Effect of surfactants on shear-induced gelation and gel morphology of soft strawberry-like particles

The role of surfactant type in the aggregation and gelation of strawberry-like particles induced by intense shear without any electrolyte addition is investigated. The particles are composed of a rubbery core, partially covered by a plastic shell, and well stabilized by fixed (sulfate) charges in the end group of the polymer chains originating from the initiator. In the absence of any surfactant, after the system passes through a microchannel at a Peclet number equal to 220 and a particle volume fraction equal to 0.15, not only shear-induced gelation but also partial coalescence among the particles occurs. The same shear-induced aggregation/gelation process has been carried out in the presence of an ionic (sulfonate) surfactant or a nonionic (Tween 20) steric surfactant. It is found that for both surfactants shear-induced gelation does occur at low surfactant surface density but the conversion of the primary particles to the clusters constituting the gel decreases as the surfactant surface density increases. When the surfactant surface density increases above certain critical values, shear-induced gelation and eventually even aggregation do not occur any longer. For the sulfonate surfactant, this was explained in the literature by the non-DLVO, short-range repulsive hydration forces generated by the adsorbed surfactant layer. In this work, it is shown that the steric repulsion generated by the adsorbed Tween 20 layer can also protect particles from aggregation under intense shear. Moreover, the nonionic steric surfactant can also protect the strawberry-like particles from coalescence. This implies a decrease in the fractal dimension of the clusters constituting the gel from 2.76 to 2.45, which cannot be achieved using the ionic sulfonate surfactant.     

Shear-induced structure in polymer-clay nanocomposite solutions

The equilibrium structure and shear response of model polymer-clay nanocomposite gels are measured using X-ray scattering, light scattering, optical microscopy, and rheometry. The suspensions form physical gels via the "bridging" of neighboring colloidal clay platelets by the polymer, with reversible adsorption of polymer segments onto the clay surface providing a short-range attractive force. As the flow disrupts this transient network, coupling between composition and stress leads to the formation of a macroscopic domain pattern, while the clay platelets orient with their surface normal parallel to the direction of vorticity. We discuss the shear-induced structure, steady-shear rheology, and oscillatory-shear response of these dynamic networks, and we offer a physical explanation for the mesoscale shear response. In contrast to flow-induced "banding" transitions, no stress plateau is observed in the region where macroscopic phase separation occurs. The observed platelet orientation is different from that reported for polymer-melt clay nanocomposites, which we attribute to effects associated with macroscopic phase separation under shear flow.     

酶凝干酪素物理凝胶化过程的有限元模拟

以酶凝干酪素的凝胶化过程为对象,利用有限元方法数值分析了在凝胶化过程中温度场的空间分布和时间演变规律.在此基础上,基于一阶的凝胶化动力学方程,数值模拟了凝胶体系的复剪切模量场,进而分析了材料配方、体系尺寸与冷却方案对复剪切模量场的影响规律.模拟结果表明,由于热阻的差异,体系表面的冷却速率大于内部,表面首先发生凝胶化;而由于预凝胶化阶段的平均冷却速率决定了无穷复剪切模量的值,最终体系内部的复剪切模量超过表面的.     

Orientation and relaxation of polymer–clay solutions studied by rheology and small-angle neutron scattering

The influence of shear on viscoelastic solutions of poly(ethylene oxide) (PEO) and clay [montmorillonite, i.e., Cloisite NA+ (CNA)] was investigated with rheology and small-angle neutron scattering (SANS). The steady-state viscosity and SANS were used to measure the shear-induced orientation and relaxation of the polymer and clay platelets. Anisotropic scattering patterns developed at much lower shear rates than in pure clay solutions. The scattering anisotropy saturated at low shear rates, and the CNA clay platelets aligned with the flow, with the surface normal parallel to the gradient direction. The cessation of shear led to partial and slow randomization of the CNA platelets, whereas extremely fast relaxation was observed for laponite (LRD) platelets. These PEO–CNA networklike solutions were compared with previously reported PEO–LRD networks, and the differences and similarities, with respect to the shear orientation, relaxation, and polymer–clay interactions, were examined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3102–3112, 2004     

Rheology of aqueous carbon black dispersions

The interaction of carbon black with an acrylic resin has been investigated by rheology. Two carbon blacks, with similar particle size and surface characteristics but quite different particle morphologies, have been examined. These are somewhat arbitrarily denoted as "spherical" and "fractal" as shown by small-angle neutron scattering (SANS) and ultrasonic spectroscopy studies. In the absence of polymer, stable aqueous dispersions could not be obtained. Stable dispersions could be obtained, however, upon addition of polymer to a level corresponding to a ratio of 50 mg of polymer per 13 m2 (+/- m2) of surface area (i.e., 15 wt% particles). These stable dispersions exhibit flow typical of concentrated dispersions-Newtonian behavior up to some apparent "yield" or critical value, above which pronounced shear thinning is observed. The critical stress increases with increasing polymer concentration. When a significant amount of nonadsorbed polymer is also present, a second Newtonian plateau is superimposed on the shear-thinning behavior. This feature is observed for both particle types but is more pronounced for the fractal particle. When there is little or no nonadsorbed polymer, the viscosity of the fractal particle dispersions is greater than the viscosity of the spherical particle dispersions. At low polymer concentrations, the dispersions are predominantly viscous at low shear stresses. The phase angle decreases significantly over a narrow shear stress range and the rheology tends to more elastic behavior. At higher shear stresses, the dependence on particle morphology is weak.     

Flocculation and reflocculation of clay suspension by different polymer systems under turbulent conditions

The focused beam reflectance measurement (FBRM), also known as scanning laser microscopy (SLM), was used as a real-time monitor to study the flocculation and reflocculation of clay suspensions under different shear conditions in the presence of single polymer, dual polymer, microparticle and poly(ethylene oxide)/phenolformaldehyde (PEO/PFR) flocculation systems. For initial flocculation, the high molecular weight PEO and cationic polyacrylamide (CPAM) produced larger flocs than others. However, reflocculation of clay suspensions formed by these non- or low-charged polymers was insignificant after the initial flocs were broken under high shear force. In contrast, high charge density polymers, such as poly(diallyldimethylammonium chloride) (PDADMAC), do not form large initial flocs, but they showed significant reflocculation ability under a continuous shear condition. It is concluded that high flocculation can be obtained by effective polymer bridging, but high reflocculation can only be induced by high electrostatic attractive forces between suspended particles.     

Morphology and properties of waterborne adhesives made from hybrid polyacrylic/montmorillonite clay colloidal dispersions showing improved tack and shear resistance

The morphology and adhesive properties of waterborne films from n-butyl acrylate/methyl methacrylate/montmorillonite clay hybrid polymer latexes which were synthesized by miniemulsion polymerization in the presence of a reactive organoclay ((2-methacryloylethyl) hexadecyldimethylammonium modified montmorillonite, CMA16) were investigated. It was found by cryo-TEM analysis that the hybrid dispersions were a mixture of colloidal particles composed of a small fraction of free montmorillonite clay platelets, polymer latex particles, polymer particles to which one or more clay platelets where adhered onto its surface and a fraction of colloidal material consisted of a clay platelet with a polymer lob adhered to either side, in other words hybrid particles with a dumbbell-like morphology. The films made from these waterborne hybrid dispersions presented a homogeneous dispersion of the clay platelets and exfoliated morphology. The shear adhesion failure temperature (SAFT) and shear resistance of the hybrid latex films synthesized with CMA16 were better than those prepared with a commercial clay (Cloisite 30B), but presented a liquid-like probe-tack performance. When allyl methacrylate (AMA) was added in the formulation, SAFT and shear resistance improved, but the film had a very low energy of adhesion due to the excessively crosslinked matrix. In order to reduce crosslink density and thus improve the adhesion energy, small amounts of chain transfer agent, in this case n-dodecyl mercaptan (n-DDM), were used in the miniemulsion polymerization process. Adhesive films made from these waterborne hybrid dispersions showed excellent SAFT and shear resistance, and good energy of adhesion.      

In situ small-angle neutron scattering and rheological measurements of shear-induced gelation

The microscopic structure of shear-induced gels for a mixed solution of 2-hydroxyethyl cellulose and nanometer-size spherical droplets has been investigated by in situ small-angle neutron scattering (SANS) with a Couette geometry as a function of shear rate gamma. With increasing gamma, the viscosity increased rapidly at gamma approximately 4.0 s(-1), followed by a shear thinning. After cessation of shear, the system exhibited an extraordinarily large steady viscosity. This phenomenon was observed as a shear-induced sol-gel transition. Real-time SANS measurements showed an increase in the scattering intensity exclusively at low scattering angle region. However, neither orientation of polymer chains nor droplet deformation was detected and the SANS patterns remained isotropic irrespective of gamma. It took about a few days for the gel to recover its original sol state. A possible mechanism of gelation is proposed from the viewpoint of shear-induced percolation transition.     

Surface shear rheology of WPI-monoglyceride mixed films spread at the air-water interface

Surface shear viscosity of food emulsifiers may contribute appreciably to the long-term stability of food dispersions (emulsions and foams). In this work we have analyzed the structural, topographical, and shear characteristics of a whey protein isolate (WPI) and monoglyceride (monopalmitin and monoolein) mixed films spread on the air-water interface at pH 7 and at 20 degrees C. The surface shear viscosity (etas) depend on the surface pressure and on the composition of the mixed film. The surface shear viscosity varies greatly with the surface pressure. In general, the greater the surface pressure, the greater are the values of etas. The values of etas for the mixed WPI-monoolein monolayer were more than one order of magnitude lower than those for a WPI-monopalmitin mixed film, especially at the higher surface pressures. At higher surface pressures, collapsed WPI residues may be displaced from the interface by monoglyceride molecules with important repercussions on the shear characteristics of the mixed films. A shear-induced change in the topography and a segregation between domains of the film forming components were also observed. The displacement of the WPI by the monoglycerides is facilitates under shear conditions, especially for WPI-monoolein mixed films.     

Sol–gel transition and rheological properties of silica nanoparticle dispersions

Possible variants of the rheological behavior of silica model dispersions have been analyzed. Different types of interaction between the particles and a dispersion medium make it possible to obtain different systems from low-viscosity sols to gels. Proton-donor (water) and aprotic (dimethyl sulfoxide) media have been used for comparison. Dispersions in the aprotic medium behave as non-Newtonian viscous fluids exhibiting shear thinning or shear thickening depending on deformation rate. Aqueous dispersions are viscoelastic and viscoplastic objects that exhibit the shear thickening at stresses higher than the yield stress. The introduction of small amounts of poly(ethylene oxide) into the organic dispersion medium initiates gelation. An increase in the polymer content in the dispersion medium above the concentration corresponding to the formation of a macromolecular network promotes an increase in stiffness and strength of the gels. The rheological behavior of gels is influenced by the polymer molecular mass and its affinity for a solvent.     

Dynamic yielding, shear thinning, and stress rheology of polymer-particle suspensions and gels

The nonlinear rheological version of our barrier hopping theory for particle-polymer suspensions and gels has been employed to study the effect of steady shear and constant stress on the alpha relaxation time, yielding process, viscosity, and non-Newtonian flow curves. The role of particle volume fraction, polymer-particle size asymmetry ratio, and polymer concentration have been systematically explored. The dynamic yield stress decreases in a polymer-concentration- and volume-fraction-dependent manner that can be described as apparent power laws with effective exponents that monotonically increase with observation time. Stress- or shear-induced thinning of the viscosity becomes more abrupt with increasing magnitude of the quiescent viscosity. Flow curves show an intermediate shear rate dependence of an effective power-law form, becoming more solidlike with increasing depletion attraction. The influence of polymer concentration, particle volume fraction, and polymer-particle size asymmetry ratio on all properties is controlled to a first approximation by how far the system is from the gelation boundary of ideal mode-coupling theory (MCT). This emphasizes the importance of the MCT nonergodicity transition despite its ultimate destruction by activated barrier hopping processes. Comparison of the theoretical results with limited experimental studies is encouraging.     

Steady-shear and viscoelastic properties of cellulose nanofibril–nanoclay dispersions

We have investigated the steady-shear and viscoelastic properties of composite dispersions of cellulose nanofibrils (CNFs) with medium or high charge density and two different nanoclays, viz. rod-like sepiolite or plate-like bentonite. Aqueous dispersions of CNFs with medium charge density displayed significantly lower steady-state viscosity and storage modulus but higher gelation threshold compared with CNFs with high charge density. Dynamic light scattering (DLS) results showed that the apparent hydrodynamic radius of bentonite particles increased when CNFs were added, implying that CNFs adsorbed onto the amphoteric edges of the plate-like bentonite particles. The sepiolite network in CNF–sepiolite dispersions was relatively unaffected by addition of small amounts of CNFs, and DLS showed that the hydrodynamic radius of sepiolite did not change when CNFs were added. Addition of CNFs at concentrations above the gelation threshold resulted in drastic decrease of the steady-shear viscosity of the sepiolite dispersion, suggesting that the sepiolite network disintegrates and the rod-like clay particles are aligned also at low shear rate. The relative change in the rheological properties of the clay-based dispersions was always greater on addition of CNFs with high compared with medium charge density. This study provides insight into how the rheology of CNF–nanoclay dispersions depends on both the nanoclay morphology and the interactions between the nanoclay and nanocellulose particles, being of relevance to processing of nanocellulose–clay composites.     

聚苯乙烯/蒙脱土纳米复合材料的自组装行为

聚合物／层状硅酸盐（PLS）纳米复合材料由于具有常规复合材料所没有的结构、形态以有较常规聚合物基复合材料更优异的物理力学性能等而引起人们的关注^[1],但以往文献^[1-3]主要报道PLS纳米复合材料的制备与性能表征,对于熔融加工过程中粘土粒子吸高分子的取向和结构研究很少。作者等^[4-6]发现了剥离型聚苯乙烯（PS）／蒙脱土纳米复合材料中的剪切诱导有序结构,并采用广角X射线衍射法（WAXD）、透射电镜法（TEM）和红外二向色性法对其形成机理进行了研究。结果表明,该有序结构的主要来源是分散在PS基体中的蒙脱土初级粒子（Primary particles）内部片层的规整排列以及沿平行于样品表面方面的平面取向,PS的苯环平面平行剪切流动方向取向,而烷项链未见明显取向。本文报道该纳米复合材料的剪切诱导有序结构在升温过程中出现的自组装行为,并用原位升温X射线衍射法和红外二向色性法对蒙脱土初级粒子的规整度以及PS的苯环和烷基链在升温过程中的取向行为进行了研究,在此基础上提出了可能的形成机理。     

Improved dewatering behavior of clay minerals dispersions via interfacial chemistry and particle interactions optimization

Orthokinetic flocculation of clay dispersions at pH 7.5 and 22 degrees C has been investigated to determine the influence of interfacial chemistry and shear on dewatering and particle interactions behavior. Modification of pulp chemistry and behavior was achieved by using kaolinite and Na-exchanged (swelling) smectite clay minerals, divalent metal ions (Ca(II), Mn(II)) as coagulants and anionic polyacrylamide copolymer (PAM A) and non-ionic polyacrylamide homopolymer (PAM N) as flocculants. The pivotal role of shear, provided by a two-blade paddle impeller, was probed as a function of agitation rate (100-500 rpm) and time (15/60 s). Particle zeta potential and adsorption isotherms were measured to quantify the interfacial chemistry, whilst rheology and cryogenic SEM were used to investigate particle interactions and floc structure and aggregate network, respectively. Osmotic swelling, accompanied by the formation of "honeycomb" particle network structure and high yield stress, was produced by the Na-exchanged smectite, but not kaolinite, dispersions. Dispersion of the clay particles in 0.05 M Ca(II) or Mn(II) solution led to a marked reduction in particle zeta potential, complete suppression of swelling, honeycomb network structure collapse and a concomitant reduction in shear yield stress of smectite pulps. Optimum conditions for improved, orthokinetic flocculation performance of negatively charged clay particles, reflecting faster settling flocs comprised (i) coagulation, (ii) moderate agitation rate, (iii) shorter agitation time, and (iv) anionic rather than non-ionic PAM. The optimum dewatering rates were significantly higher than those produced by standard, manual-mixing flocculation techniques (plunging and cylinder inversion) commonly used in industry for flocculant trials. The optimum flocculation conditions did not, however, have a significant impact on the final sediment solid content of 20-22 wt%. Further application of shear to pre-sedimented pulps improved consolidation by 5-7 wt% solid. Higher shear yield stresses and greater settling rates were displayed by PAM A based than PAM N based pulps and this is attributed to the former's more expanded interfacial conformation and greater clay particles bridging ability. It appears that the intrinsic clay particles' physico-chemical properties and interactions limit compact pulp consolidation.     

Controlled association in suspensions of charged nanoparticles with a weak polyelectrolyte

The properties of high-pH suspensions of mixtures of silica with low-molecular-weight samples of the water-soluble polymer polyethylenimine (PEI) have been studied. At pH > 10 and low ionic strength, silica nanoparticles are stabilized by a negative surface charge, and PEI has only a very low positive charge. The adsorption of PEI induces a localized positive charge on the segments of polymer closest to the silica surface. The parts of the molecule furthest away from the surface have little charge because of the high pH of the medium. The polymer-covered particle remains negatively charged, imparting some electrostatic stabilization. Suspensions of silica and low-molecular-weight PEI are low-viscosity fluids immediately after mixing, but aggregation occurs leading to the eventual gelation (or sedimentation at lower concentrations) of these mixtures, indicating colloidal instability. The gelation time passes through a minimum with increasing surface coverage. The rate of gelation increases exponentially with molecular weight: for molecular weight > or = 10,000 Da PEI, the instability is so severe that uniform suspensions cannot be produced using simple mixing techniques. The gelation rates increase rapidly with temperature, ionic strength, and reduction in pH. The rate of gelation increases with increasing particle concentration at low surface coverage but decreases at high coverage as a consequence of a small increase in pH. Gels are broken by application of high shear into aggregates that re-gel more rapidly than the original discrete coated particles.     

Preparation and characterization of multilayered polymer nanotube dispersions

Despite considerable efforts to synthesize nanotubes using porous alumina or polycarbonate membrane templates, few studies have addressed the resulting nanotube dispersion. We prepared dispersions of multilayered polyethylenimine/maleic anhydride alternating copolymer (PEI/MAAC) nanotubes synthesized with porous alumina templates. After mechanical polishing to remove the residual polymer surface layer from templates and subsequent template dissolution, the multilayered PEI/MAAC nanotubes were easily dispersed in water at neutral pH by polyelectrolyte adsorption, producing nanotube dispersions that were stable for at least 3 months. We characterized the dispersions using phase-contrast optical microscopy, electro-optics, electrophoresis, and viscometry to help understand their colloidal properties in the dilute and semidilute regimes. The dispersions were resistant to salt-induced aggregation up to at least 1 mM NaCl and were optically anisotropic when subjected to an electric field or flow. Interestingly, the electrophoretic mobility of polystyrene sulfonate (PSS)-stabilized nanotubes increases with increasing ionic strength, because of the high surface charge and softness of the adsorbed polyelectrolyte. Furthermore, unlike many rod-like colloid systems, the polymer nanotube dispersion has low viscosity because of weak rotary Brownian motions and strong tendency to shear thinning. At the high shear rates achieved in capillary viscometry experiments, however, we observed a slight shear thickening, which can be attributed to transient hydrocluster formation.     

Shear-induced crystallization in phase-separated blend of isotactic polypropylene and poly (ethylene-co-octene)

Isothermal crystallization after shear in a blend of isotactic polypropylene (iPP) and poly (ethylene-co-octene) (PEOc) was investigated by in situ optical microscopy and shear hot stage under various thermal and shear histories. Crystalline cylindrites during growth were observed in phase-separated iPPPEOc blends for the first time. According to our results, the very long cylindrites are formed which are much longer than the dimensions of the liquid-liquid phase-separated domains under shear, and the cylindrites appear to grow through noncrystallizable domains, as well as through crystallizable ones. Obviously, the nuclei ("shish") come from the oriented and entangled network strands instead of pulled-out long chains. The number of cylindrites and the distortion and breakup of the cylindrites are related to the shear rate and shear time. On the other hand, the number of spherulites increases not only with shear rate but also with liquid-liquid phase separation time. Spherulites always form with longer induction time than cylindrites due to the different nucleation mechanism. The shish is nucleated through the shear-induced mechanism, and most of the spherulites are nucleated through liquid-liquid spinodal decomposition and crossover after the cessation of shear. During the process of experiments, we also found three kinds of shish-kebab structures, which provide further physical insights into the mechanism of the shish formation in polymer blend after liquid-liquid phase separation under shear.     

Effects of particles on stability of flow-induced precursors

The effect of two colorant particles with different surface geometries on the stability of shear-induced precursors in isotactic polypropylene was studied after the cessation of shear flow at 140 °C. In the absence of particles, the shear-induced precursors survived for at least 100 s after the shear flow ended. The presence of particles was found to stabilize lower molecular weight chains assisting in the formation of additional shear-induced precursors. The precursors thus formed in the samples containing particles contained two oriented clusters with different molecular weights. Incorporation of lower molecular weight chains in the precursors led to increased dissolution rates of the shear-induced precursors. Particle surface geometry was found to influence precursor dissolution, with planar particles stabilizing the shear-induced precursors to a much greater extent than curved particles. The particles investigated thus act like structural probes to follow quantitatively the dissolution process of precursors after shear and importantly to infer the formation of precursors during shear.     

Plastic and elastic properties of the systems interstratified clay-water-electrolyte-xanthan

The present study concerns the rheological behavior of the Jebel Shemsi clay dispersions (Shp). Shp is an interstratified illite/smectite clay from southern Tunisia. The influences of clay concentration, NaCl, and xanthan-a semirigid polymer-on the yield stress, the elastic modulus, and the xanthan adsorption were investigated. The sol-gel transition and the scale laws of rheometric properties are established. Progressive addition of NaCl to the clay dispersions decreases the thickness of the diffuse double layer, which makes the system rigid, increasing the yield and the elastic modulus. In the presence of xanthan, the negative surface charges become higher and the repulsive interparticle interactions increase; consequently the yield and the elastic modulus increase. The xanthan adsorption on the clay particle surface increases slightly with the NaCl concentration. The particle aggregation due to the salt and the particle dispersion due to the polymer are observed. The behavior of this interstratified clay is compared to that found for pure smectite. The 15% illite stratified with smectite in the Shp clay does not change the gels' rheological properties significantly. Meanwhile the amount of Shp clay needed to obtain a gel is more important than in the case of a pure smectite.     

Effect of lithium salt on the stability of dispersions of fumed silica in the ionic liquid BMImBF4

We have investigated the stability and interactions in dispersions of colloidal fumed silica, Aerosil 200, and the ionic liquid 1-butyl-3-methylimidazolium tetraflouroborate (BMImBF(4)) as a function of the Li salt concentration (LiBF(4)). Photon correlation spectroscopy was used to study the aggregation behavior at low silica concentrations, and Raman spectroscopy was used to investigate the interactions in the ionic liquid and with the silica surface. We find that the addition of LiBF(4) increases the stability of the dispersions, with smaller agglomerates of silica particles and higher gelation concentrations in the presence of Li salt. The increased stability with the addition of Li salt is explained by the formation of a more stable solvation layer, where Li ions accumulate on the surface. This leads to an increased interaction between lithium ions and the BF(4)(-) anions in the solvation layer, as seen by Raman spectroscopy. Upon gelation, the Li ions are expelled from the surface because hydrogen bonding between the silica particles are formed. For both neat BMImBF(4) and Li-salt-doped BMImBF(4)/silica dispersions, a weak gel phase was found preceding the formation of a strong gel at slightly higher silica concentrations.