Synthesis of novel magnetic sulfur-doped Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles for efficient removal of Pb(II)

In this work, we report the synthesis of magnetic sulfur-doped Fe₃O₄ nanoparticles (Fe₃O₄:S NPs) with a novel simple strategy, which includes low temperature multicomponent mixing and high temperature sintering. The prepared Fe₃O₄:S NPs exhibit a much better adsorption performance towards Pb(II) than bare Fe₃O₄ nanoparticles. FTIR, XPS, and XRD analyses suggested that the removal mechanisms of Pb(II) by Fe₃O₄:S NPs were associated with the process of precipitation (formation of PbS), hydrolysis, and surface adsorption. The kinetic studies showed that the adsorption data were described well by a pseudo second-order kinetic model, and the adsorption isotherms could be presented by Freundlich isotherm model. Moreover, the adsorption was not significantly affected by the coexisting ions, and the adsorbent could be easily separated from water by an external magnetic field after Pb(II) adsorption. Thus, Fe₃O₄:S NPs are supposed to be a good adsorbents for Pb(II) ions in environmental remediation.     

Magnetic solid-phase extraction of imatinib and doxorubicin as cytostatic drugs by Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/graphene oxide nanocomposite

Magnetic solid-phase extraction based on Fe₃O₄/graphene oxide nanocomposites was investigated for the separation, preconcentration and determination of imatinib and doxorubicin in aqueous solutions. Synthesis of Fe₃O₄/graphene oxide was characterized by transmission electron microscopy, energy-dispersive X-ray analyzer and vibrating sample magnetometer. After optimizing the conditions, optimal experimental conditions including sample pH, the amount of the magnetic nanoparticles, the effect of salt concentration and other chemotherapy medications, eluent type and extraction time were studied and established. The method showed good linearity for the determination of doxorubicin and imatinib in the concentration range of 0.01–100 μg mL^?1 in aqueous solutions with limit of detection 1.8 ng mL^?1 for doxorubicin and 1.9 ng mL^?1 for imatinib. The relative recoveries of doxorubicin and imatinib levels were 96.7 and 88.4%, respectively. The results indicate that the present procedure is a suitable method for extraction of imatinib and doxorubicin from environmental water samples.     

Adsorption behavior of <Superscript>99</Superscript>Tc on Fe,Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>

Summary The adsorption of ⁹⁹Tc on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ was studied by batch experiments under aerobic and anoxic conditions. The effects of pH and CO₃^2- concentration of the simulated ground water on the adsorption ratios were also investigated, and the valences of Tc in solution after the adsorption equilibrium were studied by solvent extraction. The adsorption isotherms of TcO₄- on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ were determined. Experimental results have shown that the adsorption ratio of Tc on Fe decreases with the increase of pH in the range of 5-12 and increases with the decrease of the CO₃^2- concentration in the range of 10^-8M-10^-2M. Under aerobic conditions, the adsorption ratios of ⁹⁹Tc on Fe₂O₃ and Fe₃O₄ were not influenced by pH and CO₃^2-concentration. When Fe was used as adsorbent, Tc existed mainly in the form of Tc(IV) after equilibrium and in the form of Tc(VII) when the adsorbent was Fe₂O₃ or Fe₃O₄ under aerobic conditions. The adsorption ratios of Tc on Fe, Fe₂O₃ and Fe₃O₄ decreased with the increase of pH in the range of 5-12 and increased with the decrease of the CO₃^2- concentration in the range of 10^-8M-10^-2M under anoxic conditions. Tc existed mainly in the form of Tc(IV) after equilibrium when Fe, Fe₂O₃ and Fe₃O₄ was the adsorbent under anoxic conditions. The adsorption isotherms of TcO_4- on the adsorbers Fe, Fe₂O₃ and Fe₃O₄ are fairly in agreement with the Freundlich’s equation under both aerobic and anoxic conditions.     

Magnetic nanoparticles (Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> &amp; Co<Subscript>3</Subscript>O<Subscript>4</Subscript>) and their applications in urea biosensing

Nanobiotechnology has opened a new and exciting opportunities for exploring urea biosensor based on magnetic nanoparticles (NPs) mainly Fe₃O₄ and Co₃O₄. These NPs have been extensively exploited to develop biosensors with stability, selectivity, reproducibility and fast response time. This review gives an overview of the development of urea biosensor based on Fe₃O₄ and Co₃O₄ for in vitro diagnostic applications along with significant improvements over the last few decades. Additionally, effort has been made to elaborate properties of magnetic nanoparticles (MNPs) in biosensing aspects. It also gives details of recent developments in hybrid nanobiocomposite based urea biosensor.     

Preparation and adsorption of magnetic Co<Subscript>0.5</Subscript>Ni<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>-chitosan nanoparticles

In this paper, magnetic chitosan microspheres were prepared by the emulsification cross-linking technique, with glutaraldehyde as the cross-linking agent, liquid paraffin as the dispersant, and the Span-80 as emulsifier. The time of cross-linking and the ratio of Co_0.5Ni_0.5Fe₂O₄/chitosan were investigated. The morphology was studied by different instruments. The adsorption performance was investigated and the effects of initial concentration of methyl orange, the time of cross-linking, and the amount of adsorbent were discussed. It is found that the product has uniform morphology when the ratio of magnetic Co_0.5Ni_0.5Fe₂O₄/chitosan is 1 : 2 and the time of cross-linking is 5 h; At room temperature, magnetic Co_0.5Ni_0.5Fe₂O₄–chitosan has a good adsorption toward methyl orange when the magnetic Co_0.5Ni_0.5Fe₂O₄/chitosan dosage is 20 mg.     

Stabilization of Oil-in-Water Emulsions with SiO<Subscript>2</Subscript> and Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles

Stabilization of oil-in-water Pickering emulsions with SiO₂ and Fe₃O₄ nanoparticles has been studied. Emulsions containing three-dimensional gel networks formed by aggregated nanoparticles in the dispersion media have been shown to be stable with respect to flocculation, coalescence, and creaming. Concentration ranges in which emulsions are kinetically stable have been determined. Stabilization with mixed Ludox HS-30 and Ludox CL SiO₂ nanoparticles leads to the formation of stable emulsions at a weight ratio between the nanoparticles equal to 2 and pH 6.7. In the case of stabilization with Ludox CL and Fe₃O₄ nanoparticles, systems resistant to aggregation and sedimentation are obtained at pH 8. The use of mixed Ludox HS-30 and Fe₃O₄ nanoparticles has not resulted in the formation of emulsions stable with respect to creaming, with such emulsions appearing to be resistant only to coalescence at pH 2–6.     

One-Pot Synthesis of Novel Amino-Functionalized Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Hybrid Microspheres for Cu(II) Removal from Aqueous Solutions

In this work, we report the development of novel amino-functionalized Fe₃O₄ hybrid microspheres adsorbent from a facial and one-step solvothermal route by using FeCl₃·6H₂O as a single iron source and 3-aminophenoxy-phthalonitrile as ource of amino groups. During solvothermal process, the nitrile groups of 3-aminophenoxy-phthalonitrile would bond with the Fe₃O₄ through the phthalocyanine cyclization reaction to form the amino-functionalized Fe₃O₄ magnetic nano-material, which was confirmed by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and thermo-gravimetric analyzer (TGA). From the scanning electron microscope (SEM) and transmission electron microscopy (TEM) observation, the resulting monodispersed amino-functionalized Fe₃O₄ hybrid microspheres with the diameters of 180–200 nm were synthesized via the self-assembly process. More importantly, as-prepared Fe₃O₄ nano-materials with abundant amino groups exhibited high separation efficiency when they were used to remove the Cu(II) from aqueous solutions. Furthermore, the adsorption isotherms of Fe₃O₄ nano-material for Cu(II) removal fitted the Langmuir isotherm model, in which the calculated maximum adsorption capacity could increase from 5.51 to 16.25 mg g^–1 at room temperature. This work demonstrated that the amino-functionalized Fe₃O₄ magnetic nano-materials were promising as efficient adsorbents for the removal of heavy metal ions from wastewater in low concentration.     

Improving Pullulanase Catalysis via Reversible Immobilization on Modified Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@Polydopamine Nanoparticles

To improve the catalysis of pullulanase from Anoxybacillus sp.WB42, Fe₃O₄@polydopamine nanoparticles (Fe₃O₄@PDA) were prepared and modified with functional groups for immobilization of pullulanases via covalent binding or ionic adsorption. Immobilized pullulanases had lower thermal stability than that of free pullulanase, whereas their catalysis depended on the surface characteristics of nanoparticles. As for covalent immobilization of pullulanases onto Fe₃O₄@PDA derivatives, the spacer grafted onto Fe₃O₄@PDA made the catalytic efficiency of pullulanase increase up to the equivalence of free enzyme but dramatically reduced the pullulanase thermostability. In contrast, pullulanases bounded ionically to Fe₃O₄@PDA derivatives had higher activity recovery and catalytic efficiency, and their catalytic behaviors varied with the modifier grafted onto Fe₃O₄@PDA. Among these immobilized pullulanases, ionic adsorption of pullulanase on Fe₃O₄@PDA-polyethyleneimine-glycidyltrimethylammonium gave a high-performance and durable catalyst, which displayed not only 1.5-fold increase in catalytic efficiency compared to free enzyme but also a significant improvement in operation stability with a half of initial activity after 27 consecutive cycles with a total reaction time of 13.5 h, and was reversible, making this nanoparticle reusable for immobilization.     

Preparation of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>-C18 nano-magnetic composite materials and their cleanup properties for organophosphorous pesticides

Magnetic Fe₃O₄-C18 composite nanoparticles of approximately 5–10 nm in size were synthesized and characterized by IR spectroscopy, atomic absorption spectroscopy, X-ray diffraction, and transmission electron microscopy. The magnetic Fe₃O₄-C18 composite nanoparticles were applied for cleanup and enrichment of organophosphorous pesticides. Comparative studies were carried out between magnetic Fe₃O₄-C18 composite nanoparticles and common C18 materials. Residues of organophosphorous pesticides were determined by gas chromatography in combination with a nitrogen/phosphorus detector. The cleanup and enrichment properties of magnetic Fe₃O₄-C18 composite nanoparticles are comparable with those of common C18 materials for enrichment of organophosphorous pesticides, but the cleanup and enrichment are faster and easier to perform. Figure Presumed mechanism for the adhesion of the OPs to the Fe₃O₄-C18 magnetic nanoparticles     

Catalytic Properties of TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles in Plasma Chemical Treatment

We proposed here a new process coupling dielectric barrier discharge (DBD) plasma with magnetic photocatalytic material nanoparticles for improving yield in DBD degradation of methyl orange (MO). TiO₂ doped Fe₃O₄ (TiO₂/Fe₃O₄) was prepared by the sol-gel method and used as a new type of magnetic photocatalyst in DBD system. It was found that the introduction of TiO₂/Fe₃O₄ in DBD system could effectively make use of the energy generated in DBD process and improve hydroxyl radical contributed by the main surface Fenton reaction, photocatalytic reaction and catalytic decomposition of dissolved ozone. Most part of MO (88%) was degraded during 30 min at peak voltage of 13 kV and TiO₂/Fe₃O₄ load of 100 mg/L, with a rate constant of 0.0731 min^?1 and a degradation yield of 7.23 g/(kW h). The coupled system showed higher degradation efficiency for MO removal.     

Thiol-functionalized Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> microspheres with superparamagnetism and their adsorption properties for Au(III) ion separation

Thiol-functionalized Fe₃O₄/SiO₂ microspheres (Fe₃O₄/SiO₂-SH) with high saturation magnetization (69.3 emu g^–1), superparamagnetism, and good dispersibility have been prepared by an ethylene glycol reduction method in combination with a modified Stöber method. The as-prepared composite magnetic spheres are characterized with fourier transform infrared spectroscopy (FT-IR), zeta potential, X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and superconducting quantum interference magnetometer, and tested in separation of Au(III) ions from aqueous solutions. The data for Au(III) adsorption on Fe₃O₄/SiO₂-SH are analyzed with the Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm models, and the pseudo-first-order, pseudo-second-order, and intraparticle diffusion kinetics models. The adsorption behaviors of Au(III) on Fe₃O₄/SiO₂-SH follow the Langmuir isotherm model, and the adsorption process conforms to the pseudo-second-order kinetic model. The maximum adsorption capacity of Au(III) on Fe₃O₄/SiO₂-SH is 43.7 mg g^–1. Acetate anions play an important role yet Cu(II) ions have little interference in the adsorption of Au(III) on the adsorbent. A satisfactory recovery percentage of 89.5% is acquired by using an eluent with 1 M thiourea and 5% HCl, although thiols have a high affinity to Au(III) ions based on the hard-soft acid-base (HSAB) theory by Pearson.     

Synthesis and Characterization of the Superparamagnetic Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Ag Nanocomposites

The study of superparamagnetic Fe₃O₄/Ag nanocomposites have received great research attention due to their wide range of potential applications in biomedicine. In this report, an easy microemulsion reaction was employed to synthesis Fe₃O₄/Ag nanocomposites with self-aggregated branch like nanostructures. The Fe₃O₄ nanoparticles were initially prepared and subsequently AgNO₃ was reduced as Ag by chemical reduction method. The results showed that the average size of the Fe₃O₄/Ag nanocomposites were in the range of 10 ± 2 nm. These nanoparticles were self-aggregated as a branch like nanostructure. The optical properties of Fe₃O₄ nanoparticles were modified with surface plasmon resonance of Ag nanoparticles. The observed saturation magnetization of superparamagnetic Fe₃O₄/Ag nanocomposites were 40 emu/g.     

Synthesis of hybrid nanoparticles based on magnetic Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles and luminescent CdS nanoparticles

A new approach to the synthesis of hybrid nanoparticles based on magnetic Fe₃O₄ nanoparticles and CdS quantum dots, combining magnetic and luminescence properties, has been suggested. Conditions for preparation of their stable aqueous suspensions have been found, and their optical properties have been studied. Nanocomposites produced at the molar ratio Fe₃O₄: CdS = 5: 1, which exhibited the luminescence properties) and gave stable aqueous suspensions, have turned out to be most promising. The results are evidence that the synthesized nanoparticles can be used for the development of visualizing agents for in vitro biomedical research.     

In situ synthesis of plate-like Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles in porous cellulose films with obvious magnetic anisotropy

Nanocomposite cellulose films with obvious magnetic anisotropy have been prepared by in situ synthesis of plate-like Fe₂O₃ nanoparticles in the cellulose matrix. The influence of the concentrations of FeCl₂ and FeCl₃ solutions on the morphology and particle size of the synthesized Fe₂O₃ nanoparticles as well as on the properties of the composite films has been investigated. The Fe₂O₃ nanoparticles synthesized in the cellulose matrix was γ-Fe₂O₃, and its morphology was plate-like with size about 48 nm and thickness about 9 nm, which was totally different from those reported works. The concentration of FeCl₂ and FeCl₃ solution has little influence on the particle size and morphology of the Fe₂O₃ nanoparticles, while the content of Fe₂O₃ nanoparticles increased with the increase of the concentration of the precursor solution, indicating that porous structured cellulose matrix could modulate the growth of inorganic nanoparticles. The unique morphology of the Fe₂O₃ nanoparticles endowed the composite films with obvious magnetic anisotropy, which would expand the applications of the cellulose based nanomaterials.     

Surface chemistry of nanoscale Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> dispersed in magnetic fluids

The interaction between stabilizers and nanoparticles is one of the important factors to prepare stable magnetic fluids. The magnetic nano-size Fe₃O₄ core with single domain and the average grain size around 8–12 nm were prepared by chemical precipitation method. The O/Fe molar ratio of the particle surface was measured by X-ray photoelectron spectroscopy (XPS). The heat effects of stabilizers adsorption on nanoparticles were measured by solution calorimetry. The excess amount of oxygen was possibly the result of the hydroxygen formed on the surface of the nanoparticles. The heat effects showed that compounds containing carboxyl groups can be adsorbed chemically on magnetite by forming chemical bonds. The other stabilizers involving NH-groups, such as polyethylene-imine, can be adsorbed physically. The exothermic value is about half of the former case. Supported by the National Natural Science Foundation of China (Grant No. 50476039), and Guangdong Provincial Department of Science and Technology (Grant No. 2004A10-703001)     

Nonstoichiometric Zn Ferrite and ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> Composite Spheres: Preparation,Magnetic Properties,and Chromium Removal

Monodisperse and porous nonstoichiometric Zn ferrite can be prepared by a solvothermal method. Such non-Zn ferrite was used to be the precursor for synthesis of ZnFe₂O₄/Fe₂O₃ composite via calcination at 600°C for 3 h in air. X-ray powder diffractometer (XRD) and Energy Dispersive Spectrometer (EDS) proved the nonstoichiometry of Zn ferrite synthesized by solvothermal method and the formation of ZnFe₂O₄/Fe₂O₃ composite via calcination. TEM image showed that non-Zn ferrite spheres with wormlike nanopore structure were made of primary nanocrystals. BET surface area of non-Zn ferrite was much higher than that of ZnFe₂O₄/Fe₂O₃ composite. Saturation magnetization of non-Zn ferrites was significantly higher than that of ZnFe₂O₄/Fe₂O₃ composites. Calcination of non-Zn ferrite resulted in the formation of large amount of non-magnetic Fe₂O₃,which caused a low magnetization of composite. Because of higher BET surface area and higher saturation magnetization, non-Zn ferrite presented better Cr⁶⁺ adsorption property than ZnFe₂O₄/Fe₂O₃ composites.     

Carbon paste electrode modified with Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles and BMI.PF<Subscript>6</Subscript> ionic liquid for determination of estrone by square-wave voltammetry

A carbon paste electrode (CPE) modified with Fe₃O₄ nanoparticles (Fe₃O₄ NP) and the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (IL BMI.PF₆) was employed for the electroanalytical determination of estrone (E1) by square-wave voltammetry (SWV). At the modified electrode, cyclic voltammograms of E1 in B–R buffer (pH 12.0) showed an adsorption-controlled irreversible oxidation peak at around +0.365 V. The anodic current increased by a factor of five times and the peak potential shifted 65 mV to less positive values compared with the unmodified CPE. Under optimized conditions, the calibration curve obtained showed two linear ranges: from 4.0 to 9.0 μmol L^?1 and from 9.0 to 100.0 μmol L^?1. The limits of detection (LOD) and quantification (LOQ) attained were 0.47 and 4.0 μmol L^?1, respectively. The proposed modified electrode was applied to the determination of E1 in pork meat samples. Data provided by the proposed modified electrode were compared with data obtained by UV–vis spectroscopy. The outstanding performance of the electrochemical device indicates that Fe₃O₄ NP and the IL BMI.PF₆ are promising materials for the preparation of chemically modified electrodes for the determination of E1.     

Effective Removal of Nitrotoluene Compounds from Aqueous Solution Using Magnetic-Activated Carbon Nanocomposites (<Emphasis Type="Italic">m</Emphasis>-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@ACCs)

In this study, regular-shaped magnetic-activated carbon nanocomposite (m-Fe₃O₄@ACCs) was synthesized and characterized with X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and the vibrating sample magnetometer (VSM) and was used as adsorbents for the removal of nitrotoluene compounds (NTCs) from water and industrial wastewater. The effective parameters on adsorption process, such as solution pH, shaking speed, contact time, and adsorbent dosage were optimized and the optimum amounts were 7 300 rpm, 10 min, and 1.2 g L^–1, respectively. The contact time and adsorbent dosage are dependent parameters and hence were studied simultaneously. The results showed no significant loss in the adsorption capacity, and the adsorption efficiency of m-Fe₃O₄@ACCs could still be 90% in the 9th cycle. The equilibrium adsorption isotherm followed the Langmuir isotherm model describes the monolayer adsorption of NTCs on m-Fe₃O₄@ACCs, and the maximum adsorption capacities (q_m) for 2-nitrotolouene, 2,6-dinitrotoluene, 2,4-dinitrotoluene, and 3,4-dinitrotoluene were found to be 144.93, 142.86, 166.67, and 153.85 mg g^?l, respectively. The proposed process was successfully applied for the removal of NTCs from tap water and nitration process wastewater.     

Photo-fenton refreshable Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@HCS adsorbent for the elimination of tetracycline hydrochloride

A yolk–shell-structured sphere composed of a superparamagnetic Fe₃O₄ core and a carbon shell (Fe₃O₄@HCS) was etched from Fe₃O₄@SiO₂@carbon by NaOH, which was synthesized through the layer-by-layer coating of Fe₃O₄. This yolk–shell composite has a shell thickness of ca. 27 nm and a high specific surface area of 213.2 m² g^?1. Its performance for the magnetic removal of tetracycline hydrochloride from water was systematically examined. A high equilibrium adsorption capacity of ca. 49.0 mg g^?1 was determined. Moreover, the adsorbent can be regenerated within 10 min through a photo-Fenton reaction. A stable adsorption capacity of 44.3 mg g^?1 with a fluctuation <10% is preserved after 5 consecutive adsorption–degradation cycles, demonstrating its promising application potential in the decontamination of sewage water polluted by antibiotics.     

The design of hybrid materials based on magnetic Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles and luminescent CdS nanoparticles for cell visualization

Hybrid nanoparticles based on Fe₃O₄ and CdS combining magnetic and luminescence properties were synthesized. The possibility of visualization of various cells by 3-mercaptopropylsilane-modified CdS nanoparticles and hybrid nanoparticles based on them using a confocal microscope was demonstrated. The synthesized materials did not show a clear-cut cytotoxicity.