| 相位加权的矢量全聚焦超声阵列成像方法研究 |
| |
| 引用本文： | 焦敬品,杨素方,何存富,吴斌.相位加权的矢量全聚焦超声阵列成像方法研究[J].声学学报,2017,42(4):485-494. |
| |
| 作者姓名： | 焦敬品 杨素方 何存富 吴斌 |
| |
| 作者单位： | 1. 北京工业大学 机械工程与应用电子技术学院 北京 100124; |
| |
| 基金项目： | 国家自然科学基金项目(11572010,11272017)和国家重点研发计划项目(2016YFF0203002)资助 |
| |
| 摘 要： | 常规矢量全聚焦成像仅利用检测信号的幅值信息,其成像质量受噪声、栅瓣和旁瓣等的影响大。综合利用检测信号的幅值和相位信息,本文提出两种相位加权的矢量全聚焦成像方法。首先,对全矩阵数据的相位信息进行分析,提取出两种相位特征参数:相位一致因子(Phase Coherence Factor:PCF)和极性一致因子(Sign Coherence Factor:SCF);然后,将全阵列划分为若干子阵列,分别利用两种相位特征参数对各个子阵列的成像幅值进行加权,求取加权幅值特征向量;最后,对所有子阵列的加权特征向量进行合成,得到两种加权的矢量全聚焦成像,并从中提取出裂纹方向及尺寸等特征信息。将三种矢量全聚焦成像方法应用于不同缺陷检测仿真及实验验证,结果表明,3种方法均可以实现缺陷方向识别与长度定量测量;但相位加权矢量全聚焦成像效果明显优于常规矢量全聚焦成像结果,其成像信噪比及分辨率更高,缺陷角度及长度测量结果更准确。本文研究工作为缺陷无损评价提供了可行的技术手段。
|
| 关 键 词： | 超声阵列 子阵列 相位信息 矢量全聚焦 |
| 收稿时间： | 2016-01-25 |
Investigation of an ultrasonic array imaging method of phase weighting vector total focusing |
| |
| Affiliation: | 1. College of Mechanical Engineering and Application Electronics Technology, Beijing University of Technology Beijing 100124;2. Beijing Engineering Research Center of Precision Measurement Technology & Instruments, Beijing University of Technology Beijing 100124 |
| |
| Abstract: | The conventional vector total focusing method only uses the signal amplitude information, resulting in the imaging quality very affected by the noise, grating lobes, side lobes and so on. In this paper, the signal amplitude and phase information are used together, and then puts forward two kinds of phase weighting vector total focusing method. First, It is based on an analysis of the phase information at the full matrix data, two phase feature parameters, namely the phase coherence factor (PCF) and the sign coherence factor (SCF) are proposed; Then, the whole array is divided into a number of sub-arrays, using the two phase feature parameters to weight the imaging amplitude and consequently to get the weighted amplitude feature vector; finally, compounding the weighted amplitude feature vector of all sub-arrays, the new method for characterizing reflectors is presented, that is phase weighting vector total focusing method. In the simulation and experiment, above three kinds of vector total focusing methods was applied to defects detection. It turned out that the three methods can all achieve direction recognition and length quantitative measurement of defects, but the phase weighting method results is obviously superior to the conventional method results, the methods obtain improvements in SNR and resolution, and the direction and length measurement of defects are more accurate. The research work for the defect non-destructive evaluation provides a feasible method. |
| |
| Keywords: | |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《声学学报》浏览原始摘要信息 |
|
点击此处可从《声学学报》下载全文 |
|
