The effects of annealing on Au/pyronine-B/MD n-InP Schottky structure

Thin film of non-polymeric organic compound pyronine-B has been fabricated on moderately doped (MD) n-InP substrate as an interfacial layer using spin coating technique for the electronic modification of Au/MD n-InP Schottky contact. The electrical characteristics have been determined at room temperature. The barrier height and the ideality factor values for Au/pyronine-B/MD n-InP Schottky diode have been obtained from the forward bias I-V characteristics at room temperature as 0.60 eV and 1.041; 0.571 and 1.253 eV after annealing at 100 and 250 °C, respectively. An increase in annealing temperature at the Au/n-InP Schottky junction is shown to increase the reverse bias leakage current by about one order of magnitude and decrease the Schottky barrier height by 0.027 eV. Furthermore, the barrier height values for the Au/pyronine-B/MD n-InP Schottky diode have also been obtained from the C-V characteristics at room temperature as 1.001 and 0.709 eV after annealing at 100 and 250 °C, respectively. Finally, it was seen that the diode parameters changed with increase in the annealing temperature.     

Effect of annealing on the electronic parameters of Au/poly(ethylmethacrylate)/n-InP Schottky diode with organic interlayer

A thin poly(ethylmethacrylate) (PEMA) layer is deposited on n-InP as an interlayer for electronic modification of Au/n-InP Schottky structure. The electrical properties of Au/PEMA/n-InP Schottky diode have been investigated by current–voltage (I–V) and capacitance–voltage (C–V) measurements at different annealing temperatures. Experimental results show that Au/PEMA/n-InP structure exhibit a good rectifying behavior. An effective barrier height as high as 0.83 eV (I–V) and 1.09 eV (C–V) is achieved for the Au/PEMA/n-InP Schottky structure after annealing at 150 °C compared to the as-deposited and annealed at 100 and 200 °C. Modified Norde's functions and Cheung method are also employed to calculate the barrier height, series resistance and ideality factors. Results show that the barrier height increases upon annealing at 150 °C and then slightly decreases after annealing at 200 °C. The PEMA layer increases the effective barrier height of the structure as this layer creates a physical barrier between the Au metal and the n-InP. Terman's method is used to determine the interface state density and it is found to be 5.141 × 10¹² and 4.660 × 10¹² cm^?2 eV^?1 for the as-deposited and 200 °C annealed Au/PEMA/n-InP Schottky diodes. Finally, it is observed that the Schottky diode parameters change with increasing annealing temperature.     

Effect of annealing temperature on the electrical properties of Au/Ta2O5/n-GaN metal–insulator–semiconductor (MIS) structure

We report on the effect of an annealing temperature on the electrical properties of Au/Ta₂O₅/n-GaN metal–insulator–semiconductor (MIS) structure by current–voltage (I–V) and capacitance–voltage (C–V) measurements. The measured Schottky barrier height (Φ _bo) and ideality factor n values of the as-deposited Au/Ta₂O₅/n-GaN MIS structure are 0.93 eV (I–V) and 1.19. The barrier height (BH) increases to 1.03 eV and ideality factor decreases to 1.13 upon annealing at 500 ^°C for 1 min under nitrogen ambient. When the contact is annealed at 600 ^°C, the barrier height decreases and the ideality factor increases to 0.99 eV and 1.15. The barrier heights obtained from the C–V measurements are higher than those obtained from I–V measurements, and this indicates the existence of spatial inhomogeneity at the interface. Cheung’s functions are also used to calculate the barrier height (Φ _bo), ideality factor (n), and series resistance (R _s ) of the Au/Ta₂O₅/n-GaN MIS structure. Investigations reveal that the Schottky emission is the dominant mechanism and the Poole–Frenkel emission occurs only in the high voltage region. The energy distribution of interface states is determined from the forward bias I–V characteristics by taking into account the bias dependence of the effective barrier height. It is observed that the density value of interface states for the annealed samples with interfacial layer is lower than that of the density value of interface states of the as-deposited sample.     

Influence of rapid thermal annealing on electrical and structural properties of double metal structure Au/Ni/n-InP (1 1 1) diodes

The effect of rapid thermal annealing on the electrical and structural properties of Ni/Au Schottky contacts on n-InP have been investigated by current–voltage (I–V), capacitance–voltage (C–V), auger electron spectroscopy (AES) and X-ray diffraction (XRD) techniques. The Au/Ni/n-InP Schottky contacts are rapid thermally annealed in the temperature range of 200–500 °C for a duration of 1 min. The Schottky barrier height of as-deposited Ni/Au Schottky contact has been found to be 0.50 eV (I–V) and 0.86 eV (C–V), respectively. It has been found that the Schottky barrier height decreased with increasing annealing temperature as compared to as-deposited sample. The barrier height values obtained are 0.43 eV (I–V), 0.72 eV (C–V) for the samples annealed at 200 °C, 0.45 eV (I–V) and 0.73 eV (C–V) for those at 400 °C. Further increase in annealing temperature to 500 °C the barrier height slightly increased to 0.46 eV (I–V) and 0.78 eV (C–V) compared to the values obtained for the samples annealed at 200 °C and 400 °C. AES and XRD studies showed the formation of indium phases at the Ni/Au and InP interface and may be the reason for the increase in barrier height. The AFM results showed that there is no significant degradation in the surface morphology (rms roughness of 1.56 nm) of the contact even after annealing at 500 °C.     

Effects of chemical treatment on barrier height and ideality factors of Au/GaN Schottky diodes

We have studied Au/n-GaN Schottky barrier diodes. GaN surfaces have been prepared by cleaning in HCl and (NH₄)₂S prior to metal deposition. The zero-biased barrier heights and ideality factors obtained from the current-voltage characteristics differ from diode to diode, although all the samples were prepared identically. The statistical analysis for the reverse bias C-V data yielded mean value of (1.35±0.04) eV for Schottky barrier height of HCl treated sample and (1.20±0.03) eV for (NH₄)₂S sample, where 9 dots were considered from each cleaning method. It was found that the barrier height values obtained from the C⁻²-V (1.43 eV) and I-V characteristics (0.89 eV) are different from each other by 0.54 eV. The inhomogeneous barrier heights were found to be related to the effect of the high series resistance on diode parameters (Akkiliç et al., 2004) [1].     

Comparison of electrical parameters of Zn/p-Si and Sn/p-Si Schottky barrier diodes

In this study, current-voltage (I-V) and capacitance-voltage (C-V) characteristics of metal-semiconductor (MS) Zn/p-Si and Sn/p-Si Schottky diodes, with high resistivity silicon structures, are investigated. The parameters of series resistance (R_S), the ideality factor (n) and the barrier height (Φ_b) are determined by performing different plots from the forward bias current-voltage (I-V) and reverse bias capacitance-voltage (C-V) characteristics. Thus, the barrier heights (Φ_b) for the Si Schottky diodes obtained between 0.725 and 1.051 eV, the ideality factor (n) between 1.043 and 1.309, and the series resistance (R_S) between 12.594 and 12.950 kΩ. The energy distribution of interface states density was determined from the forward bias I-V characteristics by taking into account the bias dependence of the effective barrier height. It was concluded that the density of interface states in the considered energy range are in close agreement with each other values obtained for Zn/p-Si and Sn/p-Si Schottky diodes.     

Correlation between barrier heights and ideality factors of Cd/n-Si and Cd/p-Si Schottky barrier diodes

Our goal is to experimentally investigate whether or not the effective Schottky barrier heights (SBHs) and ideality factors obtained from the current-voltage (I-V) and capacitance-voltage (C-V) characteristics differ from diode to diode even if the samples were identically prepared. For this purpose, we prepared Cd/n-Si (33 dots) and Cd/p-Si (15 dots) diodes. The SBH for the Cd/n-Si diodes ranged from 0.701 to 0.605 eV, and ideality factor n from 1.913 to 1.213. Φ_b value for the Cd/p-Si diodes ranged from 0.688 to 0.730 eV, and ideality factor n value from 1.473 to 1.040. The experimental SBH distributions obtained from the C⁻²-V and I-V characteristics were fitted by a Gaussian function and their mean SBH values were calculated. Furthermore, the laterally homogeneous barrier heights were also computed from the extrapolation of the linear plot of experimental barrier heights versus ideality factors.     

Fabrication and electrical characterization of Au/p-Si/STO/Au contact

Au/STO/p-Si/Au structure is fabricated using pulsed laser deposition technique at room temperature. The current–voltage (I–V) characteristics of the device show rectification behavior. Various junction parameters such as ideality factor, barrier height and series resistance is determined using conventional forward bias I–V characteristics, Cheung method and Norde’s function. Au/STO/p-Si/Au structure shows non-ideal diode characteristics with the value of ideality factor of ∼5.1 and barrier height of ∼0.40 eV.     

Barrier characteristics of biopolymer-based organic/inorganic Au/CTS/n-InP hybrid junctions

Thin film of biopolymeric compound chitosan (CTS) has been surfaced on moderately doped n-InP substrate as an interfacial layer by means of spin coating for the electronic modification of Au/n-InP structure. Electrical characterization of Au/CTS/n-InP hybrid junction has been performed by I–V and C–V measurements at room temperature. An effective barrier height (BH) value of 0.678 eV and an ideality factor of n = 1.665 have been obtained for the hybrid junction. The CTS interfacial layer has been found to reduce the reverse bias leakage current of the junction by about three orders of magnitude and enhance the BH by about 0.213 eV. Furthermore, the BH value of the hybrid junction has been obtained as 0.693 eV by C–V measurement. Good performance of the device could be ascribed to the passivation effect of the CTS interfacial layer between Au and n-InP. The BH values of 0.678 and 0.693 eV for the hybrid junction have been significantly higher than that of the conventional Au/n-InP junction (~0.465 eV). The results indicated that biopolymeric thin interfacial CTS layer might lead to the modification of the potential barrier for metal/n-InP junctions. Moreover, band gap of the CTS layer has been determined as 4.60 eV via UV–vis spectroscopy.     

Characterization of Al/Si junctions on Si(100) wafers with chemical vapor deposition-based sulfur passivation

Chemical vapor deposition-based sulfur passivation using hydrogen sulfide is carried out on both n-type and p-type Si(100) wafers. Al contacts are fabricated on sulfur-passivated Si(100) wafers and the resultant Schottky barriers are characterized with current–voltage (I–V), capacitance–voltage (C–V) and activation-energy methods. Al/S-passivated n-type Si(100) junctions exhibit ohmic behavior with a barrier height of <0.078 eV by the I–V method and significantly lower than 0.08 eV by the activation-energy method. For Al/S-passivated p-type Si(100) junctions, the barrier height is ~0.77 eV by I–V and activation-energy methods and 1.14 eV by the C–V method. The discrepancy between C–V and other methods is explained by image force-induced barrier lowering and edge-leakage current. The I–V behavior of an Al/S-passivated p-type Si(100) junction remains largely unchanged after 300 °C annealing in air. It is also discovered that heating the S-passivated Si(100) wafer before Al deposition significantly improves the thermal stability of an Al/S-passivated n-type Si(100) junction to 500 °C.     

Analysis of current–voltage and capacitance–voltage characteristics of perylene-monoimide/n-Si Schottky contacts

The electrical and interface state properties of Au/perylene-monoimide (PMI)/n-Si Schottky barrier diode have been investigated by current–voltage (I–V) and capacitance–voltage (C–V) measurements at room temperature. A good rectifying behavior was seen from the I–V characteristics. The series resistance (R_s) values were determined from I–V and C–V characteristics and were found to be 160 Ω and 53 Ω, respectively. The barrier height (Φ_b) of Au/PMI/n-Si Schottky diode was found to be 0.694 eV (I–V) and 0.826 eV (C–V). The ideality factor (n) was obtained to be 4.27 from the forward bias I–V characteristics. The energy distribution of interface state density (N_ss) of the PMI-based structure was determined, and the energy values of N_ss were found in the range from E_c ? 0.508 eV to E_c ? 0.569 eV with the exponential growth from midgap toward the bottom of the conduction band. The values of the N_ss without R_s are 2.11 × 10¹² eV^?1 cm^?2 at E_c ? 0.508 eV and 2.00 × 10¹² eV^?1 cm^?2 at E_c ? 0.569 eV. Based on the above results, it is clear that modification of the interfacial potential barrier for metal/n-Si structures has been achieved using a thin interlayer of the perylene-monomide.     

Schottky barrier properties of various metal (Zr, Ti, Cr, Pt) contact on p-GaN revealed from I-V-T measurement

Schottky barrier contact using three different metal (Zr, Ti, Cr and Pt) and Ohmic contact using Ni were made on same epitaxial growth layer of p-GaN. Measurements were carried out using current-voltage-temperature (I-V-T) in the range of 27-100°C. Under forward bias and room-temperature (RT), the ideality factors (η) were determined to be 2.38, 1.82, 1.51 and 2.63, respectively, for Zr, Ti, Cr and Pt. The Schottky barrier height (SBH) and effective Richardson coefficient A^** were measured through modified Norde plot as one of the analysis tools. Barrier heights of 0.84, 0.82, 0.77 and 0.41 eV for Zr, Ti, Cr and Pt, respectively, were obtained from the modified Norde plot. Schottky barrier heights of Zr, Ti, or Cr/p-GaN were also measured through activation energy plot, and determined to be in the same range (∼0.87 eV) and Pt at 0.49 eV. These results indicate that the Fermi level seems to be pinned due to the value of slope parameter (S) was very low (S = −0.25).     

Electronic and interface state density distribution properties of Ag/p-Si Schottky diode

Electronic and interface state distribution properties of Ag/p-Si Schottky diode have been investigated. The diode indicates non-ideal current-voltage behavior with an ideality factor greater than unity. The capacitance-voltage (C-V) characteristic is linear in reverse bias indicating rectification behavior and charge density within depletion layer is uniform. From I-V and C-V characteristics, junction parameters such as diode ideality factor and barrier height were found as 1.66 and ?_B(I-V) = 0.84 eV (?_B(C-V) = 0.90 eV), respectively. The interface state density N_ss and relaxation time τ of the Schottky diode were determined by means of Schottky capacitance spectroscopy method. The results show the presence of thin interfacial layer between the metal and semiconductor.     

Molecular control over Ag/p-Si diode by organic layer

Electrical transport properties of Ag metal-fluorescein sodium salt (FSS) organic layer-silicon junction have been investigated. The current-voltage (I-V) characteristics of the diode show rectifying behavior consistent with a potential barrier formed at the interface. The diode indicates a non-ideal I-V behavior with an ideality factor higher than unity. The ideality factor of the Ag/FSS/p-Si diode decreases with increasing temperature and the barrier height increases with increasing temperature. The barrier height (φ_b=0.98 eV) obtained from the capacitance-voltage (C-V) curve is higher than barrier height (φ_b=0.72 eV) derived from the I-V measurements. The barrier height of the Ag/FSS/p-Si Schottky diode at the room temperature is significantly larger than that of the Ag/p-Si Schottky diode. It is evaluated that the FSS organic layer controls electrical charge transport properties of Ag/p-Si diode by excluding effects of the SiO₂ residual oxides on the hybrid diode.     

The barrier-height inhomogeneity in identically prepared Ni/n-type 6H-SiC Schottky diodes

The effective barrier heights and ideality factors of identically fabricated Ni/n-type 6 H-SiC Schottky diodes (23 dots) have been calculated from their experimental forward bias current–voltage (I–V) and reverse bias capacitance–voltage (C–V) characteristics. A statistical study related to the experimental barrier heights (BHs) and ideality factors of the diodes has been made. The effective Schottky barrier heights (SBHs) and ideality factors obtained from the I–V and C–V characteristics have differed from diode to diode. The BHs obtained from the I–V characteristics varied from 0.85 to 1.03 eV, the ideality factors varied from 1.13 to 1.40 and the BHs from C^-2–V characteristics varied from 1.10 to 1.70 eV. The experimental BH and ideality factor distributions obtained from the I–V characteristics are fitted by a Gaussian function, and their mean values are found to be 0.92±0.04 eV and 1.29±0.08 eV, respectively. The lateral homogeneous SBH value of 1.16 eV for the Ni/n-type 6H-SiC diodes has been calculated from a linear extrapolation of the effective barrier heights to n_if=1.03. PACS 79.40.+z; 73.40.Sx; 73.30.+y; 71.20.Nr     

Effect of diode size and series resistance on barrier height and ideality factor in nearly ideal Au/n type-GaAs micro Schottky contact diodes

Small high-quality Au/n type-GaAs Schottky barrier diodes (SBDs) with low reverse leakage current are produced using lithography. Their effective barrier heights (BHs) and ideality factors from current-voltage (I-V) characteristics are measured by a Pico ampere meter and home-built I-V instrument. In spite of the identical preparation of the diodes there is a diode-to-diode variation in ideality factor and barrier height parameters. Measurement of topology of a surface of a thin metal film with atomic force microscope (AFM) shows that Au-n type-GaAS SD consists of a set of parallel-connected micro and nanocontacts diodes with sizes approximately in a range of 100-200 nm. Between barrier height and ideality factor there is an inversely proportional dependency. With the diameter of contact increasing from 5 μm up to 200 μm, the barrier height increases from 0.833 up to 0.933 eV and its ideality factor decreases from 1.11 down to 1.006. These dependencies show the reduction of the contribution of the peripheral current with the diameter of contact increasing. We find the effect of series resistance on barrier height and ideality factor.     

Temperature-Dependent Current–Voltage (I–V) and Capacitance–Voltage (C–V) Characteristics of Ni/Cu/n-InP Schottky Barrier Diodes

The current-voltage (I–V) and capacitance-voltage (C–V) characteristics of Ni/Cu/n-InP Schottky barrier diodes are studied over a wide temperature range, from 210 K to 420 K. The I–V characteristics display anomalous thermal behavior. The apparent barrier height decays, and the ideality factor grows at low temperatures, and the series resistances resulting from Cheung’s and Norde’s procedures are markedly temperature dependent. The nonlinearity of the Richardson plot and the strong temperature dependence of the Schottky-barrier parameters indicate that the interface is spatially inhomogeneous. Plots of the zero-bias barrier height as a function of 1/(2kT) points to a Gaussian distribution of barrier heights with 0.90 eV mean height and 0.014 eV standard deviation. When this distribution is accounted for, a Richardson of 6.5 A/(cm K)² results, relatively close to the 9.4/(cm K)² predicted by theory. We conclude that, combined with a Gaussian distribution of barrier heights, the thermionic-emission mechanism explains the temperature-dependent I–V and C–V characteristics of the studied Schottky-barrier diodes.     

Effects of ageing on the electrical characteristics of Cd/CdS/n-Si/Au–Sb structure deposited by SILAR method

Cd/CdS/n-Si/Au–Sb structure has been fabricated by the Successive Ionic Layer Adsorption and Reaction (SILAR) method and the influence of the time dependent or ageing on the characteristic parameters are examined. The current–voltage (I–V), capacitance–voltage (C–V) and capacitance–frequency (C–f) characteristics of the structure have been measured immediately, 1, 3, 5, 15, 30, 45, 60, 75, 90, 105, 120, 135, 150 and 165 days after fabrication of the structure. The characteristic parameters of the structure such as barrier height, ideality factor, series resistance are calculated from the I–V measurements and the barrier height, carrier concentration values are calculated from reverse bias C^?2–V measurements at 500 kHz and room temperature. Furthermore, the density distribution and time constant of the interface states have been calculated from the C–f measurements using the Schottky Capacitance Spectroscopy method as a function of ageing time. It has been seen that the changes of characteristic parameters such as barrier height, ideality factor and series resistance of Cd/CdS/n-Si/Au–Sb structure have lightly changed with increasing ageing time. At the same time, the rectifying ratio of the device increases with ageing time. It can be clearly said that the I–V characteristics of device get better with time.     

Laterally inhomogeneous barrier analysis of the methyl violet/p-Si organic/inorganic hybrid Schottky structures

In this work, we have investigated the electrical characteristics, such as current-voltage (I-V) and capacitance-voltage (C-V) measurements, of identically prepared crystal violet/p-Si Organic/Inorganic (OI) Schottky structures formed by evaporation of organic compound solution to directly p-Si semiconductor substrate. It has been seen that the crystal violet organic dye thin film on the p-Si substrate has exhibited a good rectifying behavior. The barrier heights (BHs) and ideality factors of all devices have been calculated from the electrical characteristics. Although the diodes were all identically prepared, there was a diode-to-diode variation: the effective barrier heights ranged from 0.6 ± 0.1 to 0.8 ± 0.1 eV, and the ideality factor from 1.6 ± 0.4 to 3.5 ± 0.4. The barrier height versus ideality factor plot has been plotted for the OI devices. Lateral homogeneous BH was calculated as a value of 0.7 eV from the observed linear correlation between BH and ideality factor, which can be explained by laterally inhomogeneities of BHs. The values of barrier height and acceptor doping concentration yielded from the reverse bias C-V measurements ranged from 0.7 ± 0.1 to 1.3 ± 0.1 eV and from (4.7 ± 0.8) × 10¹⁴ to (8.1 ± 0.8) × 10¹⁴ cm⁻³, respectively. The mean barrier height and mean acceptor doping concentration from C-V characteristics has been calculated 1.0 eV and 5.9 × 10¹⁴ cm⁻³, respectively. It has been seen that the mean BH value of 0.7 eV obtained for the Al/methyl violet/p-Si contact is significantly larger than BH values of the conventional Al/p-Si Schottky diodes. Thus, modification of the interfacial potential barrier for metal/Si diodes has been achieved using a thin interlayer of the methyl violet organic semiconductor; this has been ascribed to the fact that the methyl violet interlayer increases the effective barrier height by influencing the space charge region of Si.     

Investigation of electrical properties of HfO2 metal–insulator–metal (MIM) devices

This paper is devoted to the study of the electrical properties of Au/HfO₂/TiN metal–insulator–metal (MIM) capacitors in three distinctive modes: (1) alternative mode (C–f), (2) dynamic regime [thermally stimulated currents, TSCs I(T)] and (3) static mode [I(V)]. The electrical parameters are investigated for different temperatures. It is found that capacitance frequency C–f characteristic possesses a low-frequency dispersion that arises for high temperature (T > 300 °C). Accordingly, the loss factor exhibits a dielectric relaxation (with an activation energy E _a ~ 1.13 eV) which is intrinsically related to the diffusion of oxygen vacancies. The relaxation mechanisms of electrical defects in a dynamic regime (TSCs) analysis show that defect related to the TSC peak observed at 148.5 °C (E _a ~ 1 eV) is in agreement with impedance spectroscopy (C–f). On the other hand, when the MIM structures are analyzed in static mode, the I–V plots are governed by Schottky emission. The extrapolation of the curve at zero field gives a barrier height of 1.7 eV.