spherulite, G_PEO, was influenced not only by the blend composition and the crystallization temperature of PEO, but also by the growth direction with respect to PBSU lamellae, the boundaries of PBSU spherulites, and the crystallization temperature of PBSU, T_PBSU. The value of G_PEO first increased with decreasing T_PBSU when a PEO spherulite grew inside a single PBSU spherulite. Then, G_PEO decreased when T_PBSU was further decreased and a PEO spherulite grew through many tiny PBSU spherulites. This behavior was discussed based on the aforementioned factors affecting G_PEO. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 539–547, 2009     

Three types of banded structures in highly birefringent poly(trimethylene terephthalate) spherulites

Poly(trimethylene terephthalate) (PTT), a highly birefringent aromatic polyester, has been utilized to understand the mechanisms of crystal assembly into diversified types of banded spherulites. PTT exhibits three main types of banded spherulites (i.e., concentric, single‐spiral, and double‐spiral) co‐existing in sample films melt‐crystallized at 165 °C, regardless of sample thickness. The three types differ in their banding structures, interference color distributions, and nuclei geometries (S‐shape, Z‐shape, or dot‐shape). Core diameter, band spacing ratio, and height difference (Δz) around the core are the three key parameters of different banding patterns in PTT spherulites. Formation mechanism for three types of banded spherulites has been interpreted, and found to be highly correlated with the initial geometry shapes of their nuclei. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1207–1216     

Relationships between ringed spherulitic morphology and miscibility in blends of poly(ɛ-caprolactone) with poly(benzyl methacrylate) versus poly(phenyl methacrylate)

 Ringed spherulites are an interesting phenomenon that is observed only in very few miscible systems. For the first time, the relationship between the state of chain intermixing and the ring-band pattern was demonstrated. Two previously demonstrated miscible blend systems, poly(ɛ-caprolactone) (PCL) with poly(benzyl methacrylate) (PBzMA) and PCL with poly(phenyl methacrylate) (PPhMA), were studied in order to understand the mechanism of ring-band formation in the spherulites and the relationships between the ring-band pattern and the state of miscibility. In both miscible PCL/PBzMA and PCL/PPhMA systems, extinction rings were observed within the PCL spherulites. In the PCL/PBzMA blend, the extinction rings are not as distinct (owing to distortion) as those in the PCL/PPhMA blend system. Analysis was performed and discussions were made to reveal relationships between miscibility, interaction strength, and the pattern of the ring bands in the PCL spherulites in polymeric mixtures. Received: 5 January 2000/Accepted: 14 March 2000     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. I. Spherulitic morphology and growth by polarized microscopy

The development of the poly(3‐hydroxybutyrate) (PHB) morphology in the presence of already existent poly(vinylidene fluoride) (PVDF) spherulites was studied by two‐stage solidification with two separate crystallization temperatures. PVDF formed irregular dendrites at lower temperatures and regular, banded spherulites at elevated temperatures. The transition temperature of the spherulitic morphology from dendrites to regular, banded spherulites increased with increasing PVDF content. A remarkable amount of PHB was included in the PVDF dendrites, whereas PHB was rejected into the remaining melt from the banded spherulites. When PVDF crystallized as banded spherulites, PHB could consequently crystallize only around them, if at all. In contrast, PHB crystallized with a common growth front, starting from a defined site in the interfibrillar regions of volume‐filling PVDF dendrites. It formed by itself dendritic spherulites that included a large number of PVDF spherulites. For blends with a PHB content of more than 80 wt %, for which the PVDF dendrites were not volume‐filling, PHB first formed regular spherulites. Their growth started from outside the PVDF dendrites but could later interpenetrate them, and this made their own morphology dendritic. These PHB spherulites melted stepwise because the lamellae inside the PVDF dendrites melted at a lower temperature than those from outside. This reflected the regularity of the two fractions of the lamellae because that of those inside the dendrites of PVDF was controlled by the intraspherulitic order of PVDF, whereas that from outside was only controlled by the temperature and the melt composition. The described morphologies developed without mutual nucleating efficiency of the components. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 873–882, 2003     

Morphology and crystallization behavior of poly(vinylidene fluoride)/poly(methyl methacrylate)/methyl salicylate,and benzophenone systems via thermally induced phase separation

Poly(vinylidene fluoride) (PVDF) blend microporous membranes were prepared by PVDF/poly(methyl methacrylate) blend (with mass ratio = 70/30) via thermally induced phase separation. Benzophenone (BP) and methyl salicylate (MS) were used as diluents. The phase diagram calculations were carried out in terms of a pseudobinary system, considering the PVDF blend to be one component. The crytallization behaviors of PVDF in the dilutions were detected by differential scanning calorimetry measurement. In these two systems, the melting and crystallization temperatures leveled off in the low polymer concentration (<40 wt %), but shifted to a higher temperature when the polymer concentration >40 wt %. The calculated crystallinity of PVDF for samples with low polymer concentrations was greater than those with high polymer concentrations, because of the limited mobility of polymer chains at a high polymer concentration. The membrane structure as determined by scanning electron microscopy depended on the phase separation mechanism. The quenched samples mainly illustrated the occurrence of crystallization on the same time scale as the liquid–liquid phase separated, resulting in the obvious spherulitic structure with small pores in the spherulites. As the polymer concentration increased, the size of the spherulites and pores within the spherulite was decreased. The evaluated porosity for BP diluted system was higher than that for MS diluted system, and decreased with the increased polymer concentration. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 248–260, 2009     

Effect of MMT,SiO2, CaCO3, and PTFE nanoparticles on the morphology and crystallization of poly(vinylidene fluoride)

The crystallization and melting behaviors of poly (vinylidene fluoride) (PVDF) with small amount of nanoparticles (1 wt %), such as montmorillonite (MMT), SiO₂, CaCO₃, or polytetrafluoroethylene (PTFE), directly prepared by melt‐mixing method were investigated by scanning electron microscopy (SEM), polarizing optical microscopy, Fourier transform infrared spectroscopy, wide angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC). The nanoparticle structure and the interactions between PVDF molecule and nanoparticle surface predominated the crystallization behavior and morphology of the PVDF. Small amount addition of these four types of nanoparticles would not affect the original crystalline phase obtained in the neat PVDF sample (α phase), but accelerated the crystallization rate because of the nucleation effect. In these four blend systems, MMT or PTFE nanoparticles could be well applied for PVDF nanocomposite preparation because of stronger interactions between particle surface and PVDF molecules. The nucleation enhancement and the growth rate of the spherulites were decreased in the order SiO₂ > CaCO₃ > PTFE > MMT. The melting and recrystallization of PVDF was found in MMT addition sample, because of the special ways of ordering of the PVDF chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010