TiO2/Bi2O3纳米复合体的制备及可见光催化产氢性能

首先采用相分离的水解-溶剂热法制备了Bi₂O₃纳米粒子,然后利用简单的湿化学法在Bi₂O₃表面负载不同比例的TiO₂纳米颗粒,进而得到TiO₂/Bi₂O₃纳米复合体。通过气氛调控的表面光电压谱(SPS)等测试表明,表面负载适量的TiO₂后能够提高Bi₂O₃光生电荷分离。可见光催化产氢和降解污染物测试结果进一步证明,表面负载适量的TiO₂后可显著提高其可见光催化活性,其中Ti/Bi摩尔比为7%时具有最高的光催化活性。这主要归因于TiO₂具有较为合适的导带能级位置,可以接收Bi₂O₃在可见光激发下所产生的高能级电子,从而抑制光生电子-空穴对复合,并且维持了高能级电子较高的还原能力。     

Photocatalytic degradation of amoxicillin by carbon quantum dots modified K2Ti6O13 nanotubes: Effect of light wavelength

Novel carbon quantum dots modified potassium titanate nanotubes (CQDs/K₂Ti₆O₁₃) composite was synthesized and exhibited high photocatalytic activity for degradation of amoxicillin under UV and visible lights with nine wavelengths. Better amoxicillin removal was achieved at lower wavelength irradiation due to its higher photo energy.     

A novel method for the preparation of Bi4Ti3O12 nanoparticles in w/o microemulsion

Nanometer-sized Bi₄Ti₃O₁₂ particles have been prepared by chemical reaction of bismuth nitrate pentahydrate, titanium sulfate and ammonia solution in a reverse microemulsion system consisting of water, OP (P-octyl polyethylene glycol phenylether, non-ionic surfactant), n-butanol (co-surfactant), and cyclohexane (oil). Precursor hydroxides precipitated in the droplets of water-in-oil (w/o) microemulsion were calcined at 800 °C for 4 h to form Bi₄Ti₃O₁₂ nanoparticles. The samples were investigated with X-ray diffraction (XRD), transmission electron microscopy (TEM), fourier transform infrared spectrophotometer (FT-IR) and ultraviolet visible spectrophotometer (UV–vis). It was found that the as-prepared Bi₄Ti₃O₁₂ nanoparticles had small particle sizes (35 nm), high crystallinity, narrow size distributions and strong light absorption properties not only in the ultraviolet light but also in the visible light region.     

Synthesis of titania and titanate nanomaterials and their application in environmental analytical chemistry

TiO₂ nanoparticles and H₂Ti₂O₅·H₂O, Na₂Ti₂O₄(OH)₂ nanotubes were synthesized by solvothermal method and their applications in the degradation of active Brilliant-blue (KN-R) solution were investigated. The experimental results revealed that the synthesized TiO₂ nanoparticles had a good crystallinity and a narrow size distribution (about 4–5 nm); the obtained H₂Ti₂O₅·H₂O, Na₂Ti₂O₄(OH)₂ were tubelike products with an average diameter of 20–30 and 200–300 nm length. The three catalysts we synthesized had some hydroxyl groups and the maximum absorption boundaries of the samples were all red-shifted, which indicated the samples had a promising prospect in photocatalysis.

The results of the photocatalytic experiments indicated that the photocatalytic activity of the samples was: TiO₂ > H₂Ti₂O₅·H₂O > Na₂Ti₂O₄(OH)₂, which was in good accordance with the fact of FTIR and UV–vis absorption spectra. The formation mechanism of these nanostructures was also discussed.     

Bi2Sn2O7 nanoparticles attached to SnO2 nanowires and used as catalysts

We introduce a simple method of synthesizing SnO₂ nanowire-Bi₂Sn₂O₇ nanoparticle composites based on the principle that SnO₂ nanowires can be grown by using Bi as catalysts. A mixture of Bi and Sn powders was thermally evaporated, and the effects of growth temperature on the morphology and structure of the products were investigated. We obtained Bi₂Sn₂O₇-tipped SnO₂ nanowires at 700 °C through a vapor–liquid–solid (VLS) process, whereas particle-free SnO₂ nanowires were produced at higher temperatures. We have investigated the oxygen sensing properties of the as-synthesized product.     

Tunable Synthesis of Core-shell α-Fe2O3/TiO2 Composite Nanoparticles and Their Visible-light Photocatalytic Activity

Uniform α-Fe₂O₃/amorphous TiO₂ core-shell nanocomposites were prepared via a hydrolysis method and α-Fe₂O₃/anatase TiO₂ core-shell nanocomposites were obtained via a post-calcination process. The structure and morphology of the products were characterized by powder X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy and scanning electron microscopy. Amorphous TiO₂ nanoparticles with diameters of ten to several tens nanometer were formed on the surface of α-Fe₂O₃ nanoparticles and the coverage density of the secondary TiO₂ nanoparticles in the composite can be controlled by varying the concentration of Ti(BuO)₄ in the ethanol solution. The visible-light photocatalytic properties of different products towards Rhodamine B(RhB) were investigated. The results show that the α-Fe₂O₃/amorphous TiO₂ exhibits a good photocatalytic property owing to the extension of the light response range to visible light and the efficient separation of photogenerated electrons and holes between α-Fe₂O₃ and amorphous TiO₂.     

Characterizations and photocatalytic activity of nanocrystalline La1.5Ln0.5Ti2O7 (Ln = Pr, Gd, Er) solid solutions prepared via a polymeric complex method

Nanocrystalline La_1.5Ln_0.5Ti₂O₇ (Ln = Pr, Gd, Er) solid solutions were prepared by a polymeric complex method. The samples were characterized by X-ray diffraction (XRD) analysis, transmission electron microscopy (TEM), UV–vis diffuse reflectance spectra (DRS), energy dispersive X-ray spectrum (EDS), thermogravimetric analyses (TGA) and differential thermal analyses (DTA). The photocatalytic activity of La_1.5Ln_0.5Ti₂O₇ (Ln = Pr, Gd, Er) was evaluated by the photocatalytic degradation of methyl orange (MO). La_1.5Gd_0.5Ti₂O₇ showed the best photocatalytic activity and it was supposed that the half-filled electronic configuration of Gd³⁺ can promote charge transfer and enhance the photocatalytic activity. The difference in the photocatalytic activity observed for La_1.5Ln_0.5Ti₂O₇ (Ln = La, Pr, Gd, Er) can be related to the different Ln 4f shell.     

Electrochemical and gas-phase photocatalytic performance of nanostructured TiO2(B) prepared by novel synthetic route

Nanostructured phase pure TiO₂(B) with microfibrous morphology was synthesized by newly developed protocol employing amorphous TiO₂ as a precursor. Compared to traditional syntheses from K₂Ti₄O₉, the new product exhibited better electrochemical performance and stability. Cyclic voltammetry of Li-insertion into the TiO₂(B) evidences a pseudocapacitive faradaic process of Li accommodation which is basically different from the diffusion-controlled lithium storage in anatase or rutile. The presence of two pairs of peaks in cyclic voltammogram with formal potentials of ca. 1.5 and 1.6 V is specific for TiO₂(B). This enables to use cyclic voltammetry for identification of this phase in a broad palette of TiO₂ materials of various origin.

The photocatalytic activity of TiO₂(B) in a gas phase was evaluated using the total oxidation of propane with oxygen and the photocatalytic reduction of NO to N₂ in an oxygen rich gas mixture. For the total oxidation of propane in the gas mixture containing 300 ppm propane and 20% oxygen, the reaction rates per 1 m²/g of the BET surface area of the catalyst for TiO₂(B) prepared by our protocol and Hombifine N (anatase, S_BET = 300 m²/g) are comparable. For the photocatalytic NO reduction to N₂ in an atmosphere containing 20% oxygen the ratio of quantum yields for TiO₂(B) and Hombifine N was found to be 0.08, which is roughly equivalent to the ratio of their BET surface areas (0.09), despite different phase composition of both materials. In comparison with the standard catalyst our material exhibited higher selectivity in the reduction of NO to N₂.     

富含光诱导氧空位Bi12O17Br2的制备及其高效光催化固氮性能

采用一步水热法制备了Bi₁₂O₁₇Br₂光催化剂,其平均微片尺寸为1.2μm,比表面积约为29 m²·g^-1。Bi₁₂O₁₇Br₂的禁带宽度为2.42 eV,能够响应可见光。值得注意的是,在光照条件下Bi₁₂O₁₇Br₂表面能够产生氧空位;光诱导氧空位不仅能促进氮气在催化剂表面的吸附,而且对吸附的氮气分子的活化起到至关重要的作用。实验结果表明在可见光照射下,Bi₁₂O₁₇Br₂光催化剂上的氨生成速率为337.6μmol·g^-1·h^-1。在可见光的驱动下,Bi₁₂O₁₇Br₂光催化剂能够实现氮气与水反应生成氨的过程。     

脉冲沉积制备Cu_2O/TiO_2纳米管异质结的可见光光催化性能

在用阳极氧化法制备有序排列TiO2纳米管阵列薄膜的基础上,引入脉冲沉积工艺,成功实现了均匀、弥散分布的Cu2O纳米颗粒修饰改性TiO2纳米管阵列,形成Cu2O/TiO2纳米管异质结复合材料.利用场发射扫描电镜(FESEM)、场发射透射电镜(FETEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外-可见漫反射光谱(UV-Vis DRS)对样品进行表征,重点研究了Cu2O/TiO2纳米管异质结的光电化学特性和对甲基橙(MO)的可见光催化降解性能.结果表明,Cu2O纳米颗粒均匀附着在TiO2纳米管阵列的管口和中部位置,所制备的Cu2O/TiO2纳米管异质结具有高效的可见光光催化性能;在浓度为0.01 mol?L-1的CuSO4溶液中制得的Cu2O/TiO2纳米管异质结表现出最好的电化学特性和光催化性能;另外,对Cu2O纳米颗粒影响光催化活性的机理进行了讨论.     

超临界水热极速合成异质结构H4SiW12O40/Bi2WO6光催化剂及其脱氮性能

采用超临界水热合成方式极速合成一种H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂,通过X射线衍射(XRD)、场发射扫描电子显微镜(SEM)、透射电子显微镜(TEM)、比表面积及孔隙度(BET)测定对所合成催化剂的结构和性质进行了考察,并以吡啶含量为15 mg/g的模拟油对光催化剂的脱氮效果进行评价。结果表明,该光催化剂为二维纳米片自组装成的三维球状结构,其中,H_4SiW_(12)O_(40)与Bi_2WO_6不是简单的固载关系而是在超临界水热条件下生成一种新的晶相,正是由于这种晶相的存在,使得H_4SiW_(12)O_(40)牢固固载在Bi_2WO_6光催化剂本体上的同时,对光生载流子进行了有效疏导,提升了H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂的使用寿命和光催化活性。本研究针对光催化剂制备周期与晶形发育的矛盾,将超临界水热技术与光催化剂模板导向合成技术有机结合,在获得良好晶形异质结构H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂的同时明显缩短了光催化剂的制备周期,从而降低了催化剂的制备成本,攻克了光催化剂工业化应用的主要矛盾,所制备的H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂轻质油脱氮效率达97%以上。     

Excess capacity on compound phases of Li2FeTiO4 composite cathode materials synthesized by hydrothermal reaction using optional titanium sources to boost battery performance

Li₂FeTiO₄ composites have been produced using commercial LiAC, FeCl₂ and different titanium sources by hydrothermal synthesis (HS) at 175 ℃ and subsequent annealing at 700 ℃. Impure phase TiO₂, Fe₂O₃ and FeTiO₄ were detected out among the Li₂FeTiO₄ composites with different titanium sources. Micron and nano-sized particles of Li₂FeTiO₄ were prepared from various titanium raw materials, with nano-sized particles predominating when titanium raw materials were layered hydrogen titanate nanowire (H₂Ti₃O₇NW, HTO-NW) and titanium oxide nanotubes (TiO₂NB). The Li₂FeTiO₄ composites synthesized by HTO-NW shows a primary particle size of 50-200 nm of high crystallinity staggered with undissolved nanowire with a diameter size of about 100 nm. The samples using one-dimensional nanometer titanium oxide (TiO₂ NB) as the raw material can get a super high initial discharge capacity of 367.8 mAh/g at the rate of C/10 and excellent cycling stability. The selection of raw materials and adopting multi-phase modification can be considered as an effective strategy to improve the electro-chemical properties of Li₂FeTiO₄ composite cathode materials for the lithium secondary battery.     

光热效应增强的Au/RGO/Na2Ti3O7光催化加氢性能

将典型的光热等离激元石墨烯和纳米金简便地负载在钛酸钠(Na₂Ti₃O₇)载体上, 构建出具有较窄禁带宽度和较高光催化活性的Au/RGO/Na₂Ti₃O₇光热辅助光催化体系. 研究发现, 石墨烯片层与金纳米颗粒在光照下, 通过局域表面等离激元共振效应诱导产生大量的热电子, 以活化反应物并降低反应活化能, 其引发的光热效应还可精准提升光催化体系中反应位点附近的温度, 从而大幅提升光催化反应速率. 通过构建特殊微支结构, 进一步增强了Au/RGO/Na₂Ti₃O₇催化剂对光的捕获, 并限域锚定高表面能催化剂以增强体系的稳定性. 在光热、 光催化的高效协同增强下, Au/RGO/Na₂Ti₃O₇催化剂体系对对硝基苯酚和肉桂醛的加氢反应均表现出增强的光催化活性. 光热辅助下的Au/RGO/Na₂Ti₃O₇光催化剂在对硝基苯酚反应中的转换频率（TOF）值高达54.4 min^-1, 反应活化能显著降低至15.78 kJ/mol, 且其在长效测试中表现出良好的稳定性（4次循环催化后, 转化率的保持率近90%）.     

One-step solvothermal synthesis of N-doped TiO2 nanoparticles with high photocatalytic activity in the reduction of aqueous Cr（Ⅵ）

N-doped TiO2 （N-TiO2） nanoparticles were synthesized via a one-step low temperature （180℃） solvothermal route, which adopted NH4NO3 as the nitrogen source. The structure, composition, BET specific surface area, and optical properties of the as-synthesized product were characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, N2 adsorption- desorption isotherms, and UV-vis diffuse reflectance spectroscopy. In addition, its photocatalytic properties were tested by the reduction of aqueous Cr（VI） under UV and visible light （x 〉 420 rim） irradiation. It was observed that for the reduction of aqueous Cr（VI）, the as-synthesized N-TiO2 nanoparticles not only exhibited much higher photocatalytic activity than P25 TiO2 under UV light, but also exhibited remarkably high photocatalytic activity under visible light （λ 〉 420 nm）.     

Bi_(20)TiO_(32)/聚丙烯腈复合纳米纤维的制备及其对异丙隆的光催化降解性能

采用溶剂热法制备了可见光响应型光催化剂Bi_(20)TiO_(32),为了实现该光催化剂的固定化负载,进一步以Bi_(20)TiO_(32)和聚丙烯腈(PAN)为原料,通过同轴静电纺丝法制备了不同光催化剂含量的Bi_(20)TiO_(32)/PAN复合纳米纤维。通过这一途径一方面可以便于光催化剂的回收利用,另一方面纳米纤维结构可以提高光催化剂与有机污染物反应的接触面积。采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)和氮气吸附-脱附法对样品的物相组成、形貌结构、光谱吸收和比表面积等进行表征。研究了在可见光照射下Bi_(20)TiO_(32)/PAN复合纳米纤维膜对苯脲类农药异丙隆的光催化降解性能。结果显示,制备的Bi_(20)TiO_(32)光催化剂禁带宽度为2.35 eV,属于典型的可见光响应型光催化剂。制备的Bi_(20)TiO_(32)/PAN复合纳米纤维直径在600~700 nm,Bi_(20)TiO_(32)可以在纳米纤维表面均匀负载,复合纳米纤维膜对可见光具有明显的响应性,对异丙隆具有很好的光催化降解效果,其中光催化剂质量分数为25.7%的样品S3对异丙隆的降解率最高可达到87%。这一研究表明,通过同轴静电纺丝法将光催化剂负载于有机纳米纤维表面,可以保持光催化剂原有光催化效果,是实现光催化剂固定化一条较好的途径。     

高催化活性2D/2D Ti3C2/Bi4O5Br2纳米片异质结的构建及其可见光催化去除NO

This study concentrated on the production of a two-dimensional and two-dimensional (2D/2D) Ti₃C₂/Bi₄O₅Br₂ heterojunction with a large interface that applied as one of the novel visible-light-induced photocatalyst via the hydrothermal method. The obtained photocatalysts enhanced the photocatalytic efficiency of the NO removal. The crystal structure and chemical state of the composites were characterized using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The results showed that Ti₃C₂, Bi₄O₅Br₂, and Ti₃C₂/Bi₄O₅Br₂ were successfully synthesized. The experimental results of scanning electron microscopy (SEM) and transmission electron microscopy (TEM) showed that the prepared samples had a 2D/2D nanosheet structure and large contact area. This structure facilitated the transfer of electrons and holes. The solar light absorptions of the samples were evaluated using the UV-Vis diffuse reflectance spectra (UV-Vis DRS). It was found that the absorption band of Ti₃C₂/Bi₄O₅Br₂ was wider than that of Bi₄O₅Br₂. This represents the electrons in the Ti₃C₂/Bi₄O₅Br₂ nanosheet composites were more likely to be excited. The photocatalytic experiments showed that the 2D/2D Ti₃C₂/Bi₄O₅Br₂ composite with high photocatalytic activity and stability. The photocatalytic efficiency of pure Bi₄O₅Br₂ for the NO removal was 30.5%, while for the 15%Ti₃C₂/Bi₄O₅Br₂ it was 57.6%. Moreover, the catalytic reaction happened in a short period. The concentration of NO decreased exponentially in the first 5 min, which approximately reached the final value. Furthermore, the stability of 15%Ti₃C₂/Bi₄O₅Br₂ was favorable: the catalytic rate was approximately 50.0% after five cycles of cyclic catalysis. Finally, the scavenger experiments, electron spin resonance spectroscopy (ESR), transient photocurrent response, and surface photovoltage spectrum (SPS) were applied to analyze the photocatalytic mechanism of the composite. The results indicated that the 2D/2D heterojunction Ti₃C₂/Bi₄O₅Br₂ improved the separation rate of the electrons and holes, thus enhancing the photocatalytic efficiency. In the photocatalytic reactions, the photogenerated electrons (e⁻) and superoxide radical (·O₂⁻) were critical active groups that had a significant role in the oxidative removal of NO. The in situ Fourier-transform infrared spectroscopy (in situ FTIR) showed that the photo-oxidation products were mainly NO₂⁻ and NO₃⁻. Based on the above experimental results, a possible photocatalytic mechanism was proposed. The electrons in Bi₄O₅Br₂ were excited by visible light. They jumped from the valence band (VB) of Bi₄O₅Br₂ to the conduction band (CB). Then, the photoelectrons transferred from the CB of Bi₄O₅Br₂ to the Ti₃C₂ surface, which significantly promoted the separation of the electron-hole pairs. Therefore, the photocatalytic efficiency of Ti₃C₂/Bi₄O₅Br₂ on NO was significantly improved. This study provided an effective method for preparing 2D/2D Ti₃C₂/Bi₄O₅Br₂ nanocomposites for the photocatalytic degradation of environmental pollutants, which has great potential in solving energy stress and environmental pollution.     

SERS Study of Co-doped TiO2 Nanoparticles

Single-phase Co-doped TiO₂(Co_xTi_1-xO₂) nanoparticles(NPs) synthesized via a simple sol-hydrothermal method were used as surface-enhanced Raman scattering(SERS) substrates. Interestingly, it was found that SERS signals were enhanced greatly compared to those of pure TiO₂ nanoparticles when an amount of Co²⁺ ions were doped into the TiO₂ lattice. Detailed results clearly show that Co element as Co²⁺ was incorporated into the TiO₂ lattice and the defects were created due to the substitution of Co²⁺ ions for the Ti⁴⁺ ions. The Co²⁺ doping increases the defect concentration of Co_xTi_1-xO₂ NPs. An amount of defects is beneficial to the charge-transfer so as to increase the SERS activities. A possible mechanism of charge-transfer from Co_xTi_1-xO₂ NPs to molecules was then briefly discussed.     

MoS_2负载量对MoS_2/TiO_2光催化降解苯酚效率的影响及其作用机理研究

通过水解法制备TiO_2纳米颗粒,与经过超声处理后的MoS_2片层纳米材料复合制备MoS_2/TiO_2纳米催化剂,考察不同MoS_2负载量对其光催化降解苯酚效率及路径的影响。XRD、SEM、EDS、FT-IR和UV-vis DRS等表征结果表明,复合催化剂主要由锐钛矿型TiO_2和MoS_2组成;剥离后的MoS_2呈现薄片层状结构,均匀地分散在TiO_2纳米颗粒当中。光催化降解苯酚性能测试结果显示,对于MoS_2/TiO_2催化剂,MoS_2负载量的提高有利于光催化降解苯酚效率的提高;当MoS_2负载量为27%时,复合M o S2/TiO_2纳米颗粒的光催化性能最佳,反应80 min后可将苯酚完全降解。通过对苯酚降解过程中生成中间产物跟踪发现,MoS_2负载量的提高有利于促进中间产物苯醌、对苯二酚以及邻苯二酚的生成,进而提升了MoS_2/TiO_2复合材料的光催化性能。     

钨酸铋量子点和纳米片修饰石墨相氮化碳复合催化剂的制备及其可见光催化活性增强

利用超声-水热法、使用油酸钠辅助合成钨酸铋(Bi₂WO₆)量子点/纳米片修饰的石墨相氮化碳(g-C₃N₄)(Bi₂WO₆/g-C₃N₄)复合光催化剂。 通过X射线粉末衍射(XRD)、透射电子显微镜(TEM)、傅里叶变换红外光谱(FT-IR)、紫外可见漫反射光谱(UV-Vis DRS)、N₂吸附-脱附等技术手段获得Bi₂WO₆/g-C₃N₄催化剂的组成、结构和光吸收性能,分析合成机理。 以罗丹明B(RhB)水溶液为模拟污染物,考察Bi₂WO₆/g-C₃N₄复合催化剂的可见光催化活性。 结果表明:g-C₃N₄和Bi₂WO₆的质量比为3:7的Bi₂WO₆/g-C₃N₄-30具有最有效的异质界面,电化学阻抗和光电流测试结果显示该催化剂的光生载流子传输速率快、复合率低,可见光照射120 min对RhB的降解率达到95.8%;通过活性物质捕捉实验获知光生空穴是光催化反应中的主要活性物质,分析异质界面对光催化活性的影响,进而提出光催化反应机理。     

凹凸棒黏土负载纳米TiO2-Fe3O4吸附剂的制备及Cr(Ⅵ)的脱除

采用溶胶-凝胶法、一锅反应法制备了负载纳米TiO₂和Fe₃O₄的凹凸棒黏土(TiO₂-Fe₃O₄-ATP)吸附剂,并进行了模拟废水中Cr(Ⅵ)的吸附及脱附性能的研究。 通过扫描电子显微镜(SEM)、X射线衍射(XRD)、傅里叶变换红外光谱(FT-IR)和EDS等分析方法对ATP负载纳米TiO₂-Fe₃O₄前后结构进行了表征,考察了物料配比及吸附时间、pH值、温度、投加量和初始质量浓度对Cr(Ⅵ)吸附率的影响。 结果表明,吸附剂在Ti元素含量与负载总量的摩尔比为3：4时吸附效果最佳。 当吸附剂质量为0.6 g,Cr(Ⅵ)离子初始质量浓度小于0.8 mg/L时,pH=6,温度20 ℃,吸附剂对Cr(Ⅵ)的吸附率为79.8%。 TiO₂-Fe₃O₄-ATP吸附剂对Cr(Ⅵ)离子吸附满足Freundlich模型。 在20~40 ℃ 条件下,吸附过程ΔG<0、ΔS=-43.55 J/(mol·K)、ΔH=-14.36 kJ/mol,表明该吸附是个自发、熵减、放热的过程。 吸附过程符合准二级动力学模型,吸附速率控制步骤以表面化学反应为主。 TiO₂-Fe₃O₄-ATP吸附剂在循环使用4次后,吸附率仍能达到65%以上。