X-ray fluorescence analysis of rare earth elements in rocks using low dilution glass beads.

Major and trace elements (Na, Mg, Al, Si, P, K, Ca, Ti, Mn, Fe, Rb, Sr, Y, Zr, La, Ce, Pr, Nd, Sm, Gd, Dy, Th and U) in igneous rocks were assayed with fused lithium borate glass beads using X-ray fluorescence spectrometry. Low dilution glass beads, which had a 1:1 sample-to-flux ratio, were prepared for determination of rare earth elements. Complete vitrification of 1:1 mixture required heating twice at 1200 degrees C with agitation. Extra pure reagents containing determinants were used for calibrating standards instead of the rock standard. The calibration curves of the 23 elements showed good linearity. Furthermore, the lower limits of detection corresponding to three times the standard deviation for blank measurements were 26 mass ppm for Na2O, 6.7 for MgO, 4.5 for Al2O3, 4.5 for SiO2, 18 for P2O5, 1.1 for K2O, 4.0 for CaO, 3.9 for TiO2, 1.6 for MnO, 0.8 for Fe2O3, 0.5 for Rb, 0.2 for Sr, 0.4 for Y, 0.5 for Zr, 3.3 for La, 6.5 for Ce, 2.7 for Pr, 2.1 for Nd, 1.7 for Sm, 0.7 for Gd, 2.7 for Dy, 0.5 for Th, and 0.6 for U. Using the present method, we determined the contents of these 23 elements in four rhyolitic and granitic rocks from Japan.     

电感耦合等离子体质谱法快速测定苦荞茶中铜、铅、镉、钴、镍

建立了用硝酸-高氯酸消解样品,电感耦合等离子体质谱法(ICP-MS)测定苦荞茶中铜、铅、镉、钴、镍的方法.方法具有灵敏度高、检出限低、精密度好、基体干扰少、准确可靠、快捷、简便的特点.各元素方法检出限(3SD,μg/L)分别为:铜0.009、铅0.023、镉0.015、钴0.022、镍0.035;方法精密度(RSD,n=12)分别为:铜2.5%～3.0%、铅2.1%～2.3%、镉3.0%～3.8%、钴2.5%～2.6%、镍1.5%～1.9%;各元素加标回收率分别为:铜95.0%～105.0%、铅95.0%～105.0%、镉98.0%～105.0%、钴95.0%～105.0%、镍95.0%～105.0%.在线用铑作为内标95.0%～105.0%.方法经国家一级标准物质验证,测定值与标准值吻合.应用于实际样品测定,结果满意.     

Quantitative determination of aflatoxin B1-oxime by column liquid chromatography with ultraviolet detection.

Liquid chromatography was used for the quantification of aflatoxin B1-oxime (AFB1-oxime). The yield of AFB1-oxime in the reaction mixture was 89%, while after purification on silica gel it was 72%. LC analysis of the reaction mixture after silica gel fractionation revealed a retention time of 0.84 min for AFB1-oxime, 8.42 min for AFB1, 1.21 min for unknown 1 and 1.61 min for unknown 2. UV-visible analysis of the reaction mixture after silica gel fractionation showed a lambda(max) of 269 and 361 nm for AFB1-oxime, 263 and 360 nm for AFB1, 273 nm for unknown 1 and 275 nm for unknown 2. Excitation and emission wavelengths were found to be 269 and 368/438 nm for AFB1-oxime, 359/424 nm for AFB1, 270 and 367/450 nm for unknown 1 and 273 and 416/447 nm for unknown 2. The method may find versatile application in monitoring reactions for the preparation of oximes of various analytes for the synthesis of their immunogens.     

Determination of fumonisins B1 and B2 in corn and corn flakes by liquid chromatography with immunoaffinity column cleanup: collaborative study.

A liquid chromatographic (LC) method for the determination of fumonisins B1 (FB1) and B2 (FB2) in corn and corn flakes was collaboratively studied by 23 laboratories, which analyzed 5 blind duplicate pairs of each matrix to establish the accuracy, repeatability, and reproducibility characteristics of the method. Fumonisin levels in the corn ranged from <0.05 (blank) to 1.41 microg/g for FB1 and from <0.05 to 0.56 microg/g for FB2, whereas in the corn flakes they ranged from <0.05 to 1.05 microg/g for FB1 and from <0.05 to 0.46 microg/g for FB2. The method involved double extraction with acetonitrile-methanol-water (25 + 25 + 50), cleanup through an immunoaffinity column, and LC determination of the fumonisins after derivatization with o-phthaldialdehyde. Relative standard deviations for the within-laboratory repeatability (RSDr) of the corn analyses ranged from 19 to 24% for FB1 and from 19 to 27% for FB2; for the corn flakes analyses, RSDr ranged from 9 to 21 % for FB1 and from 8 to 22% for FB2. Relative standard deviations for the between-laboratories reproducibility (RSDR) of the corn analyses ranged from 22 to 28% for FB1 and from 22 to 30% for the FB2; for corn flakes analyses, RSDR ranged from 27 to 32% for FB1 and from 26 to 35% for FB2. Mean recoveries of FB1 and FB2 from corn spiked with FB1 at 0.80 microg/g and with FB2 at 0.40 microg/g were 76 and 72%, respectively; for corn flakes spiked at the same levels recoveries were 110 and 97% for FB1 and FB2, respectively. HORRAT ratios for the analyses of corn ranged from 1.44 to 1.53 for FB1 and from 0.96 to 1.48 for FB2, whereas for corn flakes they ranged from 1.60 to 1.82 for FB1 and from 1.39 to 1.68 for FB2.     

Traditional medicine in Syria: folk medicine in Aleppo governorate

The use of Traditional Arabic Medicine (TAM) for various diseases has been popular but scarcely studied in Syria. In the present study, we carried out ethnobotanical and ethnopharmacological research on the plants traditionally used to cure various diseases in northern Syria. The information was collected from the city and villages of the Aleppo governorate "Mohaafazah" in the north of Syria, collecting data directly on the basis of a detailed survey of inhabitants and herbalists. In this survey, we found that hundreds of plant species are still in use in TAM for the treatment of various diseases. We selected the most common 100 species, used in the treatment of more than 25 diseases. Among these plants, 53 are used for treating gastrointestinal disorders, 38 for respiratory system diseases, including asthma, bronchitis and cough, 34 for skin diseases, 21 for diabetes, 17 for kidney and urinary disorders, 16 for cardiac disorders, 14 for infertility and sexual impotency, 13 for treating liver diseases, 13 for several types of cancer, 9 for enhancing breast milk excretion, 8 for weight loss, 5 for reducing cholesterol, and three for weight gain. Plants were collected and identified: scientific Latin names, local names, the used parts of the plant, the herbal preparations and the local medical uses are described. Scientific literature concerning the activity of the investigated species is also reported and discussed according to their traditional uses.     

Pharmacokinetic applications of capillary electrophoresis

This review briefly discusses the use of capillary electrophoretic (CE) methods for the investigations of different aspects of pharmacokinetics. In most investigations, CE was the method of choice because of its unique features, including high resolving power for chiral or metabolite separation, small sample volume for pediatric pharmacokinetics or for cell-based investigations, in situ microdialysis sampling for rapid eliminations, low UV wavelength detection for nonderivatized analytes, fast and simplified sample processing for existing methods that require tedious sample preparation, or as a second method for verifications. Moreover, instrumental aspects of CE-based assays for pharmacokinetic studies, such as different modes of CE methods for analyzing biological samples, sample stacking for increasing detection sensitivity, and coupling techniques with microdialysis and mass spectrometry, are also discussed in this review. Furthermore, the advantages and limitations of CE methods as well as the future outlook for pharmacokinetic studies are summarized.     

A pilot study for the preparation of a new Reference Material based on antarctic krill

The preparation of new Certified Reference Materials (CRMs) of antarctic matrices forms the backbone of an ongoing project in the framework of the Italian National Program for Antarctic Research. The first CRM of this kind (MURST-ISS-A1 Antarctic Marine Sediment) is already available. The second phase focuses on the certification of antarctic krill, a small shrimp extremely abundant in the Southern Ocean. The total mass of krill available for this purpose is approximately 44 kg and results from the combination of three different catches (Ross Sea, Marguerite Bay and Livingston Island, respectively). The quantification of the following elements in the raw mass appears to be affordable by current analytical techniques, values being in the range of (in μg/g) 0.11–0.30 for As, 0.03–0.12 for Cd, 0.06–0.23 for Cr, 6.1–21 for Cu, 5.7–7.6 for Fe, 0.005–0.008 for Hg, 0.7–1.2 for Mn, 0.013– 0.077 for Ni, 0.04–0.57 for Pb and 12–16 for Zn. On the other hand, the average values ascertained in freeze-dried krill are as a rule one order of magnitude higher, i.e., (in μg/g), 3.2 for As, 0.6 for Cd, 1.8 for Cr, 75 for Cu, 61 for Fe, 0.025 for Hg, 4.6 for Mn, 0.7 for Ni, 2.1 for Pb and 81 for Zn. Information on the pretreatment of krill and details on the planned certification campaign are also given. Received: 10 June 1997 / Revised: 24 September 1997 / Accepted: 28 September 1997     

Normal Coordinate Analysis for Polymer Systems: Capabilities and New Opportunities

Normal coordinate analysis is an important tool in studying the structure, dynamics, and physical properties of polymer systems. In this article the capabilities of normal coordinate analysis (NCA) are explored in some detail. The use of the eigenvalues and eigenvectors from NCA is catalogued for a wide variety of purposes: for assigning or interpreting polymer spectra, for structural determination, for constructing force fields, for computing heat capacity and other thermodynamic properties, and for computing other physical properties. Examples are given for crystals, melts, and amorphous systems. Also described are methods for characterizing the normal mode vectors that are especially useful for larger systems, in which a large amount of data must be analyzed or where visualization or animation fails. Finally, a recently developed method for eliminating negative eigenvalues in systems with tens of thousands of atoms, trajectory averaging, is presented. Also described are several advances in numerical linear algebra for speeding up the diagonalization phase and for computing physical properties without requiring full diagonalization of the Hessian matrix.     

Method validation for determination of 13 elements in honey samples by ICP-MS

A method for simultaneous ICP-MS determination of 13 elements in three types of honey from Poland is described. The method was validated, and the uncertainty budget was set up. The results obtained for the relative expanded uncertainties U _rel (k = 2) were 15.1% for Al, 18.6% for B, 18.8% for Ba, 7.9% for Ca, 24.4% for Cd, 7.24% for Cu, 7.9% for K, 4.8% for Mg, 8.3% for Mn, 12.7% for Na, 14.9% for Ni, 12.5% for Pb and 13.4% for Zn. Traceability of the measurement results was established based on the use of the corn flour CRM INCT-CF-3 and the apple leaves CRM SRM 1515 and by analyzing spiked samples. Recovery rates between 94% (Zn) and 107% (Na) were found. The detection limits of all elements studied showed the suitability of the procedure for routine analyses. Summarizing it can be concluded that the described analytical procedures to measure the mass fractions of 13 elements in honey samples with established traceability and evaluated uncertainty allow to obtain reliable and internationally comparable results.     

Concentrations of 239,240Pu and 241Am of marine products in coastal waters of Ibaraki

More than 200 samples of marine products have been collected and analyzed for plutonium and almost 100 samples for americium around Hitachi, Tokai and Oarai in the pacific coast of Ibaraki prefecture. The data have shown that the concentration factor (CF) values for plutonium were 330 for bivalve, 770 for abalone (muscle) and 610 for brown algae. For americium, the CF was calculated as 2400 for bivalve, 1000 for abalone (muscle) and 420 for brown algae.     

Heats of formation and kinetics of decomposition of nitroalkanes

Heats of formation of solid, liquid, and gaseous nitroalkanes have been shown mostly to obey group additivity. Group values have been obtained for carbon atoms attached to one, two, and three nitro groups. The heat of formation of 1,1,1,3,5,5,5,-heptanitropentane, either solid or liquid, cannot be fitted to the scheme, even allowing for gauche effects. The differences between observed and estimated values for 1,1,1-fluorodinitroalkanes and 1,2-dinitroethane are larger than expected and should be further investigated. Activation energies have been calculated for decomposition by five-center elimination of HONO from mononitro- and dinitroalkanes using thermochemistry and estimated activation energies for the reverse reactions. The key data for these estimates were previously reported activation energies for the decomposition of nitroethane and 1,2-dinitropropane. The calculations also gave values for the heats of formation (in kcal/mole) of nitroethylene 12.4, and 1-nitropropylene 5.6, and 2-nitropropylene 1.6. Activation energies were calculated for the competing unimolecular reaction, C? N bond fission, from thermochemistry and previously reported activation energies for the decomposition of 1,1- and 2,2-dinitropropane. Comparison of Arrhenius parameters for the two competing processes, namely, HONO and C? N bond fission, shows that, for the geminate dinitroethanes and dinitropropanes, C? N bond fission is faster about 370°K and, for the mononitroalkanes and for all the mononitroalkanes and dinitroalkanes, C? N bond fission is faster above 770°K.     

New cleft-like molecules and macrocycles from phosphonate substituted spirobisindanol

We have synthetized medium-sized cyclophanes and macrocycles containing phosphonic groups, directly linked to the aromatic rings of the phanes or as pendant arms,for use as specific receptors for the selective complexation of neutral guests or for complexing lanthanides, as luminescent sensors and for diagnostic bioassays in medicine.Furthermore, because it would be of great interest for biochemistry as well as for pharmacological studies to dispose of preorganized rigid chiral hosts for biorelevant molecules we designed inter alia, some new chiral macrocycles capable of a triple binding mode and we used them for constructing macrocycles that could also be of interest for chiral recognition and chiral separations. Thus, in this paper we shall review the salient aspects of some macrocycles synthetized in our laboratory, all possessing the phosphonate moiety and a spirobisindanol scaffold and able to act as complexing agents for cations and organic substrates. In particular, we shall describe their NMR characterization, their stereochemistry in solution and in the solid state, and their use as chiral receptors for biorelevant molecules. Chiral HPLC resolution of some of them is also reported.     

Dibenzomethanopentacene-Based Polymers of Intrinsic Microporosity for Use in Gas-Separation Membranes

Dibenzomethanopentacene (DBMP) is shown to be a useful structural component for making Polymers of Intrinsic Microporosity (PIMs) with promise for making efficient membranes for gas separations. DBMP-based monomers for PIMs are readily prepared using a Diels–Alder reaction between 2,3-dimethoxyanthracene and norbornadiene as the key synthetic step. Compared to date for the archetypal PIM-1, the incorporation of DBMP simultaneously enhances both gas permeability and the ideal selectivity for one gas over another. Hence, both ideal and mixed gas permeability data for DBMP-rich co-polymers and an amidoxime modified PIM are close to the current Robeson upper bounds, which define the state-of-the-art for the trade-off between permeability and selectivity, for several important gas pairs. Furthermore, long-term studies (over ≈3 years) reveal that the reduction in gas permeabilities on ageing is less for DBMP-containing PIMs relative to that for other high performing PIMs, which is an attractive property for the fabrication of membranes for efficient gas separations.     

Theoretical analysis of resonant raman scattering: Simulations of lineshapes and excitation profiles

The steady-state response of a three-level system in the presence of a strong laser field is described with the density operator formalism, in order to derive an analytical expression for the intensity of resonance Raman scattering. The Liouville equation for the density operator is written in quantum form for both the molecular system and the radiation field, making use of the dipole and rotating-wave approximations for the matter-radiation interaction, and of the Markov approximation for the molecular decays. The equation is solved exactly for the laser field, and in perturbative way for the generated field. The results account for power broadening of the generated line. Rabi intensity-dip of the generated signal, and for the excitation profiles in the Franck-Condom approximation.     

Successive non-suppressed ion chromatography of common cations and anions using dual columns with single eluent

A successive non-suppressed ion chromatography (IC) system for the determination of common cations (Na+, K+, Mg2+, Ca2+) and anions (Cl-, Br-, NO3-, SO4(2-)) was developed, using two separation columns and a single eluent. 5-Sulfoisophthalic acid eluent was very suitable for such separations with a commercially available cation-exchange column for the mono- and di-valent cations and with an ODS column coated with cetyltrimethylammonium for the anions. Both cations and anions were detected with conductimetrically high sensitivity without any suppressor. After injecting an aliquot of sample solution, the solvent front from the cation-exchange column, including most of the anionic species, was firstly accumulated into the additional 2 ml accumulation loop for 60 s, while the cation IC was performed. Subsequently, the accumulated fraction was introduced into the anion-exchange column and chromatographed. Relative standard deviations (RSDs) of retention times and conductimetric area responses for common cations were within 6% and within 4%, respectively. The linear relationships between molar concentration and detector response ranged from 0.01 to 1.00 mM with r2 of 0.9994 for Na+, 0.9992 for K+, 0.9993 for Mg2+, and 0.9988 for Ca2+. The successive anion IC through the accumulating process was also quantitative, with 95% recovery or over for each analyte. The linear ranges were between 0.01 and 1.00 mM with r2 of 0.9996 for Cl-, 0.9997 for Br-, 0.9993 for NO3-, and 0.9984 for SO4(2-). The method was applied to the determination of common cations and anions in several mineral waters and a hot spring water.     

Simultaneous determination of rhenium,osmium and iridium in meteoritic samples by neutron activation analysis using simple and effective radiochemical procedures

Simple and effective procedures for the determination of Re, Os and Ir by radiochemical neutron activation analysis are presented. Those elements are separated individually by distillation (for Os) and anion exchange techniques (for Re and Ir) for a single specimen. Reproducibilities of the data obtained by the present procedures are evaluated by replicate analyses of the Allende meteorite sample, and are deduced to be 3% for Re, 6% for Os and 4% for Ir (1). Detection limits for the present procedures are calculated to be 1 ppb for Re, 20 ppb for Os and 5 ppb for Ir. These procedures were applied to Antarctic meteorites and proved to work very effectively for the determination of trace Re, Os and Ir in chondrite meteorites.     

Kinetic and thermodynamic stability of acenes: Theoretical study of nucleophilic and electrophilic addition

To understand the reactivity of acenes, particularly pentacene, the addition of HCl and water to acenes was studied for the benzene-nonacene series at the B3LYP/6-31G(d) level of theory. Surprisingly, the reactivity of the acenes increases along the series up to hexacene and remains constant from hexacene and above due to the biradical character of the ground state of higher acenes. While the exothermicity of HCl and water additions are very similar, the activation barriers for HCl and water additions differ by a constant factor of ca. 27 kcal/mol. The barrier for the addition of HCl varies from 44 kcal/mol for benzene to 16-18 kcal/mol for pentacene-nonacene, whereas the barrier for the addition of water varies from 71 kcal/mol for benzene to 43-46 kcal/mol for pentacene-nonacene. The transition states (TSs) for the addition of water to acenes are relatively "late" on the reaction coordinate, compared to the "earlier" TSs for the addition of HCl. There is a substantial substituent effect on the energy barriers for these reactions. HCl behaves as an electrophile, with rhoHCl (vs rho p) = -4.48 and -3.39 for anthracenes and pentacenes, respectively, while water behaves as a nucleophile, with rhoHCl (vs rho p) = 2.35 and 1.39 for anthracenes and pentacenes, respectively.     

Isotope dilution high-resolution gas chromatography/high-resolution mass spectrometry method for analysis of selected acidic herbicides in surface water

In this work, an isotope dilution method for determination of selected acidic herbicides by high-resolution gas chromatography/high-resolution mass spectrometry (HRGC/HRMS) was developed for surface water samples. Average percent recoveries of native analytes were observed to be between 70.8 and 93.5% and average recoveries of labeled quantification standards [(13)C(6)]2,4-D and [(13)C(6)]2,4,5-T were 85.5 and 101%, respectively. Using this method, detection limits of 0.05 ng/L for dicamba, MCPA, MCPP, and triclopyr, and 0.5 ng/L for 2,4-D were routinely achieved. The method was applied to measuring the concentration of these analytes in surface water samples collected from five sampling locations in the Lower Fraser Valley region of British Columbia, Canada. All of the herbicides monitored were detected at varying levels in the surface water samples collected. The highest concentrations detected for each analyte were 345 ng/L for 2,4-D, 317 ng/L for MCPA, 271 ng/L for MCPP, 15.7 ng/L for dicamba, and 2.18 ng/L for triclopyr. Average detection frequencies of the herbicides were 95% for MCPA, 80% for MCPP, 70% for dicamba, 65% for 2,4-D, and 46% for triclopyr. Seasonal variations of herbicide levels are also discussed.     

Spectrophotometric and chromatographic determination of sulfanilamides in biological fluids and pharmaceuticals

The conditions for the determination of norsulfazol (I), sulfadimezine (II), ethazole (III), sulfamethoxypyridazine (IV), sulfadimethoxine (V), sodium sulfacyl (VI), sulfalene (VII), sulgin (VIII), and bucarban (IX) as their derivatives of 4,6-dinitrobenzofuroxan using spectrophotometry and thin-layer chromatography were selected. The best results were obtained at 490–500 nm using polar solvents and their aqueous mixtures of pH 6.68 as analytical media. The analytical range for sulfanilamides was 0.5–6.0 Μg/mL. The limits of detection (Μg/mL) were 0.24 for 1,0.28 for II, 0.43 for III, 0.18 for IV, 0.25 for V, 0.54 for VI, 0.54 for VII, 0.17 for VII, and 0.31 for IX. Sulfanilamides were determined in Pharmaceuticals (tablets, ointments, and drops) and biological fluids (protein hydrolyzates, urine, blood serum, and whole blood). A simple rapid method for the determination of the phenotype of biotransformation by the type of acetylation was developed based on the studies of the kinetics of the excretion of II from the human body with urine.     

Concentration factors of plutonium and americium for marine products

For a realistic dose estimation, we derived the concentration factors (CF) of plutonium and americium for the field measurements of marine products and ambient coastal sea water.The distribution of the concentration ratios (CR) between the concentration in marine products and that in ambient sea water shows a lognormal distribution. The concentration factors of plutonium and americium which are derived as the geometric mean of CR values, are 231 and 67 for whitebait, 12 and 37 for flatfish, 350 and 220 for brown algea, 140 and 670 for shell fish, 27 and 130 for cephalopods, and 250 and 550 for crustaceans, respectively.