Threshold electrical switching in As45Te55-xInx and As50Te50-xInx glasses

The electrical switching behaviour of As₄₅Te_55-xIn_x (5≤x≤15) and As₅₀Te_50-xIn_x (2.5≤x≤11.5) has been studied over a wide range of compositions. These glasses are found to exhibit threshold switching. The composition dependence of switching voltage (V_t) has been found to exhibit a change in slope and a local minimum at compositions x=10 and 12.5 for As₄₅Te_55-xIn_x and x=7.5 and 10.8 for As₅₀Te_50-xIn_x, respectively. The slope change in V_t verses x and the local minimum have been identified using two network topological effects, namely the rigidity percolation threshold and the chemical threshold. Received: 23 August 2001 / Accepted: 27 August 2001 / Published online: 11 February 2002     

Studies on electrical switching behavior of As-Te-Tl glasses – effect of local structure on switching type and composition dependence of switching voltages

Bulk As-Te-Tl glasses belonging to the As₃₀Te_70-xTl_x (4≤x≤22) and As₄₀Te_60-xTl_x (5≤x≤20) composition tie lines are studied for their I–V characteristics. Unlike other As-Te-III glasses such as As-Te-Al and As-Te-In, which exhibit threshold behavior, the present samples show memory switching. The composition dependence of switching voltages (V_t) of As-Te-Tl glasses is also different from that of As-Te-Al and As-Te-In glasses, and it is found that V_t decreases with the addition of Tl. Both the type of switching exhibited by As-Te-Tl glasses and the composition dependence of V_t, seems to be intimately connected with the nature of bonding of Tl atoms and the resultant structural network. Furthermore, the temperature and thickness dependence of switching voltages of As-Te-Tl glasses suggest an electro thermal mechanism for switching in these samples. PACS 71.55.Jv; 61.43Fs; 61.43.-j; 72.80.Ey; 73.61.Jc     

Interface reactions in [Fe/B]<Subscript>n</Subscript> multilayers: a way to tune from crystalline/amorphous layer sequences to homogeneous amorphous Fe<Subscript>x</Subscript>B<Subscript>100-x</Subscript> films

[Fe/B]_{n ≥2} multilayers were prepared by thermal evaporation, ion-beam sputtering and laser ablation. By applying in situ electron spectroscopies (UPS, XPS) and monitoring the electrical resistance during layer growth, evidence could be provided for the occurrence of interface reactions within the range of studied deposition temperatures (77 K ≤T ≤300 K). These reactions result in amorphous Fe_xB_100-x phases, which are spatially restricted to a width of less than 3 nm at the original interface. The amorphicity of the reacted interlayers was unequivocally proven by additional high-resolution electron microscopy (HRTEM) and their characteristically changed magnetic properties. Due to the well-defined width of the interface reaction, homogeneous amorphous Fe_xB_100-x films can be obtained by reducing the individual Fe and B layer thicknesses to below the above reaction depth, while for larger thicknesses layer sequences of the crystalline/amorphous/crystalline type will result. Received: 30 January 2002 / Accepted: 31 January 2002 / Published online: 10 September 2002 RID="*" ID="*"Corresponding author. Fax: +49-731/502-2963, E-mail: hans-gerd.boyen@physik.uni-ulm.de     

Evidence of an intermediate phase in ternary Ge<Subscript>7</Subscript>Se<Subscript>93-x</Subscript>Sb<Subscript>x</Subscript> glasses

The compositional dependence of thermal properties, such as glass transition temperature (T_g), non-reversing enthalpy change (ΔH_NR) and the specific heat capacity change (ΔC_p) of melt quenched Ge₇Se_93-xSb_x (21 ≤ x ≤ 31) glasses, has been studied using alternating differential scanning calorimetry (ADSC) which is analogous to modulated differential scanning calorimetry (MDSC). The glass transition temperature, T_g, which is a measure of global connectivity of the glass, has been found to increase with the addition of Sb. In addition, a change in slope has been observed in the composition dependence of T_g at an average coordination 〈r〉 = 2.40. The experimentally observed compositional variation of glass transition temperature, has been compared with the theoretical predictions from the stochastic agglomeration theory (SAT) and has been found to be consistent. Further, a narrow thermally reversing window is seen in the compositional variation of the relaxation enthalpy (ΔH_NR), which is centered around 〈r〉 = 2.40. The change in specific heat capacity (ΔC_p) at T_g is also found to exhibit a distinct minima at 〈r〉 = 2.40, suggesting that the structural rearrangements for the liquid in the glass transition region are minimized around 〈r〉 = 2.4.     

Structure,transport and field-emission properties of compound nanotubes: CN<Subscript>x</Subscript> vs. BNC<Subscript>x</Subscript> (<Emphasis Type="Italic">x</Emphasis><0.1)

Transport and field-emission properties of as-synthesized CN_x and BNC_x (x<0.1) multi-walled nanotubes were compared in detail. Individual ropes made of these nanotubes and macrofilms of those were tested. Before measurements, the nanotubes were thoroughly characterized using high-resolution and energy-filtered electron microscopy, electron diffraction and electron-energy-loss spectroscopy. Individual ropes composed of dozens of CN_x nanotubes displayed well-defined metallic behavior and low resistivities of ∼10–100 kΩ or less at room temperature, whereas those made of BNC_x nanotubes exhibited semiconducting properties and high resistivities of ∼50–300 MΩ. Both types of ropes revealed good field-emission properties with emitting currents per rope reaching ∼4 μA(CN_x) and ∼2 μA (BNC_x), albeit the latter ropes se- verely deteriorated during the field emission. Macrofilms made of randomly oriented CN_x or BNC_x nanotubes displayed low and similar turn-on fields of ∼2–3 V/μm. 3 mA/cm² (BNC_x) and 5.5 mA/cm² (CN_x) current densities were reached at 5.5 V/μm macroscopic fields. At a current density of 0.2–0.4 mA/cm² both types of compound nanotubes exhibited equally good emission stability over tens of minutes; by contrast, on increasing the current density to 0.2–0.4 A/cm², only CN_x films continued to emit steadily, while the field emission from BNC_x nanotube films was prone to fast degradation within several tens of seconds, likely due to arcing and/or resistive heating. Received: 29 October 2002 / Accepted: 1 November 2002 / Published online: 10 March 2003 RID="*" ID="*"Corresponding author. Fax: +81-298/51-6280, E-mail: golberg.dmitri@nims.go.jp     

Structural and optical characterization of polycrystalline CdSe<Subscript>x</Subscript>Te<Subscript>1-x</Subscript> thin films

Solid solutions of CdSe_xTe_1-x (0.7x1) were synthesized by vacuum fusion of stoichiometric amounts of CdSe and CdTe constituents in a silica tube. X-ray and electron microscope diffractometry techniques revealed that the CdSe_xTe_1-x thin films were polycrystalline with a hexagonal structure. The variation of lattice constants with composition was found to obey Vegards law. The compositional dependence of the optical constants, the refractive index n and the absorption index k, of the films was determined in the spectral range of 400–2000 nm. The dispersion of the refractive index of the films could be described using the Wemple–DiDomenico single oscillator model. Changes of the dispersion parameters were also studied as a function of the mole fraction x. A plot representing ²=f(h) showed that the CdSe_xTe_1-x thin films of different compositions have two direct transitions corresponding to the energy gaps E_g and E_g+. The variation in either E_g or E_g+ with x indicates that this system belongs to the amalgamation type. The variation follows a quadratic dependence and the bowing parameters were found to be 0.4 and 0.5 eV, respectively. PACS 78.20.-e; 81.15.-z     

Structural and optical properties of Bi<Subscript>3.25</Subscript>La<Subscript>0.75</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> ferroelectric thin films prepared by chemical solution methods

Ferroelectric Bi_3.25La_0.75Ti₃O₁₂ (BLT) thin films have been grown on Pt/Ti/SiO₂/Si substrates by chemical solution methods. X-ray diffraction analysis shows that BLT thin films are polycrystalline with (171)-preferential orientation. Atomic force microscopy investigation shows that they have large grains about 120 nm in size. A Pt/BLT/Pt capacitor has been fabricated and showed excellent ferroelectricity, with a remnant polarization and coercive field of 24 μC/cm² and 116 kV/cm, respectively. The capacitor shows no polarization fatigue up to 10⁹ switching cycles. The optical constants (n,k) of the BLT thin films in the wavelength range 0.35–1.7 μm were obtained by spectroscopic ellipsometry measurements, and the band-gap energy was found to be about 3.25 eV. Received: 16 October 2001 / Accepted: 6 January 2002 / Published online: 3 June 2002 RID="*" ID="*"Corresponding author. Fax: +86-21/65830-734, E-mail: gswang@mail.sitp.ac.cn     

Electrical properties of a-Ge<Subscript>x</Subscript>Se<Subscript>100-<Emphasis Type="Italic">x</Emphasis></Subscript>

In general, the conductivity in chalcogenide glasses at higher temperatures is dominated by band conduction (DC conduction). But, at lower temperatures, hopping conduction dominates over band conduction. A study at lower temperature can, eventually, provide useful information about the conduction mechanism and the defect states in the material. Therefore, the study of electrical properties of Ge_xSe_100-x in the lower temperature region (room temperature) is interesting. Temperature and frequency dependence of Ge_xSe_{100-x (x} = 15, 20 and 25) have been studied over different range of temperatures and frequencies. An agreement between experimental and theoretical results suggested that the behaviour of germanium selenium system (Ge_xSe_100-x ) have been successfully explained by correlated barrier hopping (CBH) model.     

Studies on Structural,Morphological and Optical Properties of Chemically Deposited CdS<Subscript>1-x</Subscript>Se<Subscript>x</Subscript> Thin Films

The thin films of CdS_1-xSe_x were successfully deposited over glass substrates by chemical bath deposition technique. Cadmium acetate, thiourea and sodium selenosulfate were used as source materials for Cd²⁺, S^2? and Se^2? ions, while 2-mercaptoethanol was used as capping agent. The various deposition conditions such as precursor concentration, deposition temperature, pH and deposition time were optimized for the deposition of CdS_1-xSe_x thin films of good quality and the films were annealed at 200° and 300 °C. The structural, morphological, chemical and optical properties were examined by various characterization techniques and discussed in detail. The optical band gap of CdS_1-xSe_x thin film samples were estimated and found in the range from 2.11 to 1.79 eV for as-deposited and annealed thin films.     

Temperature Dependence of the Transmission Spectra of Silicate Glasses Containing CdS<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Se<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> Semiconducting Nanocrystals

The transmission spectra of silicate glasses containing CdS_{1 − x} Se _x semiconducting nanocrystals of various sizes are investigated in the temperature range 20–300°C. It is shown that for explaining optical properties of these materials, not only the nanocrystal sizes, but also the structural changes occurring in nanocrystals during their formation must be taken into account.     

Photoacoustic spectroscopy of thin films of As<Subscript>2</Subscript>S<Subscript>3</Subscript>, As<Subscript>2</Subscript>Se<Subscript>3</Subscript> and GeSe<Subscript>2</Subscript>

Photoacoustic spectroscopy (PAS) is one of the important branches of spectroscopy, which enables one to detect light-induced heat production following the absorption of pulsed radiation by the sample. As₂S₃, As₂Se₃ and GeSe₂ exhibit a wide variety of photo-induced phenomena that enable them to be used as optical imaging or storage medium and various electronic devices, including electro-optic information storage devices and optical mass memories. Therefore, accurate measurement of thermal properties of semiconducting films is necessary to study the memory density. The thermal conductivity of thin films of As₂S₃ (thickness 100 μm and 80 μm), As₂Se₃ (thickness 100 μm and 80 μm) and GeSe₂ (thickness 120 μm and 100 μm) has been measured using PAS technique. Our result shows that the thermal conductivity of thicker films is larger than the thinner films. This can be explained by the thermal resistance effect between the film and the surface of the substrate.      

Role of Ge incorporation in the physical and dielectric properties of Se<Subscript>75</Subscript>Te<Subscript>25</Subscript> and Se<Subscript>85</Subscript>Te<Subscript>15</Subscript> glassy alloys

The effect of Ge additive on the physical and dielectric properties of Se₇₅Te₂₅ and Se₈₅Te₁₅ glassy alloys has been investigated. It is inferred that on adding Ge, the physical properties i.e., average coordination number, average number of constraints and average heat of atomization increase but lone pair electrons, fraction of floppy modes, electronegativity, degree of crosslinking and deviation of stoichiometry (R) decrease. The effect of Ge doping on the dielectric properties of the bulk Se₇₅Te₂₅ and Se₈₅Te₁₅ glassy alloys has also been studied in the temperature range 300–350 K for different frequencies (1 kHz–5 MHz). It is found that, with doping, the dielectric constant ε^′ and dielectric loss ε^″ increase with increase in temperature and decrease with increase in frequency. The role of the third element Ge, as an impurity in the two pure binary Se₇₅Te₂₅ and Se₈₅Te₁₅ glassy alloys has been discussed in terms of the nature of covalent bonding and electronegativity difference between the elements used in making the aforesaid glassy systems.     

Fundamental band edge optical absorption in Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript>

Spectra of optical absorption in Bi_0.5Sb_1.5Te₃ films grown on mica and KBr substrates have been investigated for T = 145 and 300 K. The data obtained have been analyzed together with the data of investigations on the fundamental absorption edge for Bi₂Te₃ available in the scientific literature. It has been revealed that the interband absorption spectra for both Bi_0.5Sb_1.5Te₃ and Bi₂Te₃ represent a superposition of two components corresponding to direct and indirect allowed optical transitions. In this case, the least energy gap separating the valence band and the conduction band is direct for Bi_2−xSb_xTe₃ (x ≤ 1.5, T = 300 K). For Bi_0.5Sb_1.5Te₃ the temperature variation rates have been estimated for the thresholds of direct and indirect interband transitions. It has been shown that this solid solution is direct gap solution at T ≥ 145 K. Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 7, pp. 50–52, July, 2008.     

Influence of different precursor surface layers on Cu(In<Subscript>1-x</Subscript>Ga<Subscript>x</Subscript>)Se<Subscript>2</Subscript> thin film solar cells

The properties of Cu(In_1-xGa_x)Se₂ (CIGS) thin films obtained by selenization of the precursors with different surface layers have been studied, and photovoltaic devices based on the absorbers were measured and analyzed. The devices constructed by the absorbers obtained by selenization of the precursors with CuGa-rich surface layers are improved, compared with those with In-rich surface layers. Through XRD, SEM, SIMS, illuminated J–V, QE and Raman spectra measurements, it was found that the increased Ga contents within the surface region of films and the graded Ga distribution can be realized in the selenized thin films fabricated by the precursors with the CuGa-rich surface layer. Consequently, the performances of the photovoltaic devices based on these thin films are further improved. PACS 61.72.Ss; 87.64.Jt; 68.60.Bs; 81.15.Cd; 84.60.Jt     

Intensely emitting CdTe nanocrystals retained initial photoluminescence efficiency in sol–gel derived Si<Subscript>1-x</Subscript>Zr<Subscript>x</Subscript>O<Subscript>2</Subscript> glass

Emitting CdTe nanocrystals (NCs) were embedded in pure glass matrices (Si_1-xZr_xO₂, x≤0.15) using a controlled sol–gel method, where the pre-hydrolyzed condition, the molar ratio of Zr/Si, the gelation time, the pH, and the amount of alcohol were judiciously optimized considering the surface condition of the NCs and the mechanism of the glass formation. As a result, the prepared glass phosphor exhibited high photoluminescence efficiencies (40% for green and 60% for red when Zr/Si was 5–10%) by retaining their initial values as in CdTe colloidal solution. To our knowledge, these values are the highest among those ever obtained for any solid matrices containing NCs. Because of the existence of Zr, the prepared glasses exhibit much better resistance against the ambient atmosphere, heat-treatment, and boiling water compared with pure silica glass (x=0) or the glass prepared from our other methods using a silane coupling agent. Thus, the obtained glass is promising for applications such as optical devices. PACS 78.67.Bf; 78.55.Qr; 78.55.Et     

N+BF<Subscript>2</Subscript> and N+C+BF<Subscript>2</Subscript> high-dose co-implantation in silicon

Nitrogen and boron BF₂, and nitrogen, carbon, and boron BF₂ high-dose (6×10¹⁶–3×10¹⁷ cm^-2) co-implantation were performed at energies of about 21–77 keV. Subsequent high-temperature annealing processes (600, 850, and 1200 °C) lead to the formation of three and two surface layers respectively. The outer layer mainly consists of polycrystalline silicon and some amorphous material and Si₃N₄ inclusions. The inner layer is highly defective crystalline silicon, with some inclusions of Si₃N₄ too. In the N+B-implanted sample the intermediate layer is amorphous. Co-implantation of boron with nitrogen and with nitrogen and carbon prevents the excessive diffusivity of B and leads to a lattice-parameter reduction of 0.7–1.0%. Received: 10 January 2002 / Accepted: 30 May 2002 / Published online: 4 November 2002 RID="*" ID="*"Corresponding author. Fax: +34-91/3974895; E-mail: Lucia.Barbadillo@uam.es     

Synthesis and photoluminescence of aligned SiO<Subscript>x</Subscript> nanowire arrays

Aligned SiO_x nanowire arrays standing on a Si substrate were successfully synthesized using a simple method by heating a single-crystalline Si slice covered with SiO₂ nanoparticles at 1000 °C in a flowing Ar atmosphere. The SiO_x nanowire arrays were characterized by scanning electron microscopy and transmission electron microscopy. The SiO_x nanowires become progressively thinner from bottom to top. The formation process of the SiO_x nanowire arrays is closely related to a vapor–solid mechanism. Room-temperature photoluminescence measurements under excitation at 260 nm showed that the SiO_x nanowire arrays had a strong blue–green emission at 500 nm (about 2.5 eV), which may be related to oxygen defects. Received: 29 April 2002 / Accepted: 30 April 2002 / Published online: 10 September 2002 RID="*" ID="*"Corresponding author. Fax: +86-551-559-1434, E-mail: gwmeng@mail.issp.ac.cn     

Insulator-metal transition shift related to magnetic polarons in La<Subscript>0.67-x</Subscript>Y<Subscript>x</Subscript>Ca<Subscript>0.33</Subscript>MnO<Subscript>3</Subscript>

The magnetic transport properties have been measured for La_0.67-xY_xCa_0.33MnO₃ ( 0 ⩽ x ⩽ 0.14) system. It was found that the transition temperature T _p almost linearly moves to higher temperature as H increases. Electron spin resonance confirms that above T _p , there exist ferromagnetic clusters. From the magnetic polaron point of view, the shift of T _p vs. H was understood, and it was estimated that the size of the magnetic polaron is of 9.7 ∼ 15.4 ? which is consistent with the magnetic correlation length revealed by the small-angle neutron-scattering technique. The transport properties at temperatures higher than T _p conform to the variable-range hopping mechanism. Received 27 August 2002 / Received in final form 2 December 2002 Published online 14 March 2003     

Magnetic and electrical investigations of Fe<Subscript>85-x</Subscript>Co<Subscript>x</Subscript>B<Subscript>15</Subscript> metallic glasses

The magnetic and electrical properties of metallic glasses with the general formula Fe_85-xCo_xB₁₅ were investigated over a large temperature range to study their concentration-dependent physical parameters. All of the samples investigated (x=17,21,30, and 40) were soft ferromagnets with coercive fields H_c1 Oe and high Curie temperatures slightly above 1200 K. The temperature-dependent magnetization behaved irregularly, and exhibited hysteresis during heating and subsequent cooling through the Curie temperature. The variation of the magnetization with temperature demonstrates that one or more phase transformations (crystallization) occurred in the course of the heating. The electrical resistivities exhibited positive temperature coefficients and minima at temperatures below 50 K. We did not observe a nonmonotonic variation of the magnetic and electrical properties with a monotonic change of the Fe_85-xCo_xB₁₅ composition that would correlate with the earlier proposed formation of strong nanoclusters in the vicinity of particular stoichiometrically close Fe:Co ratios. The good soft magnetic characteristics make the Fe_85-xCo_xB₁₅ metal glasses promising candidates for engineering materials in inductive applications. PACS 71.23.Cq; 75.75.+a     

An evidence for a microscopic phase separation in AsSeAg glasses revealed by thermal and structural investigations

Alternating Differential Scanning Calorimetric (ADSC) studies show that Se rich As₂₀Se_80-xAg_x (0 ≤ x ≤ 15) glasses exhibit two endothermic glass transitions and two exothermic crystallization peaks; the observed thermal behavior has been understood on the basis that As₂₀Se_80-xAg_x glasses are microscopically phase separated, containing Ag₂Se phases embedded in an As-Se backbone. With increasing silver concentration, the Ag₂Se phase percolates in the As-Se matrix, with a well-defined percolation threshold at x = 8. A signature of this percolation transition is shown up in the thermal behavior, as sudden jumps in the composition dependence of non-reversing enthalpy, ΔH_nr obtained at the second glass transition reaction. Scanning Electron Microscopic (SEM) studies also confirm the microscopic phase separation in these glasses. The super-ionic conduction observed earlier in these glasses at higher silver proportions, is likely to be associated with the silver phase percolation.