Preconcentration of uranium(VI) by solid phase extraction onto dicyclohexano-18-crown-6 embedded benzophenone

Summary The preparation of a solid phase extractant (SPE), dicyclohexano-18-crown-6 embedded benzophenone, for preconcentration of uranium(VI) is described. The uranium(VI) can be quantitatively retained from 0.5 l solution on 1% dicyclohexano-18-crown-6 embedded benzophenone in the pH range 6.0-7.0, and then eluted with 5.0 ml of 1M HCl. Uranium(VI) content of the eluent was determined spectrophotometrically by Arsenazo III. Calibration graphs are rectilinear over the uranium(VI) concentration in the range of 0.004-0.4mg^.ml^-1. Five replicate determinations of 40mg of uranium(VI) present in 0.5 l sample gave a mean absorbance of 0.185 with a relative standard deviation of 2.45%. The detection limit corresponding to three times the standard deviation of the blank was found to be 2.0mg^.l^-1. The accuracy of the developed preconcentration procedure was tested by analyzing standard marine sediment reference material. The uranyl ion content of soils and sediments was estimated spectrophotometrically after the preconcentration procedure and compared to the results gained by standard inductively coupled plasma mass spectrometry (ICP-MS).     

Solvent extraction of uranium(VI) into toluene by dicyclohexano-18-crown-6 from mixed aqueous-organic solutions

Extraction behaviour of uranium(VI) from mixed organo-aqueous solutions containing water-miscible protic aliphatic alcohols and several aprotic solvents was investigated by using dicyclohexano-18-crown-6(DC18C6) as an extractant. The organic phase was a binary solution of DC18C6 and toluene while the polar phase was a three component solution of uranyl nitrate, polar additive and aqueous nitric acid. Methanol, ethanol, isobutanol, dioxane, acetone, propylene carbonate and acetonitrile were used as the organic components of the mixed (polar) phase. Propylene carbonate, acetone, acetonitrile and dioxane increased the extractability of U(VI), whereas alcoholic additives showed only an antagonistic effect. The relative increase in extraction was found to be more at lower nitric acid concentrations. Possible reasons for such behaviour are briefly discussed. Recovery of U(VI) from loaded organic phase was easily accomplished using dilute perchloric acid and sulphuric acid. A sample method was standardized for the separation of plutonium(IV) from uranium(VI) based on its reductive stripping.     

Solvent extraction separation of rubidium with dicyclohexano-18-crown-6

Rubidium is extracted quantitatively at pH 3.0-7.0 by 0.01M dicyclohexano-18-crown-6 in methylene chloride from 0.01M picric acid, stripped with 2M nitric acid and determined by flame photometry or atomic-absorption spectrometry. It can be separated from the most alkali and alkaline-earth metals, but the tolerance levels for potassium, ammonium and barium are rather low. The common anions, including those of some organic acids, are tolerated in fairly high amounts. The method has been applied to analysis of chloride schist rock and lepidolite for rubidium. The analysis takes an hour.     

Separation of uranium(VI) as chloride complex by solvent extraction with dicyclohexyl-18-crown-6

Uranium(VI) was quantitatively extracted from 6 to 8M hydrochloric acid with 0.02M DC-18-crown-6 in chloroform. It was stripped from the organic phase with 0.5M hydrochloric acid and determined as its Arsenazo-III complex at 665 nm. Uranium(VI) was separated from several elements such as thorium, zirconium, scandium, yttrium, thallium and tin in complex mixtures. The method was extended for analysis of uranium in monazite and rock sample.     

Synergistic extraction of uranyl ion with acylpyrazolones and dicyclohexano-18-crown-6

Synergistic extraction of uranyl ion with acylpyrazolones such as 1-phenyl-3-methyl-4-trifluoroacetylpyrazolone-5 (HPMTFP, pKa=2.7), 1-phenyl-3-methyl-4-acetylpyrazolone (HPMAP, pKa=3.8) or 1-phenyl-3-methyl-4-benzoylpyrazolone-5 (HPMBP, pKa=4.2) in combination with dicyclohexano-18-crown-6 (DC-18-C6) has been studied at various fixed temperatures. The results indicate that the equilibrium constants of the organic phase addition reaction, log Ks, at 30°C are almost constant, viz., 2.72, 2.69 and 2.84, respectively, for the above three systems. The similarity and low log Ks values with DC-18-C6 as compared with TBP systems with these pyrazolones appears to arise due to the limitation to the approach of the large crown ether molecule in bonding with the uranyl chelate. This is in contrast to the fact that the relative basicities of the two donors (equilibrium constant for nitric acid uptake) are comparable. Thermodynamic data for chelate extraction with HPMTFP evaluated by the temperature coefficient method indicates that a hydrated chelate is extracted into the organic phase. Also, the organic phase addition reaction with DC-18-C6 is stabilized by exothermic enthalpy change, the entropy change counteracting in all the three cases.     

Reaction of lead halides with 18-crown-6 and dicyclohexano-18-crown-6: Solvent extraction,synthesis and crystal structure of [Pb(18-crown-6)I2]

Abstract

Solvent extraction of lead halides with 18-crown-6 (18C6), dicyclohexano-18-crown-6 (DC18C6, cis-syn-cis and cis-anti-cis isomers) in chloroform was studied, and the extraction constants corrected for side reactions and ionic strength effects were obtained. The compounds of the same composition as those being extracted were also isolated in crystal form. The molecular structure of the [Pb(18C6)I₂] complex has been determined. Crystals are monoclinic, P2₁/n, a = 11.237(2), b = 10.992(2), c = 8.139(2)Å, β = 97.32(3)°, V = 997.1(7)ų, D_calc = 2.416(2)gcm^?3, Z = 2 for the composition C₁₂H₂₄O₆PbI₂. The final R-factor is 0.043 for 558 unique reflections. The lead atom is coordinated to six oxygen atoms of the crown ether and two iodine atoms forming a hexagonal bipyramidal coordination polyhedron. The 18C6 molecule and the two halogen atoms form a hydrophobic coating for the lead atom which may be assumed to be the main reason of high extraction constants of the iodine complexes. For 10-coordinate lead ion (bidentate counter ions) the cis-syn-cis isomer of DC18C6 appears to be the best extraction reagent, while for 8-coordinate lead ion (monodentate halide anion) no difference between isomers was observed.     

Solvent extraction of uranium(VI) using dibenzo-18-crown-6 in nitrobenzene from ammonium thiocyanate medium

Solvent extraction of uranium(VI) from aqueous solutions of ammoniumthiocyanate has been investigated in the presence of dibenzo-18-crown-6. Uranium(VI)was quantitatively extracted from 1.0M ammonium thiocyanate using 0.01M dibenzo-18-crown-6in nitrobenzene. Back extraction of U(VI) was quantitative with various strippingagents. Separation of U(VI) from other elements was achieved from binary aswell as multicomponent mixtures. Uranium was determined in monazite sand andsyenite rock samples. The method is very simple, rapid and highly reproducible(approximately ±2%).     

PVC-based dicyclohexano-18-crown-6 sensor for La(III) ions

A new ion-selective electrode (ISE) based on dicyclohexano-18-crown-6 (DC18C6) as a neutral carrier is developed for lanthanum(III) ions. The electrode comprises of dicyclohexano-18-crown-6 (6%), PVC (33%), and ortho-nitrophenyl octyl ether (o-NPOE) (61%). The electrode shows a linear dynamic response in the concentration range of 10⁻⁶ to 10⁻¹ M with a Nernstian slope of 19 mV per decade and a detection limit as 5×10⁻⁷ M. It has a response time of <30 s and can be used for at least 5 months without any significant divergence in potentials. The selectivity coefficients for mono-, di-, and trivalent cations indicate good selectivity for La(III) ions over a large number of interfering cations. The sensor has been used as an indicator electrode in the potentiometric titrations of La(III) with EDTA. The membrane is successfully applied in partially non-aqueous medium. It can be used in the pH range 4-9.     

Solvent extraction separation of thorium as picrate complex with 18-crown-6

Thorium was quantitatively extracted from 0.04M picric acid with 0.065M of 18-crown-6 at pH 2.0–3.5. It was stripped from organic phase with 0.5M nitric acid and was determined spectrophotometrically at 655 nm as its Arsenazo-III complex. Thorium was separated from mixture containing cerium, uranium, zirconium, hafnium, yttrium and lead in complex mixtures. The method was extended for the analysis of thorium in monazite.     

Solvent extraction of calcium into nitrobenzene by using hydrogen dicarbollylcobaltate in the presence of dicyclohexano-18-crown-6 and dicyclohexano-24-crown-8

Extraction of microamounts of calcium by a nitrobenzene solution of hydrogen dicarbollylcobaltate (H⁺B^?) in the presence of dicyclohexano-18-crown-6 (DCH18C6, L) and dicyclohexano-24-crown-8 (DCH24C8, L) has been investigated. The equilibrium data have been explained assuming that the species HL⁺, $ {\text{HL}}_{2}^{ + },$ CaL²⁺ and $ {\text{CaL}}_{2}^{2 + } $ (L = DCH18C6, DCH24C8) are present in the organic phase. The values of extraction and stability constants of the complex species in nitrobenzene saturated with water have been determined. It was found that the stability constants of CaL²⁺ (L = DCH18C6, DCH24C8) for both ligands under study are practically the same in nitrobenzene saturated with water, whereas in this medium the stability of the complex $ {\text{CaL}}_{2}^{2 + } $ involving the DCH24C8 ligand is somewhat higher than that of $ {\text{CaL}}_{2}^{2 + } $ with the ligand DCH18C6.     

Analytical application of poly [dibenzo-18-crown-6] for chromatographic separation of thorium(IV) from uranium(VI) and other elements in glycine medium

A selective and effective chromatographic separation method for thorium(IV) has been developed by using poly [dibenzo-18-crown-6] as stationary phase. The separations are carried out from glycine medium. The sorption of thorium(IV) was quantitative from 1 × 10^?2 to 1 × 10^?4 M glycine. The elution of thorium(IV) was quantitative with 2.0–8.0 M HCl, 4.0–7.0 M HBr, 1.0–2.0 M HClO₄ and 5.0 M H₂SO₄. The capacity of poly [dibenzo-18-crown-6] for thorium(IV) was found to be 0.215 ± 0.01 mmol/g of crown polymer. The effect of concentration of glycine, metal ion, foreign ion and eluents has been studied. Thorium(IV) was separated from a number of cations in ternary as well as in multicomponent mixtures. The applicability of the proposed method was checked for the determination of thorium(IV) in real as well as geological sample. The method is simple, rapid, and selective with good reproducibility (approximately ±2 %).     

二环己基-18-冠-6异构体A与铀的萃取配合物的结构研究

二环己基-18-冠-6-异构体Δ(dcc)在盐酸体系中萃取UO2Cl2和UCl4时, 形成的配合物晶体的组成分别为(C20H36O6.H3O)2UO2Cl4.2C6H6(1)和(C20H36O6.H3O)2UCl6(2). 结构分析证实, 在1和2中, U(VI)和U(IV)均未与冠醚直接配位, 而是分别形成配阴离子四氯铀铣(II)和六氯化铀(II). 而配阳离子均由冠醚环的三个氧原子与H3^+O以较强的氢键键合, 将H3O^+稳定于冠醚环中, 成为配阳离子dcc.H3O^+. 由静电吸收及Van der Waals力形成稳定的晶体.     

Solvent extraction separation of uranium(VI) with dibenzo-24-crown-8

Uranium(VI) was quantitatively extracted with 0.01M DB-24-crown-8 in nitrobenzene from 6 to 10M hydrochloric acid. From the organic phase uranium was stripped with 2M nitric acid and determined spectrophotometrically with PAR at 530 nm. Uranium(VI) was separated from a large number of elements in binary mixtures as well as from multicomponent mixtures. The method was extended to the analysis of uranium in geological samples and animal bone.     

The extraction equilibrium of uranium(VI) with i-butyldodecylsulfoxide (BDSO)

The i-butyldodecylsulfoxide (BDSO) was synthesized. The extraction of uranium(VI) has been carried out with BDSO in toluene from various HNO₃ concentrations. It was found that the distribution ratio increases with increasing nitric acid concentration up to 3.0 mol/l and then decreases. The distribution ratios also increase with increasing extractant concentration. The extracted species appears to be UO₂(NO₃)₂·2BDSO and the equilibrium constant value is 15.2. The influence of temperature, sodium nitrate and oxalate concentrations on the extraction was also investigated, and the thermodynamic functions of the extraction reaction were obtained.This revised version was published online in November 2005 with corrections to the Cover Date.     

Solvent extraction of amino acids into a room temperature ionic liquid with dicyclohexano-18-crown-6

Amino acids Trp, Gly, Ala, Leu are extracted efficiently from aqueous solution at pH 1.5–4.0 (Lys and Arg at pH 1.5–5.5) into the room temperature ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (BmimPF₆) with dicyclohexano-18-crown-6 (CE). The most hydrophilic amino acids such as Gly are extracted as efficiently as the less hydrophilic (92–96%). The influence of pH, amino acid and crown ether concentration, volume ratio of aqueous and organic phases, and presence of some cations on amino acid recovery were studied. The ratio of amino acid to crown ether in the extracted species is 1:1 for cationic Trp, Leu, Ala, and Gly and to 1:2 for dicationic Arg and Lys. This ionic liquid extraction system was used successfully for the recovery of amino acids from pharmaceutical samples and fermentation broth, and was followed by fluorimetric determination.These results were published in part in Smirnova SV (2002) Ph.D. Thesis, Moscow State University.     

Extraction of rare-earth elements by alkylated dibenzo-18-crown-6 and dicyclohexano-18-crown-6 from acid solutions

The extraction of rare-earth elements (REE) by alkylated crown ethers (dibenzo-and dicyclohexano-18-crown 6; DB18C6 and DCH18C6) from acid solutions in the chloroform-water system is studied. The extraction of the REE with DCH18C6 and its alkylated derivatives in the presence of trichloroacetic acid (TCA) is far more efficient than the extraction with DB18C6 and its alkylated derivatives or when nitric or acetic acid is used instead of TCA. The distribution coefficients for the cerium metals are far higher than for the yttrium metals. The metal: crown ether ratio in the extracted complex in all cases is 1:1.     

Interaction between thallium(III) bromide and dicyclohexano-18-crown-6 immobilized on silica

The adsorption of cis-syn-cis-dicyclohexano-18-crown-6 on silica gel from organic solvents was studied. In the adsorption from chloroform solutions, the immobilization of the reagent molecules at the surface was coplanar. Hydrogen bonds between surface silanol groups and oxygen atoms of the polyether ring of the crown ether play an important role in the immobilization of the reagent. The reaction between thallium(III) bromide and the immobilized reagent was studied. The composition of complex compounds formed at the surface of the modified adsorbent was found. A procedure was proposed for the sorption-spectrophotometric determination of thallium(III) (≥0.05 mg/L) in the presence of heavy metal ions.     

Liquid-liquid extraction of thorium(IV) and uranium(VI) with three ether-amide type tripodands

N,N,N',N',N',N'-Hexaethyl-2,2′,2'-(nitrilotrisethyleneoxy-2-benzyloxy)tris(acetamide) (L3) has been prepared and characterized by using IR, ¹H NMR and positive-ion FAB mass spectra. The extraction of Th⁴⁺ and UO₂ ²⁺ with N,N,N',N',N',N'-hexaethyl-2,2',2'- (nitrilo-trisethyleneoxy)tris(acetamide) (L1), N,N,N',N',N',N'-hexaisopropyl-2,2',2'-(nitrilotrisethyleneoxy)tris(acetamide) (L2), and L3 was studied at 20±1 °C as a function of diluent, concentration of free extractant in organic phase and concentration of picrate in aqueous phase. It was found that the extracting powers of L1 and L2 for Th⁴⁺ are almost identical. The extracting power of L2 for UO22+ was slightly higher than that of L1. The difference in terminal groups (ethyl or isopropyl) of the extractants (L1 and L2) with same backbone has a little effect on the extracting power for both Th4+ and UO22+. The extracting powers of L3 for both Th4+ and UO22+ were larger than those of L1 and L2. The extractants (L1 and L3) having the same terminal group (ethyl) with different backbones have obviously different extracting powers for Th4+ or UO22+. The extracting powers of all three extractants L1, L2, and L3 for Th4+ were larger than those for UO22+. The compositions of extracted species in organic phase were predominantly ThL(Pic)3NO3 and UO2L(Pic)NO3, respectively (L denotes L1, L2 and L3). This revised version was published online in July 2006 with corrections to the Cover Date.