Hydrogels of chemically cross-linked and organ-metallic complexed interpenetrating PEG networks

The aim of the present work was to prepare a well-defined hydrogel of chemically cross-linked and organ-metallic complexed interpenetrating PEG networks. The hydrogel was synthesized via the reaction of copper(I)- catalyzed 1,3-dipolar azide-alkyne cycloaddition(CuA AC) with poly(ethylene glycol)-dopamine(PEG-DA)("Click Chemistry") followed by complexation with Fe~(3+) ions to crosslink the polymeric network. The chemical composition and morphology of the resulting hydrogels were characterized by Fourier transform infrared spectroscopy(FTIR), ~1H-NMR and scanning electron microscopy(SEM). Swelling ratio, mechanical strength, conductivity, and degradation behaviors of the hydrogels were also studied. The effect of the polymer chain length on properties of hydrogels was explored. The compressive strength of hydrogels could reach as high as 13.1 MPa with a conductivity of 2.2 × 10~(-5) S·cm~(-1). The hydrogels also exhibited excellent thermal stability even at a temperature of 300 °C, whereas degradation of the hydrogel after 7 weeks was observed under a physiological condition. In addition, the hydrogel exhibited a good biocompatibility based on its in vivo performance through an in vivo subcutaneous implantation model. No inflammation and no obvious abnormality of the surrounding tissue were observed when the hydrogel was subcutaneously implanted for 2 weeks. This work is a step towards creating a new pathway to synthesize hydrogels of interpenetrating networks which could be of important applications in the future research.     

RADIATION INDUCED ACRYLAMIDE/CITRIC ACID HYDROGELS AND THEIR SWELLING BEHAVIORS

Citric acid (CAc) moieties containing acrylamide (AAm) hydrogels were prepared by gamma irradiation of their aqueous solutions. A possible polymerization and crosslinking mechanism for acrylamide/citric acid (AAm/CAc) hydrogels is proposed. The effects of irradiation dose and citric acid content on swelling behavior were investigated. Swelling took place in water at 25°C and was followed gravimetrically. Incorporation of a relatively low amount of citric acid to acrylamide hydrogel increased its swelling up to 950% from 700%. The diffusion of water into AAm/CAc hydrogels was found to be a non-Fickian type. Diffusion coefficients of AAm/CAc hydrogels found as 5 × 10^?7? 10 × 10^?7 cm² sec^?1. It has also been found that the number average molar mass between crosslinks is increased with the CAc content and decreased with irradiation dose.     

含金刚烷基的N-异丙基丙烯酰胺共聚物水凝胶的制备和性能研究

合成了含金刚烷基的甲基丙烯酸金刚烷酯(AdMA)疏水单体,并通过与N-异丙基丙烯酰胺(NIPAM)共聚,制备了温敏性的(P(NIPAM-co-AdMA))共聚物水凝胶.用傅里叶变换红外光谱仪(FTIR)表征了凝胶的化学结构,用环境扫描电镜(ESEM)对凝胶断层结构的形貌进行了观察,用DSC测试了凝胶的体积相转变温度(LCST),并研究了共聚水凝胶的溶胀性能.结果表明,共聚物水凝胶的LCST能够高效地通过改变疏水单体的含量来调节,在实验所考察的范围内,LCST随AdMA含量的增加而线性降低;疏水单体的含量对凝胶的孔洞结构和溶胀性能存在一最优值,在最优的单体配比下,水凝胶具有均匀规整的大孔结构和超快的响应速率.如疏水单体含量为3%(AdMA∶NIPAM=3%)的共聚物水凝胶具有如渔网般均匀的多孔结构,当发生去溶胀时,在5min内就可以失去92%的水,不到10min的时间就可以完全达到去溶胀平衡,水保留率在4%以下.     

Synthesis,characterization, and evaluation of enzymatically degradable poly(N‐isopropylacrylamide‐co‐acrylic acid) hydrogels for colon‐specific drug delivery

The enzymatically degradable poly(N‐isopropylacrylamide‐co‐acrylic acid) hydrogels were prepared using 4,4^′‐bis(methacryloylamino)azobenzene (BMAAB) as the crosslinker. It was found that the incorporated N‐isopropylacrylamide (NIPAAm) monomer did not change the enzymatic degradation of hydrogel, but remarkably enhanced the loading of protein drug. The hydrogels exhibited a phase transition temperature between 4°C (refrigerator temperature) and 37°C (human body temperature). Bovine serum albumin (BSA) as a model drug was loaded into the hydrogels by soaking the gels in a pH 7.4 buffer solution at 4°C, where the hydrogel was in a swollen status. The high swelling of hydrogels at 4°C enhanced the loading of BSA (loading capability, ca. 144.5 mg BSA/g gel). The drug was released gradually in the pH 7.4 buffer solution at 37°C, where the hydrogel was in a shrunken state. In contrast, the enzymatic degradation of hydrogels resulted in complete release of BSA in pH 7.4 buffer solution containing the cecal suspension at 37°C (cumulative release: ca. 100 mg BSA/g gel after 4 days). Copyright © 2008 John Wiley & Sons, Ltd.     

Poly(N‐isopropylacrylamide)‐based comb‐type grafted hydrogel with rapid response to blood glucose concentration change at physiological temperature

A new type of glucose‐responsive hydrogel with rapid response to blood glucose concentration change at physiological temperature has been successfully developed. The polymeric hydrogel contains phenylboronic acid (PBA) groups as glucose sensors and thermo‐responsive poly (N‐isopropylacrylamide) (PNIPAM) groups as actuators. The response rate of the hydrogel to environmental glucose concentration change was significantly enhanced by introducing grafted poly(N‐isopropylacrylamide‐co‐3‐acrylamidophenylboronic acid) [poly(NIPAM‐co‐AAPBA)] side chains onto crosslinked poly(NIPAM‐co‐AAPBA) networks for the first time. The synthesized comb‐type grafted poly(NIPAM‐co‐AAPBA) hydrogels showed satisfactory equilibrium glucose‐responsive properties, and exhibited much faster response rate to glucose concentration change than normal type crosslinked poly(NIPAM‐co‐AAPBA) hydrogels at physiological temperature. Such glucose‐responsive hydrogels with rapid response rate are highly attractive in the fields of developing glucose‐responsive sensors and self‐regulated drug delivery systems. Copyright © 2008 John Wiley & Sons, Ltd.     

Effect of Different Composition on Particle Size Chitosan-PMAA-PNIPAM Hydrogel

Chitosan-based (chitosan-poly(methacrylic acid)-poly(N-isopropylacrylamide) [Cs-PMAA-PNIPAM] copolymer hydrogels were synthesized by free radical emulsion polymerization to study the effect of different composition of monomer on hydrogel particle size. Chitosan usually applied for medical use such as drug delivery due to its biodegradability, bio-compatibility, and non-toxicity properties. Co-polymerized chitosan with MAA and NIPAM is an improvement of chitosan gel to be more responsive to the environment of human body included different pH, temperature, ionic strength, electric field, and enzyme activities. Small size of the particles is particularly important to ensure the particles reach the target site especially as a drug delivery. A full factorial experimental design (2³) was employed to identify which factors influenced most on the particle size. The design considered three factors which is amount of MAA, NIPAM and N,N’-Methylenebisacrylamide (MBA) while particle size are chosen as the responses of the variation on each composition. Particle size distribution was measured by laser diffractionin wet condition. From the design of experiment, NIPAM shows the main factor affected the particle size. However combination of the others factors also contributed on the whole size of the hydrogel.     

Smart bilayer polymer reactor with cascade/non-cascade switching catalyst characteristics

In this work, a new method is proposed to meet the challenge of preparing new catalysts with cascade/non-cascade switching catalytic property. Inspired from “soft” characteristics and divisional isolation function in natural biological systems, this objective was accomplished by developing a new class of hydrogels made of two unique functional layers with different temperature responses where each may self-govern coupled processes at a specific temperature. This hydrogel polymer reactor exhibited almost no catalytic activity at low-temperature range (<37 °C) as both channels of bilayer hydrogel polymer catalyst were closed. At modest temperatures (between 37 °C and 50 °C), the first step of the tandem reaction (the hydrolysis of p-nitrophenyl acetate (NPA)) showed significant reactivity that arises from the relaxing of the weak polymer complexes in the hydrogel layer. This enabled NPA the access to the acidic catalytic active center of the hydrogel. At range of higher temperatures (>50 °C), the hydrogel catalytic polymer reactor further exhibited significant efficiency towards the hydrolysis reaction of NPA as well as the reduction of the intermediate product p-nitrophenol (NP). This mainly resulted from the opening of both the weak polymer complexes and the stronger polymer complexes hydrogel layers, allowing entrance to both the acidic catalytic active center and the metal nanoparticles active center. As a result, the novel hydrogel polymer reactor could be used to control cascade/non-cascade catalysis reactions. This new protocol enables efficient control of switchable tandem reactions, inspiring for difficulty to control tandem catalytic reactors.     

Diffusion and transfer of antibody proteins from a sugar-based hydrogel

Diffusion of antibody protein from hydrogel films and hydrogel encapsulated in a microcapillary was studied. Thin hydrogel films were formed by crosslinking 6-acryloyl-B-O-methylgalactoside withN,N’-methylene-bis-acrylamide and the diffusive transport of monoclonal antimouse IgG-FITC into and out of the hydrated films was measured. Diffusion coefficients in 2 and 4% crosslinked hydrogel films were measured. The measured diffusion constants determined for IgG in both the 2 and 4% hydrogel films were comparable to the free diffusion of IgG in bulk water (D _mean ∼ 10^-7cm²/s). In addition, 2% crosslinked hydrogels were prepared in a capillary tube and the transport of antimouse IgG-FITC into and out of the hydrated hydrogel was measured. Kinetic analysis indicated that the protein transport through the capillary hydrogel was faster than would be expected for a simple diffusion process. Finally, by utilizing the diffusion of antibody from the capillary hydrogel, transfer of antibody to a silica surface was demonstrated. A capillary hydrogel loaded with antimouse IgG-FITC was used to transfer the protein to a silica surface forming a 30-μm spot of antibody, which was imaged using fluorescence microscopy. These results may lead to the development of a nonlithographic method of patterning antibodies on surfaces for use in integrated microimmunosensors.     

Preparation and characterization of pH- and temperature-responsive semi-IPN hydrogels of carboxymethyl chitosan with poly (<Emphasis Type="Italic">N</Emphasis>-isopropyl acrylamide) crosslinked by clay

A new kind of pH- and temperature-responsive semi-interpenetrating polymer network hydrogel based on linear carboxymethylchitosan (CMCS) and poly (N-isopropylacrylamide) (PNIPA) crosslinked by inorganic clay was prepared. The pH-and temperature-responsive behaviors, the deswelling kinetics, and the mechanical properties of the hydrogel were investigated. The hydrogels exhibited a volume phase transition temperature around 33 °C with no significant deviation from the conventional PNIPA hydrogels. The results of the influence of pH value on the swelling behaviors showed that the minimum swelling ratios of the hydrogels appeared near the isoelectric point (IEP) of CMCS, and when pH deviated from the IEP, the hydrogels behaved as polycations or polyanions. The novel hydrogels had much higher response rate than the conventional CMCS/PNIPA hydrogels. Moreover, the semi-IPN hydrogels crosslinked by clay could be elongated to more than 800% and the elongation could be recovered almost completely and instantaneously.     

Synthesis and characterization of hydrogels containing redox-responsive 2,2,6,6-tetramethylpiperidinyloxy methacrylate and thermoresponsive N-isopropylacrylamide

Smart hydrogels containing 2,2,6,6-tetramethylpiperidinoxy methacrylate (TEMPO) and N-isopropylacrylamide (NIPAM) that undergo reversible redox behavior are prepared and investigated. Several polymer networks are first prepared by free-radical copolymerization of varying amounts of TEMPO, NIPAM, and a crosslinker (diethylene glycol diacrylate) and subsequently swelled with water to lead to hydrogels. In order to investigate the effects of the redox activity of TEMPO units and of the lower critical solution temperature of NIPAM on the hydrogel properties, a study of the swelling ratio of the polymer networks in distilled water at different temperatures is performed for the two forms of TEMPO, the reduced (TEMPO) and oxidized (TEMPO⁺) one. Moreover, the rheological properties are also measured for both hydrogel forms. Finally, the encapsulation abilities of the oxidized hydrogels are demonstrated via electrostatic interactions between positively charged TEMPO⁺ units and negatively charged guest molecules, supporting future application of our system in the biomedical and environmental fields.     

Preparation of thermosensitive,calix[4]arene incorporated P(NIPAM‐co‐HBCalix) hydrogel as a reusable adsorbent of nickel(II) ions

A calix‐conjugated thermo‐responsive hydrogel containing 15% tetra(5‐hexenyloxy)‐p‐tert‐butylcalix[4]arene (HBCalix), P(NIPAM‐co‐HBCalix), was used to remove nickel(II) ions from water. Both thermo‐sensitive properties and the Ni²⁺‐adsorption capabilities of the prepared P(NIPAM‐co‐HBCalix) hydrogels are investigated. Introduction of the monomer HBCalix considerably enhanced the adsorption of Ni²⁺ onto the hydrogel by chelation between hexenyloxy groups and metal ion. When HBCalix units capture Ni²⁺ and forms HBCalix/Ni²⁺ host–guest complexes, the lower critical solution temperature of the hydrogel shifts to a higher temperature due to both the repulsion between charged HBCali/Ni²⁺ groups and the osmotic pressure within the hydrogel. Adsorption studies were carried out by varying contact time, counter ion and initial concentration of Ni²⁺. The evaluation of adsorption properties showed that the hydrogel exhibited better correlation with Langmuir isotherm model. P(NIPAM‐co‐HBCalix) could be used repeatedly with little loss in adsorption capacity by simply changing the environmental temperature. This kind of ion‐recognition hydrogel is promising as a novel adsorption material for adsorption and separation of Ni²⁺ ions. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2401–2408     

Swelling and drug release properties of acrylamide/carboxymethyl cellulose networks formed by gamma irradiation

Hydrogels based on acrylamide monomer (AM) and different ratios (5–20 wt%) of carboxymethyl cellulose (CMC) were synthesized by gamma irradiation. The hydrogels were characterized in terms of gel content, swelling and drug release characters. The effect of temperature and pH on the degree of swelling was also studied. The results showed that the gel fraction of AM/CMC hydrogels decreases greatly with increasing the contents of CMC in the initial feeding solution. The kinetic study showed that the swelling of all the hydrogels tends to reach the equilibrium state after 5 h. However, the swelling of AM/CMC hydrogels was greater than the hydrogel based on pure AM. On the other hand, it was found that the swelling of all the hydrogels changes within the temperature range 30–40 °C and within the pH range 4–8. The AM/CMC hydrogels was evaluated for the possible use in drug delivery systems. In this respect, the release properties of methylene blue indicator, as a drug model, was investigated. It was found that the percentage release from the hydrogels increase with time to reach ～80% after 3 h at pH of 2 compared to ～100% at pH of 8.     

Synthesis and properties of poly(acrylamide‐co‐acrylic acid)/polyacrylamide superporous IPN hydrogels

Poly(acrylamide‐co‐acrylic acid)/polyacrylamide [P(AM‐co‐AA)/PAM] hydrogel with superporous and interpenetrating network (IPN) structure was prepared by a prepolymerization reaction and a synchronous polymerization reaction and frothing process. Scanning electron microscope (SEM) images show that the resultant hydrogel possesses abundant interconnected pores. DSC indicates that the porous structure enhances the swelling ratio and reduces the interaction between water and the hydrogel. In contrast, the IPN by PAM decreases water absorbency and enhances water retentivity. It is found that a superporous stucture in the hydrogel increases the equilibrium swelling ratio and decreases the compressive strength of the hydrogel. On the other hand, the increase in AM oligomer (oligo‐AM) amount decreases the equilibrium swelling ratio and improves the compressive strength of the hydrogel. Therefore, the two‐steps synthesis method can be used to construct a hydrogel with superporous and IPN structure. The swelling and mechanical properties of the hydrogel can be improved effectively. Copyright © 2008 John Wiley & Sons, Ltd.     

Photoisomerizable and Thermoresponsive N‐isopropylacrylamide–Surfmer Copolymer Hydrogels Prepared upon Electrostatic Self‐Assembly of an Azobenzene Bolaamphiphile

Photoreactive and thermoresponsive N‐isopropylacrylamide (NIPAM)–surfmer copolymer hydrogels containing 4,4′‐di(6‐sulfato‐hexyloxy)azobenzene (DSHA) dianions are described. The functional hydrogels are obtained in a two steps. First a micellar aqueous solution of (11‐(acryloyloxy)undecyl)trimethylammonium bromide (AUTMAB) and NIPAM is exposed to ⁶⁰Co‐gamma irradiation, and a thermoresponsive copolymer gel is obtained. Second, DSHA is included by shrinking the gel at 50 °C and subsequent reswelling in an aqueous solution of DSHA disodium salt at 20 °C. Reswelling is accompanied by electrostatic adsorption of DSHA dianions at the positively charged AUTMAB headgroups replacing the bromide ions. Gels containing trans‐DSHA are transparent yellow at room temperature (λ_max = 370 nm), while gels containing cis‐rich DSHA are orange (λ_max = 460 and 330 nm). Energy dispersive X‐ray measurements indicate that 41% of the bromide ions are exchanged if trans‐DSHA is used for adsorption, and only 7.5% if cis‐DSHA is used. The incorporation of DSHA lowers the lower critical solution temperature (LCST) from 34 to 32 °C. Below the LCST, DSHA can be switched from the trans‐ to the cis‐rich state and vice versa upon irradiation with UV (λ = 366 nm) or visible light (λ ≥ 450 nm). Above the LCST no photoreaction takes place.     

Electroconductive Hydrogels: Electrical and Electrochemical Properties of Polypyrrole‐Poly(HEMA) Composites

Composites of inherently conductive polypyrrole (PPy) within highly hydrophilic poly(2‐hydroxyethyl methacrylate)‐based hydrogels (p(HEMA)) have been fabricated and their electrochemical properties investigated. The electrochemical characteristics observed by cyclic voltammetry suggest less facile reduction of PPy within the composite hydrogel compared to electropolymerized PPy, as shown by the shift in the reduction peak potential from ?472 mV for electropolymerized polypyrrole to ?636 mV for the electroconductive composite gel. The network impedance magnitude for the electroconductive hydrogel remains quite low, ca. 100 Ω, even upon approach to DC, over all frequencies and at all offset potentials suggesting retained electronic (bipolaronic) conductivity within the composite. In contrast, sustained application of +0.7 V (vs. Ag/AgCl, 3 M Cl^?) for typically 100 min. (conditioning) to reduce the background amperometric current to <1.0 μA, resulted in complete loss of electroactivity. Nyquist plots suggest that sustained application of such a modest potential to the composite hydrogel results in impedance characteristics that resembles p(HEMA) without evidence of the conducting polymer component. PPy composite gels supported a larger ferrocene monocarboxylate diffusivity (D_appt=7.97×10^?5 cm² s^?1) compared to electropolymerized PPy (D_appt=5.56×10^?5 cm² s^?1), however a marked reduction in diffusivity (D_appt=1.01×10^?5 cm² s^?1) was observed with the conditioned hydrogel composite. Cyclic voltammograms in buffer containing H₂O₂ showed an absence of redox peaks for electrodes coated with PPy‐containing membranes, suggesting possible chemical oxidation of polypyrrole by the oxidant     

Effect of Pore-Forming Agent Type on Swelling Properties of Macroporous Poly(N-[3-(dimethylaminopropyl)]-methacrylamide-co-acrylamide) Hydrogels

Macroporous poly(N-[3-(dimethylaminopropyl)]methacrylamide-co-acrylamide) [P(DMAPMA-co-AAm)] hydrogels were prepared by free-radical crosslinking copolymerization of corresponding monomers in water using two different pore-forming agents such as hydroxypropyl celluose (HPC) and poly(ethylene glycol) (PEG). The effect of these pore-forming agents on the volume phase transition temperature (VPT-T), interior morphology and swelling/deswelling kinetics of the P(DMAPMA-co-AAm) hydrogels was investigated. Scanning electron micrographs revealed that the interior network structure of the hydrogel matrix became more porous due to the presence of HPC or PEG pore-forming agents. The more porous matrix provided numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to the external stimuli. Particularly, due to its unique macroporous structure, the PEG-modified hydrogel showed a tremendously faster response to the external temperature changes during deswelling process and the swelling process at 22°C.     

THERMOPROCESSIBLE HYDROGELS. I. SYNTHESIS AND PROPERTIES OF POLYACRYLAMIDES WITH PERFLUOROALKYL SIDE CHAINS

ABSTRACT

Copolymers composed of acrylamide (AM), N,N-dimethylacrylamide (DMAM), N-isopropylacrylamide (NIPAM) and 2-(N-ethyl-perfluorooctanesulfonamido) acrylamide (FOSA) were synthesized by free radical polymerization. The chemical structure of the resulting polymers was characterized with NMR spectroscopy and thermal properties were measured by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). ¹H-NMR spectra of the copolymers of NIPAM with FOSA showed that FOSA was incorporated quantitatively. The glass transition temperature (T_g) of the copolymers and the terpolymers decreased with increasing FOSA content. The T_gs, however, were higher than predicted for a random copolymer by the Fox equation, which was attributed to microphase separation of the hydrophobic, fluorinated species. Copolymers of AM and FOSA became discolored above 180°C due to formation of cyclic imide and nitrile moieties through cyclization or dehydration of amide groups. The equilibrium water sorption of the copolymers decreased with increasing FOSA content, but increasing FOSA suppressed the water desorption kinetics. Water sorption and thermal stability were improved by terpolymerization of AM, NIPAM, DMAM and FOSA.     

A novel ion‐imprinted hydrogel for recognition of potassium ions with rapid response

A novel ion‐imprinted strategy is developed for synthesizing responsive hydrogels with rapid response to potassium ions. With potassium ions as templates, ion‐imprinted poly(N‐isopropylacrylamide‐co‐benzo‐15‐crown‐5‐acrylamide) (P(NIPAM‐co‐B15C5Am)) hydrogels are synthesized with 15‐crown‐5 crown ethers mounted on the polymer networks in pairs; therefore, it is very easy and fast for the crown ethers to capture potassium ions again by their Venus flytrap action and form stable 2:1 “host–guest” complexes with potassium ions in the ion‐recognition process. As a result, the response rate of the ion‐imprinted hydrogels to potassium ions is significantly faster than that of normal P(NIPAM‐co‐B15C5Am) hydrogels in which 15‐crown‐5 crown ethers are randomly pendent on the polymeric networks. Copyright © 2010 John Wiley & Sons, Ltd.     

Effect of pre‐treatment of sugarcane bagasse on the cellulose solution and application for the cellulose hydrogel films

Sugarcane bagasse was used as a cellulose resource, and the transparent cellulose hydrogel films were obtained from the purified cellulose by phase inversion process without chemical cross‐linking, when the dissolved cellulose in lithium chloride/N,N‐dimethyl acetamide was transformed into the solid film. On these processes, bagasse was pre‐treated by 10 wt% sodium hydroxide in the absence and presence of bleaching of 10 vol% sodium hypochlorite (NaOCl) solution in order to obtain cellulose fibers. Here, the bleaching temperature was varied from 40 to 50°C. The effect of pre‐treatment conditions on the resultant cellulose solution and hydrogel films was investigated. It was seen that strong bleaching removed most of lignin component from the bagasse. However, viscosity and size exclusion chromatogram of the cellulose indicated that this operation decreased average molecular weight of the cellulose fibers from 2.1 × 10⁶ to 4.8 × 10⁵. These property changes of fibers also caused increase of water content and weakening of mechanical strength of the resultant hydrogels. In addition, scanning probe microscopy in wet state revealed that the porous fiber network structure in the hydrogel was greatly influenced by bleaching with NaOCl. The average pore size of fiber network was decreased from 8.1 to 5.9 nm as the NaOCl treatment was at 50°C, because of expanded fibers in the swollen hydrogel. Copyright © 2016 John Wiley & Sons, Ltd.     

Organic–inorganic hybrid hydrogels involving poly(N‐isopropylacrylamide) and polyhedral oligomeric silsesquioxane: Preparation and rapid thermoresponsive properties

3‐Acryloxypropylhepta(3,3,3‐trifluoropropyl) polyhedral oligomeric silsesquioxane (POSS) was synthesized and used as a modifier to improve the thermal response rates of poly(N‐isopropylacrylamide) (PNIPAM) hydrogel. The radical copolymerization among N‐isopropylacrylamide (NIPAM), the POSS macromer and N,N′‐methylenebisacrylamide was performed to prepare the POSS‐containing PNIPAM cross‐linked networks. Differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) showed that the POSS‐containing PNIPAM networks displayed the enhanced glass transition temperatures (T_g's) and improved thermal stability when compared with plain PNIPAM network. The POSS‐containing PNIPAM hydrogels exhibited temperature‐responsive behavior as the plain PNIPAM hydrogels. It is noted that with the moderate contents of POSS, the POSS‐containing PNIPAM hydrogels displayed much faster response rates in terms of swelling, deswelling, and re‐swelling experiments than plain PNIPAM hydrogel. The improved thermoresponsive properties of hydrogels have been interpreted on the basis of the formation of the specific microphase‐separated morphology in the hydrogels, that is, the POSS structural units in the hybrid hydrogels were self‐assembled into the highly hydrophobic nanodomains, which behave as the microporogens and promote the contact of PNIPAM chains and water. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 504–516, 2009