Triphenylphosphine oxide-based bismaleimide and poly(bismaleimide): Synthesis,characterization, and properties

A novel phosphorus-containing bismaleimide, 3,3′-bis(maleimidophenyl)phenylphosphine oxide (BMPPPO), was synthesized from triphenylphosphine oxide. This bismaleimide exhibited good solubility in common organic solvents, such as methylethylketone, methylisobutylketone, dichloromethane, chloroform, tetrahydrofuran, acetone, methanol, ethanol, and hot toluene. A low melting point (T_m = 148 °C), a relatively low polymerization temperature (T_p = 214 °C), and a wide processing window (T_p − T_m = 66 °C) were also obtained for BMPPPO. This implies better processing capability. In contrast to most known phosphorus-containing polymers, the incorporation of BMPPPO into poly(bismaleimide) enhanced the polymer glass-transition temperature. Thermal stability at temperatures over 550 °C and char yields in the high-temperature region over 700 °C were also improved. As a result, the flame-retardant properties of the poly(bismaleimide)s were improved. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1716–1725, 2001     

Which Polyesters Can Mimic Polyethylene?

Self‐metathesis of erucic acid by [(PCy₃)(η‐C‐C₃H₄N₂Mes₂)Cl₂Ru = CHPh] (Grubbs second‐ generation catalyst) followed by catalytic hydrogenation and purification via the ester yields 1,26‐hexacosanedioate (>99% purity). Polyesterification with 1,26‐hexacosanediol, generated from the diester, affords polyester‐26,26, which features a T_m of 114 °C (T_c = 92 °C, ΔH_m = 160 J g⁻¹). Ultralong‐chain model polyesters‐38,23 (T_m = 109 °C) and −44,23 (T_m = 111 °C), generated via multistep procedures including acyclic diene metathesis polymerization, underline that melting points of such aliphatic polyesters do not gradually increase with methylene sequence chain length. Available data suggest that to mimic linear polyethylenes thermal properties, even longer sequences, amounting to at least four times a fatty acid chain, fully incorporated in a linear fashion are required.     

Fully aromatic liquid crystalline homopolyesters and copolyesters of 1,1′-binaphthyl-4,4′-diol

A series of fully aromatic, thermotropic polyesters based on 1,1′-binaphthyl-4,4′-diol, BND, was prepared by the melt polycondensation method and characterized for their thermotropic behavior by a variety of experimental techniques. The homopolymer of BND with terephthalic acid formed a nematic melt at 353°C. In contrast, the polyester from BND and 2,6-naphthalenedicarboxylic acid had a melting transition, T_m, above 400°C, so it was not possible with the equipment available to determine whether it formed a nematic melt. All of the copolymers of BND formed nematic melts at much lower T_m values than those of its respective homopolymers, as expected, because of the copolymerization effect of the added monomer. Moreover, all of the copolymers had higher glass transition temperatures, T_g, than those of other liquid crystalline polyesters and higher thermal stabilities. © 1994 John Wiley & Sons, Inc.     

Fully aromatic thermotropic liquid crystalline polyesters of substituted 4,4′-biphenols. IV. Homopolyesters with terephthalic acid and copolyesters with terephthalic acid and 4-hydroxybenzoic acid

A series of fully aromatic thermotropic polyesters based on mono-, di-, and tetra-substituted biphenols was prepared by the melt polycondensation method and examined for their thermotropic behavior by a variety of experimental techniques. The homopolyesters obtained from substituted biphenols containing either one phenyl or two phenyl groups as substituent(s) and TA formed nematic melts, but the homopolymers of the substituted biphenols containing either four sec-butyl groups or two tert-butyl groups with TA had melting transitions, T_m, above 400°C. Thus, it was not possible to determine whether they formed nematic melts. On copolymerization with 30 mol % HBA most of the resulting copolyesters had much lower T_m values, compared to those of respective homopolyesters, and the copolymers of the biphenol monomer containing the tert-butyl groups formed a nematic melt at an observable temperature. However, the copolymer of the biphenol with sec-butyl groups still had a T_m above 400°C. © 1993 John Wiley & Sons, Inc.     

Polymerization of N-(p-aminobenzoyl)caprolactam: Block and alternating copolymers of aromatic and aliphatic polyamides

The polymerization behavior of N-(p-aminobenzoyl)caprolactam was studied. It was found that polymerization could proceed by either elimination of caprolactam or by ring opening. Polymers prepared at temperatures above 200°C showed a greater tendency for ring opening to produce alternating aromatic/aliphatic copolymers than did polymers prepared at lower temperatures. Block copolymers of poly(p-benzamide) and nylon 6 were prepared by a two-stage hydrolytic polymerization process or by anionic polymerization at temperatures > 200°C. Polymer microstructures were determined using ¹³C-NMR spectroscopy by comparison with homopolymers and model alternating copolymers. The alternating copolymer prepared by condensation of N-(p-aminobenzoyl)-6-caproic acid showed a melting transition at 300–305°C in the DSC and a T_g in subsequent heating cycles of 116–119°C. Copolymers made with the two-stage process were rich in p-benzamide sequences and showed no T_g or T_m below 400°C. Copolymer made with NaH was rich in nylon 6 units, showed a T_m of 175–180°C and a T_g of 80–81°C, and was homogeneous in both the melt and solid.     

Layer structures. VI. Chiral sanidic polyesters derived from 2,5-bis (dodecyloxy) terephthalic acids and 4,4′-dihydroxybiphenyl

Copolycondensations of (S,S)-2,5-bis(2-methylbutyloxy) terephthaloylchloride with 2,5-bis(dodecyloxy)terephthaloylchloride and with 4,4′-bistrimethylsiloxybiphenyl yielded a series of novel chiral thermotropic copolyesters. These polyesters were characterized by elemental analyses, inherent viscosities, ¹H-NMR spectroscopy, optical rotations, optical microscopy, DSC measurements, and WAXS powder patterns recorded with synchrotron radiation under variation of the temperature. All homo- and copolyesters formed a solid sanidic layer structure with melting temperatures (T_m) ≥ 200°C. A broad enantiotropic nematic or cholesteric phase is formed above T_m with isotropization temperatures (T_is) in the range of 275–325°C. Yet, the T_m of the chiral homopolyester is so high (378°C) that the melting process is immediately followed by rapid degradation. The cholesteric phases of the copolyesters displayed unusual mobile schlieren textures, but a stable Grandjean texture was never obtained. Cholesteric domains consisting of loose bundles of more or less helical main chains are discussed as supramolecular order responsible for the observed textures and their pronounced temperature dependence. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 947–957, 1997     

Effects of polymerization method on structure and properties of thermoplastic polyurethanes

The effects of the dynamic polymerization method and temperature on the molecular aggregation structure and the mechanical and melting properties of thermoplastic polyurethanes (TPUs) were successfully clarified. TPUs were prepared from poly (ethylene adipate) glycol (M_n = 2074), 4,4′‐diphenylmethane diisocyanate and 1,4‐butanediol by the one‐shot (OS) and the prepolymer (PP) methods in bulk at dynamic polymerization temperatures ranging from 140 to 230 °C. Glass‐transition temperatures (T_gs) of the soft segment and melting points (T_ms) of the hard segment domains of OS‐TPUs increased and decreased, respectively, with increasing polymerization temperatures, but those of PP‐TPUs were almost independent of the polymerization temperature. T_gs of the soft segment and T_ms of the hard segment domains of these TPUs polymerized above 190 °C were almost the same regardless of the polymerization method. Solid‐state nuclear magnetic resonance spectroscopy (NMR) analyses of OS‐ and PP‐TPUs showed that the relative proton content of fast decay components, which corresponds to the hard segment domains, in these TPUs decreased with increasing polymerization temperatures. These results clearly show that the degree of microphase separation becomes weaker with increasing polymerization temperatures. The temperature dependence of dynamic storage modulus and loss tangent of OS‐TPUs coincided with those of PP‐TPUs at polymerization temperature above 190 °C. The apparent shear viscosity for OS‐ and PP‐TPUs polymerized above 190 °C approached a Newtonian behavior at low shear rates regardless of the polymerization method. These results indicate that TPUs polymerized at higher temperatures form almost the same molecular aggregation structures irrespective of the dynamic polymerization method. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 800–814, 2007     

Melting behavior of poly(ether ether ketone) in its blends with poly(ether imide)

We detail the melting behavior of poly(ether ether ketone) (PEEK) and investigate its melting behavior in miscible blends with poly(ether imide) (PEI). The determination of the equilibrium melting point (T_m⁰) of PEEK is discussed by considering its inhomogeneous morphology. T_m⁰ is obtained by a long extrapolation of a Hoffman–Weeks plot to 384°C. Hindrance of PEEK crystal reorganization induced by PEI during heating is observed over the blend composition investigated (20–75 wt % PEEK). This behavior is correlated with the incorporation of PEI in the interlamellar zones of PEEK crystals. The interaction parameter χ of PEEK/PEI blends is estimated by the equilibrium melting point depression. This gives the interaction density B = ?1.2 cal/cm³, and x = ?0.40 at 400°C. © 1993 John Wiley & Sons, Inc.     

High-temperature aging of Halar film. II. Analysis of melting behavior

Melting behavior of an experimental Halar film, a predominantly alternating 1:1 copolymer of ethylene (E) and chlorotrifluoroethylene (CTFE), has been studied. Differential scanning calorimetry (DSC) reveals single or double melting peaks, depending upon the thermal history. The lower-temperature melting peak T_m1 is produced only by the thermal treatment and shows a strong dependence on annealing time and temperature. On the basis of the DSC and x-ray data it can be suggested that T_m1 represents the melting of relatively small crystallites formed upon annealing. The higher-temperature melting peak T_m2 is always shown at 238°C. (Note: the specification for commercial Halar product is 240°C. The slightly lower melting temperature reported in this study is probably due to the fact that we are dealing with an experimental melt-processed material.) On the basis of the heating rate study we propose that Halar crystallizes with stable crystals (T_m2 = 238°C) regardless of the crystallization conditions, i.e., quenching, slow cooling, or even annealing. Crystals of Halar have a heat of fusion of approximately 35 cal/g or 146 kJ/kg. Detailed analysis of the melting behavior of Halar is presented.     

Thermostability of rat sarcoma M1 procollagen solutions,procollagen fibers and whole tissues

In close to equilibrium conditions (1° per 400 min), the DSC measurements demonstrated that the melting parameters of white rat sarcoma M1 procollagen equaled to T_m?=?34.4 °C and ΔT_m?=?2.7°, and the same parameters of fibers reconstructed from those solutions of procollagen were T_m?=?38.5 °C and ΔT?=?3.1°. These values were by 1.0° lower and 0.8° wider, and by 1.7° lower and 0.7° wider in comparison with the parameters of procollagen and fibers of healthy rat tissue, accordingly. The simultaneous increase in melting temperature and melting width, and a weak decrease in melting enthalpy demonstrated that sarcoma M1 procollagen had some defects. The considerable decrease by 7° in melting temperature and decrease in thermostability of procollagen fibrils in case of sarcoma M1 in comparison to the healthy norm gives a good prospective potential of using this approach as a quick DSC test to detect various sarcomas, including human sarcomas, by comparing the biopsy material or postsurgical tissues with the normal samples.

     

Novel cellulose derivatives. IV. Preparation and thermal analysis of waxy esters of cellulose

Cellulose esters with linear aliphatic acyl substituents ranging in size from C₁₂ (lauric acid) to C₂₀ (eicosanoic acid) were prepared in homogeneous solution (DMAc/LiCl) using a novel synthetic method based on the use of a mixed p-toluenesulfonic/carboxylic acid anhydride. The resulting waxy cellulose esters had a high degree of substitution (DS), between 2.8 and 2.9, and showed little degradation. Thermal analysis of these cellulose derivatives by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) revealed a series of transitions that represented motion by both ester substituents and cellulosic main chain. Broad crystallization and melting transitions attributed to side-chain crystallinity were observed in the range between −19 and +55°C; these side-chain T_m and T_c transition temperatures increased by 10°C per carbon atom of the ester substituent. The T_g of these derivatives increased linearly with increasing substituent size from 94°C for C₁₂ (cellulose laurate) to 134°C for C₂₀ (cellulose eicosanoate). Evidence of “main-chain” crystallization was not observed for these samples, except in the case of peracetylated C₁₂ and C₁₄ esters, which had T_m values of 96°C and 107°C, respectively. © 1996 John Wiley & Sons, Inc.     

Thermal stability and nonisothermal crystallization of short fiber-reinforced poly(ether ether ketone) composites

The thermal stability of a short carbon-fiber-reinforced PEEK composite was assessed by thermogravimetry and by a Rheometrics dynamic analyzer. The results indicated that holding for 10 min at 380°C was a suitable melting condition to avoid the thermooxidative degradation under air. After proving that the heating rate of 50°C/min can be used to evaluate the crystallinity, a heating stage was used to prepare nonisothermally crystallized specimens using cooling rates from 1 to 100°C/min after melting at 400°C for 3 or 15 min. The degree of crystallinity and the melting behavior of these specimens were investigated by DSC at a heating rate of 50°C/min. The presence of three or four regions indicated that the upper melting temperature, T_m, changed with the crystallization temperature. The first region with the highest T_m, which corresponded to the cooling rate of 1°C/min, can be associated with the crystallization in regime II. There was a second region where T_m decreased as the amount of crystals formed in regime II decreased with increasing cooling rate from 5 to 20°C/min. The third region, a plateau region, corresponded to regime III condition in which the crystals were imperfect. In the fourth region, the cooling was so fast that crystallization was incomplete during the cooling for the melting condition of 400°C for 15 min. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2225–2235, 1998     

Synthesis and characterization of wholly aromatic polyesters derived from 1-phenyl-2,6-naphthalene-dicarboxylic acid and aromatic diols

A series of new wholly aromatic polyesters was synthesized by melt polycondensation of 1-phenyl-2,6-naphthalenedicarboxylic acid (PNDA) and diacetates of various aromatic diols. The aromatic diols studied are hydroquinone (HQ), methylhydroquinone (MHQ), phenylhydroquinone (PHQ), (α-phenylisopropyl)hydroquinone (PIHQ), 2,6-naphthalenediol (2,6-ND), 1,4-naphthalenediol (1,4-ND), and 4,4′-biphenol (BP). These polyesters were characterized for their crystallinity, glass transition temperature (T_g), melting temperature (T_m), liquid crystallinity, and thermal stability. In general, crystallinity of the polyesters are very low and the T_g values of the polyesters range from 150 to 172°C depending on the structure of aromatic diols. All of the polymers formed nematic phases above their T_m or T_g. The polyesters derived from PHQ and PIHQ are soluble in chlorinated hydrocarbon solvents. The initial decomposition temperatures of the polyesters are above 400°C under N₂ atmosphere. © 1996 John Wiley & Sons, Inc.     

Ring-Opening Polymerization of the Cyclic Ester Amide Derived from Adipic Anhydride and 1-Amino-6-hexanol in Melt and in Solution

The ring-opening polymerization (ROP) of the cyclic ester amide (cEA) 5 (systematic name, 1-oxa-8-aza-cyclotetradecane-9,14-dione) - prepared from adipic anhydride and 1-amino-6-hexanol - in the melt at 165 °C and in solution at 100 °C and 120 °C with Bu₂Sn(OMe)₂ or Ti(OBu)₄ as initiator yields the alternating poly(ester amide) (PEA) 4 (systematic name, poly(5-(6-oxyhexylcarbamoyl)-pentanoate) with regular microstructure. Kinetic studies for different monomer-to-initiator ratios, different reaction media, initiators and temperatures reveal that the ROP is a first-order reaction with respect to the monomer. Under suitable polymerization conditions termination and transfer reactions are suppressed. The elementary chain growth reaction proceeds by a coordination insertion mechanism in analogy to the polymerization of lactones. By using monohydroxy- and bishydroxy-functional telechelic poly(ethylene oxide) and Sn(octoate)₂ as the initiating system poly(ethylene oxide)-block-poly(ester amide)s and poly(ester amide)-block-poly(ethylene oxide)-block-poly(ester amide)s are obtained. The poly(ester amide) 4 is a semicrystalline material with a melting point of 140 °C, the block copolymers are phase separated systems showing two melting points characteristic for the respective homopolymers.     

Benzocyclobutene in polymer synthesis. III. Heat-resistant thermosets based on Diels–Alder polymerization of a bisbenzocyclobutene and a bismaleimide

Several compatible mixtures of 2,2-bis[4-(N-4-benzocyclobutenyl) phthalimid-4-phenyl]hexafluoropropane (BCB) and 1,1′-(methylene di-4,1-phenylene)bismaleimide (BMI) were prepared according to the molar ratios (BCB : BMI): 1 : 1; 1 : 1.5; 1 : 3; 1.5 : 1. Complete compatibility of the mixtures was evidenced by a single initial T_g. All mixtures showed relatively low initial T_g's (61–70°C) and characteristic polymerization exotherms of benzocyclobutene-based systems (onset: 221–225°C; maximum: 257–259°C), providing an excellent processing window (ca. 155°C). The cured sample of the mixtures, pure BCB and BMI (250°C; N₂; 8 h) were subjected to comparative isothermal gravimetric analysis (ITGA). After 200 h at 650°F (343°C) in circulating air, the cured BMI sample retained only 3% of its original weight, whereas the mixtures of BCB and BMI exhibited thermo-oxidative stabilities similar to BCB (13–15% weight loss). A model compound was synthesized from the intimate mixture of N-phenylmaleimide and N-benzocyclobutenyl phthalimide in 63% yield. The ITGA results and isolation of the model Diels–Alder adduct render strong support to the conviction that Diels–Alder polymerization is indeed the predominant curing process in the BCB/BMI system.     

Synthesis and characterization of thermotropic liquid crystalline poly(ester imide)s

Two closely series of poly(ester imide)s had been synthesized by solution polycondensation of p‐phenylenebis(trimellitate) dianhydride with aliphatic diamines. The differential scanning calorimetry (DSC) traces of the most poly(ester imide)s exhibited two endotherms representing the solid state to anisotropic phase transition (T_m1) and the anisotropic to isotropic melt transition (T_m2), respectively. Observation under polarizing microscope and wide‐angle X‐ray diffraction (WAXD) measurements suggested that the anisotropic phase formed above the melting points (T_m1) had a smectic character. The thermogravimetric analyses (TGA) revealed that the thermal stabilities of the poly(ester imide)s were up to 350°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 211–218, 1999     

Phase equilibria in the GeSe2–SnSe system

The phase diagram of the system GeSe₂–SnSe is studied by means of X-ray diffraction, differential thermal analysis and measurements of the density and the microhardness of the material. There are no intermediate compounds in it, as well as regions of range of solid solutions at room temperature on the base of GeSe₂ and SnSe. There are two non-variant equilibria in the system: eutectic (where T _e=530±5°C and x _e= 40 mol% SnSe) and metaeutectic (where T _m=550±5°C and x _m=98 mol% SnSe).     

Effect of blending ratio and oligomer structure on the thermal transitions of stereocomplexes consisting of a D‐lactic acid oligomer and poly(L‐lactide)

Poly(lactic acid) (PLA) stereocomplexes have high potential as renewable materials for advanced polymer applications, mainly due to their high melting temperature (T_m, typically 230–240°C). The properties of PLA stereocomplexes consisting of linear high molar mass homopolymers have been studied extensively in the past, but the available information about the possibilities to affect the thermal properties of the stereocomplex by varying the structure of the blend components has not been sufficient. Novel stereocomplexes containing linear or star‐shaped D ‐lactic acid (D ‐LA) oligomers and high molar mass poly(L ‐lactide) (L‐ PLA) were thus prepared. The T_m and melting enthalpy (ΔH_m) of the racemic crystallites were found to depend strongly on both the blending ratio and the arm‐length of the D ‐lactic acid oligomer. The preparation method of the oligomers, i.e. step‐growth polymerization or ring‐opening polymerization (ROP), did not affect the T_m or ΔH_m of the blends significantly. Slightly higher ΔH_m values were, however, obtained, when linear oligomers were used. The results thus indicated that the T_m and ΔH_m of PLA stereocomplexes could be optimized, simply by selecting a D ‐LA oligomer having a suitable arm‐length and structure as the other blend component. The possibility to adjust the melting behavior of the stereocomplex blend is a significant advantage and could make PLA suitable for a wider range of products used at elevated temperatures. Copyright © 2010 John Wiley & Sons, Ltd.     

Biodegradable High-Density Polyethylene-like Material

We report a novel polyester material generated from readily available biobased 1,18-octadecanedicarboxylic acid and ethylene glycol possesses a polyethylene-like solid-state structure and also tensile properties similar to high density polyethylene (HDPE). Despite its crystallinity, high melting point (T_m=96 °C) and hydrophobic nature, polyester-2,18 is subject to rapid and complete hydrolytic degradation in in vitro assays with isolated naturally occurring enzymes. Under industrial composting conditions (ISO standard 14855-1) the material is biodegraded with mineralization above 95 % within two months. Reference studies with polyester-18,18 (T_m=99 °C) reveal a strong impact of the nature of the diol repeating unit on degradation rates, possibly related to the density of ester groups in the amorphous phase. Depolymerization by methanolysis indicates suitability for closed-loop recycling.     

The synthesis and liquid crystal transition temperatures of some weakly polar nematic methyl (E)-[trans-4-substituted-cyclohexyl]-allyl ethers

Abstract

We have introduced an oxygen atom and a carbon-carbon double bond with a trans-configuration (E) into the terminal alkyl chain of a wide variety of liquid crystalline cyclohexane derivatives to produce a variety of new methyl (E)-allyl ethers. The melting points and tendency to form smectic mesophases are often low, while nearly all of the compounds prepared exhibit a nematic phase. Thus, even two-ring derivatives can exhibit nematic phases over a wide temperature range (≤80°C), sometimes starting below room temperature (T _m≈10°C). Comparisons with the corresponding derivatives incorporating either just an oxygen atom or just a carbon-carbon double bond in the same position indicate that synergetic effects lead to broader nematic phases than would otherwise have been expected. Thus many of the new methyl (E)-allyl ethers exhibit nematic phases over a wider temperature range than the corresponding materials with an unsubstituted alkyl chain attached to the cyclohexyl ring. The new compounds are easily prepared from known starting materials. Many intermediates are themselves liquid crystalline. This allows investigation of the relationship between liquid crystal transition temperatures and the nature of the terminally substituted alkyl chain (for example, incorporating C[dbnd]C, OH, CO₂C₂H₅ and OCH₃ groups).