Numerical simulation of Mach reflection of cellular detonations

The Mach reflection of cellular detonation waves on a wedge is investigated numerically in an attempt to elucidate the effect of cellular instabilities on Mach reflection, the dependence of self-similarity on the thickness of a detonation wave, and the initial development of the Mach stem near the wedge apex. A two-step chain-branching reaction model is used to give a thermally neutral induction zone followed by a chemical reaction zone for the detonation wave. A sufficiently large distance of travel of the Mach stem is computed to observe the asymptotic behavior in the far field. Depending on the scale at which the Mach reflection process occurs, it is found that the Mach reflection of a cellular detonation behaves essentially in the same way as a planar ZND detonation wave. The cellular instabilities, however, cause the triple-point trajectory to fluctuate. The fluctuations are due to interactions of the triple point of the Mach stem with the transverse waves of cellular instabilities. In the vicinity of the wedge apex, the Mach reflection is found to be self-similar and corresponds to that of a shock wave of the same strength, since the Mach stem is highly overdriven initially. In the far field, the triple-point trajectory approaches a straight line, indicating that the Mach reflection becomes self-similar asymptotically. The distance of the approach to self-similarity is found to decrease rapidly with decreasing thickness of the detonation front.     

A numerical simulation of reflection processes of a detonation wave on a wedge

Abstract. A two dimensional numerical simulation has been performed to study reflection processes of detonation waves on a wedge. The numerical scheme adopted is the flux corrected transport scheme and a two-step chemical reaction is assumed for a stoichiometric oxyhydrogen mixture diluted with argon. Transverse wave structures of the detonation are produced by artificial disturbances situated in front of a one-dimensional Chapman-Jouguet detonation wave. Numerical grids are generated by solving a Laplace equation. Results show that in the case where Mach reflection occurs, the cells in the Mach stem are smaller than those in the incident wave and are distorted in shape. There is also an initiating stage during which the cells in the Mach stem are created. The critical angle beyond which Mach reflection cannot occur is discussed. Received 15 October 1999 / Accepted 27 March 2000     

On the influence of low initial pressure and detonation stochastic nature on Mach reflection of gaseous detonation waves

The two-dimensional, time-dependent and reactive Navier–Stokes equations were solved to obtain an insight into Mach reflection of gaseous detonation in a stoichiometric hydrogen-oxygen mixture diluted by 25 % argon. This mixture generates a mode-7 detonation wave under an initial pressure of 8.00 kPa. Chemical kinetics was simulated by an eight-species, forty-eight-reaction mechanism. It was found that a Mach reflection mode always occurs for a planar detonation wave or planar air shock wave sweeping over wedges with apex angles ranging from \(5^\circ \) to \(50^\circ \) . However, for cellular detonation waves, regular reflection always occurs first, which then transforms into Mach reflection. This phenomenon is more evident for detonations ignited under low initial pressure. Low initial pressure may lead to a curved wave front, that determines the reflection mode. The stochastic nature of boundary shape and transition distance, during deflagration-to-detonation transition, leads to relative disorder of detonation cell location and cell shape. Consequently, when a detonation wave hits the wedge apex, there appears a stochastic variation of triple point origin and variation of the angle between the triple point trajectory and the wedge surface. As the wedge apex angle increases, the distance between the triple point trajectory origin and the wedge apex increases, and the angle between the triple point trajectory and the wedge surface decreases exponentially.     

气相爆轰波在障碍物上Mach反射的实验验证

本文公布了气相爆轰波沿收缩管道传播时发生Mach反射的实验证据。在爆轰波通过的管道中安装不同楔角的楔块,形成管道的收缩。爆轰波在通过楔块时会发生Mach反射。利用烟熏玻璃片记录到了爆轰波Mach反射时形成的三波点迹线及其两侧胞格尺寸和密度的变化。据我们掌握的资料,这是首次用胞格结构变化的记录证实,气相爆轰波与无化学反应的空气中的冲击波一样,在一定的入射条件下会发生Mach反射。这一实验结果可使我们更深入了解爆轰波的本质,也为数值模拟气相爆轰波在障碍物上Mach反射现象提供了可对比的依据。     

The criterion of the existence or inexistence of transverse shock wave at wedge supported oblique detonation wave

A simplified theoretic method and numerical simulations were carried out to investigate the characterization of propagation of transverse shock wave at wedge supported oblique detonation wave.After solution validation,a criterion which is associated with the ratio Φ (u 2 /u CJ) of existence or inexistence of the transverse shock wave at the region of the primary triple was deduced systematically by 38 cases.It is observed that for abrupt oblique shock wave (OSW)/oblique detonation wave (ODW) transition,a transverse shock wave is generated at the region of the primary triple when Φ < 1,however,such a transverse shock wave does not take place for the smooth OSW/ODW transition when Φ > 1.The parameter Φ can be expressed as the Mach number behind the ODW front for stable CJ detonation.When 0.9 < Φ < 1.0,the reflected shock wave can pass across the contact discontinuity and interact with transverse waves which are originating from the ODW front.When 0.8 < Φ < 0.9,the reflected shock wave can not pass across the contact discontinuity and only reflects at the contact discontinuity.The condition (0.8 < Φ < 0.9) agrees well with the ratio (D ave /D CJ) in the critical detonation.     

A study of the interaction between two triple points

In the Mach reflection of plane shock on a concave double wedge, after two triple points collide with each other, the wave pattern is usually complicated. In this paper, firstly, a shock dynamic approach is used for studying this problem. In this approach, the method of shock-shock polar is used for better understanding the pattern of disturbance propagation. A downward-traveling shock-shock disturbance on the Mach stem is predicted theoretically. Secondly, based on the idea of shock dynamic approach, a gas dynamic model is built for studying the same problem. A similar result is obtained and the formation of the downward-traveling triple point is analyzed. This downward-traveling disturbance propagates and reflects between the upward-traveling shock-shock locus and the wall surface, causing the Mach number of Mach stem to increase and making the wave configuration approach to the one in the Mach reflection on a single wedge.Received: 19 April 2004, Accepted: 2 December 2004, Published online: 16 March 2005[/PUBLISHED]Correspondence to: P. Xie, Z.Y. Han     

A weak shock wave reflection over wedges

When a weak shock wave reflects from wedges its reflection pattern does not appear to be a simple Mach reflection. This reflection pattern is known to be von Neumann Mach reflection in which a Mach stem can not necessarily be straight. In this paper the local change of the Mach stem curvature was experimentally and numerically investigated. A distinct triple point, at which the curvature becomes infinite as appears in a simple Mach reflection, was not observed but the Mach stem curvature became a maximum between foot of the Mach stem and a point, P₁, at which an incident shock met with a reflected shock. Maximum curvature point P₂ and P₁ do not coincide for small wedge angles and tend to merge over a certain wedge angle. Experimental results agreed with numerical results. The trajectory angle of P₂ was found to be expressed well by Whitham's shock-shock angle.This article was processed using Springer-Verlag T_EX Shock Waves macro package 1.0 and the AMS fonts, developed by the American Mathematical Society.     

Mechanisms of detonation transmission in layered H2-O2 mixtures

When a plane detonation propagating through an explosive comes into contact with a bounding explosive, different types of diffraction patterns, which may result in the transmission of a detonation into the bounding mixture, are observed. The nature of these diffraction patterns and the mode of detonation transmission depend on the properties of the primary and bounding explosives. An experimental and analytical study of such diffractions, which are fundamental to many explosive applications, has been conducted in a two channel shock tube, using H₂-O₂ mixtures of different equivalence ratios as the primary and bounding or secondary explosive. The combination of mixtures was varied from rich primary / lean secondary to lean primary / rich secondary since the nature of the diffraction was found to depend on whether the Chapman-Jouguet velocity of the primary mixture,D _p, was greater than or less than that of the secondary mixture,D _s. Schlieren framing photographs of the different diffraction patterns were obtained and used to measure shock and oblique detonation wave angles and velocities for the different diffraction patterns, and these were compared with the results of a steady-state shock-polar solution of the diffraction problem. Two basic types of diffraction and modes of detonation reinitiation were observed. WhenD _p>D _s, an oblique shock connecting the primary detonation to an oblique detonation in the secondary mixture was observed. WithD _p<D _s, two modes of reinitiation were observed. In some cases, ignition occurs behind the Mach reflection of the shock wave, which is transmitted into the secondary mixture when the primary detonation first comes into contact with it, from the walls of the shock tube. In other cases, a detonation is initiated in the secondary mixture when the reflected shock crosses the contact surface behind the incident detonation. These observed modes of Mach stem and contact surface ignition have also been observed in numerical simulations of layered detonation interactions, as has the combined oblique-shock oblique-detonation configuration whenD _p>D _s. WhenD _p>D _s, the primary wave acts like a wedge moving into the secondary mixture with velocityD _p after steady state has been reached, a configuration which also arises in oblique-detonation ramjets and hypervelocity drivers.     

Oblique reflection of shock waves from rigid porous materials

A study to determine the general gas dynamic behaviour associated with the impact of a shock wave on a porous wedge has been undertaken. A number of interesting features are noted. The pattern of wave reflection is shown to be significantly affected by the inflow of gas into the wedge. This has the effect of reducing the triple point trajectory angle for cases of Mach reflection and for strongly reducing the reflection angle in regular reflection. The permeability of the wedge has a significant effect on the strength of the reflected wave and in some cases this wave can be attenuated to the extent that it is almost eradicated. Pressure measurements taken under the wedge are characterized by oscillations which are of similar shape, for a given wedge, over a range of shock wave Mach numbers. It is shown that the wave transmitted into the wedge is attenuated to varying degrees depending on the material properties, and that for weak incident waves the mean propagation velocity can be less than the sound speed in the pore fluid. Photographs taken using a specially constructed wedge which allows the transmitted wave to be visualised, show that the transmitted wave is nearly plane.This article was processed using Springer-Verlag T_EX Shock Waves macro package 1.0 and the AMS fonts, developed by the American Mathematical Society.     

爆轰波与激波对撞爆轰状态演化机理研究

对当量比氢氧混合气体中爆轰波与激波的正面对撞过程进行了二维数值研究. 采用了二阶精度NND差分格式与改进的两阶段化学反应模型,并以数值x-t纹影图以及烟迹图记录了对撞过程. 数值研究表明,透射爆轰波受到膨胀影响首先会衰减,甚至产生局部解耦现象;然后由于三波点的碰撞又能再次重新耦合. 在爆轰波对撞过程中,由于燃烧不均匀性而产生的弱横波对爆轰胞格的形成起着重要作用.      

不稳定性对爆轰波楔面马赫反射的影响规律研究

采用一种两步化学反应模型对胞格爆轰波的楔面马赫反射过程进行了数值研究,从而澄清和解释胞格不稳定性对马赫反射发展模式和自相似性的影响。考虑到反应欧拉方程源项的刚性问题,本文采用附加RungeKutta方法耦合非刚性对流项和刚性反应源项,对流项的离散采用五阶精度的WENO格式。计算结果表明,对于稳定胞格爆轰波而言,其马赫反射过程本质上与ZND爆轰波的马赫反射是一致的,整体上不存在自相似性,胞格不稳定性只是造成了三波点轨迹线局部小振幅的波动。在楔面顶点附近,由于马赫杆是强过驱的,爆轰波的马赫反射过程是自相似的。在远场,爆轰波马赫反射的三波点轨迹线渐近的趋向于一条直线,说明重新获得了自相似性。对于不稳定的爆轰波,由于自身的不稳定性可以与马赫反射的强度相匹配,定义其三波点的轨迹是困难的,进行自相似性分析没有意义。     

Three-dimensional effects on regular reflection in steady supersonic flows

The reflection of shock waves between two symmetrical wedges is investigated for the case of three-dimensional flows. Oblique shadowgraphs at various optical angles of yaw and pitch were used to examine the nature of fully three-dimensional flows, with wedge aspect ratios as low as 0.25 being considered. These images were used to construct surface models of the overall flow field for various reflection patterns and aspect ratios, which provides a visual indication of the flow field shape. For a Mach number of 3.1, and suitable wedge angles, the flow field with regular reflection on the tunnel centreline and Mach reflection further out is examined. The point of transition from regular reflection to the peripheral Mach surfaces is identified for various wedge angles and aspect ratios. It is shown that the transition points move outwards from the central plane as the aspect ratio decreases. This shows that three-dimensional flows favor regular reflection, because of the increasing curvature of the incident shock as the wedge becomes narrower, causing a decrease in the local angle of incidence. The height of the Mach stem is shown to be highly dependent on the geometry of the test wedge models. The Mach stem height decreases with aspect ratio due to the three-dimensional relieving effect, where the increase in lateral flow relieves the pressure over the surfaces of the wedges. Experimental evidence of the existence of the strong oblique shock solution in steady flows is presented.Received: 7 July 2003, Revised: 20 October 2003, Accepted: 6 November 2003, Published online: 10 February 2004PACS: 47.40.Nm Correspondence to: B.W. Skews     

Effect of reflection type on detonation initiation at shock-wave focusing

Abstract. From practical and theoretical standpoints, the initiation of combustion in gaseous media due to the shock waves focusing process at various reflectors is a subject of much current interest. The complex gas flowfield coupled with chemical kinetics provides a wide spectrum of possible regimes of combustion, such as fast flames, deflagration, detonation etc. Shock wave reflection at concave surfaces or wedges causes converging of the flow and produces local zones with extremely high pressures and temperatures. The present work deals with the initiation of detonation due to shock waves focusing at parabolic and wedge reflectors. Particular attention has been given to the determination of the critical values of the incident shock wave (ISW) Mach number, parameters of the combustible mixture, and geometrical sizes of reflector at which different combustion regimes could be generated. Received 30 August 1999 / Accepted 23 February 2000     

金属铅在斜冲击波对碰加载下动态行为的数值模拟

高强度冲击加载作用下金属材料的动态物理行为是当前冲击波领域基础研究和工程应用最为关注的焦点。采用光滑粒子法(SPH)开展不同位置起爆诱发的斜冲击波对碰加载金属铅的二维数值模拟研究,得到了金属铅内入射斜冲击波的角度和强度,并利用极曲线方法理论上导出发生马赫反射时的临界入射角和入射马赫数关系。根据计算结果可知,金属铅内入射斜波对碰后将发生马赫反射。随着起爆位置与金属铅表面距离的增加,不仅金属铅内入射冲击波强度和入射角增加,而且形成的马赫杆宽度也在增加。由自由面速度剖面给出了马赫杆宽度及张角,结果与理论预测的结果吻合较好。     

可燃气体中激波聚焦的点火特性

数值模拟了二维平面激波从抛物面上反射在可燃气体中聚焦的过程，研究了形 成爆轰波的点火特性. 对理想化学当量比氢气/空气混合气体，在初始压强20kPa的条件下， 马赫数2.6-2.8的激波聚焦能产生两个点火区：第1个点火区是反射激波会聚引起的，第 2个点火区是由入射激波在抛物面上发生马赫反射引起的. 这种条件下流场中会出现爆燃转 爆轰，起爆点分别分布在管道壁面、抛物反射面和第2点火区附近. 起爆机理分别为激波管 道壁面反射、点火诱导激波的抛物面反射和点火诱导的激波与第2点火区产生的爆燃波的相 互作用. 不同的点火和起爆过程导致了不同的流场波系结构，同时影响了爆轰波传播的波动 力学过程.     

超音速来流中爆轰波衍射和二次起爆过程研究

预爆管技术被广泛地应用在爆轰波发动机的起爆过程中，但是在超音速来流中基于预爆管技术起始爆轰波的研究并未被广泛地开展。基于此，本文中数值研究了横向超音速来流对半自由空间内爆轰波的衍射和自发二次起爆、及管道内的衍射和壁面反射二次起爆两种现象的影响。数值模拟的控制方程为二维欧拉方程，空间上使用五阶WENO格式进行数值离散，采用带有诱导步的两步链分支化学反应模型。所模拟的爆轰波具有规则的胞格结构，对应于用惰性气体高度稀释过的可爆混合物中形成的爆轰波。结果表明:在半自由空间内，在本文所模拟的几何尺寸下，爆轰波并未成功发生二次起爆现象，但是爆轰波的自持传播距离随着横向超音速来流强度的增强而增加。在核心的三角形流动区域外，波面诱导产生了更多的横波结构；在管道内，横向的超音速来流在逆流侧对出口气流产生了压缩作用，能有效提高波面压力，因此反射后的激波压力也比较高。在同样的几何尺寸下，爆轰波在静止和超音速(Ma=2.0)气流中分别出现了二次起爆失败和成功两种现象，这是由于在超音速来流中化学反应面的褶皱诱导产生了横波结构，横波与管壁以及其他横波之间的碰撞提高了前导激波的强度，并最终促进了爆轰波在超声速流主管道内的成功起始。     

爆轰波在突扩通道中传播的数值模拟研究

建立了描述甲烷 空气混合物爆轰波传播的单步化学反应爆轰模型 ,通过数值模拟研究了在二维突扩通道中爆轰波的强度变化和各种波行为。结果表明 :爆轰波在进入突扩通道初始阶段的衍射使爆轰波局部向爆燃转变 ;爆炸波在壁面发生马赫反射形成的高温高压区域将直接诱导自持爆轰波的重新形成。     

带隔板装药爆轰波马赫反射理论研究和数值模拟

基于三波理论和Whitham方法对带隔板装药爆轰波相互作用后发生的正规反射和非正规反射进行了理论分析,给出了爆轰波发生马赫反射时临界入射角和马赫杆增长角等参数的变化规律,提出了马赫杆高度的计算模型。基于凝聚炸药爆轰Jones-Wilkins-Lee(JWL)模型和冲击起爆的Lee-Tarver模型,利用有限元计算软件对带隔板装药爆轰波的传播过程进行了数值模拟。结果表明,发生马赫反射后,随着爆轰波的传播,马赫杆的高度不断增加。数值模拟结果与理论计算结果吻合较好,说明本文中采用的理论模型和数值模拟方法能够较准确地描述带隔板装药爆轰波马赫反射的传播过程。     

Experimental investigation of the asymptotically approached Mach reflection over the second surface in a double wedge reflection

The assumption that the Mach reflection which is formed over the second surface of a double wedge with angles _w ¹ and kw/2 approaches asymptotically the Mach reflection which would have been obtained by an identical incident shock wave over a single wedge with an angle _w = _w ² was verified experimentally. The verification of this assumption supports the shock polar analysis suggested by Ben-Dor et al. (1987) for the study of the reflection process of a planar shock wave over a double wedge. Measurements of the rate of approach to the asymptotic value are also provided.     

Diffuse holographic interferometric observation of shock wave reflection from a skewed wedge

The pattern of shock wave reflection over a wedge is, in general, either a regular reflection or a Mach reflection, depending on wedge angles, shock wave Mach numbers, and specific heat ratios of gases. However, regular and Mach reflections can coexist, in particular, over a three-dimensional wedge surface, whose inclination angles locally vary normal to the direction of shock propagation. This paper reports a result of diffuse double exposure holographic interferometric observations of shock wave reflections over a skewed wedge surface placed in a 100 × 180 mm shock tube. The wedge consists of a straight generating line whose local inclination angle varies continuously from 30° to 60°. Painting its surface with fluorescent spray paint and irradiating its surface with a collimated object beam at a time interval of a few microseconds, we succeeded in visualizing three-dimensional shock reflection over the skewed wedge surface. Experiments were performed at shock Mach numbers, 1.55, 2.02, and 2.53 in air. From reconstructed holographic images, we estimated critical transition angles at these shock wave Mach numbers and found that these were very close to those over straight wedges. This is attributable to the flow three-dimensionality.