Nax/2Bi1−x/2MoxV1−xO4 and Bi1−x/3MoxV1−xO4 New Scheelite-related phases

New Scheelite-related solid solutions of the compositions Na_x/2Bi_1−x/2Mo_xV_1−xO₄ (0≤x≤1) and Bi_1−x/3 Mo_xV_1−xO₄(0≤x≤0.2) have been synthesised by the substitution of Na and Mo at the A and B sites respectively of the ABO₄ type ferroelastic BiVO₄. The phases were characterised using chemical analysis, powder X-ray diffraction, scanning electron microscopy, EDAX, and Raman spectroscopy. While almost a continuous solid solution is obtained for the series Na_x/2Bi_1−x/2Mo_xV_1−xO₄, the absence of Na at the A-site results only in a narrow stability region for the other series, Bi_1−x/3 Mo_xV_1−xO₄ where 0≤x≤0.2. Raman spectra of selected samples at room temperature also suggest that vanadium and molybdenum atoms are disordered at the tetrahedral sites.     

Lithium insertion behaviour of Li1+xV3O8 prepared by precipitation technique in CH3OH

Li_1+xV₃O₈ (LT-M sample) was obtained by the sol-gel method in CH₃OH. This sample, prepared at 350°C, possessed a smaller grain size and better electrochemical performance than the HT sample prepared by conventional high temperature synthesis. High discharge capacity (372 mAh g⁻¹: x=4.0) and reversible discharge and charge cycles were attained owing to improvement of insertion and extraction kinetics. When heated at 200°C, CH₃OH molecules remained in the compound and crystallinity became lower by lithium insertion over x=2.0. The lithium deintercalation was irreversible.     

Phonon Raman scattering in Nd1+xBa2−xCu3O7−δ and Pr1+xBa2−xCu3O7−δ single crystals

The polarized Raman spectra of Nd_1+xBa_2−xCu₃O_7−δ (−0.023≤x≤0.107) and Pr_1+xBa_2−xCu₃O_7−δ (0.01≤x≤0.15) single crystals have been investigated. It was found that the Cu(2) A_g mode softens by 6 cm⁻¹ in Nd 1:2:3 and 4 cm⁻¹ in Pr 1:2:3 as x increases. These frequency shifts cannot be explained by the change in the relevant bond lengths due to Nd(Pr)-substitution for Ba. The variations with x of the two low frequency modes may be affected by change of their hybridization and/or change of their force constants. The linewidths of Ba mode in Pr 1:2:3 are broader than those in Y 1:2:3. This result suggests that the Pr substitution on Ba sites occurred even in a very small value of x. In x(yy) geometry the relative intensity of the Ba and O(4) modes in Nd 1:2:3 is greater than those in Pr 1:2:3. The difference between Nd 1:2:3 and Pr 1:2:3 in the relative intensity of the Ba and O(4) modes may be produced by the chains.     

Lithium insertion to ReO3-type metastable phase in the Nb2O5–WO3 system

Lithium insertion to distorted ReO₃-type metastable solid solution Nb_xW_1−xO_3−x/2 (0≤x<0.25) has been studied by chemical and electrochemical methods. In the course of lithium insertion into tetragonal compounds, transition to a cubic phase was found to occur in the region where values of y (in Li_yNb_xW_1−xO_3−x/2) fall between 0.2 and 0.3, and the phase transition was found to depend on the conditions of the reaction. Changes in OCV and lattice parameters in tetragonal region (y<0.2) were discussed from the viewpoint of the ordering of lithium ions. Also, the component diffusion coefficient of lithium in tetragonal compounds Li_0.1Nb_xW_1−xO_3−x/2 (0≤x≤0.23) was found to increase with niobium content when x≤0.10, and to saturate at 4×10⁻⁹ cm²/s.     

Material design of new lithium ionic conductor, thio-LISICON, in the Li2S–P2S5 system

A new lithium ionic conductor of the thio-LISICON (LIthium SuperIonic CONductor) family was found in the binary Li₂S–P₂S₅ system; the new solid solution with the composition range 0.0≤x≤0.27 in Li_3+5xP_1−xS₄ was synthesized at 700 °C and characterized by X-ray diffraction measurements. Its electrical and electrochemical properties were studied by ac impedance and cyclic voltammetry measurements, respectively. The solid solution member at x=0.065 in Li_3+5xP_1−xS₄ showed the highest conductivity value of 1.5×10⁻⁴ S cm⁻¹ at 27 °C with negligible electronic conductivity and the activation energy of 22 kJ mol⁻¹ which is characteristic of high ionic conduction state. The extra lithium ions in Li₃PS₄ created by partial substitution of P⁵⁺ for Li⁺ led to the large increase in ionic conductivity. In the solid solution range examined, the minimum conductivity was obtained for the compositions, Li₃PS₄ (x=0.0 in Li_3+5xP_1−xS₄) and Li₄P_0.8S₄ (x=0.2 in Li_3+5xP_1−xS₄); this conductivity behavior is similar to other thio-LISICON family with the general formula, Li_xM_1−yM_y′S₄ (M=Si, Ge, and M′=P, Al, Zn, Ga, Sb). Conduction mechanism and the material design concepts are discussed based on the conduction behavior and the structure considerations.     

Oxygen nonstoichiometry and phase transitions of the neodymium-rich Nd1+xBa2−xCu3Oz solid solution

On the basis of chemical, thermal analysis and Cu K-edge X-ray absorption measurements, oxygen content in the Nd_1+xBa_2−xCu₃O_z solid solution was determined between 1000°C in air and 400°C in oxygen for x=0.05–0.9 compositions. It has been observed that the oxygen nonstoichiometry Δz of the Nd_1+xBa_2−xCu₃O_7+x/2−Δz solid solution decreases 2–2.5 times for a large substitution (Δz≈0.3–0.33 for x=0.9), despite of the acclaimed higher total oxygen content. The difference in nonstoichiometry is explained by a higher average value of the copper oxidation state (ACV), which is vital for the solid solution with large x even at elevated temperatures (ACV≈2–2.05 for x>0.3 at 1000°C, PO₂=0.21 atm). On the contrary, the ACV after complete oxygenation is almost constant (about 2.25–2.3) for the whole series. The x-dependence of the oxygen content is not monotonous and structural phase transitions can be observed at x=0.3 and x=0.6, as confirmed by the X-ray diffraction and the Raman scattering spectroscopy. The first well-known transition is connected with the oxygen disorder due to the Nd substitution for Ba at random Ba-sites. In the present work, it is proved by the apical oxygen mode broadening in Raman spectra. Ordering of the Nd and Ba atoms with a subsequent orthorhombic distortion of the lattice may occur even at 1000°C in air due to the second transformation at x≈0.6. The invariable orthorhombicity of the Nd-rich solid solution with x>0.6 is not caused by the oxygen absorption as in the x=0.05 case. Existence of high- and low-temperature orthorhombic modifications of this solid solution has been observed for the first time. Finally, a tentative 3D (z–x–T) diagram is suggested for the Nd_1+xBa_2−xCu₃O_z solid solution up to 1000°C in air, including the new x=0.6–0.9 region.     

Synthesis and characterization of the Aurivillius phases Bi2 − xPbxSr1 − xNdxNb2O9

The n = 2 Aurivillius phase Bi_{2 − x}Pb_xSr_{1 − x}Nd₂O₉ was successfully synthesized as a ceramic material over the whole range of simultaneous, charge compensated substitution x = 0–1.0. Structural investigations were performed by Rietveld refinement applying different space groups Fmmm and A2₁am, and additionally by X-ray absorption spectroscopy (EXAFS) on the Nd L_III-edge, confirming the accommodation of Nd on the atomic sites of Sr, which implies the substitution of Bi³⁺ by the isoelectronic Pb²⁺. The ferroelectric transition temperature T_c = 270 °C of the substituted powders with x = 0.4 and 1.0 is distinctly reduced compared to the unsubstituted sample with T_c = 450 °C. In temperature resolved powder X-ray diffraction patterns no structural phase transition could be detected.     

A solid-state V NMR characterization of vanadium sites in LiCoxNi1−xVO4

LiCo_xNi_1−xVO₄ compounds (x=0, 0.2, 0.5, 0.8, 1.0) have been prepared for lithium ion batteries by different preparation methods, namely, wet-chemistry (WC) and solid-state (SS) routes. ⁵¹V nuclear magnetic resonance (NMR) has been employed to accurately assess the vanadium environments in these materials and results show that vanadium atoms are distributed in octahedral and tetrahedral sites. The fractions of vanadium atoms in tetrahedral/octahedral sites depends on composition and sample preparation conditions. The tetrahedral site, which is particularly dominant in samples produced via the WC route, is more affected by paramagnetic interactions and its ⁵¹V NMR spectrum is essentially Gaussian in shape. The octahedral site, on the other hand, exhibits first-order quadrupolar broadened satellites. Even though tetrahedral sites for a given x are comparable for WC and SS materials, there are some differences amongst octahedral environments, namely in the distributions of quadrupolar broadened satellites. The larger satellite distribution observed for WC materials is indicative of a larger distribution of structural defects for these as compared to SS materials.     

Oxygen diffusion and surface exchange in La1−xSrxFe0.8Cr0.2O3−δ (x=0.2, 0.4 and 0.6)

Oxygen tracer diffusion (D*) and surface exchange rate constant (k*) have been measured, using isotopic exchange and depth profiling by secondary ion mass spectrometry (SIMS), in La_1−xSr_xFe_0.8Cr_0.2O_3−δ (x=0.2, 0.4 and 0.6). Measurements were made as a function of temperature (700–1000 °C) and oxygen partial pressure (0.21–10⁻²¹ atm) in dry oxygen, water vapour and water vapour/hydrogen/nitrogen mixtures. At high oxygen activity, D* was found to increase with increasing temperature and Sr content. The activation energies for D* in air are 2.13 eV (x=0.2), 1.53 eV (x=0.4) and 1.21 eV (x=0.6). As the oxygen activity decreases, D* increases as expected qualitatively from the increase in oxygen vacancy concentration. Under strongly reducing conditions, the measured values of D* at 1000 °C range from 10⁻⁸ cm² s⁻¹ for x=0.2 to 10⁻⁷ cm² s⁻¹ for x=0.4 and 0.6. The activation energies determined at constant H₂O/H₂ ratio are 1.21 eV (x=0.2), 1.59 eV (x=0.4) and 0.82 eV (x=0.6).

The surface exchange rate constant of oxygen for the H₂O molecule is similar in magnitude to that for the O₂ molecule and both increase with increasing Sr concentration.     

The relationship between crystal structure and electrical conductivity in the LaY1−xInxO3 (x=0.0–0.7) system

The electrical conductivity of the LaY_1−xIn_xO₃ (x=0.0–0.7) system has been studied from the viewpoint of crystal chemistry. The high temperature form of LaYO₃ (x=0.0) was ascertained to be the Sm₂O₃-type (B-type rare earth) structure, not perovskite-type one. The X-ray diffraction (XRD) experiments revealed that the samples with x=0.05 and 0.10 were the mixed phase of Sm₂O₃-type and perovskite-type structure, and changed to perovskite phase in the range of x0.20. From oxygen partial pressure dependence of the electrical conductivity, it was found that both the Sm₂O₃-type and the perovskite-type single phases showed hole conduction, but the mixed phase did oxide-ion one. The electrical conductivity of the LaY_1−xIn_xO₃ (x=0.0–0.7) system increased with increasing x, and showed the maximum value in the range of x=0.05–0.10, and then decreased with increasing x. The occurrence of oxide-ion conduction was discussed from the viewpoint of lattice distortion in the mixed phase.     

Magnetic behavior of Pr1 − xMxCo5 compounds (M = Ti, Zr and Hf)

Magnetic characteristics of Ti-, Zr- and Hf-substituted PrCo₅ alloys have been studied over the temperature range from 77 to 300 K and for applied fields up to 20 kOe. It is established that Ti, Zr and Hf substitute for Pr. Single-phase materials are formed for all values of x up to 0.2 in the system Pr_1−xZr_xCo₅ but for x only up to 0.1 for Pr_1−xTi_x Co₅ and Pr_1−xHfxCo₅ alloys. Larger amounts of Zr can be substituted if the material is made hyperstoichiometric in Co, e.g., Pr_0.7Zr_0.3Co_5.5. All the alloys show a decrease in magnetic moment and an increase in Curie temperature as x increases. Anisotropy fields decrease as x increases at 295 K. Anomalous behavior is observed at 77 K, suggested that these ternary alloys may have a cone structure at this temperature.     

Oxygen overdoping in superconducting and non-superconducting Y1−xPrxBa2Cu3Oy

We present the evolution of magnetic and structural properties of Y_1−xPr_xBa₂Cu₃O_y (x0.5 and x=1) single crystals and polycrystalline materials when the oxygen concentration y is varied from under- to overdoping. We have found a monotonous evolution of the Pr Néel temperature for x=1 samples and a maximum of the superconducting critical temperature for the x0.5 samples. The structural properties as detected by X-ray diffraction and Raman spectroscopy show no instabilities when crossing the optimal doping region as was found in the x=0 material.     

Oxygen tracer diffusion in La1 − xSrxCoO3

Tracer diffusion of ¹⁸O in dense, polycrystalline La_1−xSr_xCoO₃ for x = 0.1 has been measured in the temperature range 400 to 600 °C and at 500 °C for x = 0.2 at an oxygen partial pressure of 1 × 10⁵ Pa. Depth profiles were obtained by secondary ion mass spectrometry. The diffusion coefficient for La_0.9Sr_0.1CoO₃ is given by D = (17–247) exp[(−232 ± 8 kJ/mole)/RT] cm²/s. This value is several orders of magnitude lower than D extrapolated from the results for x = 0.2 measured in the 700–900 °C temperature range. One possible explanation for the discrepancy is that the two measurements reflect different diffusion paths. As expected, La_0.8Sr_0.2CoO₃ exhibits a higher diffusivity at 500 °C than does La_0.9Sr_0.1CoO₃.     

A spectroscopic ellipsometric investigation of new critical points of Zn1−xMnxS epilayers

Zn_1−xMn_xS epilayers were grown on GaAs (1 0 0) substrates by hot-wall epitaxy. X-ray diffraction (XRD) patterns revealed that all the epilayers have a zincblende structure. The optical properties were investigated using spectroscopic ellipsometry at 300 K from 3.0 to 8.5 eV. The obtained data were analyzed for determining the critical points of pseudodielectric function spectra, (E) = ₁(E) + i₂(E), such as E₀, E₀ + Δ₀, and E₁, and three E₂ (Σ, Δ, Γ) structures at a lower Mn composition range. These critical points were determined by analytical line-shapes fitted to numerically calculated derivatives of their pseudodielectric functions. The observation of new peaks, as well as the shifting and broadening of the critical points of Zn_1−xMn_xS epilayers, were investigated as a function of Mn composition by ellipsometric measurements for the first time. The characteristics of the peaks changed with increasing Mn composition. In particular, four new peaks were observed between 4.0 and 8.0 eV for Zn_1−xMn_xS epilayers, and their characteristics were investigated in this study.     

Short-range order and F ion diffusion inside the Pb1 − xAlxF2 + x solid solution Part II: Al NMR investigation and proposal of clustering process

A ²⁷Al nuclear magnetic resonance (NMR) investigation at room temperature of the Pb_{1 − x}Al_xF_{2 + x} (0 ≤ x ≤ 0.12) solid solution and of the ordered Pb₉Al₂F₂₄ phase is carried out. Two different types of aluminium ions are identified and their ratio is determined as a function of x. A clustering process based on the formation of column clusters, more and more extended when x increases, is proposed on the basis of results issued from the ¹⁹F (Part I) and ²⁷Al NMR investigations.     

Ca1−xYxMnO3 manganites: synthesis and ESR characterization

Ceramic samples of Ca_1−xY_xMnO₃ were synthesized by a liquid-mix method obtaining single phase materials, for 0.1x1, with orthorhombic structure. The cell volume increases with x indicating that changes in the Mn electronic state overcomes the progressive diminishing of the (Ca, Y) cationic radius, r_Ca>r_Y. We observed a continuous broadening of the electronic spin resonance line width with x. This is explained in terms of the increasing orthorhombic distortions. We have measured the DC magnetization for the x=1 compound YMnO₃. Our results are compatible with a G-type antiferromagnet with T_N=44 K.     

Magnetic properties of PuNi3 type intermetallic compounds YxZr1−xCo2.9 and their hydrides

Magnetization and Curie temperature of Y_xZr_1−xCo_2.9 decrease with decreasing x. Their hydrides with x0.8 are paramagnetic with an anomaly and those of 0.7x0.5 become weak ferromagnets. The spin structure is discussed.     

Thermodynamic analysis of BaxK1 − xBiO3 using the Eliashberg theory

In order to understand the mechanism that gives rise to superconductivity in the ceramic superconductors of the type Ba_xK_{1 − x}BiO₃, we analyze the thermodynamic properties with the use of the Eliashberg equations. For these calculations we used the electron-phonon spectral density function ²(ω)F(ω), calculated by Shirai et al. [1] from first principles for two different K concentrations, x=0.5 and x=0.7.     

Trapping mechanism of superconductivity suppression induced by Pr substitution in the Ho1−xPrxBa2Cu3O7−δ system

Pr concentration dependence of the superconducting transition temperature T_c in the Ho_1−xPr_xBa₂Cu₃O_7−δ system is determined from measurements of DC electrical resistance. This dependence coincides with that for the parallely studied Y_1−xPr_xBa₂Cu₃O_7−δ reference system. Both systems have the same value of the critical concentration x_c=0.58, in accordance with nearly equal ionic radii of Ho³⁺ and Y³⁺ ions. It has been shown that the T_c(x) curve can be described with a single mechanism based on a decreasing number of sheet holes trapped by Pr^IV-ions, if one takes also into account that the number of these ions changes with x.     

Influence of Nd substitution on the superconducting properties of ceramics in the 2212 system Bi2−wPbwSr2−xCa1−yNdx+yCu2O8+z

In the system Bi_2−wPb_wSr_2−xCa_1−yNd_x+yCu₂O_8+z different fractions of Nd are substituted on either Sr of Ca sites in order to introduce intrinsic insulating pinning centres. It is shown that a Nd concentration around x or y = 0.2 is likewise favourable with an average Nd---Nd distance in the range of the coherence length in the a, b-plane. However, clear evidence of flux pinning is only present for charge compensation with Pb²⁺. A simultaneous substitution of the Bi-based 2212 superconductor with moderate amounts of Nd³⁺ and Pb²⁺ improves the superconducting properties by strengthening the flux pinning forces.