Method validation for the analysis of 169 pesticides in soya grain, without clean up, by liquid chromatography-tandem mass spectrometry using positive and negative electrospray ionization

Part of a comprehensive study on the comparison of different extraction methods, GC-MS(/MS) and LC-MS/MS detection methods and modes, for the analysis of soya samples is described in this paper. The validation of an acetone-based extraction method for analysis of 169 pesticides in soya, using LC-MS/MS positive and negative electrospray ionisation (ESI) mode, is reported. Samples (5 g) were soaked with 10 g water and subsequently extracted with 100 mL of a mixture of acetone, dichloromethane and light petroleum (1:1:1), in the presence of 15 g anhydrous sodium sulphate. After centrifugation, aliquots of the extract were evaporated and reconstituted in 1.0 mL of methanol, before direct injection of the final extract (corresponding with 0.05 g soya mL(-1)) into the LC-MS/MS system. Linearity, r(2) of calibration curves, instrument limit of detection/quantitation (LOD/LOQ) and matrix effect were evaluated, based on seven concentrations measured in 6-fold. Good linearity (at least r(2)> or =0.99) of the calibration curves was obtained over the range from 0.1 or 0.25 to 10.0 ng mL(-1), corresponding with pesticide concentrations in soya bean extract of 2 or 5-200 microg kg(-1). Instrument LOD values generally were 0.1 or 0.25 ng mL(-1). Matrix effects were negligible for approximately 90% of the pesticides. The accuracy, precision and method LOQ were determined via recovery experiments, spiking soya at 10, 50, 100 microg kg(-1), six replicates per level. In both ESI modes, method LOQ values were mostly 10 or 50 microg kg(-1) and more than 70% of pesticides analysed by each mode met the acceptability criteria of recovery (70-120%) and RSD (< or =20%), at one or more of the three levels studied. A fast, easy and efficient method with acceptable performance was achieved for a difficult matrix as soya, without cleanup.     

Rapid analysis of pyrethroid insecticides in aquaculture seawater samples via membrane-assisted solvent extraction coupled with gas chromatography-electron capture detection

A simple, efficient, and environmentally friendly membrane-assisted solvent extraction (MASE) method for the extraction and preconcentration of six pyrethroid insecticides from aquaculture seawater samples followed by gas chromatography-electron capture detection (GC-ECD) was successfully proposed. The operating conditions for MASE, such as the extraction solvent, solvent volume, NaCl concentration, stirring rate, extraction time, and temperature, were optimized. Compared to conventional Florisil-solid phase extraction (SPE), higher extraction recoveries (85.9% to 105.9%) of three spiked levels of the six pyrethroid pesticides in aquaculture seawater were obtained using MASE, and the RSD values were lower than 7.9%. The limits of detection (LOD, signal-to-noise ratio (S/N)=3) and quantification (LOQ, S/N = 10) were in the range of 0.037-0.166 and 0.12-0.55 μg L(-1), respectively. The results demonstrate the excellent applicability of the MASE method in analyzing the six pyrethroid pesticides in aqueous samples. The proposed method exhibited a high potential for routine monitoring analysis of pyrethroid insecticides in seawater samples.     

Determination of alachlor, metolachlor, and their acidic metabolites in soils by microwave-assisted extraction (MAE) combined with solid phase extraction (SPE) coupled with GC-MS and HPLC-UV analysis

A well-validated analytical method based on microwave-assisted extraction (MAE) and SPE is presented for the combined analysis of alachlor, alachlor-oxanilic acid (OXA), alachlor-ethanesulfonic acid (ESA), metolachlor, metolachlor-OXA, metolachlor-ESA residues in soils. Extraction of solutes by soil sample was carried out by MAE for 20 min at 100 degrees C in the presence of 50 mL solution (methanol/water 50:50), the extract was subsequently passed through C18 cartidges and fractionated into two fractions, the first with parent compounds (PCs) analyzed with GC-MS and the second one containing the metabolites analyzed with HPLC. For the SPE step, various types of sorbents (Environmental C18, tC18, Supelclean ENVI-carb, and LiChrolut EN) have been used, and their respective advantages and disadvantages are discussed. After the method optimization, average recovery values of all solutes were > 71% in the 50-500 microg/kg fortification range with RSD <10%. The LOQ and LOD were 10-50 and 5-10 microg/kg, respectively. The method was validated with two types of soils (1 and 2.4% organic matter) and in fresh (12 h aging), intermediate (1 wk aging), and aged (1 month aging) spiked samples. Moreover, residue levels determined after field application of alachlor or metolachlor were higher when soils were processed using this method than with a comparison method based on an overnight flask shaking (FS) of soil suspension.     

固相萃取-液相色谱-串联质谱法测定海水中软骨藻酸

软骨藻酸(domoic acid, DA)是一种由海洋硅藻产生的生物毒素,具有强烈的神经毒性,近海水环境中的DA严重威胁海洋渔业生物和人类健康,因此对近海水环境中的DA进行有效监测至关重要。该文基于固相萃取-液相色谱-串联质谱联用技术(SPE-LC-MS/MS),建立了适用于海水中痕量、超痕量DA的检测方法。针对近海水生环境中DA浓度相对较高的情况下,采用在线SPE-LC-MS/MS检测模式,可减少前处理过程,提高样品的分析效率。离线SPE结合在线SPE-LC-MS/MS可实现大洋和极地海水中含量更低的DA的检测。通过对在线固相萃取条件和液相色谱、质谱条件的优化,海水样品经过滤和酸化简单处理后直接进样0.6 mL进行在线SPE-LC-MS/MS检测,DA在10.0~500.0 ng/L范围内线性关系良好(线性相关系数R²=0.9992),检出限(LOD)和定量限(LOQ)分别为4.0和10.0 ng/L,并且具有较好的方法回收率(≥81.0%)和精密度(RSD≤4.2%),表明方法可用于近海海水中痕量DA的检测。通过对离线固相萃取柱的选择和酸化条件的优化,80.0 mL海水样品经离线HLB固相萃取柱富集后,进行在线SPE-LC-MS/MS检测,DA在0.3~50.0 ng/L范围内线性关系良好(R²=0.9990),回收率(≥69.2%)和精密度(RSD≤4.4%)较好,LOD和LOQ分别为0.1和0.3 ng/L,说明方法的灵敏度较直接进样法大幅提升,实现了海水中超痕量DA的准确测定。这两种检测方法操作简单,样品用量小,灵敏度高,可满足近海养殖区及远岸海水中DA监测的要求。     

Rapid analysis of 2,4-D in soil samples by modified Soxhlet apparatus using HPLC with UV detection

The 2,4-dichlorophenoxy acetic acid (2,4-D) is used as a systemic herbicide to control broadleaf weeds in wheat, corn, range land/pasture land, sorghum, and barley. In this study, a fast and efficient method is developed by selection of modified extraction apparatus and high-performance liquid chromatography (HPLC)-UV conditions for the determination of 2,4-D in soil samples. The method is applied to the study of soil samples collected from the agricultural field. The herbicide is extracted from soil samples by acetonitrile in a modified Soxhlet apparatus. The advantages of the apparatus are that it uses small volume of organic solvent, reduced time of extraction, and better recovery of the analyte. The extract is filtered using a very fine microfiber paper. The total extract is concentrated in a rotatory evaporator, dried under ultrahigh pure N2, and finally reconstituted in 1 mL of acetonitrile. HPLC-UV at 228 nm is used for analysis. The herbicide is identified and quantitated using the HPLC system. The method is validated by the analysis of spiked soil samples. Recoveries obtained varied from 85% to 100% for spiked soil samples. The limit of quantitation (LOQ) and the limit of detection (LOD) are 0.010 and 0.005 parts per million (ppm), respectively, for spiked soil samples. The LOQ and LOD are 0.006 and 0.003 ppm for unspiked soil samples. The measured concentrations of 2,4-D in spiked soil samples are between 0.010 and 0.020 ppm with an average of 0.016 +/- 0.003 ppm. For unspiked soil samples it is between 0.006 ppm and 0.012 ppm with an average of 0.009 +/- 0.002 ppm. The measured concentrations of 2,4-D in soil samples are generally low and do not exceed the regulatory agencies guidelines.     

Fast gas chromatography/mass spectrometric assay for the validated quantitative determination of methadone and the primary metabolite EDDP in whole blood

A toxicological analysis was developed and validated for simultaneous screening and quantification of methadone (METH) and its primary metabolite 2-ethylidene-1,5-dimethyl-3,3-diphenylpyrrolidine (EDDP). The method employs microscale liquid-liquid extraction (microLLE) and direct injection of a separated aliquot of the organic layer into a gas chromatography/mass spectrometric (GC/MS) system without any other pre-treatment stages. A fast GC/MS runtime (total 5.8 min; METH, Rt = 3.55 min; EDDP, Rt = 3.40 min) combined with rapid sample preparation allowed cost-efficient and routinely applicable performance with a low amount of manual work. The validated parameters included: linearity (25-1000 ng mL(-1) both; R(METH)2 = 0.998 and R(EDDP)2 = 0.997), accuracy (Bias(METH): from -0.05 to 11.3%, Bias(EDDP): from 1.11 to 4.37%); intra and inter-assay precision (RSD(METH): from 2.4 to 3.9%, from 4.89 to 10.3%; RSD(EDDP): from 4.50 to 6.20%, from 4.57 to 15.2%), extraction efficiency (METH = 95.5%; EDDP = 90.6%), LOQ(Meth,EDDP) = 25 ng mL(-1). Samples were stable for at least 25 h and no selectivity problems or baseline interference were observed. The method should be applicable for identifying and quantitative confirmation of possible misuse and/or illegal use of METH in toxicological cases.     

Simultaneous determination of six toxic alkaloids in human plasma and urine using capillary zone electrophoresis coupled to time‐of‐flight mass spectrometry

A novel capillary zone electrophoresis separation coupled to electro spray ionization time‐of‐flight mass spectrometry method was developed for the simultaneous analysis of six toxic alkaloids: brucine, strychnine, atropine sulfate, anisodamine hydrobromide, scopolamine hydrobromide and anisodine hydrobromide in human plasma and urine. To obtain optimal sensitivity, a solid‐phase extraction method using Oasis MCX cartridges (1 mL, 30 mg; Waters, USA) for the pretreatment of samples was used. All compounds were separated by capillary zone electrophoresis at 25 kV within 12 min in an uncoated fused‐silica capillary of 75 μm id × 100 cm and were detected by time‐of‐flight mass spectrometry. This method was validated with regard to precision, accuracy, sensitivity, linear range, limit of detection (LOD), and limit of quantification (LOQ). In the plasma and urine samples, the linear calibration curves were obtained over the range of 0.50–100 ng/mL. The LOD and LOQ were 0.2–0.5 ng/mL and 0.5–1.0 ng/mL, respectively. The intra‐ and interday precision was better than 12% and 13%, respectively. Electrophoretic peaks could be identified by mass analysis.     

Stir bar sorptive extraction and high-performance liquid chromatography-fluorescence detection for the determination of polycyclic aromatic hydrocarbons in Mate teas

A simple procedure based on stir bar sorptive extraction (SBSE) and high-performance liquid chromatography-fluorescence detection (HPLC-FLD) is presented for the determination of 15 polycyclic aromatic hydrocarbons (PAHs) in herbal tea prepared with Mate leaves (Ilex paraguariensis St. Hil.). The influence of methanol and salt addition to the samples, the extraction time, the desorption time and the number of desorption steps, as well as the matrix effect, were investigated. Once the SBSE method was optimised (10 mL of Mate tea, 2h extraction at room temperature followed by 15 min desorption in 160 microL of an acetonitrile (ACN)-water mixture), analytical parameters such as repeatability (< or = 10.1%), linearity (r2 > or = 0.996), limit of detection (LOD, 0.1-8.9 ng L(-1) ), limit of quantitation (LOQ, 0.3-29.7 ng L(-1) and absolute recovery (24.2-87.0%) were determined. For calibration purposes, a reference sample was firstly obtained by removing the analytes originally present in the lowest contaminated Mate tea studied (via SBSE procedure) and then spiked at 1-1200 ng L(-1)range. The proposed methodology proved to be very convenient and effective, and was successfully applied to the analysis of 11 Mate tea samples commercialised in Brazil. The results of the commercial Mate tea samples found by the SBSE approach were compared with those obtained by liquid-liquid extraction (LLE), showing good agreement.     

Determination of nitrate esters in water samples Comparison of efficiency of solid-phase extraction and solid-phase microextraction

This paper deals with comparison of efficiency of extraction techniques (solid-phase extraction, SPE and solid-phase microextraction, SPME) used for extraction of nitrate esters (ethyleneglycoldinitrate, EGDN and nitroglycerin, NG), representing the first step of the method of quantitative determination of trace concentrations of nitrate esters in water samples. EGDN and NG are subsequently determined by means of high-performance liquid chromatography with ultraviolet detection (HPLC-UV). Optimization of SPE and SPME conditions was carried out using model water samples. Seven SPE cartridges were tested and the conditions were optimized (type of sorbent, type and volume of solvent to be used as eluent). For both nitrate esters the limit of detection (LOD) and the limit of quantification (LOQ) obtained using SPE/HPLC-UV were 0.23 microg mL(-1) and 0.70 microg mL(-1), respectively. Optimization of SPME conditions: type of SPME fibre (four fibres were tested), type and time of sorption/desorption, temperature of sorption. PDMS/DVB (polydimethylsiloxane/divinylbenzene) fibre coating proved to be suitable for extraction of EGDN and NG. For this fibre the LOD and the LOQ for both nitrate esters were 0.16 microg mL(-1) and 0.50 microg mL(-1), respectively. Optimized methods SPE/HPLC-UV and SPME/HPLC-UV were then used for quantitative determination of nitrate esters content in real water samples from the production of EGDN and NG.     

Determination of ng/mL levetiracetam using ultra-high-performance liquid chromatography-photodiode absorbance

This paper demonstrates the analysis of levetiracetam, a new chiral antiepileptic drug, at ng/mL levels using an ultra-high-performance liquid chromatography (UHPLC)-photodiode absorbance (PDA) method. Three different sample preparation methods, liquid-liquid extraction with Extrelut, solid phase extraction (SPE) with Oasis HLB and Oasis MAX SPE cartridges, and protein precipitation with organic solvents were carried out. The last preparatory method is the simplest and provides the best recoveries: between 97.1% and 100.4% with RSD value below 5%. The column for separation is BEH C18 column (1.7 μm particle size and 100 × 2.1 mm i.d.) and acetonitrile-phosphate buffer (pH = 6.6; 0.01 M) (10/90 v/v) is the mobile phase. The results obtained are compared to analysis conducted by the HPLC method. The UHPLC method was validated in the range of 2-100 μg/mL levetiracetam concentration (R(2) = 0.9997). LOD and LOQ are 10 ng/mL and 33 ng/mL, respectively. The developed UHPLC method was applied to plasma samples of patient with epilepsy.     

Preparation of cyano-functionalized multiwalled carbon nanotubes as solid-phase extraction sorbent for preconcentration of phenolic compounds in environmental water

In the present work, we showed a novel method to synthesize cyano-functionalized multiwalled carbon nanotubes (MWCNTs-CN) and utilize it as a solid-phase extraction sorbent for preconcentration of phenolic compounds in environmental water samples. MWCNTs-CN was synthesized through surface functionalization of multiwalled carbon nanotubes (MWCNTs). The functional groups on the surface of modified MWCNTs were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis and scanning electron microscopy. The analytical procedure was based on a conventional solid-phase extraction step for which 100 mg of MWCNTs-CN were packed in a 3 mL polypropylene cartridge. Analytes were thus isolated and preconcentrated from the pretreated samples and subsequently detected on high-performance liquid chromatography-ultraviolet detection. The results showed the proposed method exhibited good sensitivity and precision for the extraction and elution of analytes. The limit of detections (S/N = 3) of the method were 0.45, 0.09, 0.08, and 3.00 ng mL(-1) for p-chlorophenol, 1-naphthol, 2-naphthol, and 2,4-dichlorophenol, respectively. The mean relative recoveries (n = 3) were between 80.28 and 103.13%, and the repeatability (RSD ≤ 5.10%) and reproducibility (RSD ≤ 7.68%) were accepted. This developed method was applied to determine phenolic compounds in environmental water samples. There is a positive result only for 2-naphthol with concentration of 0.38 ng mL(-1) in seawater sample.     

Determination of streptomycin residue in cucumber and Chinese cabbage by high-performance liquid chromatography with postcolumn derivatization and fluorometric detection

A sensitive and accurate method was developed for the determination of streptomycin using HPLC followed by postcolumn derivatization and fluorometric detection. The analyte was extracted, using aqueous solution from cucumber and Chinese cabbage, by a two-step SPE procedure. The extraction, cleanup, and chromatography conditions were optimized, and the performance of the analysis method was evaluated. The conditions of chromatography were as follows: the separation was performed on a C18 column; the isocratic mobile phase consisted of acetonitrile and a mixed solution containing 10 mM sodium 1,2-naphthoquinone-4-sulfonate and 0.4 mM sodium 1-heptanesulfonate (25+75, v/v); and the flow rate was 1 mL/min. The fluorescence detector was set at an excitation wavelength of 263 nm and an emission wavelength of 435 nm. The calibration curve was linear over the range of 50-2000 ng/mL, with a correlation coefficient of 0.9995. The LOD and LOQ were 10 and 30 ng/g, respectively, in both cucumber and Chinese cabbage. The method was validated for selectivity, linearity, precision, and accuracy. The intraday and interday precision and accuracy were within 10%. The mean recoveries from spiked samples were more than 75%, with RSD lower than 10%.     

Validation of a multiresidue method for the determination of pesticides in honeybees by gas chromatography

The validation of a multiresidue method for the determination of organochlorine, organophosphorus, pyrethroid and dicarboximide pesticides in honeybees is described. The method involves the extraction of 25 pesticides using acetonitrile, liquid partitioning with n-hexane and a clean-up performed on a silica gel cartridge (1 g, 12 mL). Capillary gas chromatography with electron-capture and nitrogen–phosphorus detectors was used for analytes determination. Limit of quantification (LOQ), recovery and relative standard deviation (RSD) for each analyte were determined. The recovery data were obtained by spiking honeybee samples free of pesticides at three levels (LOQ, 4LOQ and 8LOQ) with organochlorine, organophosphorus, pyrethroid and dicarboximide pesticides. The recoveries were in the range between 90.0% and 101.5% for LOQ, between 90.3% and 104.8% for 4LOQ and between 88.1% and 101.6% for 8LOQ with RSD less than 20% for the three levels tested. The lowest LOQ value was 1 ng bee^?1 (corresponding to 10 ng g^?1) and the highest LOQ value was 10 ng bee^?1 (corresponding to 100 ng g^?1). These LOQ values are lower than the lethal doses LD₅₀ (acute contact toxicity and acute oral toxicity) of each pesticide for bees.     

Simultaneous Determination of Hydrochlorothiazide and Reserpine in Human Urine by LC with a Simple Pre-Treatment

A simple, selective and sensitive reversed-phase high performance liquid chromatography method for simultaneous analysis of hydrochlorothiazide and reserpine in human urine was developed and subjected to primary pharmacokinetic study. After a simple protein precipitation using methanol and extraction with ethyl acetate, the analytes were separated on an Elite C(18) column at a flow rate of 0.8 mL min(-1). The mobile phase was composed of acetonitrile (A) and 0.2% ammonium chloride solution (B) for a gradient elution starting at A:B at 30:70, v/v for 0~6 min, linearly raising the percent of A from 30% to 50% (6~9 min) and ending at 50:50, v/v (9~25 min). The standard curves were linear over the range of 0.05-20 μg mL(-1) for hydrochlorothiazide and 0.02-5.0 μg mL(-1) for reserpine, respectively (r > 0.999). The limit of detection (LOD) and the limit of quantification (LOQ) were 5.5 ng mL(-1) and 18.2 ng mL(-1) for hydrochlorothiazide, and 7.1 ng mL(-1) and 23.6 ng mL(-1) for reserpine, respectively. The recoveries for both analytes were above 89.0±1.35%. The intra-day and inter-day precision for hydrochlorothiazide were less than 1.91% and 1.38%, and those for reserpine were below 1.61% and 2.64%, respectively. The method indicated good performance in terms of specificity, linearity, detection and quantification limits, precision and accuracy, and it was employed successfully for the simultaneous determination of hydrochlorothiazide and reserpine in human urine samples.     

Simultaneous determination of anthracyclines and taxanes in human serum using online sample extraction coupled to high performance liquid chromatography with UV detection

An online SPE‐LC method that can determine both anthracyclines and taxanes simultaneously in human serum samples is reported. The entire method of extraction, separation and UV detection was achieved online by column switching between an SPE column (Biotrap 500 (20×4 mm)) and an analytical column (Zorbax XDB C18, 150×4.6 mm, 5 μm) with a 23 min total cycle time. The method is linear (r²>0.998) over the range of 0.5–25 μg/mL. The analytes of interest are retained on the SPE column with good recovery (84–117%), while proteins and other serum components elute to waste. This online clean‐up is much faster (150 s) and less manual than traditional off‐line extraction methods. Using 0.1 mL spiked serum samples, the LOQ was 0.5 μg/mL. Intra‐ and inter‐day precision were acceptable (≤15% RSD) at and above the LOQ. The method was applied to the analysis of serum samples from patients undergoing chemotherapy with these agents.     

Rapid determination of ethylene oxide with fiber-packed sample preparation needle

Fiber-packed sample preparation device was applied to the simultaneous derivatization/preconcentration of ethylene oxide (EO) in air samples. The polymer-coated filaments were packed longitudinally into the needle, and hydrogen bromide (HBr) was loaded onto the filaments in the preconditioning process. Simultaneous derivatization with HBr in the needle was made during the sampling process of the gaseous EO, and the corresponding derivatized analyte, 2-bromoethanol, was desorbed by passing a small amount of methanol through the extraction needle in the heated gas chromatograph (GC) injector. The basic extraction/desorption parameters for EO have been evaluated. The limit of detection (LOD), limit of quantification (LOQ) and the relative standard deviation (RSD) of run-to-run repeatability were 1.8 ng/L, 5.4 ng/L and less than 4%, respectively, with an extraction time of about 10 min. Satisfactory storage performance for three days at room temperature was also confirmed.     

Determination of Ochratoxin A in wine at sub ng/mL levels by solid-phase microextraction coupled to liquid chromatography with fluorescence detection

Solid-phase microextraction (SPME), using a polydimethylsiloxane/divinylbenzene (PDMS/DVB) fiber, interfaced with liquid chromatography-fluorescence detection (LC-FD) has been applied to the determination of Ochratoxin A (OTA) in wine samples. Compared to the most widely adopted extraction/clean-up procedure based on immunoaffinity columns (IAC), the solventless extraction is simpler and cost-effective, requiring the simple immersion of the fiber in diluted wine samples. Furthermore, a fast LC separation is achieved under isocratic conditions. The linear range investigated in wine was 0.25-8 ng/mL; at fortification levels of 0.5 and 2 ng/mL, within-day intra-laboratory precision (repeatability) values, expressed as RSD%, were 5.9 and 5.1, respectively, whereas between days (n = 4) precision was 8.5 and 7.1%, respectively. The limit of detection (LOD) at a signal-to-noise (S/N) ratio of 3 was 0.07 ng/mL; the limit of quantification (LOQ) calculated at S/N = 10 was 0.22 ng/mL, well below the European regulatory level of 2 ng/mL. The potential of the method has been demonstrated by the analysis of a number of different wine samples.     

Determination of hexanal as an oxidative marker in vegetable oils using an automated dynamic headspace sampler coupled to a gas chromatograph/mass spectrometer

An automated dynamic headspace sampler coupled to a gas chromatograph/mass spectrometer was evaluated as an oxidative marker to determine hexanal content in vegetable oils. For the effective analysis, a cooled injection system (CIS) was used to focus and to introduce the hexanal desorbed from the Tenax TA. The temperature of the CIS was maintained at -60 °C for 12 min before desorbing the hexanal. Hexanal was separated on a capillary column (DB-5, 0.25 mm × 60 m, 0.25 μm in film thickness) from 50 to 230 °C, followed by mass spectrometer-selected ion monitoring analysis at m/z 56. The instrumental response to hexanal was highly linear from 10 ng mL(-1) to 1 μg mL(-1) (r(2) = 0.9999). The relative standard deviation (RSD) of intra- and inter-day repeatability was acceptable, with values of less than 3.88 and 4.25%, respectively. The LOD and LOQ of hexanal were determined by gas chromatograph/mass spectrometer-selected ion monitoring to be 3.3 and 9.8 ng mL(-1), respectively. The acid value, peroxide value and fatty acid composition revealed a good correlation with the hexanal concentration.     

Validation assay for total flavonoids, as rutin equivalents, from Trichilia catigua Adr. Juss (Meliaceae) and Ptychopetalum olacoides Bentham (Olacaceae) commercial extract

An ultraviolet spectrophotometric method was validated for total flavonoid quantitation, as rutin equivalents, present in the Trichilia catigua Adr. Juss (Meliaceae) and Ptychopetalum olacoides Bentham (Olacaceae) commercial extract. Parameters as linearity, interval (range), specificity, estimated limit of detection (LOD, microg/mL), estimated limit of quantitation (LOQ, microg/mL), recovery (R, %), precision or relative standard deviation (RSD, %), and accuracy (E, %) were established. The analytical method was validated according to the experimental results: correlation coefficient (r = 0.9997); interval (RSD = 0.15-0.47%; E = 98.98-101.24%); specificity to total flavonoids quantitation, as rutin equivalents, at wavelength 361.0 nm; LOD = 0.09 microg/mL and LOQ = 0.27 microg/mL; R = 99.36-102.14%; adequate intra- and interrun precision (0.30-0.49% and 0.31-0.81%), and intra- and interrun accuracy (100.60-102.38% and 98.58-100.38%).     

Determination of vitexin and isovitexin in pigeonpea using ultrasonic extraction followed by LC-MS

A method based on ultrasonic extraction (USE) followed by LC-MS is presented for the determination of vitexin and isovitexin in pigeonpea extracts in this study. The influential parameters of the USE procedure were optimized, and the optimal conditions were as follows: extraction solvent, 60% ethanol solution; liquid/solid ratio 10:1 (mL/g), extraction power, 250 W; temperature, 40-50 degrees C; and three extraction cycles, each cycle 15 min. Validation of the USE method was performed in terms of repeatability and reproducibility. RSDs for extraction yields were lower than 5.85 and 8.09%, respectively. The LOD and LOQ of chromatographic determination were 0.96 and 3.2 ng/mL for vitexin and 0.84 and 2.8 ng/mL for isovitexin. The method was also successfully applied for the determination of vitexin and isovitexin in stems, leaves, and root extracts of pigeonpea. From all these results, we may conclude that the developed method is appropriate for the quality control of pigeonpea and other plant extract products developed from pigeonpea.